Skip to contentSkip to conversation

hwmon: (adt7475) Add support for the

PATCH In review Jean Delvare 1 participant 1 message Dec 2, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 4/11 hwmon: (adt7475) Add support for the

Add support for the Analog Devices ADT7490 chip. This chip is largely compatible with the ADT7473 and ADT7475, with additional features. In particular, it has 6 voltage inputs instead of 2.

Cc Hans de Goede <[email protected]>
Cc Jordan Crouse <[email protected]>
Cc "Darrick J. Wong" <[email protected]>
---
 Documentation/hwmon/adt7475 |   34 ++++++++++--
 drivers/hwmon/Kconfig       |    4 -
 drivers/hwmon/adt7475.c     |  115 ++++++++++++++++++++++++++++++++++++++-----
 3 files changed, 134 insertions(+), 19 deletions(-)
Documentation/hwmon/adt7475 +29 -5
@@ -10,24 +10,31 @@ Supported chips:
     Prefix: 'adt7475'
     Addresses scanned: I2C 0x2E
     Datasheet: Publicly available at the On Semiconductors website
+  * Analog Devices ADT7490
+    Prefix: 'adt7490'
+    Addresses scanned: I2C 0x2C, 0x2D, 0x2E
+    Datasheet: Publicly available at the On Semiconductors website
 
 Authors:
 	Jordan Crouse
 	Hans de Goede
 	Darrick J. Wong (documentation)
+	Jean Delvare
 
 
 Description
 -----------
 
-This driver implements support for the Analog Devices ADT7473 and ADT7475
-chip family. Both chips differ only in minor details. They will be
-collectively designed by the name "ADT747x" in the rest of this document.
+This driver implements support for the Analog Devices ADT7473, ADT7475 and
+ADT7490 chip family. The ADT7473 and ADT7475 differ only in minor details.
+The ADT7490 has additional features, including extra voltage measurement
+inputs and PECI support. All the supported chips will be collectively
+designed by the name "ADT747x" in the rest of this document.
 
 The ADT747x uses the 2-wire interface compatible with the SMBus 2.0
 specification. Using an analog to digital converter it measures three (3)
-temperatures and two (2) voltages. It has four (4) 16-bit counters for
-measuring fan speed. There are three (3) PWM outputs that can be used
+temperatures and two (2) or more voltages. It has four (4) 16-bit counters
+for measuring fan speed. There are three (3) PWM outputs that can be used
 to control fan speed.
 
 A sophisticated control system for the PWM outputs is designed into the
@@ -45,6 +52,23 @@ The ADT747x samples all inputs continuou
 the registers more often than once every other second. Further,
 configuration data is only read once per minute.
 
+Chip Differences Summary
+------------------------
+
+ADT7473:
+  * 2 voltage inputs
+  * system acoustics optimizations (not implemented)
+
+ADT7475:
+  * 2 voltage inputs
+
+ADT7490:
+  * 6 voltage inputs
+  * 1 Imon input (not implemented)
+  * PECI support (not implemented)
+  * 2 GPIO pins (not implemented)
+  * system acoustics optimizations (not implemented)
+
 Special Features
 ----------------
 
drivers/hwmon/Kconfig +2 -2
@@ -205,11 +205,11 @@ config SENSORS_ADT7473
 	  will be called adt7473.
 
 config SENSORS_ADT7475
-	tristate "Analog Devices ADT7473 and ADT7475"
+	tristate "Analog Devices ADT7473, ADT7475 and ADT7490"
 	depends on I2C && EXPERIMENTAL
 	help
 	  If you say yes here you get support for the Analog Devices
-	  ADT7473 and ADT7475 hardware monitoring chips.
+	  ADT7473, ADT7475 and ADT7490 hardware monitoring chips.
 
 	  This driver can also be build as a module.  If so, the module
 	  will be called adt7475.
drivers/hwmon/adt7475.c +98 -12

222 lines not on this page · raw message

}

+ if (data->has_voltage & (1 << 5)) {
+ data->voltage[MIN][5] = adt7475_read(REG_VTT_MIN) << 2;
+ data->voltage[MAX][5] = adt7475_read(REG_VTT_MAX) << 2;
+ }
+
for (i = 0; i < ADT7475_TEMP_COUNT; i++) {
/* Adjust values so they match the input precision */ data->temp[MIN][i]

Signature · 6 lines
Jean Delvare

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors