Skip to contentSkip to conversation

hwmon: (smsc47m1) Enable device if needed

PATCH New Jean Delvare 1 participant 1 message Dec 6, 2009 Hardware monitoring

lore
Share & tools
lore
#0 lore raw

PATCH 3/3 hwmon: (smsc47m1) Enable device if needed

If the address is set but the device isn't enabled, attempt to enable it. If it won't work for any reason (resource conflict, no function enabled) the initial state is restored. The initial state is also restored on module unloading.

---
 drivers/hwmon/smsc47m1.c |   30 +++++++++++++++++++++++++++---
 1 file changed, 27 insertions(+), 3 deletions(-)
drivers/hwmon/smsc47m1.c +27 -3
@@ -136,6 +136,7 @@ struct smsc47m1_data {
 
 struct smsc47m1_sio_data {
 	enum chips type;
+	u8 activate;		/* Remember initial device state */
 };
 
 
@@ -468,17 +469,38 @@ static int __init smsc47m1_find(unsigned
 	superio_select();
 	*addr = (superio_inb(SUPERIO_REG_BASE) << 8)
 	      |  superio_inb(SUPERIO_REG_BASE + 1);
-	val = superio_inb(SUPERIO_REG_ACT);
-	if (*addr = 0 || (val & 0x01) = 0) {
-		pr_info(DRVNAME ": Device is disabled, will not use\n");
+	if (*addr = 0) {
+		pr_info(DRVNAME ": Device address not set, will not use\n");
 		superio_exit();
 		return -ENODEV;
 	}
 
+	/* Enable only if address is set (needed at least on the
+	 * Compaq Presario S4000NX) */
+	sio_data->activate = superio_inb(SUPERIO_REG_ACT);
+	if ((sio_data->activate & 0x01) = 0) {
+		pr_info(DRVNAME ": Enabling device\n");
+		superio_outb(SUPERIO_REG_ACT, sio_data->activate | 0x01);
+	}
+
 	superio_exit();
 	return 0;
 }
 
+/* Restore device to its initial state */
+static void __init smsc47m1_restore(const struct smsc47m1_sio_data *sio_data)
+{
+	if ((sio_data->activate & 0x01) = 0) {
+		superio_enter();
+		superio_select();
+
+		pr_info(DRVNAME ": Disabling device\n");
+		superio_outb(SUPERIO_REG_ACT, sio_data->activate);
+
+		superio_exit();
+	}
+}
+
 #define CHECK		1
 #define REQUEST		2
 #define RELEASE		3
@@ -856,6 +878,7 @@ static int __init sm_smsc47m1_init(void)
 
 exit_device:
 	platform_device_unregister(pdev);
+	smsc47m1_restore(&sio_data);
 exit:
 	return err;
 }
@@ -863,6 +886,7 @@ exit:
 static void __exit sm_smsc47m1_exit(void)
 {
 	platform_driver_unregister(&smsc47m1_driver);
+	smsc47m1_restore(pdev->dev.platform_data);
 	platform_device_unregister(pdev);
 }
 
Signature · 6 lines
Jean Delvare

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors