OMAP2xxx clock/CPUFreq: fix compilation errors; clean up

index d0e3fb7..ce6742f 100644
@@ -455,12 +455,15 @@ static struct cpufreq_frequency_table freq_table[ARRAY_SIZE(rate_table)];
 void omap2_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
 {
 	struct prcm_config *prcm;
+	long sys_ck_rate;
 	int i = 0;
 
+	sys_ck_rate = clk_get_rate(sclk);
+
 	for (prcm = rate_table; prcm->mpu_speed; prcm++) {
 		if (!(prcm->flags & cpu_mask))
 			continue;
-		if (prcm->xtal_speed != sys_ck.rate)
+		if (prcm->xtal_speed != sys_ck_rate)
 			continue;
 
 		/* don't put bypass rates in table */

index 126a939..e6dda69 100644
@@ -9,45 +9,47 @@
  * The OMAP2 processor can be run at several discrete 'PRCM configurations'.
  * These configurations are characterized by voltage and speed for clocks.
  * The device is only validated for certain combinations. One way to express
- * these combinations is via the 'ratio's' which the clocks operate with
+ * these combinations is via the 'ratios' which the clocks operate with
  * respect to each other. These ratio sets are for a given voltage/DPLL
- * setting. All configurations can be described by a DPLL setting and a ratio
- * There are 3 ratio sets for the 2430 and X ratio sets for 2420.
- *
- * 2430 differs from 2420 in that there are no more phase synchronizers used.
- * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
- * 2430 (iva2.1, NOdsp, mdm)
+ * setting. All configurations can be described by a DPLL setting and a ratio.
  *
  * XXX Missing voltage data.
+ * XXX Missing 19.2MHz sys_clk rate sets (needed for N800/N810)
  *
  * THe format described in this file is deprecated.  Once a reasonable
  * OPP API exists, the data in this file should be converted to use it.
  *
  * This is technically part of the OMAP2xxx clock code.
+ *
+ * Considerable work is still needed to fully support dynamic frequency
+ * changes on OMAP2xxx-series chips.  Readers interested in such a
+ * project are encouraged to review the Maemo Diablo RX-34 and RX-44
+ * kernel source at:
+ *     http://repository.maemo.org/pool/diablo/free/k/kernel-source-diablo/
  */
 
 #include "opp2xxx.h"
 #include "sdrc.h"
 #include "clock.h"
 
-/*-------------------------------------------------------------------------
- * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated.
+/*
+ * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated.
  * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,
  * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL,
  * CM_CLKSEL2_PLL, CM_CLKSEL_MDM
  *
- * Filling in table based on H4 boards and 2430-SDPs variants available.
- * There are quite a few more rates combinations which could be defined.
+ * Filling in table based on H4 boards available.  There are quite a
+ * few more rate combinations which could be defined.
  *
- * When multiple values are defined the start up will try and choose the
- * fastest one. If a 'fast' value is defined, then automatically, the /2
- * one should be included as it can be used.	Generally having more that
- * one fast set does not make sense, as static timings need to be changed
- * to change the set.	 The exception is the bypass setting which is
- * availble for low power bypass.
+ * When multiple values are defined the start up will try and choose
+ * the fastest one. If a 'fast' value is defined, then automatically,
+ * the /2 one should be included as it can be used.  Generally having
+ * more than one fast set does not make sense, as static timings need
+ * to be changed to change the set.  The exception is the bypass
+ * setting which is available for low power bypass.
  *
  * Note: This table needs to be sorted, fastest to slowest.
- *-------------------------------------------------------------------------*/
+ **/
 const struct prcm_config omap2420_rate_table[] = {
 	/* PRCM I - FAST */
 	{S12M, S660M, S330M, RI_CM_CLKSEL_MPU_VAL,		/* 330MHz ARM */

index edb8167..1b9596a 100644
@@ -1,5 +1,5 @@
 /*
- * opp2420_data.c - old-style "OPP" table for OMAP2420
+ * opp2430_data.c - old-style "OPP" table for OMAP2430
  *
  * Copyright (C) 2005-2009 Texas Instruments, Inc.
  * Copyright (C) 2004-2009 Nokia Corporation

@@ -9,16 +9,16 @@
  * The OMAP2 processor can be run at several discrete 'PRCM configurations'.
  * These configurations are characterized by voltage and speed for clocks.
  * The device is only validated for certain combinations. One way to express
- * these combinations is via the 'ratio's' which the clocks operate with
+ * these combinations is via the 'ratios' which the clocks operate with
  * respect to each other. These ratio sets are for a given voltage/DPLL
- * setting. All configurations can be described by a DPLL setting and a ratio
- * There are 3 ratio sets for the 2430 and X ratio sets for 2420.
+ * setting. All configurations can be described by a DPLL setting and a ratio.
  *
  * 2430 differs from 2420 in that there are no more phase synchronizers used.
  * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
  * 2430 (iva2.1, NOdsp, mdm)
  *
  * XXX Missing voltage data.
+ * XXX Missing 19.2MHz sys_clk rate sets.
  *
  * THe format described in this file is deprecated.  Once a reasonable
  * OPP API exists, the data in this file should be converted to use it.

@@ -30,24 +30,24 @@
 #include "sdrc.h"
 #include "clock.h"
 
-/*-------------------------------------------------------------------------
- * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated.
+/*
+ * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated.
  * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,
  * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL,
  * CM_CLKSEL2_PLL, CM_CLKSEL_MDM
  *
- * Filling in table based on H4 boards and 2430-SDPs variants available.
- * There are quite a few more rates combinations which could be defined.
+ * Filling in table based on 2430-SDPs variants available.  There are
+ * quite a few more rate combinations which could be defined.
  *
- * When multiple values are defined the start up will try and choose the
- * fastest one. If a 'fast' value is defined, then automatically, the /2
- * one should be included as it can be used.	Generally having more that
- * one fast set does not make sense, as static timings need to be changed
- * to change the set.	 The exception is the bypass setting which is
- * availble for low power bypass.
+ * When multiple values are defined the start up will try and choose
+ * the fastest one. If a 'fast' value is defined, then automatically,
+ * the /2 one should be included as it can be used.  Generally having
+ * more than one fast set does not make sense, as static timings need
+ * to be changed to change the set.  The exception is the bypass
+ * setting which is available for low power bypass.
  *
  * Note: This table needs to be sorted, fastest to slowest.
- *-------------------------------------------------------------------------*/
+ */
 const struct prcm_config omap2430_rate_table[] = {
 	/* PRCM #4 - ratio2 (ES2.1) - FAST */
 	{S13M, S798M, S399M, R2_CM_CLKSEL_MPU_VAL,		/* 399MHz ARM */

index ce6742f..3bfd045 100644
@@ -449,14 +449,16 @@ int omap2_select_table_rate(struct clk *clk, unsigned long rate)
 #ifdef CONFIG_CPU_FREQ
 /*
  * Walk PRCM rate table and fillout cpufreq freq_table
+ * XXX This should be replaced by an OPP layer in the near future
  */
-static struct cpufreq_frequency_table freq_table[ARRAY_SIZE(rate_table)];
+static struct cpufreq_frequency_table *freq_table;
 
 void omap2_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
 {
-	struct prcm_config *prcm;
+	const struct prcm_config *prcm;
 	long sys_ck_rate;
 	int i = 0;
+	int tbl_sz = 0;
 
 	sys_ck_rate = clk_get_rate(sclk);
 

@@ -470,17 +472,44 @@ void omap2_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
 		if (prcm->dpll_speed == prcm->xtal_speed)
 			continue;
 
-		freq_table[i].index = i;
-		freq_table[i].frequency = prcm->mpu_speed / 1000;
-		i++;
+		tbl_sz++;
 	}
 
-	if (i == 0) {
-		printk(KERN_WARNING "%s: failed to initialize frequency "
-		       "table\n", __func__);
+	/*
+	 * XXX Ensure that we're doing what CPUFreq expects for this error
+	 * case and the following one
+	 */
+	if (tbl_sz == 0) {
+		pr_warning("%s: no matching entries in rate_table\n",
+			   __func__);
 		return;
 	}
 
+	/* Include the CPUFREQ_TABLE_END terminator entry */
+	tbl_sz++;
+
+	freq_table = kzalloc(sizeof(struct cpufreq_frequency_table) * tbl_sz,
+			     GFP_KERNEL);
+	if (!freq_table) {
+		pr_err("%s: could not kzalloc frequency table\n", __func__);
+		return;
+	}
+
+	for (prcm = rate_table; prcm->mpu_speed; prcm++) {
+		if (!(prcm->flags & cpu_mask))
+			continue;
+		if (prcm->xtal_speed != sys_ck_rate)
+			continue;
+
+		/* don't put bypass rates in table */
+		if (prcm->dpll_speed == prcm->xtal_speed)
+			continue;
+
+		freq_table[i].index = i;
+		freq_table[i].frequency = prcm->mpu_speed / 1000;
+		i++;
+	}
+
 	freq_table[i].index = i;
 	freq_table[i].frequency = CPUFREQ_TABLE_END;
 

index 3bfd045..74f5586 100644
@@ -515,6 +515,12 @@ void omap2_clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
 
 	*table = &freq_table[0];
 }
+
+void omap2_clk_exit_cpufreq_table(struct cpufreq_frequency_table **table)
+{
+	kfree(freq_table);
+}
+
 #endif
 
 struct clk_functions omap2_clk_functions = {

@@ -526,6 +532,7 @@ struct clk_functions omap2_clk_functions = {
 	.clk_disable_unused	= omap2_clk_disable_unused,
 #ifdef	CONFIG_CPU_FREQ
 	.clk_init_cpufreq_table	= omap2_clk_init_cpufreq_table,
+	.clk_exit_cpufreq_table	= omap2_clk_exit_cpufreq_table,
 #endif
 };
 

index a64d84c..d9f8c84 100644
@@ -329,6 +329,16 @@ void clk_init_cpufreq_table(struct cpufreq_frequency_table **table)
 		arch_clock->clk_init_cpufreq_table(table);
 	spin_unlock_irqrestore(&clockfw_lock, flags);
 }
+
+void clk_exit_cpufreq_table(struct cpufreq_frequency_table **table)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&clockfw_lock, flags);
+	if (arch_clock->clk_exit_cpufreq_table)
+		arch_clock->clk_exit_cpufreq_table(table);
+	spin_unlock_irqrestore(&clockfw_lock, flags);
+}
 #endif
 
 /*-------------------------------------------------------------------------*/

index f8ddbdd..6d3d333 100644
@@ -134,6 +134,7 @@ static int __init omap_cpu_init(struct cpufreq_policy *policy)
 
 static int omap_cpu_exit(struct cpufreq_policy *policy)
 {
+	clk_exit_cpufreq_table(&freq_table);
 	clk_put(mpu_clk);
 	return 0;
 }

index 309b6d1..94fe2a0 100644
@@ -119,6 +119,7 @@ struct clk_functions {
 	void		(*clk_disable_unused)(struct clk *clk);
 #ifdef CONFIG_CPU_FREQ
 	void		(*clk_init_cpufreq_table)(struct cpufreq_frequency_table **);
+	void		(*clk_exit_cpufreq_table)(struct cpufreq_frequency_table **);
 #endif
 };
 

@@ -135,6 +136,7 @@ extern unsigned long followparent_recalc(struct clk *clk);
 extern void clk_enable_init_clocks(void);
 #ifdef CONFIG_CPU_FREQ
 extern void clk_init_cpufreq_table(struct cpufreq_frequency_table **table);
+extern void clk_exit_cpufreq_table(struct cpufreq_frequency_table **table);
 #endif
 
 extern const struct clkops clkops_null;