BAR 0: can't allocate resource
Hi,
I have a problem getting a couple of PCI cards to play nicely together. The error I get (in dmesg) is:
2.6.26 kernel:
[ 0.215619] PCI: Cannot allocate resource region 0 of device 0000:01:04.0 2.6.30 kernel: [ 0.138390] pci 0000:01:04.0: BAR 0: can't allocate resource
And (for both kernels) the output of lspci has the following line:
01:04.0 Unclassified device [0080]: Device 0002:0080
Hardware Details:
- My motherboard is a DigitalLogic MSM945. It has a PC104 bus.
- I have two PC104 cards:
i) 8-port serial card (DiamondSystems Emerald-MM-8Plus)
ii) PC/104+ to MiniPCI Adapter (ConnectTech) (no MiniPCI cards installed).
(I have run both of these cards with a different motherboard, no problems).
I've compared two conditions:
a) "working": serial card installed by itself, and
b) "broken": serial + MiniPCI cards both installed
For the 2.6.26 kernel, I've attached the output of
- dmesg
- lspci
- lspci -v
- cat /proc/iomem
for both 'working' and 'broken' cases.
(Note: in both cases the following two lines appear in the dmesg output:
[ 0.185656] PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard resources [ 0.185711] PCI: Not using MMCONFIG
Is this significant?)
Does anyone have any ideas what to try here? I've been fighting with this for a while now...
(Please Cc me on any response).
Thanks,
Alex
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7c0000 (usable) [ 0.000000] BIOS-e820: 000000003f7c0000 - 000000003f7ce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003f7ce000 - 000000003f800000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) [ 0.000000] 119MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 [ 0.000000] Entering add_active_range(0, 0, 260032) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 260032 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 260032 [ 0.000000] On node 0 totalpages: 260032 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 240 pages used for memmap [ 0.000000] HighMem zone: 30416 pages, LIFO batch:7 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F8ED0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 3F7C0000, 003C (r1 112007 RSDT1407 20071120 MSFT 97) [ 0.000000] ACPI: FACP 3F7C0200, 0084 (r2 112007 FACP1407 20071120 MSFT 97) [ 0.000000] ACPI: DSDT 3F7C05B0, 4FF8 (r1 DLAG_ DLAG_117 117 INTL 20051117) [ 0.000000] ACPI: FACS 3F7CE000, 0040 [ 0.000000] ACPI: APIC 3F7C0390, 005C (r1 112007 APIC1407 20071120 MSFT 97) [ 0.000000] ACPI: MCFG 3F7C03F0, 003C (r1 112007 OEMMCFG 20071120 MSFT 97) [ 0.000000] ACPI: SLIC 3F7C0430, 0176 (r1 112007 SLIC1407 20071120 MSFT 97) [ 0.000000] ACPI: OEMB 3F7CE040, 0071 (r1 112007 OEMB1407 20071120 MSFT 97) [ 0.000000] ACPI: ASF! 3F7C55B0, 0075 (r32 LEGEND I865PASF 1 INTL 20051117) [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:bf600000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs [ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258000 [ 0.000000] Kernel command line: root=/dev/hdb2 ro 8250.nr_uarts=10 quiet [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1666.659 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.004000] Memory: 1021100k/1040128k available (1770k kernel code, 18312k reserved, 750k data, 244k init, 122624k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) [ 0.004000] .data : 0xc02baaa1 - 0xc0376620 ( 750 kB) [ 0.004000] .text : 0xc0100000 - 0xc02baaa1 (1770 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.084099] Calibrating delay using timer specific routine.. 3337.13 BogoMIPS (lpj=6674263) [ 0.084138] Security Framework initialized [ 0.084144] SELinux: Disabled at boot. [ 0.084149] Capability LSM initialized [ 0.084164] Mount-cache hash table entries: 512 [ 0.084310] Initializing cgroup subsys ns [ 0.084314] Initializing cgroup subsys cpuacct [ 0.084317] Initializing cgroup subsys devices [ 0.084335] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.084339] CPU: L2 cache: 2048K [ 0.084343] Intel machine check architecture supported. [ 0.084349] Intel machine check reporting enabled on CPU#0. [ 0.084351] using mwait in idle threads. [ 0.084360] Checking 'hlt' instruction... OK. [ 0.100419] SMP alternatives: switching to UP code [ 0.106246] ACPI: Core revision 20080321 [ 0.120007] ENABLING IO-APIC IRQs [ 0.120007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.160010] CPU0: Intel(R) Core(TM) Duo CPU L2400 @ 1.66GHz stepping 0c [ 0.160010] Brought up 1 CPUs [ 0.160010] Total of 1 processors activated (3337.13 BogoMIPS). [ 0.160010] CPU0 attaching sched-domain: [ 0.160010] domain 0: span 0 [ 0.160010] groups: 0 [ 0.160010] net_namespace: 660 bytes [ 0.160010] Booting paravirtualized kernel on bare hardware [ 0.160010] NET: Registered protocol family 16 [ 0.160010] ACPI: bus type pci registered [ 0.160010] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.160010] PCI: Not using MMCONFIG. [ 0.160010] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1 [ 0.160010] PCI: Using configuration type 1 for base access [ 0.160010] Setting up standard PCI resources [ 0.168010] ACPI: EC: Look up EC in DSDT [ 0.178065] ACPI: Interpreter enabled [ 0.178068] ACPI: (supports S0 S1 S3 S4 S5) [ 0.178085] ACPI: Using IOAPIC for interrupt routing [ 0.178152] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.185649] PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard resources [ 0.185704] PCI: Not using MMCONFIG. [ 0.195968] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.196647] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.196654] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.196659] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.197033] PCI: Transparent bridge - 0000:00:1e.0 [ 0.197057] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.197315] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.207497] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.207646] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.207793] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.207939] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.208013] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.208160] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.208309] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.208454] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15) [ 0.208673] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 48, should be 41 [20080321] [ 0.208698] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.208729] pnp: PnP ACPI init [ 0.208738] ACPI: bus type pnp registered [ 0.215303] pnp: PnP ACPI: found 17 devices [ 0.215306] ACPI: ACPI bus type pnp unregistered [ 0.215310] PnPBIOS: Disabled by ACPI PNP [ 0.215562] PCI: Using ACPI for IRQ routing [ 0.215619] PCI: Cannot allocate resource region 0 of device 0000:01:04.0 [ 0.215890] hpet clockevent registered [ 0.215897] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.215902] hpet0: 3 64-bit timers, 14318180 Hz [ 0.216944] ACPI: RTC can wake from S4 [ 0.216970] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved [ 0.216980] system 00:09: ioport range 0xa00-0xa0f has been reserved [ 0.216990] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved [ 0.216993] system 00:0b: ioport range 0x800-0x87f has been reserved [ 0.216996] system 00:0b: ioport range 0x480-0x4bf has been reserved [ 0.217000] system 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.217003] system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.217006] system 00:0b: iomem range 0xfed40000-0xfed8ffff has been reserved [ 0.217013] system 00:0d: iomem range 0xffc00000-0xffefffff could not be reserved [ 0.217020] system 00:0e: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.217023] system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved [ 0.217029] system 00:0f: iomem range 0xe0000000-0xe3ffffff has been reserved [ 0.217036] system 00:10: iomem range 0x0-0x9ffff could not be reserved [ 0.217039] system 00:10: iomem range 0xc0000-0xcffff could not be reserved [ 0.217042] system 00:10: iomem range 0xe0000-0xfffff could not be reserved [ 0.217045] system 00:10: iomem range 0x100000-0x3f7fffff could not be reserved [ 0.217049] system 00:10: iomem range 0xfed90000-0xffffffff could not be reserved [ 0.247436] PCI: Error while updating region 0000:01:04.0/0 (feb00002 != 00000000) [ 0.247489] PCI: Bridge: 0000:00:1e.0 [ 0.247493] IO window: e000-efff [ 0.247498] MEM window: 0xfeb00000-0xfebfffff [ 0.247503] PREFETCH window: disabled. [ 0.247520] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.247539] NET: Registered protocol family 2 [ 0.247628] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.247859] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.248652] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.249054] TCP: Hash tables configured (established 131072 bind 65536) [ 0.249057] TCP reno registered [ 0.249169] NET: Registered protocol family 1 [ 0.249290] checking if image is initramfs... it is [ 0.716035] Switched to high resolution mode on CPU 0 [ 0.818306] Freeing initrd memory: 6040k freed [ 0.819062] audit: initializing netlink socket (disabled) [ 0.819079] type=2000 audit(1262505979.816:1): initialized [ 0.819232] highmem bounce pool size: 64 pages [ 0.819237] Total HugeTLB memory allocated, 0 [ 0.819310] VFS: Disk quotas dquot_6.5.1 [ 0.819339] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.819384] msgmni has been set to 1767 [ 0.819489] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.819494] io scheduler noop registered [ 0.819496] io scheduler anticipatory registered [ 0.819498] io scheduler deadline registered [ 0.819509] io scheduler cfq registered (default) [ 0.819523] pci 0000:00:02.0: Boot video device [ 0.819621] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling [ 0.819941] isapnp: Scanning for PnP cards... [ 1.174338] isapnp: No Plug & Play device found [ 1.176903] Serial: 8250/16550 driver $Revision: 1.90 $ 10 ports, IRQ sharing enabled [ 1.177037] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.177166] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 1.177801] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.177984] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 1.179441] brd: module loaded [ 1.179592] PNP: No PS/2 controller found. Probing ports directly. [ 1.181887] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.181892] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.182034] mice: PS/2 mouse device common for all mice [ 1.182159] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.182179] rtc0: alarms up to one month [ 1.182214] cpuidle: using governor ladder [ 1.182217] cpuidle: using governor menu [ 1.182222] No iBFT detected. [ 1.182637] TCP cubic registered [ 1.182640] NET: Registered protocol family 17 [ 1.182646] Using IPI No-Shortcut mode [ 1.182758] registered taskstats version 1 [ 1.182889] rtc_cmos 00:03: setting system clock to 2010-01-03 08:06:20 UTC (1262505980) [ 1.183018] Freeing unused kernel memory: 244k freed [ 1.272162] ACPI: SSDT 3F7CE0C0, 0688 (r1 AMI CPU1PM 1 INTL 20051117) [ 1.272769] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 1.272814] ACPI: ACPI0007:00 is registered as cooling_device0 [ 1.723884] usbcore: registered new interface driver usbfs [ 1.723912] usbcore: registered new interface driver hub [ 1.723944] usbcore: registered new device driver usb [ 1.732059] USB Universal Host Controller Interface driver v3.0 [ 1.732108] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 [ 1.732119] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 1.732123] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 1.732248] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 1.732283] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000dc00 [ 1.732367] usb usb1: configuration #1 chosen from 1 choice [ 1.732399] hub 1-0:1.0: USB hub found [ 1.732406] hub 1-0:1.0: 2 ports detected [ 1.835739] Uniform Multi-Platform E-IDE driver [ 1.835745] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 1.836125] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.836129] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.836132] usb usb1: Product: UHCI Host Controller [ 1.836134] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 1.836136] usb usb1: SerialNumber: 0000:00:1d.0 [ 1.836205] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 1.836217] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 1.836221] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 1.836247] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 1.836280] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880 [ 1.836355] usb usb2: configuration #1 chosen from 1 choice [ 1.836384] hub 2-0:1.0: USB hub found [ 1.836392] hub 2-0:1.0: 2 ports detected [ 1.850586] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI [ 1.850589] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.940109] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.940113] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.940116] usb usb2: Product: UHCI Host Controller [ 1.940118] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 1.940121] usb usb2: SerialNumber: 0000:00:1d.1 [ 1.940171] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 1.940182] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 1.940187] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 1.940218] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 1.940251] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800 [ 1.940329] usb usb3: configuration #1 chosen from 1 choice [ 1.940357] hub 3-0:1.0: USB hub found [ 1.940363] hub 3-0:1.0: 2 ports detected [ 1.990370] Marking TSC unstable due to: TSC halts in idle. [ 2.044104] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.044107] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.044110] usb usb3: Product: UHCI Host Controller [ 2.044113] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 2.044115] usb usb3: SerialNumber: 0000:00:1d.2 [ 2.044166] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16 [ 2.044175] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 2.044179] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.044201] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 2.044233] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d480 [ 2.044306] usb usb4: configuration #1 chosen from 1 choice [ 2.044335] hub 4-0:1.0: USB hub found [ 2.044341] hub 4-0:1.0: 2 ports detected [ 2.076027] usb 1-2: new low speed USB device using uhci_hcd and address 2 [ 2.148091] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.148094] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.148097] usb usb4: Product: UHCI Host Controller [ 2.148099] usb usb4: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 2.148102] usb usb4: SerialNumber: 0000:00:1d.3 [ 2.148231] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 [ 2.148247] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 2.148251] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.148275] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 2.152182] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.152190] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 2.152195] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfea37c00 [ 2.212025] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 2.212081] usb usb5: configuration #1 chosen from 1 choice [ 2.212108] hub 5-0:1.0: USB hub found [ 2.212114] hub 5-0:1.0: 8 ports detected [ 2.316093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.316096] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.316099] usb usb5: Product: EHCI Host Controller [ 2.316101] usb usb5: Manufacturer: Linux 2.6.26-2-686 ehci_hcd [ 2.316104] usb usb5: SerialNumber: 0000:00:1d.7 [ 2.318728] No dock devices found. [ 2.326910] SCSI subsystem initialized [ 2.336011] libata version 3.00 loaded. [ 2.336998] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 2.363103] e100: eth0: e100_probe: addr 0xfebfe000, irq 20, MAC addr 00:30:59:04:25:2e [ 2.365334] ata_piix 0000:00:1f.2: version 2.12 [ 2.365351] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 2.365356] ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] [ 2.365391] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 2.365442] scsi0 : ata_piix [ 2.365517] scsi1 : ata_piix [ 2.365547] ata1: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xcc00 irq 19 [ 2.365550] ata2: SATA max UDMA/133 cmd 0xd000 ctl 0xcc80 bmdma 0xcc08 irq 19 [ 2.608024] usb 1-2: device not accepting address 2, error -71 [ 2.664047] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2.695202] ICH7: IDE controller (0x8086:0x27df rev 0x02) at PCI slot 0000:00:1f.1 [ 2.695214] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 2.695224] ICH7: not 100% native mode: will probe irqs later [ 2.695233] ICH7: IDE port disabled [ 2.695240] ide0: BM-DMA at 0xffa0-0xffa7 [ 2.695247] Probing IDE interface ide0... [ 3.120330] usb 1-2: new low speed USB device using uhci_hcd and address 4 [ 3.208387] hdb: SILICONSYSTEMS UDMA 4GB-4300, ATA DISK drive [ 3.264062] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 3.264109] hdb: host side 80-wire cable detection failed, limiting max speed to UDMA33 [ 3.264112] hdb: UDMA/33 mode selected [ 3.264163] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 3.279613] hdb: max request size: 128KiB [ 3.279617] hdb: 8027712 sectors (4110 MB) w/1KiB Cache, CHS=7964/16/63 [ 3.279896] hdb: cache flushes supported [ 3.279930] hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 hdb7 hdb8 hdb9 > [ 3.372380] usb 1-2: configuration #1 chosen from 1 choice [ 3.373684] PM: Starting manual resume from disk [ 3.378477] usb 1-2: New USB device found, idVendor=1241, idProduct=1603 [ 3.378481] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.378484] usb 1-2: Product: USB Keyboard [ 3.378486] usb 1-2: Manufacturer: [ 3.414683] usbcore: registered new interface driver hiddev [ 3.417555] kjournald starting. Commit interval 5 seconds [ 3.417566] EXT3-fs: mounted filesystem with ordered data mode. [ 3.458143] input: USB Keyboard as /class/input/input0 [ 3.458143] input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.0-2 [ 3.543382] input: USB Keyboard as /class/input/input1 [ 3.552031] input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.0-2 [ 3.552051] usbcore: registered new interface driver usbhid [ 3.552055] usbhid: v2.6:USB HID core driver [ 3.773202] udevd version 125 started [ 4.366743] Linux agpgart interface v0.103 [ 4.375872] agpgart: Detected an Intel 945GME Chipset. [ 4.376229] agpgart: Detected 7932K stolen memory. [ 4.391529] agpgart: AGP aperture is 256M @ 0xd0000000 [ 4.563115] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 4.563135] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 4.593853] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... [ 4.595122] input: Power Button (FF) as /class/input/input2 [ 4.624054] ACPI: Power Button (FF) [PWRF] [ 4.624148] input: Power Button (CM) as /class/input/input3 [ 4.652044] ACPI: Power Button (CM) [PWRB] [ 5.670043] intel_rng: FWH not detected [ 5.734423] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 5.734496] iTCO_wdt: Found a ICH7-M DH TCO device (Version=2, TCOBASE=0x0860) [ 5.734524] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 5.740578] input: Video Bus as /class/input/input4 [ 5.772049] ACPI: Video Device [IGD] (multi-head: yes rom: no post: no) [ 5.901055] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19 [ 6.011232] input: PC Speaker as /class/input/input5 [ 6.048672] Error: Driver 'pcspkr' is already registered, aborting... [ 6.299792] parport_pc 00:08: reported by Plug and Play ACPI [ 6.299845] parport0: PC-style at 0x378, irq 7 [PCSPP] [ 6.974349] Adding 489940k swap on /dev/hdb8. Priority:-1 extents:1 across:489940k [ 7.847947] loop: module loaded [ 7.861361] ppdev: user-space parallel port driver [ 8.218580] kjournald starting. Commit interval 5 seconds [ 8.218589] EXT3-fs: mounted filesystem with ordered data mode. [ 8.219908] kjournald starting. Commit interval 5 seconds [ 8.242677] EXT3 FS on hdb6, internal journal [ 8.242681] EXT3-fs: mounted filesystem with ordered data mode. [ 8.243566] kjournald starting. Commit interval 5 seconds [ 8.285475] EXT3 FS on hdb7, internal journal [ 8.285475] EXT3-fs: mounted filesystem with ordered data mode. [ 8.286626] kjournald starting. Commit interval 5 seconds [ 8.286626] EXT3-fs: mounted filesystem with ordered data mode. [ 8.287131] kjournald starting. Commit interval 5 seconds [ 8.302911] EXT3 FS on hdb5, internal journal [ 8.302911] EXT3-fs: mounted filesystem with ordered data mode. [ 9.346890] NET: Registered protocol family 10 [ 9.347300] lo: Disabled Privacy Extensions [ 9.424398] warning: `ntpd' uses 32-bit capabilities (legacy support in use) [ 96.685169] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 96.688130] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex [ 96.688492] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 107.232020] eth0: no IPv6 routers present [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) ([email protected]) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7c0000 (usable) [ 0.000000] BIOS-e820: 000000003f7c0000 - 000000003f7ce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003f7ce000 - 000000003f800000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) [ 0.000000] 119MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 [ 0.000000] Entering add_active_range(0, 0, 260032) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 260032 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 260032 [ 0.000000] On node 0 totalpages: 260032 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 240 pages used for memmap [ 0.000000] HighMem zone: 30416 pages, LIFO batch:7 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F8ED0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 3F7C0000, 003C (r1 112007 RSDT1407 20071120 MSFT 97) [ 0.000000] ACPI: FACP 3F7C0200, 0084 (r2 112007 FACP1407 20071120 MSFT 97) [ 0.000000] ACPI: DSDT 3F7C05B0, 4FF8 (r1 DLAG_ DLAG_117 117 INTL 20051117) [ 0.000000] ACPI: FACS 3F7CE000, 0040 [ 0.000000] ACPI: APIC 3F7C0390, 005C (r1 112007 APIC1407 20071120 MSFT 97) [ 0.000000] ACPI: MCFG 3F7C03F0, 003C (r1 112007 OEMMCFG 20071120 MSFT 97) [ 0.000000] ACPI: SLIC 3F7C0430, 0176 (r1 112007 SLIC1407 20071120 MSFT 97) [ 0.000000] ACPI: OEMB 3F7CE040, 0071 (r1 112007 OEMB1407 20071120 MSFT 97) [ 0.000000] ACPI: ASF! 3F7C55B0, 0075 (r32 LEGEND I865PASF 1 INTL 20051117) [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:bf600000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs [ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258000 [ 0.000000] Kernel command line: root=/dev/hdb2 ro 8250.nr_uarts=10 quiet [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1666.746 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.004000] Memory: 1021100k/1040128k available (1770k kernel code, 18312k reserved, 750k data, 244k init, 122624k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) [ 0.004000] .data : 0xc02baaa1 - 0xc0376620 ( 750 kB) [ 0.004000] .text : 0xc0100000 - 0xc02baaa1 (1770 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.084100] Calibrating delay using timer specific routine.. 3337.12 BogoMIPS (lpj=6674246) [ 0.084138] Security Framework initialized [ 0.084144] SELinux: Disabled at boot. [ 0.084148] Capability LSM initialized [ 0.084165] Mount-cache hash table entries: 512 [ 0.084306] Initializing cgroup subsys ns [ 0.084312] Initializing cgroup subsys cpuacct [ 0.084315] Initializing cgroup subsys devices [ 0.084333] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.084337] CPU: L2 cache: 2048K [ 0.084341] Intel machine check architecture supported. [ 0.084347] Intel machine check reporting enabled on CPU#0. [ 0.084350] using mwait in idle threads. [ 0.084358] Checking 'hlt' instruction... OK. [ 0.100420] SMP alternatives: switching to UP code [ 0.106268] ACPI: Core revision 20080321 [ 0.120007] ENABLING IO-APIC IRQs [ 0.120007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.159714] CPU0: Intel(R) Core(TM) Duo CPU L2400 @ 1.66GHz stepping 0c [ 0.160010] Brought up 1 CPUs [ 0.160010] Total of 1 processors activated (3337.12 BogoMIPS). [ 0.160010] CPU0 attaching sched-domain: [ 0.160010] domain 0: span 0 [ 0.160010] groups: 0 [ 0.160010] net_namespace: 660 bytes [ 0.160010] Booting paravirtualized kernel on bare hardware [ 0.160010] NET: Registered protocol family 16 [ 0.160010] ACPI: bus type pci registered [ 0.160010] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.160010] PCI: Not using MMCONFIG. [ 0.160010] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1 [ 0.160010] PCI: Using configuration type 1 for base access [ 0.160010] Setting up standard PCI resources [ 0.168010] ACPI: EC: Look up EC in DSDT [ 0.178097] ACPI: Interpreter enabled [ 0.178100] ACPI: (supports S0 S1 S3 S4 S5) [ 0.178117] ACPI: Using IOAPIC for interrupt routing [ 0.178184] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.185656] PCI: BIOS Bug: MCFG area at e0000000 is not reserved in ACPI motherboard resources [ 0.185711] PCI: Not using MMCONFIG. [ 0.195955] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.196636] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.196642] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.196647] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.197010] PCI: Transparent bridge - 0000:00:1e.0 [ 0.197035] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.197293] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.207476] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.207624] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.207770] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.207914] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.208013] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 *15) [ 0.208013] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.208162] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.208307] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15) [ 0.208521] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 48, should be 41 [20080321] [ 0.208545] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.208576] pnp: PnP ACPI init [ 0.208584] ACPI: bus type pnp registered [ 0.215142] pnp: PnP ACPI: found 17 devices [ 0.215145] ACPI: ACPI bus type pnp unregistered [ 0.215149] PnPBIOS: Disabled by ACPI PNP [ 0.215400] PCI: Using ACPI for IRQ routing [ 0.215677] hpet clockevent registered [ 0.215683] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.215688] hpet0: 3 64-bit timers, 14318180 Hz [ 0.216731] ACPI: RTC can wake from S4 [ 0.216758] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved [ 0.216768] system 00:09: ioport range 0xa00-0xa0f has been reserved [ 0.216777] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved [ 0.216781] system 00:0b: ioport range 0x800-0x87f has been reserved [ 0.216784] system 00:0b: ioport range 0x480-0x4bf has been reserved [ 0.216787] system 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.216791] system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.216794] system 00:0b: iomem range 0xfed40000-0xfed8ffff has been reserved [ 0.216801] system 00:0d: iomem range 0xffc00000-0xffefffff could not be reserved [ 0.216807] system 00:0e: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.216811] system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved [ 0.216817] system 00:0f: iomem range 0xe0000000-0xe3ffffff has been reserved [ 0.216823] system 00:10: iomem range 0x0-0x9ffff could not be reserved [ 0.216827] system 00:10: iomem range 0xc0000-0xcffff could not be reserved [ 0.216830] system 00:10: iomem range 0xe0000-0xfffff could not be reserved [ 0.216833] system 00:10: iomem range 0x100000-0x3f7fffff could not be reserved [ 0.216837] system 00:10: iomem range 0xfed90000-0xffffffff could not be reserved [ 0.247235] PCI: Bridge: 0000:00:1e.0 [ 0.247239] IO window: e000-efff [ 0.247245] MEM window: 0xfeb00000-0xfebfffff [ 0.247249] PREFETCH window: disabled. [ 0.247267] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.247288] NET: Registered protocol family 2 [ 0.247378] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.247612] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.248410] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.248809] TCP: Hash tables configured (established 131072 bind 65536) [ 0.248814] TCP reno registered [ 0.248924] NET: Registered protocol family 1 [ 0.249046] checking if image is initramfs... it is [ 0.716009] Switched to high resolution mode on CPU 0 [ 0.817665] Freeing initrd memory: 6040k freed [ 0.818424] audit: initializing netlink socket (disabled) [ 0.818440] type=2000 audit(1262506709.816:1): initialized [ 0.818596] highmem bounce pool size: 64 pages [ 0.818601] Total HugeTLB memory allocated, 0 [ 0.818674] VFS: Disk quotas dquot_6.5.1 [ 0.818702] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.818747] msgmni has been set to 1767 [ 0.818851] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.818855] io scheduler noop registered [ 0.818857] io scheduler anticipatory registered [ 0.818859] io scheduler deadline registered [ 0.818871] io scheduler cfq registered (default) [ 0.818885] pci 0000:00:02.0: Boot video device [ 0.818982] pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling [ 0.819300] isapnp: Scanning for PnP cards... [ 1.173668] isapnp: No Plug & Play device found [ 1.176248] Serial: 8250/16550 driver $Revision: 1.90 $ 10 ports, IRQ sharing enabled [ 1.176382] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.176509] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 1.177145] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.177327] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 1.177458] ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 1.177536] 0000:01:04.0: ttyS4 at MMIO 0xfebff000 (irq = 20) is a 16550A [ 1.177645] 0000:01:04.0: ttyS5 at MMIO 0xfebff200 (irq = 20) is a 16550A [ 1.177752] 0000:01:04.0: ttyS6 at MMIO 0xfebff400 (irq = 20) is a 16550A [ 1.177858] 0000:01:04.0: ttyS7 at MMIO 0xfebff600 (irq = 20) is a 16550A [ 1.177964] 0000:01:04.0: ttyS8 at MMIO 0xfebff800 (irq = 20) is a 16550A [ 1.178070] 0000:01:04.0: ttyS9 at MMIO 0xfebffa00 (irq = 20) is a 16550A [ 1.178177] 0000:01:04.0: ttyS2 at MMIO 0xfebffc00 (irq = 20) is a 16550A [ 1.178282] 0000:01:04.0: ttyS3 at MMIO 0xfebffe00 (irq = 20) is a 16550A [ 1.179659] brd: module loaded [ 1.179804] PNP: No PS/2 controller found. Probing ports directly. [ 1.182118] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.182123] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.182261] mice: PS/2 mouse device common for all mice [ 1.182387] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.182406] rtc0: alarms up to one month [ 1.182443] cpuidle: using governor ladder [ 1.182445] cpuidle: using governor menu [ 1.182450] No iBFT detected. [ 1.182866] TCP cubic registered [ 1.182869] NET: Registered protocol family 17 [ 1.182876] Using IPI No-Shortcut mode [ 1.182988] registered taskstats version 1 [ 1.183115] rtc_cmos 00:03: setting system clock to 2010-01-03 08:18:30 UTC (1262506710) [ 1.183242] Freeing unused kernel memory: 244k freed [ 1.272398] ACPI: SSDT 3F7CE0C0, 0688 (r1 AMI CPU1PM 1 INTL 20051117) [ 1.273002] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 1.273046] ACPI: ACPI0007:00 is registered as cooling_device0 [ 1.739819] usbcore: registered new interface driver usbfs [ 1.739847] usbcore: registered new interface driver hub [ 1.739880] usbcore: registered new device driver usb [ 1.741034] USB Universal Host Controller Interface driver v3.0 [ 1.741083] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 [ 1.741094] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 1.741098] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 1.741227] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 1.741263] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000dc00 [ 1.741346] usb usb1: configuration #1 chosen from 1 choice [ 1.741377] hub 1-0:1.0: USB hub found [ 1.741384] hub 1-0:1.0: 2 ports detected [ 1.819850] Uniform Multi-Platform E-IDE driver [ 1.819855] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 1.837757] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI [ 1.837760] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.844115] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.844119] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.844122] usb usb1: Product: UHCI Host Controller [ 1.844124] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 1.844127] usb usb1: SerialNumber: 0000:00:1d.0 [ 1.844203] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 1.844214] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 1.844219] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 1.844243] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 1.844278] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880 [ 1.844355] usb usb2: configuration #1 chosen from 1 choice [ 1.844383] hub 2-0:1.0: USB hub found [ 1.844389] hub 2-0:1.0: 2 ports detected [ 1.948109] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.948113] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.948117] usb usb2: Product: UHCI Host Controller [ 1.948119] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 1.948121] usb usb2: SerialNumber: 0000:00:1d.1 [ 1.948176] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 1.948186] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 1.948191] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 1.948214] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 1.948249] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800 [ 1.948325] usb usb3: configuration #1 chosen from 1 choice [ 1.948353] hub 3-0:1.0: USB hub found [ 1.948360] hub 3-0:1.0: 2 ports detected [ 1.976002] Marking TSC unstable due to: TSC halts in idle. [ 2.055866] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.055870] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.055873] usb usb3: Product: UHCI Host Controller [ 2.055875] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 2.055877] usb usb3: SerialNumber: 0000:00:1d.2 [ 2.055923] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16 [ 2.055932] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 2.055936] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 2.055958] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 2.055987] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d480 [ 2.056014] usb usb4: configuration #1 chosen from 1 choice [ 2.056014] hub 4-0:1.0: USB hub found [ 2.056014] hub 4-0:1.0: 2 ports detected [ 2.086974] usb 1-2: new low speed USB device using uhci_hcd and address 2 [ 2.158814] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.158818] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.158821] usb usb4: Product: UHCI Host Controller [ 2.158823] usb usb4: Manufacturer: Linux 2.6.26-2-686 uhci_hcd [ 2.158825] usb usb4: SerialNumber: 0000:00:1d.3 [ 2.158956] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 [ 2.158970] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 2.158974] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.158996] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 2.162913] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.162922] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 2.162927] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfea37c00 [ 2.220024] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 2.220079] usb usb5: configuration #1 chosen from 1 choice [ 2.220106] hub 5-0:1.0: USB hub found [ 2.220112] hub 5-0:1.0: 8 ports detected [ 2.324093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.324096] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.324099] usb usb5: Product: EHCI Host Controller [ 2.324102] usb usb5: Manufacturer: Linux 2.6.26-2-686 ehci_hcd [ 2.324104] usb usb5: SerialNumber: 0000:00:1d.7 [ 2.326736] No dock devices found. [ 2.334908] SCSI subsystem initialized [ 2.344019] libata version 3.00 loaded. [ 2.345016] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 2.370303] e100: eth0: e100_probe: addr 0xfebfe000, irq 20, MAC addr 00:30:59:04:25:2e [ 2.372518] ata_piix 0000:00:1f.2: version 2.12 [ 2.372535] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 2.372541] ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ] [ 2.372576] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 2.372629] scsi0 : ata_piix [ 2.372707] scsi1 : ata_piix [ 2.372737] ata1: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xcc00 irq 19 [ 2.372740] ata2: SATA max UDMA/133 cmd 0xd000 ctl 0xcc80 bmdma 0xcc08 irq 19 [ 2.617863] usb 1-2: device not accepting address 2, error -71 [ 2.673787] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2.703054] ICH7: IDE controller (0x8086:0x27df rev 0x02) at PCI slot 0000:00:1f.1 [ 2.703065] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 2.703074] ICH7: not 100% native mode: will probe irqs later [ 2.703084] ICH7: IDE port disabled [ 2.703092] ide0: BM-DMA at 0xffa0-0xffa7 [ 2.703098] Probing IDE interface ide0... [ 3.120023] usb 1-2: new low speed USB device using uhci_hcd and address 4 [ 3.216283] hdb: SILICONSYSTEMS UDMA 4GB-4300, ATA DISK drive [ 3.272061] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 3.272109] hdb: host side 80-wire cable detection failed, limiting max speed to UDMA33 [ 3.272112] hdb: UDMA/33 mode selected [ 3.272163] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 3.287664] hdb: max request size: 128KiB [ 3.287668] hdb: 8027712 sectors (4110 MB) w/1KiB Cache, CHS=7964/16/63 [ 3.287953] hdb: cache flushes supported [ 3.287987] hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 hdb7 hdb8 hdb9 > [ 3.371351] usb 1-2: configuration #1 chosen from 1 choice [ 3.372503] PM: Starting manual resume from disk [ 3.377441] usb 1-2: New USB device found, idVendor=1241, idProduct=1603 [ 3.377445] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.377448] usb 1-2: Product: USB Keyboard [ 3.377450] usb 1-2: Manufacturer: [ 3.409452] usbcore: registered new interface driver hiddev [ 3.409971] kjournald starting. Commit interval 5 seconds [ 3.409981] EXT3-fs: mounted filesystem with ordered data mode. [ 3.453644] input: USB Keyboard as /class/input/input0 [ 3.453691] input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.0-2 [ 3.539354] input: USB Keyboard as /class/input/input1 [ 3.548033] input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.0-2 [ 3.548052] usbcore: registered new interface driver usbhid [ 3.548056] usbhid: v2.6:USB HID core driver [ 3.769097] udevd version 125 started [ 4.358662] Linux agpgart interface v0.103 [ 4.367501] agpgart: Detected an Intel 945GME Chipset. [ 4.367836] agpgart: Detected 7932K stolen memory. [ 4.382966] agpgart: AGP aperture is 256M @ 0xd0000000 [ 4.527944] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 4.527964] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 4.557848] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... [ 4.585865] input: Power Button (FF) as /class/input/input2 [ 4.612654] ACPI: Power Button (FF) [PWRF] [ 4.612745] input: Power Button (CM) as /class/input/input3 [ 4.644048] ACPI: Power Button (CM) [PWRB] [ 5.710031] intel_rng: FWH not detected [ 5.740592] input: Video Bus as /class/input/input4 [ 5.764040] ACPI: Video Device [IGD] (multi-head: yes rom: no post: no) [ 5.782541] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 5.782613] iTCO_wdt: Found a ICH7-M DH TCO device (Version=2, TCOBASE=0x0860) [ 5.782642] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 5.880861] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19 [ 5.953481] input: PC Speaker as /class/input/input5 [ 5.975940] Error: Driver 'pcspkr' is already registered, aborting... [ 6.056711] Error: Driver 'pcspkr' is already registered, aborting... [ 6.250035] parport_pc 00:08: reported by Plug and Play ACPI [ 6.250087] parport0: PC-style at 0x378, irq 7 [PCSPP] [ 6.922157] Adding 489940k swap on /dev/hdb8. Priority:-1 extents:1 across:489940k [ 7.838259] loop: module loaded [ 7.851772] ppdev: user-space parallel port driver [ 8.350401] kjournald starting. Commit interval 5 seconds [ 8.350411] EXT3-fs: mounted filesystem with ordered data mode. [ 8.351728] kjournald starting. Commit interval 5 seconds [ 8.374635] EXT3 FS on hdb6, internal journal [ 8.374639] EXT3-fs: mounted filesystem with ordered data mode. [ 8.375522] kjournald starting. Commit interval 5 seconds [ 8.417212] EXT3 FS on hdb7, internal journal [ 8.417212] EXT3-fs: mounted filesystem with ordered data mode. [ 8.418360] kjournald starting. Commit interval 5 seconds [ 8.418360] EXT3-fs: mounted filesystem with ordered data mode. [ 8.418863] kjournald starting. Commit interval 5 seconds [ 8.434795] EXT3 FS on hdb5, internal journal [ 8.434795] EXT3-fs: mounted filesystem with ordered data mode. [ 9.485855] NET: Registered protocol family 10 [ 9.486264] lo: Disabled Privacy Extensions [ 9.558863] warning: `ntpd' uses 32-bit capabilities (legacy support in use) [ 21.053169] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.056131] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex [ 21.056478] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 32.048028] eth0: no IPv6 routers present
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:04.0 Unclassified device [0080]: Device 0002:0080
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:04.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09)
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
Subsystem: Intel Corporation Mobile 945GME Express Memory Controller Hub
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Mobile 945GME Express Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 15 Memory at fea80000 (32-bit, non-prefetchable) [size=512K] I/O ports at dc80 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fea40000 (32-bit, non-prefetchable) [size=256K] Capabilities: <access denied>
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Intel Corporation Device 27ae
Flags: bus master, fast devsel, latency 0
Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fea38000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at fea37c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
Subsystem: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffa0 [size=16] Kernel driver in use: PIIX_IDE Kernel modules: piix
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 I/O ports at d400 [size=8] I/O ports at d080 [size=4] I/O ports at d000 [size=8] I/O ports at cc80 [size=4] I/O ports at cc00 [size=16] Memory at fea37800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ata_piix Kernel modules: ata_piix
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller
Flags: medium devsel, IRQ 19
I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:04.0 Unclassified device [0080]: Device 0002:0080
Flags: fast devsel [virtual] Memory at feb00000 (32-bit, non-prefetchable) [disabled] [size=4K]
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
Subsystem: Intel Corporation Device 0001
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ec80 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: e100
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
Subsystem: Intel Corporation Mobile 945GME Express Memory Controller Hub
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Mobile 945GME Express Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 15 Memory at fea80000 (32-bit, non-prefetchable) [size=512K] I/O ports at dc80 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fea40000 (32-bit, non-prefetchable) [size=256K] Capabilities: <access denied>
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Intel Corporation Device 27ae
Flags: bus master, fast devsel, latency 0
Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fea38000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at fea37c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
Subsystem: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffa0 [size=16] Kernel driver in use: PIIX_IDE Kernel modules: piix
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 I/O ports at d400 [size=8] I/O ports at d080 [size=4] I/O ports at d000 [size=8] I/O ports at cc80 [size=4] I/O ports at cc00 [size=16] Memory at fea37800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ata_piix Kernel modules: ata_piix
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller
Flags: medium devsel, IRQ 19
I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:04.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09) (prog-if 02 [16550])
Flags: fast devsel, IRQ 20
Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: serial
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
Subsystem: Intel Corporation Device 0001
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ec80 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: e100
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cf000-000d07ff : Adapter ROM
000d0800-000d17ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3f7bffff : System RAM
00100000-002baaa0 : Kernel code
002baaa1-0037661f : Kernel data
003bc000-0041f57f : Kernel bss
3f7c0000-3f7cdfff : ACPI Tables
3f7ce000-3f7fffff : ACPI Non-volatile Storage
d0000000-dfffffff : 0000:00:02.0
e0000000-e3ffffff : pnp 00:0f
fe980000-fe9fffff : 0000:00:02.1
fea37800-fea37bff : 0000:00:1f.2
fea37c00-fea37fff : 0000:00:1d.7
fea37c00-fea37fff : ehci_hcd
fea38000-fea3bfff : 0000:00:1b.0
fea38000-fea3bfff : ICH HD audio
fea40000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.0
feb00000-febfffff : PCI Bus 0000:01
feb00000-feb00fff : 0000:01:04.0
febfe000-febfefff : 0000:01:08.0
febfe000-febfefff : e100
fec00000-fec00fff : pnp 00:0e
fed13000-fed19fff : pnp 00:01
fed1c000-fed1ffff : pnp 00:0b
fed20000-fed3ffff : pnp 00:0b
fed40000-fed8ffff : pnp 00:0b
fee00000-fee00fff : reserved
ffb00000-ffffffff : reserved
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cf000-000d07ff : Adapter ROM
000d0800-000d17ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-3f7bffff : System RAM
00100000-002baaa0 : Kernel code
002baaa1-0037661f : Kernel data
003bc000-0041f57f : Kernel bss
3f7c0000-3f7cdfff : ACPI Tables
3f7ce000-3f7fffff : ACPI Non-volatile Storage
d0000000-dfffffff : 0000:00:02.0
e0000000-e3ffffff : pnp 00:0f
fe980000-fe9fffff : 0000:00:02.1
fea37800-fea37bff : 0000:00:1f.2
fea37c00-fea37fff : 0000:00:1d.7
fea37c00-fea37fff : ehci_hcd
fea38000-fea3bfff : 0000:00:1b.0
fea38000-fea3bfff : ICH HD audio
fea40000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.0
feb00000-febfffff : PCI Bus 0000:01
febfe000-febfefff : 0000:01:08.0
febfe000-febfefff : e100
febff000-febfffff : 0000:01:04.0
febff000-febff007 : serial
febff200-febff207 : serial
febff400-febff407 : serial
febff600-febff607 : serial
febff800-febff807 : serial
febffa00-febffa07 : serial
febffc00-febffc07 : serial
febffe00-febffe07 : serialfec00000-fec00fff : pnp 00:0e
fed13000-fed19fff : pnp 00:01
fed1c000-fed1ffff : pnp 00:0b
fed20000-fed3ffff : pnp 00:0b
fed40000-fed8ffff : pnp 00:0b
fee00000-fee00fff : reserved
ffb00000-ffffffff : reserved
I added linux-pci because this appears PCI-related.
Quoted 4 lines · Alex Brooks
I have a problem getting a couple of PCI cards to play nicely together. ...
And (for both kernels) the output of lspci has the following line:
01:04.0 Unclassified device [0080]: Device 0002:0080
When you have only the 8-port serial card installed, it appears at 01:04.0. When you have both cards installed, we don't see a new device, and whatever is at 01:04.0 no longer looks like the octal UART.
Quoted 5 lines
Hardware Details:
- My motherboard is a DigitalLogic MSM945. It has a PC104 bus.
- I have two PC104 cards:
i) 8-port serial card (DiamondSystems Emerald-MM-8Plus)
ii) PC/104+ to MiniPCI Adapter (ConnectTech) (no MiniPCI cards installed).
Do you have these two cards?
http://www.diamondsystems.com/products/emeraldmm8plus,
http://www.connecttech.com/sub/Products/PC104plus_MiniPCI.asp
If so, both of those web pages mention jumpers that set the card's PCI device ("slot") number. My guess is that both of your cards are set to the same number.
Bjorn
Quoted 9 lines
Quoted 5 lines
I have a problem getting a couple of PCI cards to play nicely together.
...And (for both kernels) the output of lspci has the following line:
01:04.0 Unclassified device [0080]: Device 0002:0080When you have only the 8-port serial card installed, it appears at 01:04.0. When you have both cards installed, we don't see a new device, and whatever is at 01:04.0 no longer looks like the octal UART.
I'm pretty sure that it is the octal UART, but it isn't being recognised properly. To test this theory, I tried with (a) no cards at all, and (b) just the MiniPCI adapter (no serial card) -- nothing else appears at 01:04.0 (output of lspci attached).
Quoted 11 lines
Quoted 6 lines
Hardware Details:
- My motherboard is a DigitalLogic MSM945. It has a PC104 bus.
- I have two PC104 cards:
i) 8-port serial card (DiamondSystems Emerald-MM-8Plus) ii) PC/104+ to MiniPCI Adapter (ConnectTech) (no MiniPCI cards
installed).Do you have these two cards?
http://www.diamondsystems.com/products/emeraldmm8plus,
http://www.connecttech.com/sub/Products/PC104plus_MiniPCI.asp
Yes that's right.
Quoted 3 lines
If so, both of those web pages mention jumpers that set the card's PCI device ("slot") number. My guess is that both of your cards are set to the same number.
I'd already looked for this, I'm certain I have the jumpers right (I tried intentionally setting them incorrectly, the failure mode is different).
Alex
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GHM (ICH7-M DH) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:08.0 Ethernet controller: Intel Corporation PRO/100 VM Network Connection (rev 01)
Quoted 6 lines · Alex Brooks
Quoted 6 lines
Quoted 5 lines
I have a problem getting a couple of PCI cards to play nicely together.
...And (for both kernels) the output of lspci has the following line:
01:04.0 Unclassified device [0080]: Device 0002:0080
Quoted 6 lines
Quoted 3 lines
When you have only the 8-port serial card installed, it appears at 01:04.0. When you have both cards installed, we don't see a new device, and whatever is at 01:04.0 no longer looks like the octal UART.
I'm pretty sure that it is the octal UART, but it isn't being recognised properly.
I'm sure it *is* the UART, but we're getting the wrong data back from it, so we can't use it. The Mini PCI adapter must be interfering with the UART board somehow. Since you said the Mini PCI slot on the adapter is empty, and the jumpers are programmed correctly, I suspect the adapter is broken. Maybe a connector problem? Do you have another one that behaves the same way?
If you put a Mini PCI card in the slot and try this in a system without the UART card, does the Mini PCI card work correctly? The jumpers on the adapter should determine the PCI bus number where the Mini PCI device appears.
Quoted 3 lines
To test this theory, I tried with (a) no cards at all, and (b) just the MiniPCI adapter (no serial card) -- nothing else appears at 01:04.0 (output of lspci attached).
The PC/104+ to Mini PCI adapter looks like it's completely passive. It should be invisible to the OS, so it won't appear in lspci. For both cases, the lspci output you attached is exactly what I would expect.
I don't see any indication that this is a software problem (I know nothing about PC/104, so let me know if you disagree, and why).
Quoted 6 lines
Quoted 3 lines
If so, both of those web pages mention jumpers that set the card's PCI device ("slot") number. My guess is that both of your cards are set to the same number.
I'd already looked for this, I'm certain I have the jumpers right (I tried intentionally setting them incorrectly, the failure mode is different).
How did you set them, and what was the failure? If the adapter is really passive and the Mini PCI slot is empty, it seems strange that the adapter jumper setting would make any difference at all.
Bjorn