Skip to contentSkip to conversation

Hauppauge HVR-4400

DISCUSSION Jan Möbius 6 participants 12 messages May 4, 2010 – Nov 3, 2013 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It seems to be unsopported yet. Is there any driver which i don't know about?

If not i would really like to help getting it supported (information, testing,...)

Some information i get from the card:

Hauppauge HVR-4400 ( should be some kind of 4000 but with a pci-express interface )

04:00.0 Multimedia video controller [0400]: Conexant Systems, Inc. Hauppauge Inc. HDPVR-1250 model 1196 [14f1:8880] (rev 04)
Subsystem: Hauppauge computer works Inc. Device [0070:c108]
Flags: fast devsel, IRQ 18
Memory at e2000000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express Endpoint, MSI 00
Capabilities: [80] Power Management version 3
Capabilities: [90] Vital Product Data
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [100] Advanced Error Reporting
Capabilities: [200] Virtual Channel

The driver trying to access the card is cx23885 and it does not know the card and therefore falls back to generic.

If i force the driver to use the card HVR-1800 i get the following kernel log:
( Maybe this info is not reliable?! )

CORE cx23885[0]: subsystem: 0070:c108, board: Hauppauge WinTV-HVR1800 [card=2,insmod option]
tveeprom 2-0050: Hauppauge model 121019, rev B2F5, serial# 7157617 tveeprom 2-0050: MAC address is 00:0d:fe:6d:37:71
tveeprom 2-0050: tuner model is NXP 18271C2 (idx 155, type 54) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 2-0050: audio processor is CX23888 (idx 40)
tveeprom 2-0050: decoder processor is CX23888 (idx 34)
tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx23885[0]: warning: unknown hauppauge model #121019
cx23885[0]: hauppauge eeprom: model=121019
cx25840 4-0044: cx23888 A/V decoder found @ 0x88 (cx23885[0]) cx25840 4-0044: firmware: requesting v4l-cx23885-avcore-01.fw cx25840 4-0044: loaded v4l-cx23885-avcore-01.fw firmware (32522 bytes) tuner 3-0042: chip found @ 0x84 (cx23885[0])
tda9887 3-0042: creating new instance
tda9887 3-0042: tda988[5/6/7] found
tda9887 3-0042: destroying instance
tda8290: no gate control were provided!
cx23885[0]/0: registered device video1 [v4l2]
cx23885[0]: registered device video2 [mpeg] cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
cx23885[0]: frontend initialization failed
cx23885_dvb_register() dvb_register failed err = -1 cx23885_dev_setup() Failed to register dvb on VID_C cx23885_dev_checkrevision() Hardware revision = 0xd0 cx23885[0]/0: found at 0000:04:00.0, rev: 4, irq: 18, latency: 0, mmio:
0xe2000000
cx23885 0000:04:00.0: setting latency timer to 64
IRQ 18/cx23885[0]: IRQF_DISABLED is not guaranteed on shared IRQs

Best Regards,
Jan Möbius

#1 lore raw
Quoted 4 lines · Jan Möbius

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It seems to be unsopported yet. Is there any driver which i don't know about?

There is no support currently for that card, and since it uses a demodulator for which there is not currently a driver, much more work will be required than simply adding a new board profile.

Devin

Signature · 2 lines
Devin J. Heitmueller - Kernel Labs
http://www.kernellabs.com
#2 lore raw

Oh wow I didn't know Haupauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2? I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

Cheers,
Jed

Quoted 14 lines · Devin Heitmueller
Quoted 5 lines · Jan Möbius

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It seems to be unsopported yet. Is there any driver which i don't know about?

There is no support currently for that card, and since it uses a demodulator for which there is not currently a driver, much more work will be required than simply adding a new board profile.

Devin

#3 lore raw
In reply to Devin Heitmueller

Oh wow I didn't know Hauppauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2? I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

Cheers,
Jed

Quoted 14 lines · Devin Heitmueller
Quoted 5 lines · Jan Möbius

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It seems to be unsopported yet. Is there any driver which i don't know about?

There is no support currently for that card, and since it uses a demodulator for which there is not currently a driver, much more work will be required than simply adding a new board profile.

Devin

#4 lore raw
Quoted 6 lines · Jed

Oh wow I didn't know Hauppauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2?
I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

It's completely different.

Signature · 2 lines
Steven Toth - Kernel Labs
http://www.kernellabs.com
#5 lore raw
Quoted 10 lines · Jed
Quoted 7 lines

Oh wow I didn't know Hauppauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2?
I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

It's completely different.

Bummer!!! :(
Why'd they have to go & use a completely different architecture, lame.

#6 lore raw
In reply to Steven Toth
Quoted 10 lines · Jed
Quoted 7 lines

Oh wow I didn't know Hauppauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2?
I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

It's completely different.

Bummer!!! :(
Why'd they have to go & use a completely different architecture, lame. --
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#7 lore raw
In reply to Steven Toth
Quoted 10 lines · Jed
Quoted 7 lines

Oh wow I didn't know Hauppauge had released some new models above the 2200.
http://www.hauppauge.co.uk/site/products/prods_hvr_internal.html
Is this 4400 exactly the same as the HVR-2200, aside from the demodulator used for it's DVB-S/S2?
I hope so, that way work being done on the 2200 can flow onto this! (cept for DVB-S/S2)

It's completely different.

Bummer!!! :(
Why'd they have to go & use a completely different architecture, lame. --
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#8 lore raw
Quoted 1 line

Why'd they have to go & use a completely different architecture, lame.

It's just business, get used to it. If you don't like their stuff then buy a different product. Vote with your wallet. That's the power you have as a consumer.

Signature · 2 lines
Steven Toth - Kernel Labs
http://www.kernellabs.com
#9 lore raw
Quoted 5 lines · Steven Toth
Quoted 1 line

Why'd they have to go & use a completely different architecture, lame.

It's just business, get used to it. If you don't like their stuff then buy a different product. Vote with your wallet. That's the power you have as a consumer.

Just seems counter-intuitive to use an entirely diff. platform. From a business perspective....

#10 lore raw
In reply to Devin Heitmueller
Quoted 5 lines · Devin Heitmueller <dheitmueller <at> kernellabs.com> writes:
Quoted 3 lines · On Tue, May 4, 2010 at 8:00 AM, Jan Möbius <jan_moebius <at> web.de> wrote:

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It

seems to

Quoted 8 lines
Quoted 1 line

be unsopported yet. Is there any driver which i don't know about?

There is no support currently for that card, and since it uses a demodulator for which there is not currently a driver, much more work will be required than simply adding a new board profile.

Devin

Well, DVB-S/S2 seems to be finally supported using a current kernel (3.11).

I get the following files under /dev/dvb/adapter0:

demux0
dvr0
frontend0
net0

w_scan also works (as described here[1]).

But the card has multiple tuners (DVB-T/C and analogue as well) which are not recognized.

Is there any information I can give you to help support this card?

I have little experience in C but no experience in programming hardware, but am willing to help in anyway needed.

Kind regards
Christoph

[1] http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4400

#11 lore raw

Am Mittwoch, den 23.10.2013, 16:58 +0000 schrieb Christoph Schwerdtfeger:

Quoted 17 lines
Quoted 5 lines · Devin Heitmueller <dheitmueller <at> kernellabs.com> writes:
Quoted 3 lines · On Tue, May 4, 2010 at 8:00 AM, Jan Möbius <jan_moebius <at> web.de> wrote:

Hi,

im trying to get a Hauppauge HVR-4400 working on a Debian squeeze. It

seems to

Quoted 8 lines
Quoted 1 line

be unsopported yet. Is there any driver which i don't know about?

There is no support currently for that card, and since it uses a demodulator for which there is not currently a driver, much more work will be required than simply adding a new board profile.

Devin

Quoted 6 lines

Well, DVB-S/S2 seems to be finally supported using a current kernel (3.11).

But the card has multiple tuners (DVB-T/C and analogue as well) which are not recognized.

Is there any information I can give you to help support this card?

Ok, that DVB-C part was crap, there's no such tuner onboard. But there's an analogue tuner onboard which seems to be recognized by the current kernel:

[...]

[    2.894012] tveeprom 9-0050: Hauppauge model 121029, rev B2F5,
serial# 7264773
[    2.894014] tveeprom 9-0050: MAC address is 00:0d:fe:6e:da:05
[    2.894015] tveeprom 9-0050: tuner model is NXP 18271C2 (idx 155,
type 54)
[    2.894016] tveeprom 9-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L')
PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
[    2.894017] tveeprom 9-0050: audio processor is CX23888 (idx 40)
[    2.894018] tveeprom 9-0050: decoder processor is CX23888 (idx 34)
[    2.894019] tveeprom 9-0050: has radio, has IR receiver, has no IR
transmitter
[    2.894020] cx23885[0]: warning: unknown hauppauge model #121029
[    2.894021] cx23885[0]: hauppauge eeprom: model=121029
[    2.894022] cx23885_dvb_register() allocating 1 frontend(s)

[...]

But I have no video device listed under /dev.

Is there any information on the analogue tuner and how to get it working or some information on how to start write a driver?
I would like to try to put something together - probably killing the card. ;-)

Any help and information on that topic is appreciated!

Kind regards
Christoph