Skip to contentSkip to conversation

Cloning arch-independant KConfig

DISCUSSION Joel Becker 2 participants 3 messages Aug 12, 2010 – Aug 13, 2010

lore
Share & tools
lore
#0 lore raw

Sam,
I guess this is either a feature request or just wondering
whether KConfig supports this idea.
Often I have a wonderful minimal .config that builds a test
kernel. It only compiles the things I want in my kernel and modules, nothing more. Usually I start from a distro kernel and then keep turning things off until I reach some minimum.
However, when I get a new machine of a different architecture, I
can't bring that work forward. If I take this .config to that arch, the oldconfig just breaks. I don't get good defaults for the arch-specific stuff. Conversely, if I start from a distro .config for the new arch, I have to repeat all the whittle-down work.
Is there any way to "extract" the non-arch-specific config
values? Essentially, all the "use USB, build ext3, give me these network cards" fields should be kept, but I want to start from a default architecture config.

Joel

Signature · 8 lines
"Friends may come and go, but enemies accumulate." 
        - Thomas Jones

Joel Becker
Consulting Software Developer
Oracle
E-mail: [email protected]
Phone: (650) 506-8127
#1 lore raw
Quoted 8 lines · Joel Becker

Sam,
I guess this is either a feature request or just wondering
whether KConfig supports this idea.
Often I have a wonderful minimal .config that builds a test
kernel. It only compiles the things I want in my kernel and modules, nothing more. Usually I start from a distro kernel and then keep turning things off until I reach some minimum.
However, when I get a new machine of a different architecture, I

Quoted 8 lines

can't bring that work forward. If I take this .config to that arch, the oldconfig just breaks. I don't get good defaults for the arch-specific stuff. Conversely, if I start from a distro .config for the new arch, I have to repeat all the whittle-down work.
Is there any way to "extract" the non-arch-specific config
values? Essentially, all the "use USB, build ext3, give me these network cards" fields should be kept, but I want to start from a default architecture config.

Today there are a few ways you can do so already.
Say that you have saved away the known good one as "good", which is a direct copy of your .config.

Then you can do for example:
KCONFIG_ALLCONFIG=good make alldefconfig

This will produce a config wich is almost equal to what you had before, and with defaults for all new stuff.
I tested it where I used a sparc defconfig as input to a i386 config and it just worked.

Another possibility:
If you already have configured your kernel, but want to use "good" but keep the settings for all the new stuff. Then you can do:

cat .config good > new
mv new .config
make menuconfig

This will trigger a lot of override warnings - which you just ignore. Resulting config is then mostly from "good".

We do not have a way to say "copy only non-arch specific settings". So I hope the above is OK.

Sam

#2 lore raw
Quoted 11 lines · Sam Ravnborg

Today there are a few ways you can do so already.
Say that you have saved away the known good one as "good", which is a direct copy of your .config.

Then you can do for example:
KCONFIG_ALLCONFIG=good make alldefconfig

This will produce a config wich is almost equal to what you had before, and with defaults for all new stuff.
I tested it where I used a sparc defconfig as input to a i386 config and it just worked.

That seems pretty reasonable.

Quoted 6 lines

cat .config good > new
mv new .config
make menuconfig

This will trigger a lot of override warnings - which you just ignore. Resulting config is then mostly from "good".

The problem with this, which I've definitely done before, is I
never know what paths in menuconfig to look down. The alldefconfig choice seems saner because it provides a dirt-simple CPU setup.

Joel

Signature · 9 lines
"Can any of you seriously say the Bill of Rights could get through
 Congress today?  It wouldn't even get out of committee."
	- F. Lee Bailey

Joel Becker
Consulting Software Developer
Oracle
E-mail: [email protected]
Phone: (650) 506-8127