Skip to contentSkip to conversation

btrfs and raid1 (restore)

DISCUSSION Felix Blanke 2 participants 3 messages Sep 7, 2010 – Sep 8, 2010 Btrfs file system

lore
Share & tools
lore
#0 lore raw

Hi,

I made a REALLY bad mistake today.

I've two hdds which are running at raid1 via btrfs. Today I mistyped a device-node and did a "mkfs.vfat" on one of them.

Then I simply did a "btrfs filesystem balance /path/". "btrfs filesystem show /path/" now looks like this:

Label: 'home1' uuid: c3c38f32-f176-4479-8c44-e832ea64639f

    Total devices 2 FS bytes used 226.12GB
    devid    2 size 465.76GB used 114.38GB path /dev/loop3
    devid    1 size 465.76GB used 114.39GB path /dev/loop4

Before my mistake the "FS bytes used" were all three the same, now the bottom two are only half of the size. Am I right that those devices didnt run in raid1 mode anymore? :(

Is there a way, without copying back all data from my backup, to get those 2 running in raid1 mode?
Or do I have to make a "mkfs.btrfs -m raid1 -d raid1 /dev/1", "btrfs device add /dev/2" and "btrfs filesystem balance /path/"? :/ That would cost a lot of time.

Thanks for your help!

Regards,
Felix

#1 lore raw

Now that we know the facts, what is the problem? Some simple questions first; Is the data still accessible?
What did the rebalance do?
Output of btrfsck/dmesg?
mkfs.vfat does not write much on disk so if the rebalance was also made before the mkfs I guess most data is still present.

Sent from my mobile device.

Quoted 36 lines · Felix Blanke

Hi,

I made a REALLY bad mistake today.

I've two hdds which are running at raid1 via btrfs. Today I mistyped a device-node and did a "mkfs.vfat" on one of them.

Then I simply did a "btrfs filesystem balance /path/". "btrfs filesystem show /path/" now looks like this:

Label: 'home1' uuid: c3c38f32-f176-4479-8c44-e832ea64639f
Total devices 2 FS bytes used 226.12GB
devid 2 size 465.76GB used 114.38GB path /dev/loop3
devid 1 size 465.76GB used 114.39GB path /dev/loop4

Before my mistake the "FS bytes used" were all three the same, now the bottom two are only half of the size. Am I right that those devices didnt run in raid1 mode anymore? :(

Is there a way, without copying back all data from my backup, to get those 2 running in raid1 mode?
Or do I have to make a "mkfs.btrfs -m raid1 -d raid1 /dev/1", "btrfs device add /dev/2" and "btrfs filesystem balance /path/"? :/ That would cost a lot of time.

Thanks for your help!

Regards,
Felix
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

The Questions are in my e-mail?!

=46irst of all the answers to your questions:

- All data still accessible
-
cooter ~ # btrfsck /dev/disk/by-label/home1
found 242881646593 bytes used err is 0
total csum bytes: 236710380
total tree bytes: 525582336
total fs tree bytes: 219082752
btree space waste bytes: 99723364
file data blocks allocated: 284825751552
referenced 242200633344
Btrfs v0.19-16-g075587c-dirty

- ofc i did a balance before the mkfs, the raid was running for some we= eks now.

My questions again in a short version:

- Is there a way to see if the 2 devices are still running in raid1 mod= e? The 'btrfs
filesystem show' doesn't fit to the old one (like described before) s=
o it seems
that they are now running in a non raid1 mode.
- Is there a way to get those 2 devices running in raid1 mode again wit= hout creating
a new filesystem, adding the second device, copying data back etc.?

Regards,
=46elix

Quoted 7 lines · On 07. September 2010 - 20:46, J=E9r=F4me Poulin wrote:

Date: Tue, 7 Sep 2010 20:46:19 -0400
From: J=E9r=F4me Poulin <[email protected]>
To: Felix Blanke <[email protected]>
Cc: "[email protected]" <[email protected]>
Subject: Re: btrfs and raid1 (restore)
=20
Now that we know the facts, what is the problem? Some simple question=

s first;

Quoted 15 lines

Is the data still accessible?
What did the rebalance do?
Output of btrfsck/dmesg?
mkfs.vfat does not write much on disk so if the rebalance was also made before the mkfs I guess most data is still present. =20
Sent from my mobile device.
=20
On 2010-09-07, at 18:28, Felix Blanke <[email protected]> wrote:
=20

Quoted 5 lines

Hi,

I made a REALLY bad mistake today.

I've two hdds which are running at raid1 via btrfs. Today I mistype=

d a device-node

Quoted 3 lines
Quoted 3 lines

and did a "mkfs.vfat" on one of them.

Then I simply did a "btrfs filesystem balance /path/". "btrfs files=

ystem show /path/"

Quoted 9 lines
Quoted 9 lines

now looks like this:

Label: 'home1' uuid: c3c38f32-f176-4479-8c44-e832ea64639f
Total devices 2 FS bytes used 226.12GB
devid 2 size 465.76GB used 114.38GB path /dev/loop3
devid 1 size 465.76GB used 114.39GB path /dev/loop4

Before my mistake the "FS bytes used" were all three the same, now =

the bottom two are

Quoted 1 line
Quoted 1 line

only half of the size. Am I right that those devices didnt run in r=

aid1 mode anymore?

Quoted 4 lines
Quoted 4 lines

:(

Is there a way, without copying back all data from my backup, to ge=

t those 2 running in

Quoted 2 lines
Quoted 2 lines

raid1 mode?
Or do I have to make a "mkfs.btrfs -m raid1 -d raid1 /dev/1", "btrf=

s device add /dev/2" and

Quoted 1 line
Quoted 1 line

"btrfs filesystem balance /path/"? :/ That would cost a lot of time=

=2E

Quoted 9 lines
Quoted 9 lines

Thanks for your help!

Regards,
Felix
--
To unsubscribe from this list: send the line "unsubscribe linux-btr=

fs" in

Quoted 2 lines
Quoted 2 lines

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

---end quoted text---
--
To unsubscribe from this list: send the line "unsubscribe linux-btrfs" = in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html