hwmon: (w83795) Add support for dynamic
Subsystems (2)
PATCH 17/36 hwmon: (w83795) Add support for dynamic
The W83795G can be configured to set the in0, in1 and/or in2 voltage limits dynamically based on VID input pins. Switch the respective sysfs attributes to read-only.
Signed-off-by Jean Delvare <[email protected]>
--- drivers/hwmon/w83795.c | 56 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 56 insertions(+)
drivers/hwmon/w83795.c +54 -0
@@ -316,6 +316,7 @@ struct w83795_data {u8 bank;u32 has_in;/* Enable monitor VIN or not */ +u8 has_dyn_in;/* Only in2-0 can have this */ u16 in[21 ][3 ];/* Register value, read/high/low */ u8 in_lsb[10 ][3 ];/* LSB Register value, high/low */ u8 has_gain;/* has gain: in17-20 * 8 */
@@ -450,6 +451,23 @@ static struct w83795_data *w83795_update data->in[i][IN_READ ] = tmp; } +/* in0-2 can have dynamic limits (W83795G only) */ +if (data->has_dyn_in) { +u8 lsb_max =w83795_read (client,IN_LSB_REG (0 ,IN_MAX )); +u8 lsb_low =w83795_read (client,IN_LSB_REG (0 ,IN_LOW )); + +for (i =0 ; i <3 ; i++) { +if (!(data->has_dyn_in & (1 << i))) +continue ; + data->in[i][IN_MAX ] +w83795_read (client,W83795_REG_IN [i][IN_MAX ]); + data->in[i][IN_LOW ] +w83795_read (client,W83795_REG_IN [i][IN_LOW ]); + data->in_lsb[i][IN_MAX ] = (lsb_max >> (2 * i)) &0x03 ; + data->in_lsb[i][IN_LOW ] = (lsb_low >> (2 * i)) &0x03 ; + } + } +/* Update fan */ for (i =0 ; i <ARRAY_SIZE (data->fan); i++) {if (!(data->has_fan & (1 << i)))
@@ -1450,6 +1468,8 @@ store_sf_setup(struct device *dev, struc#define NOT_USED -1 +/* Don't change the attribute order, _max and _min are accessed by index +* somewhere else in the code */ #define SENSOR_ATTR_IN (index) { \ SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL, \ IN_READ, index), \
@@ -1844,6 +1864,39 @@ static int device_remove_file_wrapper(streturn 0 ; } +static void w83795_check_dynamic_in_limits (struct i2c_client *client) +{ +struct w83795_data *data =i2c_get_clientdata (client); +u8 vid_ctl; +int i, err_max, err_min; + + vid_ctl =w83795_read (client,W83795_REG_VID_CTRL ); + +/* Return immediately if VRM isn't configured */ +if ((vid_ctl &0x07 ) =0x00 || (vid_ctl &0x07 ) =0x07 ) +return ; + + data->has_dyn_in = (vid_ctl >>3 ) &0x07 ; +for (i =0 ; i <2 ; i++) { +if (!(data->has_dyn_in & (1 << i))) +continue ; + +/* Voltage limits in dynamic mode, switch to read-only */ + err_max =sysfs_chmod_file (&client->dev.kobj, + &w83795_in[i][2 ].dev_attr.attr, +S_IRUGO ); + err_min =sysfs_chmod_file (&client->dev.kobj, + &w83795_in[i][3 ].dev_attr.attr, +S_IRUGO ); +if (err_max || err_min) +dev_warn (&client->dev,"Failed to set in%d limits " +"read-only (%d, %d)\n" , i, err_max, err_min); +else +dev_info (&client->dev,"in%d limits set dynamically " +"from VID\n" , i); + } +} +/* Check pins that can be used for either temperature or voltage monitoring */ static void w83795_apply_temp_config (struct w83795_data *data,u8 config,int temp_chan,int in_chan)
@@ -2049,6 +2102,9 @@ static int w83795_probe(struct i2c_clienif (err) goto exit_remove; +if (data->chip_type = w83795g) +w83795_check_dynamic_in_limits (client); + data->hwmon_dev =hwmon_device_register (dev);if (IS_ERR (data->hwmon_dev)) { err =PTR_ERR (data->hwmon_dev);
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors