Unable to get CF working on HP Jornada 700 flashrom
Kristoffer Ericson
maintainerGreetings,
Ive looked at this for a couple of days now and havent reached any solution. So any feedback whatsoever is greatly appreciated.
It boots up (from u-boot) but is unable to find the compact flash card and therefore
panics. I have however earlier (cant seem to reproduce it now) had a situation when the CF worked at the expense of the MCU, havent managed to get both working at same time.
Best wishes
Kristoffer Ericson
-------------- next part --------------
arch/arm/mach-sa1100/jornada720.c +88 -15
@@ -35,12 +35,13 @@#include "generic.h" +#define SBI_SKCR __REG(SA1111_VBASE) +/* * HP Documentation referred in this file: * http://www.jlime.com/downloads/development/docs/jornada7xx/jornada720.txt */ -/* line 110 of HP's doc */ #define TUCR_VAL 0x20000400/* memory space (line 52 of HP's doc) */
@@ -241,32 +242,104 @@ static struct platform_device jornada_ts_device = { .id = -1, }; +static struct platform_device jornada_bl_device = { + .name ="jornada_bl" , + .id =-1 , +}; + +static struct platform_device jornada_lcd_device = { + .name ="jornada_lcd" , + .id =-1 , +}; + +static struct platform_device *devices[]__initdata = { &sa1111_device, &jornada_ssp_device, &s1d13xxxfb_device, &jornada_kbd_device, &jornada_ts_device, + &jornada_bl_device, + &jornada_lcd_device, };static int __init jornada720_init (void ) {int ret = -ENODEV ; +int i; -if (machine_is_jornada720 ()) { -/* we want to use gpio20 as input to drive the clock of our uart 3 */ -GPDR |=GPIO_GPIO20 ;/* Clear gpio20 pin as input */ -TUCR =TUCR_VAL ; -GPSR =GPIO_GPIO20 ;/* start gpio20 pin */ -udelay (1 ); -GPCR =GPIO_GPIO20 ;/* stop gpio20 */ -udelay (1 ); -GPSR =GPIO_GPIO20 ;/* restart gpio20 */ -udelay (20 );/* give it some time to restart */ - - ret =platform_add_devices (devices,ARRAY_SIZE (devices)); - } +printk (KERN_INFO "HP Jornada 710/720/728 Machine Init\n" ); + +/* +* PIN Settings from wince +* +* (GPDR) PINs configured as outputs (all others are inputs) +* GPIO8, GPIO11, GPIO17, GPIO19, GPIO20, GPIO21, GPIO24, GPIO25, GPIO27 +* +* (GPSR) PINs configures as outputs with level high +* GPIO11, GPIO20, GPIO25 +* +* (GPCR) PINs configured as pin level low +* GPIO08, GPIO17, GPIO19, GPIO21, GPIO24, GPIO27 +* +* (GRER) PINs configured to detect rising edge GPIOs +* GPIO01, GPIO15, GPIO18 +* +* (GFER) PINs configured to detect falling edge GPIOs +* GPIO15, GPIO18 +* +* (GAFR) PINs configure to use alternate function +* GPIO21, GPIO22, GPIO27 +* +* (PPDR) PIN directions (default after reset is input) +* LDD(0,1,2,3) = General Purpose Output +* +* (PPSR) Pin Directions +* LDD(4,5,6) +* L_BIAS +*/ + +sa1110_mb_disable (); + +/* we want to use gpio20 as input to drive the clock of our uart 3 */ +GPDR |=GPIO_GPIO20 ;/* make sure its set as ouput */ +TUCR =TUCR_VAL ;// reserve GPIO21/22 for use as MBGNT/MBREQ +GPSR =GPIO_GPIO20 ;/* start gpio20 pin */ +udelay (50 ); +GPCR =GPIO_GPIO20 ;/* clear pin level gpio20 */ +udelay (50 ); +GPSR =GPIO_GPIO20 ;/* restart gpio20 */ +udelay (50 );/* give it some time to restart */ + +SBI_SKCR = (SKCR_OE_EN |SKCR_PLL_BYPASS |SKCR_RDYEN ); +mdelay (200 ); + +SBI_SKCR = (SKCR_OE_EN |SKCR_PLL_BYPASS |SKCR_RDYEN |SKCR_RCLKEN ); +PPDR =0x000049FF ; + +/* Reset the MCU */ +PPSR &= (PPC_L_FCLK |0x80 |PPC_LDD (1 ) |PPC_LDD (0 )); +udelay (1000 ); + +PPDR |= (PPC_L_FCLK |0x80 |PPC_LDD (1 ) |PPC_LDD (0 )); +udelay (1000 ); + +PPSR |=PPC_L_FCLK ; +udelay (1000 ); + +GPSR =GPIO_GPIO25 ; +GPDR |=GPIO_GPIO25 ; + + Ser4SSCR0 =0x0307 ;// set 8-bit data, setting transmission rate + Ser4MCCR0 =0x0 ;// disable MCP and leave everything to the SSP + Ser4SSSR =0x0 ;// remove overruns (rest is read-only) + Ser4SSCR1 =0x18 ;// Inactive SCLK = high, starting position + Ser4SSCR0 =0x0387 ; + +while (Ser4SSSR &SSSR_RNE ) + i = Ser4SSDR; + ret =platform_add_devices (devices,ARRAY_SIZE (devices));return ret; }
@@ -353,7 +426,7 @@ static struct flash_platform_data jornada720_flash_data = {static struct resource jornada720_flash_resource = { .start =SA1100_CS0_PHYS , - .end =SA1100_CS0_PHYS +SZ_32M -1 , + .end =SA1100_CS0_PHYS +SZ_64M -1 , .flags =IORESOURCE_MEM , };