Skip to contentSkip to conversation

Sam9g45 USB CDC

U-Boot Marcel 2 participants 3 messages Oct 5, 2010 – Oct 9, 2010

lore
Share & tools
lore

Marcel

author
#0 lore raw

Hi,

It looks like I've got most thing implemented regarding USB CDC for the Sam9g45. I do however have some basic questions.

One of the things is that I don't see any descriptors in Windows. I installed some inf file found on the net for Ethernet RNDIS but maybe that was wrong. Is there any Windows driver available for the Linux CDC interface ?

Second I connected the device to my Linux host and dmesg says looks a bit better :

usb 1-4: USB disconnect, address 39
usb 1-4: new high speed USB device using ehci_hcd and address 40 usb 1-4: New USB device found, idVendor=0525, idProduct=a4a1 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-4: Product: Ethernet Gadget
usb 1-4: Manufacturer: Atmel AT91SAM9G45
usb 1-4: configuration #1 chosen from 1 choice

lusb output is shown below. I see the following line :
iMacAddress 3 (??)
Is this normal or did I perhaps miss something crucial here ?

One thing I notice is that things are rather slow in Linux and probably also the reason why things don't work in windows yet. It takes a couple of seconds for lsusb to show information and my guess is that still something is wrong.

Best regards,
Marcel

$lsusb -v -d 0525:a4a1

Bus 001 Device 036: ID 0525:a4a1 Netchip Technology, Inc. Linux-USB Ethernet Gadget
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            2 Communications
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0525 Netchip Technology, Inc.
  idProduct          0xa4a1 Linux-USB Ethernet Gadget
  bcdDevice            3.18
  iManufacturer           1 
  iProduct                2 
  iSerial                 0 
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 80
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 7
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 6 Ethernet Networking
bInterfaceProtocol 0
iInterface 5
CDC Header:
bcdCDC 1.10
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Ethernet:
iMacAddress 3 (??)
bmEthernetStatistics 0x00000000
wMaxSegmentSize 1536
wNumberMCFilters 0x0000
bNumberPowerFilters 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
can't get device qualifier: Connection timed out can't get debug descriptor: Connection timed out cannot read device status, Connection timed out (110)

author
#1 lore raw

Hi,

Never mind, I overlooked the string descriptors.
The funny thing is that the Linux host just continues where the windows host simply stops communicating with the device.

regards,
Marcel

Quoted 140 lines

Hi,

It looks like I've got most thing implemented regarding USB CDC for the Sam9g45. I do however have some basic questions.

One of the things is that I don't see any descriptors in Windows. I installed some inf file found on the net for Ethernet RNDIS but maybe that was wrong. Is there any Windows driver available for the Linux CDC interface ?

Second I connected the device to my Linux host and dmesg says looks a bit better :

usb 1-4: USB disconnect, address 39
usb 1-4: new high speed USB device using ehci_hcd and address 40 usb 1-4: New USB device found, idVendor=0525, idProduct=a4a1 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-4: Product: Ethernet Gadget
usb 1-4: Manufacturer: Atmel AT91SAM9G45
usb 1-4: configuration #1 chosen from 1 choice

lusb output is shown below. I see the following line :
iMacAddress 3 (??)
Is this normal or did I perhaps miss something crucial here ?

One thing I notice is that things are rather slow in Linux and probably also the reason why things don't work in windows yet. It takes a couple of seconds for lsusb to show information and my guess is that still something is wrong.

Best regards,
Marcel

$lsusb -v -d 0525:a4a1

Bus 001 Device 036: ID 0525:a4a1 Netchip Technology, Inc. Linux-USB Ethernet Gadget
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            2 Communications
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0525 Netchip Technology, Inc.
  idProduct          0xa4a1 Linux-USB Ethernet Gadget
  bcdDevice            3.18
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 80
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 7
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 6 Ethernet Networking
bInterfaceProtocol 0
iInterface 5
CDC Header:
bcdCDC 1.10
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Ethernet:
iMacAddress 3 (??)
bmEthernetStatistics 0x00000000
wMaxSegmentSize 1536
wNumberMCFilters 0x0000
bNumberPowerFilters 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
can't get device qualifier: Connection timed out can't get debug descriptor: Connection timed out cannot read device status, Connection timed out (110)
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#2 lore raw
In reply to Marcel

Hi,

2010/10/5 Marcel <[email protected]>:

Quoted 7 lines

Hi,

It looks like I've got most thing implemented regarding USB CDC for the Sam9g45. I do however have some basic questions.

One of the things is that I don't see any descriptors in Windows. I installed some inf file found on the net for Ethernet RNDIS but maybe that was wrong.

RNDIS is not supported in U-boot.

Quoted 1 line

Is there any Windows driver available for the Linux CDC interface ?

This driver works reliable in our situation combined with the CDC-layer of U-boot:
http://www.thesycon.de/eng/usb_cdcecm.shtml

Kind regards,

Remy