Skip to contentSkip to conversation

watchdog - v2.6.37-rc1

GIT PULL Wim Van Sebroeck 1 participant 1 message Oct 28, 2010 Watchdog device drivers

lore
Share & tools
lore
#0 lore raw

Hi Linus,

Please pull from 'master' branch of
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
or if master.kernel.org hasn't synced up yet:
master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git

This will update the following files:

 drivers/watchdog/Kconfig       |   23 +-
 drivers/watchdog/Makefile      |    1 
 drivers/watchdog/bcm63xx_wdt.c |  350 +++++++++++++++++++++++++++++++++++++++++
 drivers/watchdog/f71808e_wdt.c |   10 +
 drivers/watchdog/iTCO_wdt.c    |   26 +--
 drivers/watchdog/it8712f_wdt.c |   25 +-
 drivers/watchdog/it87_wdt.c    |   96 +++++++----
 drivers/watchdog/machzwd.c     |    4 
 8 files changed, 479 insertions(+), 56 deletions(-)

with these Changes:

Author: Prarit Bhargava <[email protected]>
Date:   Wed Oct 27 09:50:22 2010 -0400

watchdog: iTCO_wdt.c: remove extra pci_dev_put()'s from init code

The iTCO_wdt driver erroneously releases the pci_dev, and causes PCI hotremove to fail because of an incorrect usage count.

The probe for this driver does a for_each_pci_dev() which gets a reference for a pci_dev when iTCO_wdt_init() is successful. The for_each_pci_dev() loop puts a reference for a pci_dev when iTCO_wdt_init() fails, so the iTCO_wdt_init() does not need to do any pci_dev_put()'s.

The only pci_dev_put() that is required is in the iTCO_wdt_cleanup() function.

Author: Florian Fainelli <[email protected]>
Date:   Sat Aug 28 22:03:45 2010 +0200

watchdog: add support for Broadcom BCM63xx built-in watchdog

This patch adds support for the Broadcom BCM63xx SoC built-in watchdog, it uses one of the BCM63xx hardware timer id.

Author: Giel van Schijndel <[email protected]>
Date:   Mon Oct 4 10:45:28 2010 +0200

watchdog: f71808e_wdt: add support for the F71889FG

Author: Nicolas Kaiser <[email protected]>
Date:   Sat Oct 9 14:19:46 2010 +0200

watchdog: MachZ: fix debug macro

Fix debug macro line wrapping.

Author: Timo Juhani Lindfors <[email protected]>
Date:   Thu Sep 30 17:08:04 2010 +0300

watchdog: it8712f_wdt: Add module parameter for alternative reset sources

On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads from the game port do not seem to reset the watchdog timer. This patch adds a module parameter wdt_config_reg to specify alternative reset sources. At least WDT_RESET_KBD has been tested, even just running

while true; do
setleds -L +scroll
sleep 1
setleds -L -scroll
sleep 1
done

is enough to keep the watchdog happy.

Author: Timo Juhani Lindfors <[email protected]>
Date:   Thu Sep 30 17:08:03 2010 +0300

watchdog: it8712f_wdt: Add comments for config/control register names

Author: Ondrej Zajicek <[email protected]>
Date:   Tue Sep 14 02:54:16 2010 +0200

watchdog: it87_wdt: Add support for watchdogs with 8b timers

This patch adds support for watchdogs with 8b timers, like ones in IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt driver. This patch should be used after the patch 'it87_wdt: Add support for IT8720F watchdog'.

Author: Ondrej Zajicek <[email protected]>
Date:   Tue Sep 14 02:47:28 2010 +0200

watchdog: it87_wdt: Add support for IT8720F watchdog

This simple patch adds support for a watchdog in IT8720F Super IO chip to it87_wdt driver.

Author: Joe Perches <[email protected]>
Date:   Mon Sep 13 21:23:59 2010 -0700

watchdog: Use static const char * const where possible

Author: Prarit Bhargava <[email protected]>
Date:   Fri Aug 6 11:41:24 2010 -0400

watchdog: iTCO_wdt: Cleanup warning messages

The current iTCO_wdt driver warnings are confusing. Currently when the device driver returns an error the console contains:

iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected

After the patch,

iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS

Clean this up and use the word "device" to describe the device.

Author: Seth Heasley <[email protected]>
Date:   Thu Sep 9 09:58:03 2010 -0700

watchdog: iTCO_wdt: TCO Watchdog patch for Intel Patsburg DeviceIDs

This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog.

The Changes can also be looked at on:

	http://www.kernel.org/git/?p=linux/kernel/git/wim/linux-2.6-watchdog.git;a=summary

For completeness, I added the overal diff below.

Greetings,
Wim.

================================================================================

drivers/watchdog/Kconfig +17 -6
index c356146..4a29104 100644
@@ -409,11 +409,11 @@ config ALIM7101_WDT
 	  Most people will say N.
 
 config F71808E_WDT
-	tristate "Fintek F71808E and F71882FG Watchdog"
+	tristate "Fintek F71808E, F71882FG and F71889FG Watchdog"
 	depends on X86 && EXPERIMENTAL
 	help
 	  This is the driver for the hardware watchdog on the Fintek
-	  F71808E and F71882FG Super I/O controllers.
+	  F71808E, F71882FG and F71889FG Super I/O controllers.
 
 	  You can compile this driver directly into the kernel, or use
 	  it as a module.  The module will be called f71808e_wdt.
@@ -565,10 +565,11 @@ config IT87_WDT
 	tristate "IT87 Watchdog Timer"
 	depends on X86 && EXPERIMENTAL
 	---help---
-	  This is the driver for the hardware watchdog on the ITE IT8716,
-	  IT8718, IT8726, IT8712(Version J,K) Super I/O chips. This watchdog
-	  simply watches your kernel to make sure it doesn't freeze, and if
-	  it does, it reboots your computer after a certain amount of time.
+	  This is the driver for the hardware watchdog on the ITE IT8702,
+	  IT8712, IT8716, IT8718, IT8720, IT8726, IT8712 Super I/O chips.
+	  This watchdog simply watches your kernel to make sure it doesn't
+	  freeze, and if it does, it reboots your computer after a certain
+	  amount of time.
 
 	  To compile this driver as a module, choose M here: the module will
 	  be called it87_wdt.
@@ -916,6 +917,16 @@ config OCTEON_WDT
 	  from the first interrupt, it is then only poked when the
 	  device is written.
 
+config BCM63XX_WDT
+	tristate "Broadcom BCM63xx hardware watchdog"
+	depends on BCM63XX
+	help
+	  Watchdog driver for the built in watchdog hardware in Broadcom
+	  BCM63xx SoC.
+
+	  To compile this driver as a loadable module, choose M here.
+	  The module will be called bcm63xx_wdt.
+
 # PARISC Architecture
 
 # POWERPC Architecture
drivers/watchdog/Makefile +1 -0
index 8374503..4b0ef38 100644
@@ -109,6 +109,7 @@ obj-$(CONFIG_SBC_EPX_C3_WATCHDOG) += sbc_epx_c3.o
 
 # MIPS Architecture
 obj-$(CONFIG_BCM47XX_WDT) += bcm47xx_wdt.o
+obj-$(CONFIG_BCM63XX_WDT) += bcm63xx_wdt.o
 obj-$(CONFIG_RC32434_WDT) += rc32434_wdt.o
 obj-$(CONFIG_INDYDOG) += indydog.o
 obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
drivers/watchdog/bcm63xx_wdt.c new file +350 -0

350 lines not on this page · raw message

drivers/watchdog/f71808e_wdt.c +9 -1
index 7e5c266..65e5796 100644
@@ -308,6 +308,12 @@ static int watchdog_start(void)
 		superio_set_bit(watchdog.sioaddr, 0x29, 1);
 		break;
 
+	case f71889fg:
+		/* set pin 40 to WDTRST# */
+		superio_outb(watchdog.sioaddr, 0x2b,
+				superio_inb(watchdog.sioaddr, 0x2b) & 0xcf);
+		break;
+
 	default:
 		/*
 		 * 'default' label to shut up the compiler and catch
@@ -708,8 +714,10 @@ static int __init f71808e_find(int sioaddr)
 	case SIO_F71882_ID:
 		watchdog.type = f71882fg;
 		break;
-	case SIO_F71862_ID:
 	case SIO_F71889_ID:
+		watchdog.type = f71889fg;
+		break;
+	case SIO_F71862_ID:
 		/* These have a watchdog, though it isn't implemented (yet). */
 		err = -ENOSYS;
 		goto exit;
drivers/watchdog/iTCO_wdt.c +15 -11
index 69de871..f7e90fe 100644
@@ -146,6 +146,7 @@ enum iTCO_chipsets {
 	TCO_CPT29,	/* Cougar Point */
 	TCO_CPT30,	/* Cougar Point */
 	TCO_CPT31,	/* Cougar Point */
+	TCO_PBG,	/* Patsburg */
 };
 
 static struct {
@@ -233,6 +234,7 @@ static struct {
 	{"Cougar Point", 2},
 	{"Cougar Point", 2},
 	{"Cougar Point", 2},
+	{"Patsburg", 2},
 	{NULL, 0}
 };
 
@@ -348,6 +350,7 @@ static struct pci_device_id iTCO_wdt_pci_tbl[] = {
 	{ ITCO_PCI_DEVICE(0x1c5d,				TCO_CPT29)},
 	{ ITCO_PCI_DEVICE(0x1c5e,				TCO_CPT30)},
 	{ ITCO_PCI_DEVICE(0x1c5f,				TCO_CPT31)},
+	{ ITCO_PCI_DEVICE(0x1d40,				TCO_PBG)},
 	{ 0, },			/* End of list */
 };
 MODULE_DEVICE_TABLE(pci, iTCO_wdt_pci_tbl);
@@ -374,7 +377,7 @@ static char expect_release;
 static struct {		/* this is private data for the iTCO_wdt device */
 	/* TCO version/generation */
 	unsigned int iTCO_version;
-	/* The cards ACPIBASE address (TCOBASE = ACPIBASE+0x60) */
+	/* The device's ACPIBASE address (TCOBASE = ACPIBASE+0x60) */
 	unsigned long ACPIBASE;
 	/* NO_REBOOT flag is Memory-Mapped GCS register bit 5 (TCO version 2)*/
 	unsigned long __iomem *gcs;
@@ -467,7 +470,7 @@ static int iTCO_wdt_start(void)
 	if (iTCO_wdt_unset_NO_REBOOT_bit()) {
 		spin_unlock(&iTCO_wdt_private.io_lock);
 		printk(KERN_ERR PFX "failed to reset NO_REBOOT flag, "
-					"reboot disabled by hardware\n");
+					"reboot disabled by hardware/BIOS\n");
 		return -EIO;
 	}
 
@@ -781,8 +784,8 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	base_address &= 0x0000ff80;
 	if (base_address == 0x00000000) {
 		/* Something's wrong here, ACPIBASE has to be set */
-		printk(KERN_ERR PFX "failed to get TCOBASE address\n");
-		pci_dev_put(pdev);
+		printk(KERN_ERR PFX "failed to get TCOBASE address, "
+					"device disabled by hardware/BIOS\n");
 		return -ENODEV;
 	}
 	iTCO_wdt_private.iTCO_version =
@@ -797,7 +800,8 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	if (iTCO_wdt_private.iTCO_version == 2) {
 		pci_read_config_dword(pdev, 0xf0, &base_address);
 		if ((base_address & 1) == 0) {
-			printk(KERN_ERR PFX "RCBA is disabled by hardware\n");
+			printk(KERN_ERR PFX "RCBA is disabled by hardware"
+						"/BIOS, device disabled\n");
 			ret = -ENODEV;
 			goto out;
 		}
@@ -808,7 +812,7 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	/* Check chipset's NO_REBOOT bit */
 	if (iTCO_wdt_unset_NO_REBOOT_bit() && iTCO_vendor_check_noreboot_on()) {
 		printk(KERN_INFO PFX "unable to reset NO_REBOOT flag, "
-					"platform may have disabled it\n");
+					"device disabled by hardware/BIOS\n");
 		ret = -ENODEV;	/* Cannot reset NO_REBOOT bit */
 		goto out_unmap;
 	}
@@ -819,7 +823,8 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	/* The TCO logic uses the TCO_EN bit in the SMI_EN register */
 	if (!request_region(SMI_EN, 4, "iTCO_wdt")) {
 		printk(KERN_ERR PFX
-			"I/O address 0x%04lx already in use\n", SMI_EN);
+			"I/O address 0x%04lx already in use, "
+						"device disabled\n", SMI_EN);
 		ret = -EIO;
 		goto out_unmap;
 	}
@@ -831,8 +836,8 @@ static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
 	/* The TCO I/O registers reside in a 32-byte range pointed to
 	   by the TCOBASE value */
 	if (!request_region(TCOBASE, 0x20, "iTCO_wdt")) {
-		printk(KERN_ERR PFX "I/O address 0x%04lx already in use\n",
-			TCOBASE);
+		printk(KERN_ERR PFX "I/O address 0x%04lx already in use "
+						"device disabled\n", TCOBASE);
 		ret = -EIO;
 		goto unreg_smi_en;
 	}
@@ -880,7 +885,6 @@ out_unmap:
 	if (iTCO_wdt_private.iTCO_version == 2)
 		iounmap(iTCO_wdt_private.gcs);
 out:
-	pci_dev_put(iTCO_wdt_private.pdev);
 	iTCO_wdt_private.ACPIBASE = 0;
 	return ret;
 }
@@ -921,7 +925,7 @@ static int __devinit iTCO_wdt_probe(struct platform_device *dev)
 	}
 
 	if (!found)
-		printk(KERN_INFO PFX "No card detected\n");
+		printk(KERN_INFO PFX "No device detected.\n");
 
 	return ret;
 }
drivers/watchdog/it8712f_wdt.c +17 -8
index f52c162..b32c6c0 100644
@@ -75,15 +75,23 @@ static unsigned short address;
 #define WDT_CONFIG	0x72	/* WDT Register: Configuration */
 #define WDT_TIMEOUT	0x73	/* WDT Register: Timeout Value */
 
-#define WDT_RESET_GAME	0x10
-#define WDT_RESET_KBD	0x20
-#define WDT_RESET_MOUSE	0x40
-#define WDT_RESET_CIR	0x80
+#define WDT_RESET_GAME	0x10	/* Reset timer on read or write to game port */
+#define WDT_RESET_KBD	0x20	/* Reset timer on keyboard interrupt */
+#define WDT_RESET_MOUSE	0x40	/* Reset timer on mouse interrupt */
+#define WDT_RESET_CIR	0x80	/* Reset timer on consumer IR interrupt */
 
 #define WDT_UNIT_SEC	0x80	/* If 0 in MINUTES */
 
-#define WDT_OUT_PWROK	0x10
-#define WDT_OUT_KRST	0x40
+#define WDT_OUT_PWROK	0x10	/* Pulse PWROK on timeout */
+#define WDT_OUT_KRST	0x40	/* Pulse reset on timeout */
+
+static int wdt_control_reg = WDT_RESET_GAME;
+module_param(wdt_control_reg, int, 0);
+MODULE_PARM_DESC(wdt_control_reg, "Value to write to watchdog control "
+		"register. The default WDT_RESET_GAME resets the timer on "
+		"game port reads that this driver generates. You can also "
+		"use KBD, MOUSE or CIR if you have some external way to "
+		"generate those interrupts.");
 
 static int superio_inb(int reg)
 {
@@ -131,7 +139,8 @@ static inline void superio_exit(void)
 
 static inline void it8712f_wdt_ping(void)
 {
-	inb(address);
+	if (wdt_control_reg & WDT_RESET_GAME)
+		inb(address);
 }
 
 static void it8712f_wdt_update_margin(void)
@@ -170,7 +179,7 @@ static void it8712f_wdt_enable(void)
 	superio_enter();
 	superio_select(LDN_GPIO);
 
-	superio_outb(WDT_RESET_GAME, WDT_CONTROL);
+	superio_outb(wdt_control_reg, WDT_CONTROL);
 
 	it8712f_wdt_update_margin();
 
drivers/watchdog/it87_wdt.c +68 -28

224 lines not on this page · raw message

drivers/watchdog/machzwd.c +2 -2
index 2d118cf..9280350 100644
@@ -143,7 +143,7 @@ static unsigned long next_heartbeat;
 #ifndef ZF_DEBUG
 #	define dprintk(format, args...)
 #else
-#	define dprintk(format, args...) printk(KERN_DEBUG PFX
+#	define dprintk(format, args...) printk(KERN_DEBUG PFX \
 				":%s:%d: " format, __func__, __LINE__ , ## args)
 #endif
 
@@ -388,7 +388,7 @@ static struct notifier_block zf_notifier = {
 
 static void __init zf_show_action(int act)
 {
-	char *str[] = { "RESET", "SMI", "NMI", "SCI" };
+	static const char * const str[] = { "RESET", "SMI", "NMI", "SCI" };
 
 	printk(KERN_INFO PFX ": Watchdog using action = %s\n", str[act]);
 }