Skip to contentSkip to conversation

2.6.36.2 reliably panics in VFS

DISCUSSION Sarah Sharp 2 participants 2 messages Dec 13, 2010 2 messages not in the archive Memory management

lore
Share & tools
lore
#1 lore raw
In reply to a message not in the archive
Quoted 6 lines · Peter Steiner

Hi

compiled latest 2.6.36.2 but it reliably panics() my machine. It happens if I try to dd sda to sdb (backup) using xhci USB3.0 (conceptronic CUSB3EXC) but ALSO using native USB 2.0 ports on the machine - after 10-15 minutes of dd.

Can you run lspci -v and lsusb? I'm wondering if the USB 2.0 ports are part of an EHCI host controller or an xHCI host controller.

Quoted 3 lines

Please see attached screenshot (I cannot copy it as text as it takes down the machine and locks up in text console, so I can only make a foto).

Can you run netconsole to capture more of the messages before that? If you need help with setting up netconsole, see:

	http://sarah.thesharps.us/2010-03-26-09-41
Quoted 5 lines

see attached .config.

The bug did NOT happen on 2.6.35.7 - however there the USB3.0 xhci frequently disconnects the sdb backup disk and dd fails after 400GB of copy or so (but no panic).

Would this happen to be on a Lenovo W510 laptop? I've received reports of different oopses caused by disconnects, while running 2.6.35.8:

http://marc.info/?l=linux-kernel&m=129131271416325&w=2

Do you see panics or oopses when you run 2.6.35.8? Or did you just upgrade straight from 2.6.35.7 to 2.6.36.2?

Sarah Sharp

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to [email protected]. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom policy in Canada: sign http://dissolvethecrtc.ca/
Don't email: <a href=mailto:"[email protected]"> [email protected] </a>

#3 lore raw
In reply to a message not in the archive
Quoted 10 lines · Sarah Sharp
Quoted 6 lines · Peter Steiner

Hi

compiled latest 2.6.36.2 but it reliably panics() my machine. It happens if I try to dd sda to sdb (backup) using xhci USB3.0 (conceptronic CUSB3EXC) but ALSO using native USB 2.0 ports on the machine - after 10-15 minutes of dd.

Can you run lspci -v and lsusb? I'm wondering if the USB 2.0 ports are part of an EHCI host controller or an xHCI host controller.

USB 2.0 is built in controller, so they are EHCI.

The usb 3.0 ports are on a conceptronic CUSB3EXC ExpressCard expansion card as I already mentioned. I've the card not at hand now, so here lspci & lsusb WITHOUT the USB 3.0 card:

00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=09 <?> Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at e8400000 (32-bit, non-prefetchable) [size=512K] I/O ports at 6000 [size=8]
Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at e8480000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 2 Kernel driver in use: i915

00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0
Memory at e8500000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2

00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, fast devsel, latency 0, IRQ 41 Memory at e8580000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI
00
Capabilities: [100] Virtual Channel
Capabilities: [130] Root Complex Link
Kernel driver in use: HDA Intel

00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
        I/O behind bridge: 00007000-00007fff
        Memory behind bridge: e8000000-e80fffff
        Prefetchable memory behind bridge:

00000000cf800000-00000000cf9fffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link

00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 01) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=18, subordinate=18, sec-latency=0
        I/O behind bridge: 00004000-00005fff
        Memory behind bridge: e4000000-e7ffffff
        Prefetchable memory behind bridge:

00000000cfa00000-00000000cfbfffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link

00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 01) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
        I/O behind bridge: 00002000-00003fff
        Memory behind bridge: e0000000-e3ffffff
        Prefetchable memory behind bridge:

00000000cfc00000-00000000cfdfffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device
30aa
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link

00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 20 I/O ports at 6020 [size=32]
Kernel driver in use: uhci_hcd

00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 21 I/O ports at 6040 [size=32]
Kernel driver in use: uhci_hcd

00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at 6060 [size=32]
Kernel driver in use: uhci_hcd

00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at 6080 [size=32]
Kernel driver in use: uhci_hcd

00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0, IRQ 20 Memory at e8584000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
        I/O behind bridge: 00008000-00008fff
        Memory behind bridge: e8100000-e83fffff
        Prefetchable memory behind bridge:

00000000ec000000-00000000efffffff
Capabilities: [50] Subsystem: Hewlett-Packard Company Device
30aa

00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])

        Subsystem: Hewlett-Packard Company Device 30aa
        Flags: bus master, medium devsel, latency 0, IRQ 16
        I/O ports at 01f0 [size=8]
        I/O ports at 03f4 [size=1]
        I/O ports at 0170 [size=8]
        I/O ports at 0374 [size=1]
        I/O ports at 60a0 [size=16]
        Kernel driver in use: ata_piix

00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0])

        Subsystem: Hewlett-Packard Company Device 30aa
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 40
        I/O ports at 13f0 [size=8]
        I/O ports at 15f4 [size=4]
        I/O ports at 1370 [size=8]
        I/O ports at 1574 [size=4]
        I/O ports at 60d0 [size=16]
        Memory at e8585000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [70] Power Management version 2
        Kernel driver in use: ahci

02:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller

        Subsystem: Hewlett-Packard Company Device 30aa
        Flags: bus master, medium devsel, latency 168, IRQ 18
        Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: ec000000-effff000 (prefetchable)
        Memory window 1: f0000000-f3fff000
        I/O window 0: 00008000-000080ff
        I/O window 1: 00008400-000084ff
        16-bit legacy interface ports at 0001
        Kernel driver in use: yenta_cardbus

02:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 64, IRQ 19 Memory at e8108000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2 Kernel driver in use: tifm_7xx1

02:06.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at e8109000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2 Kernel driver in use: sdhci-pci

02:06.4 Communication controller: Texas Instruments PCIxx12 GemCore based SmartCard controller
Subsystem: Hewlett-Packard Company nc6310
Flags: medium devsel, IRQ 10
Memory at e810a000 (32-bit, non-prefetchable) [size=4K] Memory at e810b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2

02:0e.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
Subsystem: Hewlett-Packard Company Device 30aa
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e8110000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+ Kernel driver in use: tg3

08:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Subsystem: Hewlett-Packard Company Compaq 6710b or nx9420
Notebook
Flags: bus master, fast devsel, latency 0, IRQ 11 Memory at e8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [e0] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 00-1b-77-ff-ff-70-85-a0

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.36.2 ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:00:1d.7
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 8
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect Port 2: 0000.0100 power
Port 3: 0000.0503 highspeed power enable connect Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Bus 001 Device 002: ID 0424:2503 Standard Microsystems Corp. USB 2.0 Hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         2 TT per port
  bMaxPacketSize0        64
  idVendor           0x0424 Standard Microsystems Corp.
  idProduct          0x2503 USB 2.0 Hub
  bcdDevice            0.01
  iManufacturer           0 
  iProduct                0 
  iSerial                 0 
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 1 Single TT
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 2 TT per port
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 1 milli Ampere
DeviceRemovable 0x0e
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Port 3: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub

bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered

Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00

  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0bda Realtek Semiconductor Corp.
  idProduct          0x8187 RTL8187 Wireless Adapter
  bcdDevice            1.00
  iManufacturer           1 Manufacturer_Realtek_RTL8187_
  iProduct                2 RTL8187_Wireless_LAN_Adapter
  iSerial                 3 00C0CA1B8330
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 Wireless Network Card
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 5 Bulk-IN,Bulk-OUT,Bulk-OUT
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00

  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 

bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

Bus 001 Device 004: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass       255 Vendor Specific Subclass
  bDeviceProtocol       255 Vendor Specific Protocol
  bMaxPacketSize0         8
  idVendor           0x08ff AuthenTec, Inc.
  idProduct          0x2580 AES2501 Fingerprint Sensor
  bcdDevice            6.23
  iManufacturer           0 
  iProduct                1 Fingerprint Sensor
  iSerial                 0 
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.36.2 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.0
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.36.2 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.1
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.36.2 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.2
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10

  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.36.2 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.3
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

Quoted 9 lines
Quoted 4 lines

Please see attached screenshot (I cannot copy it as text as it takes down the machine and locks up in text console, so I can only make a foto).

Can you run netconsole to capture more of the messages before that? If you need help with setting up netconsole, see:

	http://sarah.thesharps.us/2010-03-26-09-41

I'm afraid I lack the time to play with kernel setup... :(

Quoted 6 lines
Quoted 5 lines

see attached .config.

The bug did NOT happen on 2.6.35.7 - however there the USB3.0 xhci frequently disconnects the sdb backup disk and dd fails after 400GB of copy or so (but no panic).

Quoted 7 lines

Would this happen to be on a Lenovo W510 laptop? I've received reports of different oopses caused by disconnects, while running 2.6.35.8:

http://marc.info/?l=linux-kernel&m=129131271416325&w=2

Do you see panics or oopses when you run 2.6.35.8? Or did you just upgrade straight from 2.6.35.7 to 2.6.36.2?

upgraded from 2.6.35.7 to 2.6.36 => panics
so then upgraded from 2.6.36 to 2.6.36.2 => same panic() while dd

As I said this happens equally if I connect my backup station to either native USB 2.0 (USB3.0 NOT plugged in!) or the conceptronics USB 3.0. The backup station is Sharkoon SATA Quickport 3.0.

Hope this helps.

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to [email protected]. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Fight unfair telecom policy in Canada: sign http://dissolvethecrtc.ca/
Don't email: <a href=mailto:"[email protected]"> [email protected] </a>