Skip to contentSkip to conversation

HDMI monitor hot remove handling

DISCUSSION Wu Fengguang 2 participants 3 messages Nov 11, 2011 – Nov 14, 2011 9 messages not in the archive

Subsystems (3)
lore
Share & tools
lore
#9 lore raw
In reply to a message not in the archive
Quoted 10 lines
Quoted 3 lines
Quoted 3 lines

I still think you should do those in hot_plug(), to call detect() for current status, write eld and set specific audio enable/disable bit for all audio stuff. Just my sense, you may send RFC patch for other's comment.

yeah, mode_set() will only be in normal mode setting path and taking current monitor's audio capability, but not on hot removal path. And if connector's DPMS off, does audio need to care? I think no, as user might still like to hear sound, right? ;)

So looks currently nobody cares for hot removal, you need to set that by yourself somewhere.

Zhenyu, according to your comments, here is the patch, tested OK on HDMI :) DP not tested yet.

This notifies the audio driver of the HDMI/DP monitor hot removal event.

- clear SDVO_AUDIO_ENABLE/DP_AUDIO_OUTPUT_ENABLE
- clear ELD Valid bit

---
 drivers/gpu/drm/drm_crtc_helper.c |    4 ++++
 drivers/gpu/drm/i915/intel_dp.c   |   19 +++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h  |    4 ++++
 drivers/gpu/drm/i915/intel_hdmi.c |   17 +++++++++++++++++
 include/drm/drm_crtc.h            |    1 +
 5 files changed, 45 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +19 -0
@@ -1984,6 +1984,24 @@ intel_dp_detect(struct drm_connector *co
 	return connector_status_connected;
 }
 
+static void intel_dp_hot_remove(struct drm_connector *connector)
+{
+	struct intel_dp *intel_dp = intel_attached_dp(connector);
+	struct drm_device *dev = intel_dp->base.base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct drm_crtc *crtc = intel_dp->base.base.crtc;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+
+	intel_dp->DP &= ~DP_AUDIO_OUTPUT_ENABLE;
+	I915_WRITE(intel_dp->output_reg, intel_dp->DP);
+	POSTING_READ(intel_dp->output_reg);
+	intel_wait_for_vblank(dev, intel_crtc->pipe);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector, crtc);
+}
+
 static int intel_dp_get_modes(struct drm_connector *connector)
 {
 	struct intel_dp *intel_dp = intel_attached_dp(connector);
@@ -2143,6 +2161,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_dp_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_dp_set_property,
+	.hot_remove = intel_dp_hot_remove,
 	.destroy = intel_dp_destroy,
 };
 
drivers/gpu/drm/i915/intel_drv.h +4 -0
@@ -382,6 +382,10 @@ extern void intel_fb_restore_mode(struct
 extern void intel_init_clock_gating(struct drm_device *dev);
 extern void intel_write_eld(struct drm_encoder *encoder,
 			    struct drm_display_mode *mode);
+extern void intel_hotplug_status(struct drm_device *dev,
+			  struct drm_connector *connector,
+			  struct drm_crtc *crtc,
+			  enum drm_connector_status status);
 extern void intel_cpt_verify_modeset(struct drm_device *dev, int pipe);
 
 #endif /* __INTEL_DRV_H__ */
drivers/gpu/drm/i915/intel_hdmi.c +17 -0
@@ -352,6 +352,22 @@ intel_hdmi_detect(struct drm_connector *
 	return status;
 }
 
+static void intel_hdmi_hot_remove(struct drm_connector *connector)
+{
+	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	u32 temp;
+
+	temp = I915_READ(intel_hdmi->sdvox_reg);
+	I915_WRITE(intel_hdmi->sdvox_reg, temp & ~SDVO_AUDIO_ENABLE);
+	POSTING_READ(intel_hdmi->sdvox_reg);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector,
+					    intel_hdmi->base.base.crtc);
+}
+
 static int intel_hdmi_get_modes(struct drm_connector *connector)
 {
 	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
@@ -461,6 +477,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_hdmi_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_hdmi_set_property,
+	.hot_remove = intel_hdmi_hot_remove,
 	.destroy = intel_hdmi_destroy,
 };
 
drivers/gpu/drm/drm_crtc_helper.c +4 -0
@@ -907,6 +907,10 @@ static void output_poll_execute(struct w
 			      old_status, connector->status);
 		if (old_status != connector->status)
 			changed = true;
+		if (old_status == connector_status_connected &&
+		    connector->status == connector_status_disconnected)
+			connector->funcs->hot_remove(connector);
+
 	}
 
 	mutex_unlock(&dev->mode_config.mutex);
include/drm/drm_crtc.h +1 -0
@@ -419,6 +419,7 @@ struct drm_connector_funcs {
 	int (*fill_modes)(struct drm_connector *connector, uint32_t max_width, uint32_t max_height);
 	int (*set_property)(struct drm_connector *connector, struct drm_property *property,
 			     uint64_t val);
+	void (*hot_remove)(struct drm_connector *connector);
 	void (*destroy)(struct drm_connector *connector);
 	void (*force)(struct drm_connector *connector);
 };
#10 lore raw
Quoted 8 lines · Wu Fengguang
Quoted 8 lines
Quoted 3 lines
Quoted 3 lines

I still think you should do those in hot_plug(), to call detect() for current status, write eld and set specific audio enable/disable bit for all audio stuff. Just my sense, you may send RFC patch for other's comment.

yeah, mode_set() will only be in normal mode setting path and taking current monitor's audio capability, but not on hot removal path. And if connector's DPMS off, does audio need to care? I think no, as user might still like to hear sound, right? ;)

Quoted 5 lines
Quoted 2 lines

So looks currently nobody cares for hot removal, you need to set that by yourself somewhere.

Zhenyu, according to your comments, here is the patch, tested OK on HDMI :) DP not tested yet.

Well, I don't think I suggested a new hook for hot removal. ;)

You know that hot_plug() hook is intel encoder thing, which is the place I think you can do audio config stuff.

Quoted 120 lines

This notifies the audio driver of the HDMI/DP monitor hot removal event.

- clear SDVO_AUDIO_ENABLE/DP_AUDIO_OUTPUT_ENABLE
- clear ELD Valid bit

---
 drivers/gpu/drm/drm_crtc_helper.c |    4 ++++
 drivers/gpu/drm/i915/intel_dp.c   |   19 +++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h  |    4 ++++
 drivers/gpu/drm/i915/intel_hdmi.c |   17 +++++++++++++++++
 include/drm/drm_crtc.h            |    1 +
 5 files changed, 45 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +19 -0
@@ -1984,6 +1984,24 @@ intel_dp_detect(struct drm_connector *co
 	return connector_status_connected;
 }
 
+static void intel_dp_hot_remove(struct drm_connector *connector)
+{
+	struct intel_dp *intel_dp = intel_attached_dp(connector);
+	struct drm_device *dev = intel_dp->base.base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct drm_crtc *crtc = intel_dp->base.base.crtc;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+
+	intel_dp->DP &= ~DP_AUDIO_OUTPUT_ENABLE;
+	I915_WRITE(intel_dp->output_reg, intel_dp->DP);
+	POSTING_READ(intel_dp->output_reg);
+	intel_wait_for_vblank(dev, intel_crtc->pipe);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector, crtc);
+}
+
 static int intel_dp_get_modes(struct drm_connector *connector)
 {
 	struct intel_dp *intel_dp = intel_attached_dp(connector);
@@ -2143,6 +2161,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_dp_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_dp_set_property,
+	.hot_remove = intel_dp_hot_remove,
 	.destroy = intel_dp_destroy,
 };
 
drivers/gpu/drm/i915/intel_drv.h +4 -0
@@ -382,6 +382,10 @@ extern void intel_fb_restore_mode(struct
 extern void intel_init_clock_gating(struct drm_device *dev);
 extern void intel_write_eld(struct drm_encoder *encoder,
 			    struct drm_display_mode *mode);
+extern void intel_hotplug_status(struct drm_device *dev,
+			  struct drm_connector *connector,
+			  struct drm_crtc *crtc,
+			  enum drm_connector_status status);
 extern void intel_cpt_verify_modeset(struct drm_device *dev, int pipe);
 
 #endif /* __INTEL_DRV_H__ */
drivers/gpu/drm/i915/intel_hdmi.c +17 -0
@@ -352,6 +352,22 @@ intel_hdmi_detect(struct drm_connector *
 	return status;
 }
 
+static void intel_hdmi_hot_remove(struct drm_connector *connector)
+{
+	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	u32 temp;
+
+	temp = I915_READ(intel_hdmi->sdvox_reg);
+	I915_WRITE(intel_hdmi->sdvox_reg, temp & ~SDVO_AUDIO_ENABLE);
+	POSTING_READ(intel_hdmi->sdvox_reg);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector,
+					    intel_hdmi->base.base.crtc);
+}
+
 static int intel_hdmi_get_modes(struct drm_connector *connector)
 {
 	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
@@ -461,6 +477,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_hdmi_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_hdmi_set_property,
+	.hot_remove = intel_hdmi_hot_remove,
 	.destroy = intel_hdmi_destroy,
 };
 
drivers/gpu/drm/drm_crtc_helper.c +4 -0
@@ -907,6 +907,10 @@ static void output_poll_execute(struct w
 			      old_status, connector->status);
 		if (old_status != connector->status)
 			changed = true;
+		if (old_status == connector_status_connected &&
+		    connector->status == connector_status_disconnected)
+			connector->funcs->hot_remove(connector);
+
 	}
 
 	mutex_unlock(&dev->mode_config.mutex);
include/drm/drm_crtc.h +1 -0
@@ -419,6 +419,7 @@ struct drm_connector_funcs {
 	int (*fill_modes)(struct drm_connector *connector, uint32_t max_width, uint32_t max_height);
 	int (*set_property)(struct drm_connector *connector, struct drm_property *property,
 			     uint64_t val);
+	void (*hot_remove)(struct drm_connector *connector);
 	void (*destroy)(struct drm_connector *connector);
 	void (*force)(struct drm_connector *connector);
 };
Signature · 3 lines
Open Source Technology Center, Intel ltd.

$gpg --keyserver wwwkeys.pgp.net --recv-keys 4D781827

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#11 lore raw
Quoted 9 lines · Zhenyu Wang
Quoted 8 lines · Wu Fengguang
Quoted 8 lines
Quoted 3 lines
Quoted 3 lines

I still think you should do those in hot_plug(), to call detect() for current status, write eld and set specific audio enable/disable bit for all audio stuff. Just my sense, you may send RFC patch for other's comment.

yeah, mode_set() will only be in normal mode setting path and taking current monitor's audio capability, but not on hot removal path. And if connector's DPMS off, does audio need to care? I think no, as user might still like to hear sound, right? ;)

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

So looks currently nobody cares for hot removal, you need to set that by yourself somewhere.

Zhenyu, according to your comments, here is the patch, tested OK on HDMI :) DP not tested yet.

Well, I don't think I suggested a new hook for hot removal. ;)

Yes, sorry.

Quoted 2 lines

You know that hot_plug() hook is intel encoder thing, which is the place I think you can do audio config stuff.

The problem is, ->hot_plug() is called at the very beginning, before ->detect() is called. If doing the hot remove notifications in ->hot_plug(), the patch will add an _extra_ loop to call into ->detect().

Why not insert the functionalities somewhere after ->detect() is called and we already know it's a hot removal event? That avoids adding duplicate ->detect() calls.

Thanks,
Fengguang

Quoted 125 lines
Quoted 120 lines

This notifies the audio driver of the HDMI/DP monitor hot removal event.

- clear SDVO_AUDIO_ENABLE/DP_AUDIO_OUTPUT_ENABLE
- clear ELD Valid bit

---
 drivers/gpu/drm/drm_crtc_helper.c |    4 ++++
 drivers/gpu/drm/i915/intel_dp.c   |   19 +++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h  |    4 ++++
 drivers/gpu/drm/i915/intel_hdmi.c |   17 +++++++++++++++++
 include/drm/drm_crtc.h            |    1 +
 5 files changed, 45 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +19 -0
@@ -1984,6 +1984,24 @@ intel_dp_detect(struct drm_connector *co
 	return connector_status_connected;
 }
 
+static void intel_dp_hot_remove(struct drm_connector *connector)
+{
+	struct intel_dp *intel_dp = intel_attached_dp(connector);
+	struct drm_device *dev = intel_dp->base.base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct drm_crtc *crtc = intel_dp->base.base.crtc;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+
+	intel_dp->DP &= ~DP_AUDIO_OUTPUT_ENABLE;
+	I915_WRITE(intel_dp->output_reg, intel_dp->DP);
+	POSTING_READ(intel_dp->output_reg);
+	intel_wait_for_vblank(dev, intel_crtc->pipe);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector, crtc);
+}
+
 static int intel_dp_get_modes(struct drm_connector *connector)
 {
 	struct intel_dp *intel_dp = intel_attached_dp(connector);
@@ -2143,6 +2161,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_dp_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_dp_set_property,
+	.hot_remove = intel_dp_hot_remove,
 	.destroy = intel_dp_destroy,
 };
 
drivers/gpu/drm/i915/intel_drv.h +4 -0
@@ -382,6 +382,10 @@ extern void intel_fb_restore_mode(struct
 extern void intel_init_clock_gating(struct drm_device *dev);
 extern void intel_write_eld(struct drm_encoder *encoder,
 			    struct drm_display_mode *mode);
+extern void intel_hotplug_status(struct drm_device *dev,
+			  struct drm_connector *connector,
+			  struct drm_crtc *crtc,
+			  enum drm_connector_status status);
 extern void intel_cpt_verify_modeset(struct drm_device *dev, int pipe);
 
 #endif /* __INTEL_DRV_H__ */
drivers/gpu/drm/i915/intel_hdmi.c +17 -0
@@ -352,6 +352,22 @@ intel_hdmi_detect(struct drm_connector *
 	return status;
 }
 
+static void intel_hdmi_hot_remove(struct drm_connector *connector)
+{
+	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	u32 temp;
+
+	temp = I915_READ(intel_hdmi->sdvox_reg);
+	I915_WRITE(intel_hdmi->sdvox_reg, temp & ~SDVO_AUDIO_ENABLE);
+	POSTING_READ(intel_hdmi->sdvox_reg);
+
+	connector->eld[0] = 0;
+	if (dev_priv->display.write_eld)
+		dev_priv->display.write_eld(connector,
+					    intel_hdmi->base.base.crtc);
+}
+
 static int intel_hdmi_get_modes(struct drm_connector *connector)
 {
 	struct intel_hdmi *intel_hdmi = intel_attached_hdmi(connector);
@@ -461,6 +477,7 @@ static const struct drm_connector_funcs 
 	.detect = intel_hdmi_detect,
 	.fill_modes = drm_helper_probe_single_connector_modes,
 	.set_property = intel_hdmi_set_property,
+	.hot_remove = intel_hdmi_hot_remove,
 	.destroy = intel_hdmi_destroy,
 };
 
drivers/gpu/drm/drm_crtc_helper.c +4 -0
@@ -907,6 +907,10 @@ static void output_poll_execute(struct w
 			      old_status, connector->status);
 		if (old_status != connector->status)
 			changed = true;
+		if (old_status == connector_status_connected &&
+		    connector->status == connector_status_disconnected)
+			connector->funcs->hot_remove(connector);
+
 	}
 
 	mutex_unlock(&dev->mode_config.mutex);
include/drm/drm_crtc.h +1 -0
@@ -419,6 +419,7 @@ struct drm_connector_funcs {
 	int (*fill_modes)(struct drm_connector *connector, uint32_t max_width, uint32_t max_height);
 	int (*set_property)(struct drm_connector *connector, struct drm_property *property,
 			     uint64_t val);
+	void (*hot_remove)(struct drm_connector *connector);
 	void (*destroy)(struct drm_connector *connector);
 	void (*force)(struct drm_connector *connector);
 };
Signature · 3 lines
Open Source Technology Center, Intel ltd.

$gpg --keyserver wwwkeys.pgp.net --recv-keys 4D781827