Skip to contentSkip to conversation

ethernet-related thermal emergency on Thinkpad x60

DISCUSSION Pavel Machek 3 participants 3 messages Jul 4, 2012 x86 platform drivers

lore
Share & tools
lore
#0 lore raw

Hi!

When using nework interface (eth0), machine starts to behave weird. Like... complete freeze, then poweroff, then it hangs on boot (initializing ACPI) until I let it to cool down... and I'm not even using gigabit speed.

Did anyone see it? Any ideas? Should I attempt to open it and clean the dust?

Pavel

e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
coda_read_super: Bad mount data
coda_read_super: device index: 0
coda_read_super: rootfid is (01234567.ffffffff.08051c00.00000000)
coda: Unexpected interruption.
Failure of coda_cnode_make for root: error -4
thinkpad_acpi: THERMAL EMERGENCY: a sensor reports something is extremely hot!
thinkpad_acpi: temperatures (Celsius): 88 49 N/A 82 40 N/A 40 N/A 52 61 N/A N/A N/A N/A N/A N/A

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#1 lore raw
Quoted 6 lines · Pavel Machek

Hi!

When using nework interface (eth0), machine starts to behave weird. Like... complete freeze, then poweroff, then it hangs on boot (initializing ACPI) until I let it to cool down... and I'm not even using gigabit speed.

Hi Pavel.

Please could you clarify why you believe that this is related to Ethernet? I.e. does the problem not happen when you're not using Ethernet (but rather wifi or no networking at all)?

Does the problem start to happen when you plug in the Ethernet cable, having previously booted the machine without being connected to the network?

Where does the CPU spend its time when the problem occurs?

Basic question: does your CPU fan work? Nothing is obstructing the airflow (e.g. dust)? If you're using fancontrol in order to regulate the fan speed, it is set up properly to prevent overheating?

HTH, Jan

#2 lore raw
In reply to Pavel Machek
Quoted 7 lines · Pavel Machek

When using nework interface (eth0), machine starts to behave weird. Like... complete freeze, then poweroff, then it hangs on boot (initializing ACPI) until I let it to cool down... and I'm not even using gigabit speed.

Did anyone see it? Any ideas? Should I attempt to open it and clean the dust?

Opening it up and cleaning things is always a good idea. Some intel boxes have the GbEth MAC inside the chipset, so it is also worth checking whether the thermal contact between heatsink and chipset is operating properly (or just replace the old thermal compounts with Artic Silver 5 or some other non-reactive, extremely high quality compound that is suitable for the rapid thermal cycles of laptops).

Quoted 2 lines

thinkpad_acpi: THERMAL EMERGENCY: a sensor reports something is extremely hot!
thinkpad_acpi: temperatures (Celsius): 88 49 N/A 82 40 N/A 40 N/A 52 61 N/A N/A N/A N/A N/A N/A

My guess is that the 82°C reading on the fourth sensor is the problem, althouhg the CPU is also quite hot. That sensor is usually the GPU, but if your thinkpad has an integrated GPU, it is likely to have been used for the northbridge/chipset.

It can also be a shortcircuity in the ethernet PHY (either the chip, or some of the analog auxiliary circuitry). This is repairable by an skilled surface-mount technician if he can get his hands in the schematics and source the replacement components, but if you ask Lenovo about it, they will want to replace your entire planar card (motherboard)...

Signature · 4 lines
  "One disk to rule them all, One disk to find them. One disk to bring
  them all and in the darkness grind them. In the Land of Redmond
  where the shadows lie." -- The Silicon Valley Tarot
  Henrique Holschuh