gpio: samsung: add devicetree init for s3c24xx arches
Subsystems (3)
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Until now the Exynos-SoC was the only Samsung-SoC supporting the GPIOs via the device tree. This patch implements dt-support for the s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
--- .../devicetree/bindings/gpio/gpio-samsung.txt | 38 ++++++++++++ drivers/gpio/gpio-samsung.c | 63 ++++++++++++++++++++ 2 files changed, 101 insertions(+), 0 deletions(-)
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +38 -0
@@ -39,3 +39,41 @@ Example: #gpio-cells = <4>; gpio-controller; }; + + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,s3c24xx-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier: + - Pin number: depending on the controller a number from 0 up to 15. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa: gpio-controller@56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + };
drivers/gpio/gpio-samsung.c +63 -0
75 lines not on this page · raw message
Signature · 1 line
1.7.2.3
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Hi Heiko,
Quoted 20 lines · Heiko St?bner
Until now the Exynos-SoC was the only Samsung-SoC supporting the GPIOs via the device tree. This patch implements dt-support for the s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
Signed-off-by Heiko Stuebner <[email protected]>--- .../devicetree/bindings/gpio/gpio-samsung.txt | 38 ++++++++++++ drivers/gpio/gpio-samsung.c | 63 ++++++++++++++++++++ 2 files changed, 101 insertions(+), 0 deletions(-)Documentation/devicetree/bindings/gpio/gpio-samsung.txt +0
-0
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 47
Quoted 9 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +6
-0@@ -39,3 +39,41 @@ Example: #gpio-cells = <4>; gpio-controller; }; + + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,s3c24xx-gpio".
This is debatable, but I would choose to be specific here and use "samsing,s3c2416-gpio". For instance, SoC's in s3c24xx family have differing value for pull none/down/up.
Quoted 6 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +6
-0+ +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual.
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 63
Quoted 10 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +10
-0+ <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier: + - Pin number: depending on the controller a number from 0 up to 15. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled.
As per s3c2416 user manual, 2 is used for Pull Up and 3 is listed as reserved value. Any particular reason to use 3 here for pull up and not 2 as per the user manual?
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 68
Quoted 5 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +5
-0+ Bit 16 (0x00010000) - Input is active low. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1.
It would be informative to add information about the 'mux function' cell here as well. Specifically, on how to handle the banks that have an extended GPxSEL register that allow additional pin function selection.
Quoted 93 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +11
-0+ +Example: + + gpa: gpio-controller at 56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + };drivers/gpio/gpio-samsung.c +63
-1@@ -938,6 +938,67 @@ static void __init samsung_gpiolib_add(struct samsung_gpio_chip *chip)s3c_gpiolib_track (chip); } +#if defined(CONFIG_PLAT_S3C24XX ) && defined(CONFIG_OF ) +static int s3c24xx_gpio_xlate (struct gpio_chip *gc, +const struct of_phandle_args *gpiospec,u32 *flags) +{ +unsigned int pin; + +if (WARN_ON (gc->of_gpio_n_cells <3 )) +return -EINVAL ; + +if (WARN_ON (gpiospec->args_count < gc->of_gpio_n_cells)) +return -EINVAL ; + +if (gpiospec->args[0 ] > gc->ngpio) +return -EINVAL ; + + pin = gc->base + gpiospec->args[0 ]; + +if (s3c_gpio_cfgpin (pin,S3C_GPIO_SFN (gpiospec->args[1 ]))) +pr_warn ("gpio_xlate: failed to set pin function\n" ); +if (s3c_gpio_setpull (pin, gpiospec->args[2 ] &0xffff )) +pr_warn ("gpio_xlate: failed to set pin pull up/down\n" ); + +if (flags) + *flags = gpiospec->args[2 ] >>16 ; + +return gpiospec->args[0 ]; +} + +static const struct of_device_id s3c24xx_gpio_dt_match[]__initdata = { + { .compatible ="samsung,s3c24xx-gpio" , }, + {} +}; + +static __init void s3c24xx_gpiolib_attach_ofnode (struct samsung_gpio_chip *chip, +u64 base,u64 offset) +{ +struct gpio_chip *gc = &chip->chip; +u64 address; + +if (!of_have_populated_dt ()) +return ; + + address = chip->base ? base + ((u32 )chip->base &0xfff ) : base + offset; + gc->of_node =of_find_matching_node_by_address (NULL , + s3c24xx_gpio_dt_match, address); +if (!gc->of_node) { +pr_info ("gpio: device tree node not found for gpio controller" +" with base address %08llx\n" , address); +return ; + } + gc->of_gpio_n_cells =3 ; + gc->of_xlate = s3c24xx_gpio_xlate; +} +#elif defined(CONFIG_PLAT_S3C24XX ) +static __init void s3c24xx_gpiolib_attach_ofnode (struct samsung_gpio_chip *chip, +u64 base,u64 offset) +{ +return ; +} +#endif /* defined(CONFIG_PLAT_S3C24XX) && defined(CONFIG_OF) */ +static void __init s3c24xx_gpiolib_add_chips (struct samsung_gpio_chip *chip,int nr_chips,void __iomem *base) {@@ -962,6 +1023,8 @@ static void __init s3c24xx_gpiolib_add_chips(struct samsung_gpio_chip *chip, gc->direction_output = samsung_gpiolib_2bit_output;samsung_gpiolib_add (chip); + +s3c24xx_gpiolib_attach_ofnode (chip,S3C24XX_PA_GPIO , i *0x10 ); } } --
Quoted 2 lines
1.7.2.3
Overall, this is patch looks fine.
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Hi Thomas,
thanks for your review:
Am Montag, 27. August 2012, 06:20:49 schrieb Thomas Abraham:
Quoted 31 lines
Hi Heiko,
Quoted 28 lines · Heiko St?bner
Until now the Exynos-SoC was the only Samsung-SoC supporting the GPIOs via the device tree. This patch implements dt-support for the s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
Signed-off-by Heiko Stuebner <[email protected]>---
.../devicetree/bindings/gpio/gpio-samsung.txt | 38 ++++++++++++ drivers/gpio/gpio-samsung.c | 63++++++++++++++++++++ 2 files changed, 101 insertions(+), 0 deletions(-)
(quoted diff) +0
-0
b/Documentation/devicetree/bindings/gpio/gpio-samsung.txtindex 5375625..ce6a7d4 100644Documentation/devicetree/bindings/gpio/gpio-samsung.txt +0
-0@@ -39,3 +39,41 @@ Example: #gpio-cells = <4>; gpio-controller; };
Quoted 11 lines
Quoted 7 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +6
-0+ + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be"samsung,s3c24xx-gpio".
This is debatable, but I would choose to be specific here and use "samsing,s3c2416-gpio". For instance, SoC's in s3c24xx family have differing value for pull none/down/up.
Hmmm, but the logic to drive the gpio controller is the same for all arches. The only difference is the number to use for the different pull up/down settings. So I think the "samsung,s3c24xx-gpio" is ok but the documentation should simply reflect the different pull settings.
Quoted 12 lines
Quoted 12 lines
+
+- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node]Documentation/devicetree/bindings/gpio/gpio-samsung.txt +5
-0+ [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier:
Quoted 8 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 63
Quoted 4 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +4
-0+ - Pin number: depending on the controller a number from 0 up to 15. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled.As per s3c2416 user manual, 2 is used for Pull Up and 3 is listed as reserved value. Any particular reason to use 3 here for pull up and not 2 as per the user manual?
Sorry, copy and paste error :-)
Quoted 10 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 68
Quoted 5 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +5
-0+ Bit 16 (0x00010000) - Input is active low. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1.It would be informative to add information about the 'mux function' cell here as well. Specifically, on how to handle the banks that have an extended GPxSEL register that allow additional pin function selection.
Will add a mux function description.
Until now I've never realised the existence of the GPxSEL registers, so thanks for the pointer :-).
But is this used in the driver at all? All the setcfg/getcfg functions in gpio-samsung.c only handle the GPxCON registers - I haven't found code to handle the GPxSEL registers at all. So my guess is that this was never implemented - or that I'm blind ;-) .
Quoted 106 lines
Quoted 106 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +11
-0+ +Example: + + gpa: gpio-controller at 56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + };drivers/gpio/gpio-samsung.c +3
-0@@ -938,6 +938,67 @@ static void __init samsung_gpiolib_add(struct samsung_gpio_chip *chip)s3c_gpiolib_track (chip ); } +#if defined(CONFIG_PLAT_S3C24XX ) && defined(CONFIG_OF ) +static int s3c24xx_gpio_xlate (struct gpio_chip *gc, + const struct of_phandle_args *gpiospec, u32*flags) +{
drivers/gpio/gpio-samsung.c +30
-0+unsigned int pin; + +if (WARN_ON (gc->of_gpio_n_cells <3 )) +return -EINVAL ; + +if (WARN_ON (gpiospec->args_count < gc->of_gpio_n_cells)) +return -EINVAL ; + +if (gpiospec->args[0 ] > gc->ngpio) +return -EINVAL ; + + pin = gc->base + gpiospec->args[0 ]; + +if (s3c_gpio_cfgpin (pin,S3C_GPIO_SFN (gpiospec->args[1 ]))) +pr_warn ("gpio_xlate: failed to set pin function\n" ); +if (s3c_gpio_setpull (pin, gpiospec->args[2 ] &0xffff )) +pr_warn ("gpio_xlate: failed to set pin pull up/down\n" ); + +if (flags) + *flags = gpiospec->args[2 ] >>16 ; + +return gpiospec->args[0 ]; +} + +static const struct of_device_id s3c24xx_gpio_dt_match[]__initdata = { + { .compatible ="samsung,s3c24xx-gpio" , }, + {} +}; + +static __init void s3c24xx_gpiolib_attach_ofnode(struct
samsung_gpio_chip*chip, +
u64 base, u64 offset) +{drivers/gpio/gpio-samsung.c +7
-0+struct gpio_chip *gc = &chip->chip; +u64 address; + +if (!of_have_populated_dt ()) +return ; + + address = chip->base ? base + ((u32)chip->base & 0xfff) : base +offset; +
gc->of_node= of_find_matching_node_by_address(NULL,drivers/gpio/gpio-samsung.c +3
-0+ s3c24xx_gpio_dt_match, address); +if (!gc->of_node) { + pr_info("gpio: device tree node not found for gpiocontroller" + " with base address %08llx\n",
address); + return;drivers/gpio/gpio-samsung.c +6
-0+ } + gc->of_gpio_n_cells =3 ; + gc->of_xlate = s3c24xx_gpio_xlate; +} +#elif defined(CONFIG_PLAT_S3C24XX) +static __init void s3c24xx_gpiolib_attach_ofnode(struct
samsung_gpio_chip*chip, +
u64 base, u64 offset) +{drivers/gpio/gpio-samsung.c +6
-0+ return; +} +#endif /* defined(CONFIG_PLAT_S3C24XX) && defined(CONFIG_OF) */ +static void __init s3c24xx_gpiolib_add_chips (struct samsung_gpio_chip *chip,int nr_chips,void __iomem *base) {@@ -962,6 +1023,8 @@ static void __init s3c24xx_gpiolib_add_chips(struct samsung_gpio_chip *chip, gc->direction_output = samsung_gpiolib_2bit_output;samsung_gpiolib_add (chip); + + s3c24xx_gpiolib_attach_ofnode(chip, S3C24XX_PA_GPIO, i *
0x10);}
Quoted 8 lines
Quoted 4 lines
}
--
1.7.2.3Overall, this is patch looks fine.
Reviewed-by Thomas Abraham <[email protected]>
Heiko
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Hi,
Quoted 9 lines · Heiko St?bner
Hi Thomas,
thanks for your review:
Hmmm, but the logic to drive the gpio controller is the same for all arches. The only difference is the number to use for the different pull up/down settings. So I think the "samsung,s3c24xx-gpio" is ok but the documentation should simply reflect the different pull settings.
Also s3c2410 and s3c2440 has different count of GPIOs. And that could be a problem on machines
with GPIO-expanders (h1940 machine)
Quoted 7 lines
Quoted 4 lines
It would be informative to add information about the 'mux function' cell here as well. Specifically, on how to handle the banks that have an extended GPxSEL register that allow additional pin function selection.
Will add a mux function description.
Quoted 7 lines
Until now I've never realised the existence of the GPxSEL registers, so thanks for the pointer :-).
But is this used in the driver at all? All the setcfg/getcfg functions in
gpio-samsung.conly handle the GPxCON registers - I haven't found code to handle the GPxSEL registers at all. So my guess is that this was never implemented - or that I'm blind ;-) .
There're no GPxSEL registers on s3c2410/s3c2440/s3c2442. Is it something s3c2412/sec2416 specific?
Regards
Vasily
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Hi Vasily,
Am Montag, 27. August 2012, 10:57:04 schrieb Vasily Khoruzhick:
Quoted 7 lines
Hi,
Quoted 4 lines · Heiko St?bner
Hi Thomas,
thanks for your review:
Quoted 8 lines
Quoted 4 lines
Hmmm, but the logic to drive the gpio controller is the same for all arches. The only difference is the number to use for the different pull up/down settings. So I think the "samsung,s3c24xx-gpio" is ok but the documentation should simply reflect the different pull settings.
Also s3c2410 and s3c2440 has different count of GPIOs. And that could be a problem on machines
with GPIO-expanders (h1940 machine)
I'm not sure I follow :-) .
The compatible property here only sets the mechanism on how to handle the gpios defined in the devicetree - here to use the s3c24xx-style. As you can see in gpio-samsung.c the handling is already unified for all the s3c24xx architectures.
The definition of what gpio banks exist is then done in the respective devicetree file for the individual SoC. And of course here one would have individual definitions, depending on the banks present.
For reference my quite empty s3c2416.dtsi file currently looks like:
/include/ "skeleton.dtsi"
/ {
compatible = "samsung,s3c2416";
cpus {
cpu at 0 {
compatible = "arm,arm926ejs";
};
};
gpio-controllers {
#address-cells = <1>;
#size-cells = <1>;
gpio-controller;
ranges;
gpa: gpio-controller at 56000000 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000000 0x10>;
#gpio-cells = <3>;
};
gpb: gpio-controller at 56000010 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000010 0x10>;
#gpio-cells = <3>;
};
gpc: gpio-controller at 56000020 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000020 0x10>;
#gpio-cells = <3>;
};
gpd: gpio-controller at 56000030 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000030 0x10>;
#gpio-cells = <3>;
};
gpe: gpio-controller at 56000040 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000040 0x10>;
#gpio-cells = <3>;
};
gpf: gpio-controller at 56000050 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000050 0x10>;
#gpio-cells = <3>;
};
gpg: gpio-controller at 56000060 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000060 0x10>;
#gpio-cells = <3>;
};
gph: gpio-controller at 56000070 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000070 0x10>;
#gpio-cells = <3>;
};
/* s3c2443 and later */
gpj: gpio-controller at 560000D0 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x560000D0 0x10>;
#gpio-cells = <3>;
};
gpk: gpio-controller at 560000E0 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x560000E0 0x10>;
#gpio-cells = <3>;
};
gpl: gpio-controller at 560000F0 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x560000F0 0x10>;
#gpio-cells = <3>;
};
gpm: gpio-controller at 56000100 {
compatible = "samsung,s3c24xx-gpio";
reg = <0x56000100 0x10>;
#gpio-cells = <3>;
};
};
};Other s3c24xx SoCs would of course need to define their own.
Quoted 10 lines
Quoted 10 lines
Quoted 4 lines
It would be informative to add information about the 'mux function' cell here as well. Specifically, on how to handle the banks that have an extended GPxSEL register that allow additional pin function selection.
Will add a mux function description.
Until now I've never realised the existence of the GPxSEL registers, so thanks for the pointer :-).
Quoted 7 lines
Quoted 4 lines
But is this used in the driver at all? All the setcfg/getcfg functions in
gpio-samsung.conly handle the GPxCON registers - I haven't found code to handle the GPxSEL registers at all. So my guess is that this was never implemented - or that I'm blind ;-) .There're no GPxSEL registers on s3c2410/s3c2440/s3c2442. Is it something s3c2412/sec2416 specific?
s3c2412 also does not have it ... it seems entirely specific to s3c2416/s3c2450 and as written also seems to be unused. So I would tend to ignore it for now :-) .
Heiko
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Quoted 107 lines · Heiko St?bner
Hi Vasily,
I'm not sure I follow :-) .
The compatible property here only sets the mechanism on how to handle the gpios defined in the devicetree - here to use the s3c24xx-style. As you can see in
gpio-samsung.cthe handling is already unified for all the s3c24xx architectures.The definition of what gpio banks exist is then done in the respective devicetree file for the individual SoC. And of course here one would have individual definitions, depending on the banks present.
For reference my quite empty
s3c2416.dtsifile currently looks like:/include/ "
skeleton.dtsi"/ { compatible = "samsung,s3c2416"; cpus { cpu at 0 { compatible = "arm,arm926ejs"; }; }; gpio-controllers { #address-cells = <1>; #size-cells = <1>; gpio-controller; ranges; gpa: gpio-controller at 56000000 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000000 0x10>; #gpio-cells = <3>; }; gpb: gpio-controller at 56000010 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000010 0x10>; #gpio-cells = <3>; }; gpc: gpio-controller at 56000020 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000020 0x10>; #gpio-cells = <3>; }; gpd: gpio-controller at 56000030 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000030 0x10>; #gpio-cells = <3>; }; gpe: gpio-controller at 56000040 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000040 0x10>; #gpio-cells = <3>; }; gpf: gpio-controller at 56000050 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000050 0x10>; #gpio-cells = <3>; }; gpg: gpio-controller at 56000060 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000060 0x10>; #gpio-cells = <3>; }; gph: gpio-controller at 56000070 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000070 0x10>; #gpio-cells = <3>; }; /* s3c2443 and later */ gpj: gpio-controller at 560000D0 { compatible = "samsung,s3c24xx-gpio"; reg = <0x560000D0 0x10>; #gpio-cells = <3>; }; gpk: gpio-controller at 560000E0 { compatible = "samsung,s3c24xx-gpio"; reg = <0x560000E0 0x10>; #gpio-cells = <3>; }; gpl: gpio-controller at 560000F0 { compatible = "samsung,s3c24xx-gpio"; reg = <0x560000F0 0x10>; #gpio-cells = <3>; }; gpm: gpio-controller at 56000100 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000100 0x10>; #gpio-cells = <3>; }; }; };
Quoted 1 line
Other s3c24xx SoCs would of course need to define their own.
I see. But how does it handle GPA bank (which is output-only, and GPACON differs a bit from GP{B-J}CON? And some banks has lower number (not 16) of GPIOs, like GPH.
Also, what would be value for S3C_GPIO_END?
Regards
Vasily
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
Am Montag, 27. August 2012, 11:51:27 schrieb Vasily Khoruzhick:
Quoted 54 lines · Heiko St?bner
Quoted 53 lines
Hi Vasily,
I'm not sure I follow :-) .
The compatible property here only sets the mechanism on how to handle the gpios defined in the devicetree - here to use the s3c24xx-style. As you can see in
gpio-samsung.cthe handling is already unified for all the s3c24xx architectures.The definition of what gpio banks exist is then done in the respective devicetree file for the individual SoC. And of course here one would have individual definitions, depending on the banks present.
For reference my quite empty
s3c2416.dtsifile currently looks like:/include/ "
skeleton.dtsi"/ {
compatible = "samsung,s3c2416"; cpus { cpu at 0 { compatible = "arm,arm926ejs"; }; }; gpio-controllers { #address-cells = <1>; #size-cells = <1>; gpio-controller; ranges; gpa: gpio-controller at 56000000 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000000 0x10>; #gpio-cells = <3>; }; gpb: gpio-controller at 56000010 { compatible = "samsung,s3c24xx-gpio"; reg = <0x56000010 0x10>; #gpio-cells = <3>; };
[ ... ]
Quoted 11 lines
Quoted 5 lines
};};
Other s3c24xx SoCs would of course need to define their own.
I see. But how does it handle GPA bank (which is output-only, and GPACON differs a bit from GP{B-J}CON? And some banks has lower number (not 16) of GPIOs, like GPH.
Also, what would be value for
S3C_GPIO_END?
The creation of the banks is still done in gpio-samsung.c and the special handling of bank-a is still sitting in the s3c24xx_gpios[] array there.
In general the gpios are still created completely like before and the devicetree information is only attached to them so that dt-devices can reference them.
As you can see in the original patch, after the respective chip got created in s3c24xx_gpiolib_add_chips, s3c24xx_gpiolib_attach_ofnode searches for the representation of it in the device tree and attaches this to the chip.
So nothing really changed, except that dt-devices can now reference gpios and if they do s3c24xx_gpio_xlate will get called to configure them with the target values from the dt.
Currently I'm also only using it in a mixed mode configuration [1], supplementing a normal machine file with some devices from the devicetree - especially as I still need to figure out, what to do about the interrupt controller.
Heiko
[1] https://github.com/mmind/linux-es600/blob/topic/es600-devel/arch/arm/boot/dts/s3c24xx-sg06.dts
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
In reply to Heiko StübnerQuoted 48 lines · Heiko St?bner
Hi Thomas,
thanks for your review:
Am Montag, 27. August 2012, 06:20:49 schrieb Thomas Abraham:
Quoted 31 lines
Hi Heiko,
Quoted 28 lines · Heiko St?bner
Until now the Exynos-SoC was the only Samsung-SoC supporting the GPIOs via the device tree. This patch implements dt-support for the s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
Signed-off-by Heiko Stuebner <[email protected]>---
.../devicetree/bindings/gpio/gpio-samsung.txt | 38 ++++++++++++ drivers/gpio/gpio-samsung.c | 63++++++++++++++++++++ 2 files changed, 101 insertions(+), 0 deletions(-)
(quoted diff) +0
-0
b/Documentation/devicetree/bindings/gpio/gpio-samsung.txtindex 5375625..ce6a7d4 100644Documentation/devicetree/bindings/gpio/gpio-samsung.txt +0
-0@@ -39,3 +39,41 @@ Example: #gpio-cells = <4>; gpio-controller; };Quoted 11 lines
Quoted 7 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +6
-0+ + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be"samsung,s3c24xx-gpio".
This is debatable, but I would choose to be specific here and use "samsing,s3c2416-gpio". For instance, SoC's in s3c24xx family have differing value for pull none/down/up.
Quoted 4 lines
Hmmm, but the logic to drive the gpio controller is the same for all arches. The only difference is the number to use for the different pull up/down settings. So I think the "samsung,s3c24xx-gpio" is ok but the documentation should simply reflect the different pull settings.
Ok.
Quoted 23 lines
Quoted 14 lines
Quoted 14 lines
+
+- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node]Documentation/devicetree/bindings/gpio/gpio-samsung.txt +5
-0+ [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier:Quoted 8 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 63
Quoted 4 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +4
-0+ - Pin number: depending on the controller a number from 0 up to 15. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled.As per s3c2416 user manual, 2 is used for Pull Up and 3 is listed as reserved value. Any particular reason to use 3 here for pull up and not 2 as per the user manual?
Quoted 1 line
Sorry, copy and paste error :-)
Ok.
Quoted 15 lines
Quoted 8 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt Example: · line 68
Quoted 7 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +5
-0+ Bit 16 (0x00010000) - Input is active low. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1.Quoted 4 lines
It would be informative to add information about the 'mux function' cell here as well. Specifically, on how to handle the banks that have an extended GPxSEL register that allow additional pin function selection.
Will add a mux function description.
Quoted 7 lines
Until now I've never realised the existence of the GPxSEL registers, so thanks for the pointer :-).
But is this used in the driver at all? All the setcfg/getcfg functions in
gpio-samsung.conly handle the GPxCON registers - I haven't found code to handle the GPxSEL registers at all. So my guess is that this was never implemented - or that I'm blind ;-) .
You are right, there is no code that is handling the GPxCON registers.
Thanks,
Thomas.
Quoted 119 lines
Quoted 108 lines
Quoted 108 lines
Documentation/devicetree/bindings/gpio/gpio-samsung.txt +11
-0+ +Example: + + gpa: gpio-controller at 56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + };drivers/gpio/gpio-samsung.c +3
-0@@ -938,6 +938,67 @@ static void __init samsung_gpiolib_add(struct samsung_gpio_chip *chip)s3c_gpiolib_track (chip ); } +#if defined(CONFIG_PLAT_S3C24XX ) && defined(CONFIG_OF ) +static int s3c24xx_gpio_xlate (struct gpio_chip *gc, + const struct of_phandle_args *gpiospec, u32*flags) +{
drivers/gpio/gpio-samsung.c +30
-0+unsigned int pin; + +if (WARN_ON (gc->of_gpio_n_cells <3 )) +return -EINVAL ; + +if (WARN_ON (gpiospec->args_count < gc->of_gpio_n_cells)) +return -EINVAL ; + +if (gpiospec->args[0 ] > gc->ngpio) +return -EINVAL ; + + pin = gc->base + gpiospec->args[0 ]; + +if (s3c_gpio_cfgpin (pin,S3C_GPIO_SFN (gpiospec->args[1 ]))) +pr_warn ("gpio_xlate: failed to set pin function\n" ); +if (s3c_gpio_setpull (pin, gpiospec->args[2 ] &0xffff )) +pr_warn ("gpio_xlate: failed to set pin pull up/down\n" ); + +if (flags) + *flags = gpiospec->args[2 ] >>16 ; + +return gpiospec->args[0 ]; +} + +static const struct of_device_id s3c24xx_gpio_dt_match[]__initdata = { + { .compatible ="samsung,s3c24xx-gpio" , }, + {} +}; + +static __init void s3c24xx_gpiolib_attach_ofnode(struct
samsung_gpio_chip*chip, +
u64 base, u64 offset) +{drivers/gpio/gpio-samsung.c +7
-0+struct gpio_chip *gc = &chip->chip; +u64 address; + +if (!of_have_populated_dt ()) +return ; + + address = chip->base ? base + ((u32)chip->base & 0xfff) : base +offset; +
gc->of_node= of_find_matching_node_by_address(NULL,drivers/gpio/gpio-samsung.c +3
-0+ s3c24xx_gpio_dt_match, address); +if (!gc->of_node) { + pr_info("gpio: device tree node not found for gpiocontroller" + " with base address %08llx\n",
address); + return;drivers/gpio/gpio-samsung.c +6
-0+ } + gc->of_gpio_n_cells =3 ; + gc->of_xlate = s3c24xx_gpio_xlate; +} +#elif defined(CONFIG_PLAT_S3C24XX) +static __init void s3c24xx_gpiolib_attach_ofnode(struct
samsung_gpio_chip*chip, +
u64 base, u64 offset) +{drivers/gpio/gpio-samsung.c +6
-0+ return; +} +#endif /* defined(CONFIG_PLAT_S3C24XX) && defined(CONFIG_OF) */ +static void __init s3c24xx_gpiolib_add_chips (struct samsung_gpio_chip *chip,int nr_chips,void __iomem *base) {@@ -962,6 +1023,8 @@ static void __init s3c24xx_gpiolib_add_chips(struct samsung_gpio_chip *chip, gc->direction_output = samsung_gpiolib_2bit_output;samsung_gpiolib_add (chip); + + s3c24xx_gpiolib_attach_ofnode(chip, S3C24XX_PA_GPIO, i *
0x10);}Quoted 8 lines
Quoted 4 lines
}
--
1.7.2.3Overall, this is patch looks fine.
Reviewed-by Thomas Abraham <[email protected]>Heiko
PATCH 1/1 gpio: samsung: add devicetree init for s3c24xx arches
In reply to Heiko StübnerQuoted 10 lines · Heiko St?bner
Until now the Exynos-SoC was the only Samsung-SoC supporting the GPIOs via the device tree. This patch implements dt-support for the s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
Signed-off-by Heiko Stuebner <[email protected]>
I cannot figure out if you guys have reached consensus on this patch or not.
I guess this will go through the Samsung tree in any case, I have no objections from a GPIO subsystem point of view.
Yours,
Linus Walleij