gunzip error when uncompress to buf
On host use the flowwing cmd build a gziped file
----------------
$ gzip -c9 zbarebox.bin > xxx
$ ls zbarebox.bin xxx -l -rw-rw-r-- 1 zzs zzs 127605 2012-11-30 17:46 xxx -rwxrwxr-x 1 zzs zzs 136769 2012-11-30 18:44 zbarebox.bin* ----------------
Then on barebox write it to /dev/nor0.kernel
----------------
[barebox@SSR600]:/
# tftp xxx /dev/nor0.kernel ----------------
And add a barebox cmd to uncompress it:
----------------
char ptr[SZ_512K];
static int do_tx(int argc, char *argv[])
{
int ret = 0, size = 0, fd, fd1;
fd = open("/dev/tempmem", O_RDWR);
if(fd < 0)
printf("error open tempmem\n");
fd1 = open("/dev/nor0.kernel", O_RDONLY);
if(fd1 < 0)
printf("error open kernel\n");
ret = uncompress_fd_to_fd (fd1, fd, uncompress_err_stdout);
printf("ret is %d\n", ret);
close(fd1);
fd1 = open("/dev/nor0.kernel", O_RDONLY);
if(fd1 < 0)
printf("error open kernel\n");
ret = uncompress_fd_to_buf(fd1, ptr, uncompress_err_stdout);
printf("ret is %d\n", ret);
return 0;
}BAREBOX_CMD_START(tx)
.cmd = do_tx,
BAREBOX_CMD_END
----------------
Compile barebox, download to board and run this command
----------------
[barebox@SSR600]:/
# tx ret is 0 uncompression error ret is -1 ----------------
The result is:
uncompress_fd_to_fd is OKuncompress_fd_to_buf fail and lib/decompress_inflate.c:gunzip() output a message "uncompression error"
Anybody help me!
Signature · 9 lines
Best Regards, zzs _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 4 lines · 张忠山
On host use the flowwing cmd build a gziped file
----------------
$ gzip -c9 zbarebox.bin > xxx
this is a binary with a decompressor insode you just need to flash it
Best Regards,
J.
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Quoted 7 lines · In message <[email protected]> Jean-Christophe…
Quoted 4 lines · 张忠山
On host use the flowwing cmd build a gziped file
----------------
$ gzip -c9 zbarebox.bin > xxxthis is a binary with a decompressor insode you just need to flash it
I known zbarebox.bin is a compressed image. I just use this file to test uncompress_fd_to_buf.
I will compress my fpga firmware and flash it, So I need to uncompress this image to a buf, then use it to config fpga
But uncompress_fd_to_buf works wrong!
Signature · 9 lines
Best Regards, zzs _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 9 lines · 张忠山
Quoted 7 lines · In message <[email protected]> Jean-Christophe…
Quoted 4 lines · 张忠山
On host use the flowwing cmd build a gziped file
----------------
$ gzip -c9 zbarebox.bin > xxxthis is a binary with a decompressor insode you just need to flash it
Quoted 7 lines
I known zbarebox.bin is a compressed image. I just use this file to test
uncompress_fd_to_buf.I will compress my fpga firmware and flash it, So I need to uncompress this image to a buf, then use it to config fpga
But
uncompress_fd_to_bufworks wrong!
so debug it
Best Regards,
J.
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox