tools: rename kwboot to mvboot
PATCH 1/2 tools: rename kwboot to mvboot
kwboot tool is used to boot Marvell Kirkwood SoCs over the serial link. Before adding support for other Marvell SoCs, such as Dove or Armada, this patch renames the tool so it's name makes more sense in the future.
Signed-off-by Luka Perkov <[email protected]>
CC Prafulla Wadaskar <[email protected]>
CC Sebastian Hesselbarth <[email protected]>
CC Daniel Stodden <[email protected]>
--- doc/kwboot.1 | 84 ------- doc/mvboot.1 | 84 +++++++ tools/.gitignore | 2 +- tools/Makefile | 6 +- tools/kwboot.c | 742 ------------------------------------------------------- tools/mvboot.c | 742 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 6 files changed, 830 insertions(+), 830 deletions(-) delete mode 100644 doc/kwboot.1 create mode 100644 doc/mvboot.1 delete mode 100644 tools/kwboot.c create mode 100644 tools/mvboot.c
doc/kwboot.1 deleted +0 -84
@@ -1,84 +0,0 @@ -.TH KWBOOT 1 "2012-05-19" - -.SH NAME -kwboot \- Boot Marvell Kirkwood SoCs over a serial link. -.SH SYNOPSIS -.B kwboot -.RB [ "-b \fIimage\fP" ] -.RB [ "-p" ] -.RB [ "-t" ] -.RB [ "-B \fIbaudrate\fP" ] -.RB \fITTY\fP -.SH "DESCRIPTION" - -The \fBmkimage\fP program boots boards based on Marvell's Kirkwood -platform over their integrated UART. Boot image files will typically -contain a second stage boot loader, such as U-Boot. The image file -must conform to Marvell's BootROM firmware image format -(\fIkwbimage\fP), created using a tool such as \fBmkimage\fP. - -Following power-up or a system reset, system BootROM code polls the -UART for a brief period of time, sensing a handshake message which -initiates an image upload. This program sends this boot message until -it receives a positive acknowledgement. The image is transfered using -Xmodem. - -Additionally, this program implements a minimal terminal mode, which -can be used either standalone, or entered immediately following boot -image transfer completion. This is often useful to catch early boot -messages, or to manually interrupt a default boot procedure performed -by the second-stage loader. - -.SH "OPTIONS" - -.TP -.BI "\-b \fIimage\fP" -Handshake; then upload file \fIimage\fP over \fITTY\fP. - -Note that for the encapsulated boot code to be executed, \fIimage\fP -must be of type "UART boot" (0x69). Boot images of different types, -such as backup images of vendor firmware downloaded from flash memory -(type 0x8B), will not work (or not as expected). See \fB-p\fP for a -workaround. - -This mode writes handshake status and upload progress indication to -stdout. - -.TP -.BI "\-p" -In combination with \fB-b\fP, patches the header in \fIimage\fP prior -to upload, to "UART boot" type. - -This option attempts on-the-fly conversion of some none-UART image -types, such as images which were originally formatted to be stored in -flash memory. - -Conversion is performed in memory. The contents of \fIimage\fP will -not be altered. - -.TP -.BI "\-t" -Run a terminal program, connecting standard input and output to -.RB \fITTY\fP. - -If used in combination with \fB-b\fP, terminal mode is entered -immediately following a successful image upload. - -If standard I/O streams connect to a console, this mode will terminate -after receiving 'ctrl-\\' followed by 'c' from console input. - -.TP -.BI "\-B \fIbaudrate\fP" -Adjust the baud rate on \fITTY\fP. Default rate is 115200. - -.SH "SEE ALSO" -.PP -\fBmkimage\fP(1) - -.SH "AUTHORS" - -Daniel Stodden <[email protected]> -.br -Luka Perkov <[email protected]> -.br -David Purdy <[email protected]>
doc/mvboot.1 new file +84 -0
84 lines not on this page · raw message
tools/.gitignore +1 -1
@@ -2,10 +2,10 @@ /envcrc /gen_eth_addr /img2srec -/kwboot /mkenvimage /mkimage /mpc86x_clk +/mvboot /mxsboot /ncb /ncp
tools/Makefile +3 -3
@@ -72,7 +72,7 @@ BIN_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl$(SFX) BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX) BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX) BIN_FILES-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1$(SFX) -BIN_FILES-$(CONFIG_KIRKWOOD) += kwboot$(SFX) +BIN_FILES-$(CONFIG_KIRKWOOD) += mvboot$(SFX) # Source files which exist outside the tools directory EXT_OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += common/env_embedded.o
@@ -103,7 +103,7 @@ OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o NOPED_OBJ_FILES-y += os_support.o OBJ_FILES-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1.o NOPED_OBJ_FILES-y += ublimage.o -OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o +OBJ_FILES-$(CONFIG_KIRKWOOD) += mvboot.o # Don't build by default #ifeq ($(ARCH),ppc)
@@ -239,7 +239,7 @@ $(obj)ncb$(SFX): $(obj)ncb.o $(obj)ubsha1$(SFX): $(obj)os_support.o $(obj)sha1.o $(obj)ubsha1.o $(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^ -$(obj)kwboot$(SFX): $(obj)kwboot.o +$(obj)mvboot$(SFX): $(obj)mvboot.o $(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^ $(HOSTSTRIP) $@
tools/kwboot.c deleted +0 -742
742 lines not on this page · raw message
tools/mvboot.c new file +742 -0
742 lines not on this page · raw message
Signature · 1 line
1.8.1.2