DA9058 REGULATOR driver
PATCH v4 7/7 DA9058 REGULATOR driver
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from scripts/checkpatch.pl, but since it seems to be complaining about variable names such as min_uV are in CamelCase, when it is obvious that they are not in CamelCase I have ignored them.
--- drivers/regulator/Kconfig | 11 ++ drivers/regulator/Makefile | 1 + drivers/regulator/da9058-regulator.c | 228 ++++++++++++++++++++++++++++++++++ 3 files changed, 240 insertions(+) create mode 100644 drivers/regulator/da9058-regulator.c
drivers/regulator/Kconfig +11 -0
@@ -64,6 +64,17 @@ config REGULATOR_USERSPACE_CONSUMER If unsure, say no. +config REGULATOR_DA9058 + tristate "Support regulators on Dialog Semiconductor DA9058 PMIC" + depends on MFD_DA9058 + help + Say y here to support the BUCKs and LDOs regulators found on + Dialog Semiconductor DA9058 PMIC. + + This driver can also be built as a module. If so, the module + will be called da9058-regulator. + + config REGULATOR_GPIO tristate "GPIO regulator support" depends on GENERIC_GPIO
drivers/regulator/Makefile +1 -0
@@ -25,6 +25,7 @@ obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o +obj-$(CONFIG_REGULATOR_DA9058) += da9058-regulator.o obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
drivers/regulator/da9058-regulator.c new file +228 -0
228 lines not on this page · raw message
Signature · 1 line
end-of-patch for NEW DRIVER V4
On Fri, Apr 12, 2013 at 02:05:28PM +0100, Anthony Olech wrote:
This looks good, I assume there's some dependencies on the MFD or other earlier patches so I won't apply it, let me know if there aren't any and I will:
Please use subject lines reflecting the subsystem.
Quoted 12 lines
drivers/regulator/da9058-regulator.c new file +12
-0+static int da9058_buck_ramp_voltage (struct regulator_dev *rdev, +unsigned int old_selector, +unsigned int new_selector) +{ +struct da9058_regulator *regulator =rdev_get_drvdata (rdev); +struct da9058 *da9058 = regulator->da9058; +int ret; + +if (regulator->ramp_register ==0 ) +return -EINVAL ; + +if (regulator->ramp_enable_mask ==0 )
drivers/regulator/da9058-regulator.c line 54
Quoted 10 lines
drivers/regulator/da9058-regulator.c new file +10
-0+return -EINVAL ; + + ret =da9058_set_bits (da9058, regulator->ramp_register, + regulator->ramp_enable_mask); + +if (ret) +return ret; + +return 2200 ;/* micro Seconds needed to ramp to new voltage*/ +}
Hrm, this really should be implementable with a generic regmap operation...
drivers/regulator/da9058-regulator.c line 169
Quoted 8 lines
drivers/regulator/da9058-regulator.c new file +8
-0+ rdev =regulator_register (®->desc, &config); + +if (IS_ERR (rdev)) { +dev_err (&pdev->dev,"failed to register %s\n" , + rpdata->regulator_name); + ret =PTR_ERR (rdev); + goto failed_to_register; + }
In general it's a bit better style to print out the return value to help with diagnosis but it's no big deal.
Quoted 10 lines
-----Original Message-----
From: Mark Brown [mailto:[email protected]]
Sent: 12 April 2013 14:27
To: Opensource [Anthony Olech]
Cc: Liam Girdwood; Guenter Roeck; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driver
On Fri, Apr 12, 2013 at 02:05:28PM +0100, Anthony Olech wrote:
This looks good, I assume there's some dependencies on the MFD or other earlier patches so I won't apply it, let me know if there aren't any and I will
I will resubmit later after re-testing, fixing the 3 points you raised in this driver.
Quoted 2 lines
Acked-by Mark Brown <[email protected]>Please use subject lines reflecting the subsystem.
I assume you mean "regulator" for drivers in "drivers/regulator", "misc" for drivers in "drivers/input/misc" etc etc ??
Quoted 15 lines
Quoted 15 lines
drivers/regulator/da9058-regulator.c new file +15
-0+static int da9058_buck_ramp_voltage (struct regulator_dev *rdev, +unsigned int old_selector, +unsigned int new_selector) +{ +struct da9058_regulator *regulator =rdev_get_drvdata (rdev); +struct da9058 *da9058 = regulator->da9058; +int ret; + +if (regulator->ramp_register ==0 ) +return -EINVAL ; + +if (regulator->ramp_enable_mask ==0 ) +return -EINVAL ; + + ret = da9058_set_bits(da9058, regulator->ramp_register,
Quoted 8 lines
drivers/regulator/da9058-regulator.c
Quoted 6 lines
drivers/regulator/da9058-regulator.c new file +6
-0+ regulator->ramp_enable_mask); + +if (ret) +return ret; + +return 2200 ;/* micro Seconds needed to ramp to new voltage*/ }Hrm, this really should be implementable with a generic regmap operation...
Yes, I did not notice that the generic regmap operation "reulator_set_voltage_sel_regmap()" supports a trigger/go. I will change to using it.
Quoted 11 lines
drivers/regulator/da9058-regulator.c line 169
Quoted 8 lines
drivers/regulator/da9058-regulator.c new file +8
-0+ rdev =regulator_register (®->desc, &config); + +if (IS_ERR (rdev)) { +dev_err (&pdev->dev,"failed to register %s\n" , + rpdata->regulator_name); + ret =PTR_ERR (rdev); + goto failed_to_register; + }In general it's a bit better style to print out the return value to help with diagnosis but it's no big deal.
Yes, I will include the value of "ret" in the dev_err message
Tony Olech
Quoted 8 lines · Anthony Olech
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I have ignored them.
??? min_uV _is_ CamelCase ???
Ok, maybe it is camelcasE, but you are splitting hairs here.
Guenter
Quoted 281 lines
Signed-off-by Anthony Olech <[email protected]>Signed-off-by David Dajun Chen <[email protected]>--- drivers/regulator/Kconfig | 11 ++ drivers/regulator/Makefile | 1 + drivers/regulator/da9058-regulator.c | 228 ++++++++++++++++++++++++++++++++++ 3 files changed, 240 insertions(+) create mode 100644 drivers/regulator/da9058-regulator.cdrivers/regulator/Kconfig +11
-0@@ -64,6 +64,17 @@ config REGULATOR_USERSPACE_CONSUMER If unsure, say no. +config REGULATOR_DA9058 + tristate "Support regulators on Dialog Semiconductor DA9058 PMIC" + depends on MFD_DA9058 + help + Say y here to support the BUCKs and LDOs regulators found on + Dialog Semiconductor DA9058 PMIC. + + This driver can also be built as a module. If so, the module + will be called da9058-regulator. + + config REGULATOR_GPIO tristate "GPIO regulator support" depends on GENERIC_GPIOdrivers/regulator/Makefile +1
-0@@ -25,6 +25,7 @@ obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o +obj-$(CONFIG_REGULATOR_DA9058) += da9058-regulator.o obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o obj-$(CONFIG_REGULATOR_LP872X) += lp872x.odrivers/regulator/da9058-regulator.c new file +228
-0@@ -0,0 +1,228 @@ +/* +* Copyright (C) 2012 Dialog Semiconductor Ltd. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +*/ + +#include <linux/module.h> +#include <linux/err.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/driver.h> +#include <linux/regmap.h> +#include <linux/mfd/core.h> + +#include <linux/mfd/da9058/version.h> +#include <linux/mfd/da9058/registers.h> +#include <linux/mfd/da9058/core.h> +#include <linux/mfd/da9058/regulator.h> + +struct da9058_regulator { +struct da9058 *da9058; +int ramp_register; +int ramp_enable_mask; +struct platform_device *pdev; +struct regulator_dev *reg_dev; +struct regulator_desc desc; +struct regulator_init_data init; +}; + +static int da9058_buck_ramp_voltage (struct regulator_dev *rdev, +unsigned int old_selector, +unsigned int new_selector) +{ +struct da9058_regulator *regulator =rdev_get_drvdata (rdev); +struct da9058 *da9058 = regulator->da9058; +int ret; + +if (regulator->ramp_register ==0 ) +return -EINVAL ; + +if (regulator->ramp_enable_mask ==0 ) +return -EINVAL ; + + ret =da9058_set_bits (da9058, regulator->ramp_register, + regulator->ramp_enable_mask); + +if (ret) +return ret; + +return 2200 ;/* micro Seconds needed to ramp to new voltage*/ +} + +static struct regulator_ops da9058_buck_regulator_ops = { + .map_voltage = regulator_map_voltage_linear, + .list_voltage = regulator_list_voltage_linear, + .set_voltage_time_sel = da9058_buck_ramp_voltage, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static struct regulator_ops da9058_ldo_regulator_ops = { + .map_voltage = regulator_map_voltage_linear, + .list_voltage = regulator_list_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + +static int da9058_regulator_probe (struct platform_device *pdev) +{ +struct da9058 *da9058 =dev_get_drvdata (pdev->dev.parent); +const struct mfd_cell *cell =mfd_get_cell (pdev); +struct da9058_regulator_pdata *rpdata; +struct da9058_regulator *reg; +struct regulator_dev *rdev; +struct regulator_config config = { }; +int ret; +unsigned int val; + +if (cell ==NULL ) { + ret = -ENODEV ; + goto exit; + } + + rpdata = cell->platform_data; + +if (rpdata ==NULL ) { + ret = -EINVAL ; + goto exit; + } + +if (rpdata->control_register ==0 ) { + ret = -EINVAL ; + goto exit; + } + +if (rpdata->control_enable_mask ==0 ) { + ret = -EINVAL ; + goto exit; + } + + reg =devm_kzalloc (&pdev->dev,sizeof (struct da9058_regulator ), +GFP_KERNEL ); +if (!reg) { + ret = -ENOMEM ; + goto exit; + } + +platform_set_drvdata (pdev, reg); + + reg->da9058 = da9058; + reg->pdev = pdev; + reg->ramp_register = rpdata->ramp_register; + reg->ramp_enable_mask = rpdata->ramp_enable_mask; + + reg->desc.name = rpdata->regulator_name; + reg->desc.id = rpdata->regulator_id; + reg->desc.type =REGULATOR_VOLTAGE ; + reg->desc.n_voltages =1 ; + +if (rpdata->control_voltage_step >0 ) + reg->desc.n_voltages += (rpdata->max_uV - rpdata->min_uV) / + rpdata->control_voltage_step; + + reg->desc.owner =THIS_MODULE ; + reg->desc.enable_reg = rpdata->control_register; + reg->desc.enable_mask = rpdata->control_enable_mask; + + reg->desc.vsel_reg = rpdata->control_register; + reg->desc.vsel_mask = rpdata->control_step_mask; + reg->desc.min_uV = rpdata->min_uV; + reg->desc.uV_step = rpdata->control_voltage_step; + +if (reg->ramp_register) + reg->desc.ops = &da9058_buck_regulator_ops; +else + reg->desc.ops = &da9058_ldo_regulator_ops; + + reg->init.constraints.name = rpdata->regulator_name; + reg->init.constraints.min_uV = rpdata->min_uV; + reg->init.constraints.max_uV = rpdata->max_uV; + reg->init.constraints.valid_ops_mask = rpdata->valid_ops_mask; + reg->init.constraints.valid_modes_mask = rpdata->valid_modes_mask; + reg->init.constraints.boot_on = rpdata->boot_on; + reg->init.constraints.always_on = rpdata->always_on; + reg->init.num_consumer_supplies = rpdata->num_consumer_supplies; + reg->init.consumer_supplies = rpdata->consumer_supplies; + + config.dev = pdev->dev.parent; + config.init_data = ®->init; + config.driver_data = reg; + config.regmap = da9058->regmap; + + rdev =regulator_register (®->desc, &config); + +if (IS_ERR (rdev)) { +dev_err (&pdev->dev,"failed to register %s\n" , + rpdata->regulator_name); + ret =PTR_ERR (rdev); + goto failed_to_register; + } + reg->reg_dev = rdev; + +/* before we do anything check the lock bit */ + ret =da9058_reg_read (da9058,DA9058_SUPPLY_REG , &val); +if (ret) + goto unlock_failed; + +if (val &DA9058_SUPPLY_VLOCK ) + ret =da9058_clear_bits (da9058,DA9058_SUPPLY_REG , +DA9058_SUPPLY_VLOCK ); +if (ret) + goto unlock_failed; + + goto exit; + +unlock_failed: +regulator_unregister (rdev); +failed_to_register: +platform_set_drvdata (pdev,NULL ); +exit: +return ret; +} + +static int da9058_regulator_remove (struct platform_device *pdev) +{ +struct regulator_dev *rdev =platform_get_drvdata (pdev); + +regulator_unregister (rdev); + +return 0 ; +} + +static struct platform_driver da9058_regulator_driver = { + .probe = da9058_regulator_probe, + .remove = da9058_regulator_remove, + .driver = { + .name ="da9058-regulator" , + .owner =THIS_MODULE , + }, +}; + +static int __init da9058_regulator_init (void ) +{ +return platform_driver_register (&da9058_regulator_driver); +} + +subsys_initcall (da9058_regulator_init); + +static void __exit da9058_regulator_exit(void) +{ +platform_driver_unregister (&da9058_regulator_driver); +} + +module_exit (da9058_regulator_exit); + +MODULE_DESCRIPTION ("Dialog DA9058 PMIC voltage and current regulator" ); +MODULE_AUTHOR ("Anthony Olech <[email protected]>" ); +MODULE_LICENSE ("GPL v2" ); +MODULE_ALIAS ("platform:da9058-regulator" );Signature · 1 line
end-of-patch for NEW DRIVER V4
Quoted 15 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 4 lines · Anthony Olech
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
Quoted 7 lines
Quoted 4 lines
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I have ignored them.???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is scripts/checkpatch.pl
Tony Olech
Quoted 19 lines · Opensource [Anthony Olech]
Quoted 19 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 8 lines · Anthony Olech
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I have ignored them.
Quoted 6 lines
Quoted 3 lines
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.pl
Maybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCase
By abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Guenter
Quoted 41 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 17:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 10 lines · Opensource [Anthony Olech]
Quoted 10 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 8 lines
Quoted 8 lines · Anthony Olech
Quoted 7 lines
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I haveignored them.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.plMaybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCase
Quoted 7 lines
By abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Guenter
I always thought that camel case meant "changing from lower case to upper case the first letter of each word and then joining the capitalized words together", so by that definition uV or mW are not camel case because "v" and "w" are not words!
Either way it seems that the algorithm in scripts/checkpatch.pl is wrong! and that was my point.
Tony Olech
Quoted 47 lines · Opensource [Anthony Olech]
Quoted 47 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 17:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 10 lines · Opensource [Anthony Olech]
Quoted 10 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 8 lines
Quoted 8 lines · Anthony Olech
Quoted 7 lines
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I haveignored them.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.plMaybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCaseBy abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Quoted 8 lines
Quoted 1 line
Guenter
I always thought that camel case meant "changing from lower case to upper case the first letter of each word and then joining the capitalized words together", so by that definition uV or mW are not camel case because "v" and "w" are not words!
Either way it seems that the algorithm in
scripts/checkpatch.plis wrong! and that was my point.
Guess we'll have to agree to disagree here, as I happen to think that checkpatch is perfectly right.
Guenter
Quoted 57 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 18:46
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 48 lines · Opensource [Anthony Olech]
Quoted 48 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 17:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 11 lines · Opensource [Anthony Olech]
Quoted 11 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverOn Fri, Apr 12, 2013 at 02:05:28PM +0100, Anthony Olech wrote:
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I haveignored them.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.plMaybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCaseBy abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Quoted 6 lines
Quoted 5 lines
Quoted 1 line
Guenter
I always thought that camel case meant "changing from lower case to upper case the first letter of each word and then joining the capitalized words together", so by that definition uV or mW are not camel
case because "v" and "w" are not words!
The definition of CamelCase From Wikipedia, the free encyclopedia is:
"CamelCase (camel case) is a term which refers to the practice of writing compound words where the first letter of an identifier is lowercase and the first letter of each subsequent concatenated word is capitalized."
Quoted 6 lines
Quoted 1 line
Either way it seems that the algorithm in
scripts/checkpatch.plis wrong! andthat was my point.
Guess we'll have to agree to disagree here, as I happen to think that checkpatch is perfectly right.
Guenter
Hi Guenter,
I am quite happy to accept the algorithm in scripts/checkpatch.pl as the arbiter for correctly formed linux kernel variable names.
On that basis "old_mV", "new_uA" etc are incorrectly formed variable names. Could you possibly suggest legal alternatives to "mA", "uV", "kW" ??
Tony Olech
Quoted 62 lines · Opensource [Anthony Olech]
Quoted 62 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 18:46
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 53 lines · Opensource [Anthony Olech]
Quoted 42 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 17:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 11 lines · Opensource [Anthony Olech]
Quoted 11 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverOn Fri, Apr 12, 2013 at 02:05:28PM +0100, Anthony Olech wrote:
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
This is the REGULATOR component driver of the Dialog DA9058 PMIC. This driver is just one component of the whole DA9058 PMIC driver. It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I haveignored them.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.plMaybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCaseQuoted 7 lines
By abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Guenter
I always thought that camel case meant "changing from lower case to upper case the first letter of each word and then joining the capitalized words together", so by that definition uV or mW are not camel
Quoted 8 lines
Quoted 1 line
case because "v" and "w" are not words!
The definition of CamelCase From Wikipedia, the free encyclopedia is:
"CamelCase (camel case) is a term which refers to the practice of writing compound words where the first letter of an identifier is lowercase and the first letter of each subsequent concatenated word is capitalized."
Maybe the rule should read "don't mix lowercase and uppercase letters in variable names and defines" to prevent variable names such as cAmelcAse or cameLcasE, which would be permitted with your logic :).
Quoted 7 lines
Quoted 6 lines
Quoted 1 line
Either way it seems that the algorithm in
scripts/checkpatch.plis wrong! andthat was my point.
Guess we'll have to agree to disagree here, as I happen to think that checkpatch is perfectly right.
Guenter
Quoted 8 lines
Hi Guenter,
I am quite happy to accept the algorithm in
scripts/checkpatch.plas the arbiter for correctly formed linux kernel variable names.On that basis "
old_mV", "new_uA" etc are incorrectly formed variable names. Could you possibly suggest legal alternatives to "mA", "uV", "kW" ??
I just changed it to lowercase in the ntc_thermistor driver. What you use is really your call as long as it does not mix uppercase and lowercase letters.
Guenter
Quoted 79 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 16 April 2013 14:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 29 lines · Opensource [Anthony Olech]
Quoted 29 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 18:46
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 20 lines · Opensource [Anthony Olech]
Quoted 20 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 15 April 2013 17:36
To: Opensource [Anthony Olech]
Cc: LKML
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 10 lines · Opensource [Anthony Olech]
Quoted 10 lines
-----Original Message-----
From: Guenter Roeck [mailto:[email protected]]
Sent: 12 April 2013 14:32
To: Opensource [Anthony Olech]
Cc: Mark Brown; Liam Girdwood; Jean Delvare; Randy Dunlap; LKML; David Dajun Chen
Subject: Re: [NEW DRIVER V4 7/7] DA9058 REGULATOR driverQuoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines · Anthony Olech
Quoted 1 line
This is the REGULATOR component driver of the Dialog DA9058
PMIC.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
This driver is just one component of the whole DA9058 PMIC
driver.
Quoted 36 lines
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
It depends on the CORE component driver of the DA9058 MFD.
There are 6 warnings from
scripts/checkpatch.pl, but since it seems to be complaining about variable names such asmin_uVare in CamelCase, when it is obvious that they are not in CamelCase I haveignored them.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
???
min_uV_is_ CamelCase ???Ok, maybe it is camelcasE, but you are splitting hairs here.
it is not me splitting hairs, it is
scripts/checkpatch.plMaybe you did not understand what I meant. Per your logic,
MicroVolt is CamelCase
uVolt is ???
uV is not CamelCaseBy abbreviating CamelCase to camelCase to cC you make it, in your opinion, acceptable.
If you want to declare CamelCase variables, just do it, but don't claim that they are not really CamelCase.
Quoted 7 lines
Quoted 6 lines
Quoted 1 line
Guenter
I always thought that camel case meant "changing from lower case to upper case the first letter of each word and then joining the capitalized words together", so by that definition uV or mW are not camel
case because "v" and "w" are not words!
The definition of CamelCase From Wikipedia, the free encyclopedia is:
Quoted 8 lines
Quoted 3 lines
"CamelCase (camel case) is a term which refers to the practice of writing compound words where the first letter of an identifier is lowercase and the first letter of each subsequent concatenated word is
capitalized."
Quoted 1 line
Maybe the rule should read "don't mix lowercase and uppercase letters in variable names and defines" to prevent variable names such as cAmelcAse or cameLcasE, which would be permitted with your logic :).
It is really good to have a definition that anyone can work with!
Quoted 13 lines
Quoted 13 lines
Quoted 7 lines
Quoted 2 lines
Either way it seems that the algorithm in
scripts/checkpatch.plis wrong! andthat was my point.
Guess we'll have to agree to disagree here, as I happen to think that checkpatch is perfectly right.
GuenterHi Guenter,
I am quite happy to accept the algorithm in
scripts/checkpatch.plas the arbiter for correctly formed linux kernel variable names.
Quoted 7 lines
Quoted 3 lines
On that basis "
old_mV", "new_uA" etc are incorrectly formed variable names. Could you possibly suggest legal alternatives to "mA", "uV", "kW" ??I just changed it to lowercase in the
ntc_thermistordriver. What you use is really your call as long as it does not mix uppercase and lowercase letters.Guenter
many thanks, I will do the same.
Tony Olech