still in 3.9-rc6 - fan speed at 100% after suspend/resume regression
[ not sure why, but the lkml address got munged in Rui's reply ... fixed now -- sorry for the dupe ]
Quoted 8 lines · On Sun, 14 Apr 2013 02:20:15 +0800 Zhang Rui wrote:
Quoted 5 lines
A brief recap: after resuming, the fan on the laptop spins up to full speed and stays there. "temp6" in "acpitz-virtual-0" (as shown by "sensors") is 100°C and stays there, which is presumably what is making the fan stay on.
first, this seems like the same problem reported at
https://bugzilla.kernel.org/show_bug.cgi?id=50041
please refer to comment #17 and #27.
Yes, it does seem like the same bug that Matthias is talking about in those comments ...
Quoted 3 lines
Quoted 2 lines
Is more information needed?
please attach the acpidump output of your laptop.
I have the dump, do you want it on the old closed bug or shall I wait until Matthias opens a new one?
Quoted 2 lines
can you please test thermal -thermal branch at
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux.git
I just tried it, no difference in behavior (fan on full, temp6 == 100°C) ...
I took all the defaults when I did a 'make oldconfig', some of which looked thermal-related ... was I supposed to set them differently?
thanks,
jake
Signature · 1 line
Jake Edge - LWN - [email protected] - http://lwn.net
Quoted 9 lines · Jake Edge
Hi Zhang Rui,
The problem reported in https://lkml.org/lkml/2012/12/4/428 (and incorrectly attributed to a suspend patch by me here:
https://lkml.org/lkml/2013/4/12/314) still exists in 3.9-rc6, at least for my HP/Compaq 2510p laptop. It appeared that some folks were seeing some improvement with earlier 3.9-rcs (?) but I just tested rc6 and saw substantially the same behavior. This all works fine in <= 3.6.11.
Quoted 4 lines
A brief recap: after resuming, the fan on the laptop spins up to full speed and stays there. "temp6" in "acpitz-virtual-0" (as shown by "sensors") is 100°C and stays there, which is presumably what is making the fan stay on.
My HP Compaq NC6000 exhibits slightly different behaviour. For me the reported temp is always accurate but the trip points get out of sync with the actual temperature.
With 3.7 I saw two different kinds of problems coming out of resume. In one case the fan stays on until the temp rises high enough to get the trip points back into sync. In the other case the fan goes off, and stays off even when the temperature rises above the highest active trip point, but it does appear to get back into sync when the temp starts to come back down. I think the difference might stem from resuming when the laptop has cooled down fully vs. when it's still warm.
I also just tried 3.9-rc6, and that one appears to behave differently to 3.7, but still wrong. There the fan goes off after resume, and comes back on as the temperature rises, but it never slows back down after that.
I'll try to collect some more detailed dumps of all three cases.
Signature · 3 lines
Ville Syrjälä [email protected] http://www.sci.fi/~syrjala/
Quoted 27 lines · Ville Syrjälä
Quoted 9 lines · Jake Edge
Hi Zhang Rui,
The problem reported in https://lkml.org/lkml/2012/12/4/428 (and incorrectly attributed to a suspend patch by me here:
https://lkml.org/lkml/2013/4/12/314) still exists in 3.9-rc6, at least for my HP/Compaq 2510p laptop. It appeared that some folks were seeing some improvement with earlier 3.9-rcs (?) but I just tested rc6 and saw substantially the same behavior. This all works fine in <= 3.6.11.Quoted 4 lines
A brief recap: after resuming, the fan on the laptop spins up to full speed and stays there. "temp6" in "acpitz-virtual-0" (as shown by "sensors") is 100°C and stays there, which is presumably what is making the fan stay on.
My HP Compaq NC6000 exhibits slightly different behaviour. For me the reported temp is always accurate but the trip points get out of sync with the actual temperature.
With 3.7 I saw two different kinds of problems coming out of resume. In one case the fan stays on until the temp rises high enough to get the trip points back into sync. In the other case the fan goes off, and stays off even when the temperature rises above the highest active trip point, but it does appear to get back into sync when the temp starts to come back down. I think the difference might stem from resuming when the laptop has cooled down fully vs. when it's still warm.
Quoted 6 lines
I also just tried 3.9-rc6, and that one appears to behave differently to 3.7, but still wrong. There the fan goes off after resume, and comes back on as the temperature rises, but it never slows back down after that.
I'll try to collect some more detailed dumps of all three cases.
I filed a new bug and attached all my logs:
https://bugzilla.kernel.org/show_bug.cgi?id=56591
Signature · 3 lines
Ville Syrjälä [email protected] http://www.sci.fi/~syrjala/
Quoted 33 lines · Ville Syrjälä
Quoted 32 lines · Ville Syrjälä
Quoted 9 lines · Jake Edge
Hi Zhang Rui,
The problem reported in https://lkml.org/lkml/2012/12/4/428 (and incorrectly attributed to a suspend patch by me here:
https://lkml.org/lkml/2013/4/12/314) still exists in 3.9-rc6, at least for my HP/Compaq 2510p laptop. It appeared that some folks were seeing some improvement with earlier 3.9-rcs (?) but I just tested rc6 and saw substantially the same behavior. This all works fine in <= 3.6.11.Quoted 4 lines
A brief recap: after resuming, the fan on the laptop spins up to full speed and stays there. "temp6" in "acpitz-virtual-0" (as shown by "sensors") is 100°C and stays there, which is presumably what is making the fan stay on.
My HP Compaq NC6000 exhibits slightly different behaviour. For me the reported temp is always accurate but the trip points get out of sync with the actual temperature.
With 3.7 I saw two different kinds of problems coming out of resume. In one case the fan stays on until the temp rises high enough to get the trip points back into sync. In the other case the fan goes off, and stays off even when the temperature rises above the highest active trip point, but it does appear to get back into sync when the temp starts to come back down. I think the difference might stem from resuming when the laptop has cooled down fully vs. when it's still warm.
I also just tried 3.9-rc6, and that one appears to behave differently to 3.7, but still wrong. There the fan goes off after resume, and comes back on as the temperature rises, but it never slows back down after that.
Quoted 5 lines
Quoted 1 line
I'll try to collect some more detailed dumps of all three cases.
I filed a new bug and attached all my logs:
https://bugzilla.kernel.org/show_bug.cgi?id=56591
Rui, does this one gets fixed with your series to make the parts of thermal framework to be glued together in a single module? Or does this one is a new bug?
Quoted 36 lines · Eduardo Valentin
Quoted 35 lines · Ville Syrjälä
Quoted 33 lines · Ville Syrjälä
Quoted 9 lines · Jake Edge
Hi Zhang Rui,
The problem reported in https://lkml.org/lkml/2012/12/4/428 (and incorrectly attributed to a suspend patch by me here:
https://lkml.org/lkml/2013/4/12/314) still exists in 3.9-rc6, at least for my HP/Compaq 2510p laptop. It appeared that some folks were seeing some improvement with earlier 3.9-rcs (?) but I just tested rc6 and saw substantially the same behavior. This all works fine in <= 3.6.11.Quoted 4 lines
A brief recap: after resuming, the fan on the laptop spins up to full speed and stays there. "temp6" in "acpitz-virtual-0" (as shown by "sensors") is 100°C and stays there, which is presumably what is making the fan stay on.
My HP Compaq NC6000 exhibits slightly different behaviour. For me the reported temp is always accurate but the trip points get out of sync with the actual temperature.
With 3.7 I saw two different kinds of problems coming out of resume. In one case the fan stays on until the temp rises high enough to get the trip points back into sync. In the other case the fan goes off, and stays off even when the temperature rises above the highest active trip point, but it does appear to get back into sync when the temp starts to come back down. I think the difference might stem from resuming when the laptop has cooled down fully vs. when it's still warm.
I also just tried 3.9-rc6, and that one appears to behave differently to 3.7, but still wrong. There the fan goes off after resume, and comes back on as the temperature rises, but it never slows back down after that.
I'll try to collect some more detailed dumps of all three cases.
Quoted 7 lines
Quoted 3 lines
I filed a new bug and attached all my logs:
https://bugzilla.kernel.org/show_bug.cgi?id=56591Rui, does this one gets fixed with your series to make the parts of thermal framework to be glued together in a single module?
No.
Quoted 3 lines
Or does this
one is a new bug?
right, it is a new bug.
thanks,
rui