Skip to contentSkip to conversation

pull request: wireless 2013-06-03

PATCH John W. Linville 2 participants 3 messages Jun 3, 2013 – Jun 4, 2013

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

Dave,

Still another batch of fixes intended for the 3.10 stream... This includes a big batch of fixes for brcmfmac, along with a Bluetooth pull and a couple of other fixes.

Regarding the brcmfmac batch, Arend makes the following plea:

"This is a somewhat large series and reading the message of the announcement of v3.10-rc3 I think it is good to give our story up front. Firmware-signalling is a new feature merged in for 3.10, which was a major overhaul of the transmit path in brcmfmac. During and after the merge window we still have some blanks in our test coverage and further testing revealed issues with P2P, TDLS, and power-saving clients in AP mode. These issues have been fixed in this series."

As for the Bluetooth bits, Gustavo says:

"The following patches are important bug fixes for 3.10, plus the support for a new device. We do have three fixes from Johan. The first one is a fix to avoid LE-only devices to rely on the (inexistent) extended features data. The second patch fixes length checks on incoming L2CAP signalling PDUs so we can discard PDU whose size doesn't match the one reported in the header. The last one fixes the handling of power on failures, we now report proper errors to mgmt when hci_dev_open()."

Along with that...

Arend also reverts an earlier brcmsmac patch that causes a regression in 3.10-rc1.

Larry Finger corrects an rtlwifi problem that caused some devices to refuse to connect to non-WPA2 networks if the device had previously assocated with a WPA2 network.

Mark A. Greer fixes an out of bounds array access in mwifiex.

Please let me know if there are problems!

John

---

The following changes since commit 01cb71d2d47b78354358e4bb938bb06323e17498:

net_sched: restore "overhead xxx" handling (2013-06-02 22:22:35 -0700)

are available in the git repository at:

git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless.git for-davem

for you to fetch changes up to 6eba8cf4d7b3d9fce0575927777407743bd070bb:

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem (2013-06-03 14:18:13 -0400)

----------------------------------------------------------------

Arend van Spriel (7):
brcmfmac: allow firmware-signal tlv to be longer than specified
brcmfmac: remove fifo bitfield from brcmf_skbuff_cb::if_flags
brcmfmac: rework credit pickup to assure consistent handling
brcmfmac: explicitly indicate sk_buff is sent upon request credit
brcmfmac: reducing debug logging in firmware-signalling code
brcmfmac: Sent TIM information in case of data available.
brcmsmac: fix regression observed in 3.10-rc1

Bing Zhao (1):
Bluetooth: btmrvl: support Marvell Bluetooth device SD8897

Hante Meuleman (10):
brcmfmac: Take bus flowcontrol at credit mgmt into account.
brcmfmac: On bus flow control use fw signalling or netif.
brcmfmac: For FW signalling it is necessary to track gen bit.
brcmfmac: Correct creditmap when credit borrowing is active.
brcmfmac: Find correct MAC descriptor in case of TDLS.
brcmfmac: fix invalid ifp lookup in firmware-signalling
brcmfmac: Accept only first creditmap event.
brcmfmac: Signalling header push and pull on logic places.
brcmfmac: Fix endless loop when brcmf_fws_commit_skb fails.
brcmfmac: Simplify counting transit count.

Johan Hedberg (3):
Bluetooth: Fix checks for LE support on LE-only controllers
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
Bluetooth: Fix mgmt handling of power on failures

John W. Linville (1):
Merge branch 'master' of git://git.kernel.org/.../linville/wireless into for-davem

Larry Finger (1):
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks

Mark A. Greer (1):
mwifiex: debugfs: Fix out of bounds array access

 drivers/bluetooth/Kconfig                          |   4 +-
 drivers/bluetooth/btmrvl_sdio.c                    |  28 +
 drivers/net/wireless/brcm80211/brcmfmac/dhd.h      |   2 +
 .../net/wireless/brcm80211/brcmfmac/dhd_linux.c    |  21 +-
 drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c |   2 +-
 drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c | 638 ++++++++++-----------
 drivers/net/wireless/brcm80211/brcmfmac/fwsignal.h |   1 +
 drivers/net/wireless/brcm80211/brcmfmac/usb.c      |   8 +
 drivers/net/wireless/brcm80211/brcmsmac/main.c     |  17 +-
 drivers/net/wireless/mwifiex/debugfs.c             |  22 +-
 drivers/net/wireless/rtlwifi/rtl8192cu/hw.c        | 134 +++--
 drivers/net/wireless/rtlwifi/rtl8192cu/hw.h        |   4 -
 drivers/net/wireless/rtlwifi/rtl8192cu/mac.c       |  18 +-
 drivers/net/wireless/rtlwifi/rtl8192cu/sw.c        |   4 +-
 drivers/net/wireless/rtlwifi/rtl8192cu/sw.h        |   3 +
 drivers/net/wireless/rtlwifi/usb.c                 |  13 +
 drivers/net/wireless/rtlwifi/wifi.h                |   4 +
 include/net/bluetooth/hci_core.h                   |   1 +
 include/net/bluetooth/mgmt.h                       |   1 +
 net/bluetooth/hci_core.c                           |   6 +-
 net/bluetooth/l2cap_core.c                         |  70 ++-
 net/bluetooth/mgmt.c                               |  23 +-
 net/bluetooth/smp.c                                |   4 +-
 23 files changed, 610 insertions(+), 418 deletions(-)
drivers/bluetooth/Kconfig +2 -2
index fdfd61a..11a6104 100644
@@ -201,7 +201,7 @@ config BT_MRVL
 	  The core driver to support Marvell Bluetooth devices.
 
 	  This driver is required if you want to support
-	  Marvell Bluetooth devices, such as 8688/8787/8797.
+	  Marvell Bluetooth devices, such as 8688/8787/8797/8897.
 
 	  Say Y here to compile Marvell Bluetooth driver
 	  into the kernel or say M to compile it as module.
@@ -214,7 +214,7 @@ config BT_MRVL_SDIO
 	  The driver for Marvell Bluetooth chipsets with SDIO interface.
 
 	  This driver is required if you want to use Marvell Bluetooth
-	  devices with SDIO interface. Currently SD8688/SD8787/SD8797
+	  devices with SDIO interface. Currently SD8688/SD8787/SD8797/SD8897
 	  chipsets are supported.
 
 	  Say Y here to compile support for Marvell BT-over-SDIO driver
drivers/bluetooth/btmrvl_sdio.c +28 -0
index c63488c..13693b7 100644
@@ -82,6 +82,23 @@ static const struct btmrvl_sdio_card_reg btmrvl_reg_87xx = {
 	.io_port_2 = 0x7a,
 };
 
+static const struct btmrvl_sdio_card_reg btmrvl_reg_88xx = {
+	.cfg = 0x00,
+	.host_int_mask = 0x02,
+	.host_intstatus = 0x03,
+	.card_status = 0x50,
+	.sq_read_base_addr_a0 = 0x60,
+	.sq_read_base_addr_a1 = 0x61,
+	.card_revision = 0xbc,
+	.card_fw_status0 = 0xc0,
+	.card_fw_status1 = 0xc1,
+	.card_rx_len = 0xc2,
+	.card_rx_unit = 0xc3,
+	.io_port_0 = 0xd8,
+	.io_port_1 = 0xd9,
+	.io_port_2 = 0xda,
+};
+
 static const struct btmrvl_sdio_device btmrvl_sdio_sd8688 = {
 	.helper		= "mrvl/sd8688_helper.bin",
 	.firmware	= "mrvl/sd8688.bin",
@@ -103,6 +120,13 @@ static const struct btmrvl_sdio_device btmrvl_sdio_sd8797 = {
 	.sd_blksz_fw_dl	= 256,
 };
 
+static const struct btmrvl_sdio_device btmrvl_sdio_sd8897 = {
+	.helper		= NULL,
+	.firmware	= "mrvl/sd8897_uapsta.bin",
+	.reg		= &btmrvl_reg_88xx,
+	.sd_blksz_fw_dl	= 256,
+};
+
 static const struct sdio_device_id btmrvl_sdio_ids[] = {
 	/* Marvell SD8688 Bluetooth device */
 	{ SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, 0x9105),
@@ -116,6 +140,9 @@ static const struct sdio_device_id btmrvl_sdio_ids[] = {
 	/* Marvell SD8797 Bluetooth device */
 	{ SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, 0x912A),
 			.driver_data = (unsigned long) &btmrvl_sdio_sd8797 },
+	/* Marvell SD8897 Bluetooth device */
+	{ SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, 0x912E),
+			.driver_data = (unsigned long) &btmrvl_sdio_sd8897 },
 
 	{ }	/* Terminating entry */
 };
@@ -1194,3 +1221,4 @@ MODULE_FIRMWARE("mrvl/sd8688_helper.bin");
 MODULE_FIRMWARE("mrvl/sd8688.bin");
 MODULE_FIRMWARE("mrvl/sd8787_uapsta.bin");
 MODULE_FIRMWARE("mrvl/sd8797_uapsta.bin");
+MODULE_FIRMWARE("mrvl/sd8897_uapsta.bin");
drivers/net/wireless/brcm80211/brcmfmac/dhd.h +2 -0
index 28db9cf..86cbfe2 100644
@@ -583,6 +583,7 @@ enum brcmf_netif_stop_reason {
  * @bssidx: index of bss associated with this interface.
  * @mac_addr: assigned mac address.
  * @netif_stop: bitmap indicates reason why netif queues are stopped.
+ * @netif_stop_lock: spinlock for update netif_stop from multiple sources.
  * @pend_8021x_cnt: tracks outstanding number of 802.1x frames.
  * @pend_8021x_wait: used for signalling change in count.
  */
@@ -598,6 +599,7 @@ struct brcmf_if {
 	s32 bssidx;
 	u8 mac_addr[ETH_ALEN];
 	u8 netif_stop;
+	spinlock_t netif_stop_lock;
 	atomic_t pend_8021x_cnt;
 	wait_queue_head_t pend_8021x_wait;
 };
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +16 -5
index b98f223..63cadf6 100644
@@ -179,7 +179,7 @@ static netdev_tx_t brcmf_netdev_start_xmit(struct sk_buff *skb,
 	struct brcmf_pub *drvr = ifp->drvr;
 	struct ethhdr *eh;
 
-	brcmf_dbg(TRACE, "Enter, idx=%d\n", ifp->bssidx);
+	brcmf_dbg(DATA, "Enter, idx=%d\n", ifp->bssidx);
 
 	/* Can the device send data? */
 	if (drvr->bus_if->state != BRCMF_BUS_DATA) {
@@ -240,11 +240,15 @@ done:
 void brcmf_txflowblock_if(struct brcmf_if *ifp,
 			  enum brcmf_netif_stop_reason reason, bool state)
 {
+	unsigned long flags;
+
 	if (!ifp)
 		return;
 
 	brcmf_dbg(TRACE, "enter: idx=%d stop=0x%X reason=%d state=%d\n",
 		  ifp->bssidx, ifp->netif_stop, reason, state);
+
+	spin_lock_irqsave(&ifp->netif_stop_lock, flags);
 	if (state) {
 		if (!ifp->netif_stop)
 			netif_stop_queue(ifp->ndev);
@@ -254,6 +258,7 @@ void brcmf_txflowblock_if(struct brcmf_if *ifp,
 		if (!ifp->netif_stop)
 			netif_wake_queue(ifp->ndev);
 	}
+	spin_unlock_irqrestore(&ifp->netif_stop_lock, flags);
 }
 
 void brcmf_txflowblock(struct device *dev, bool state)
@@ -264,9 +269,14 @@ void brcmf_txflowblock(struct device *dev, bool state)
 
 	brcmf_dbg(TRACE, "Enter\n");
 
-	for (i = 0; i < BRCMF_MAX_IFS; i++)
-		brcmf_txflowblock_if(drvr->iflist[i],
-				     BRCMF_NETIF_STOP_REASON_BLOCK_BUS, state);
+	if (brcmf_fws_fc_active(drvr->fws)) {
+		brcmf_fws_bus_blocked(drvr, state);
+	} else {
+		for (i = 0; i < BRCMF_MAX_IFS; i++)
+			brcmf_txflowblock_if(drvr->iflist[i],
+					     BRCMF_NETIF_STOP_REASON_BLOCK_BUS,
+					     state);
+	}
 }
 
 void brcmf_rx_frames(struct device *dev, struct sk_buff_head *skb_list)
@@ -280,7 +290,7 @@ void brcmf_rx_frames(struct device *dev, struct sk_buff_head *skb_list)
 	u8 ifidx;
 	int ret;
 
-	brcmf_dbg(TRACE, "Enter\n");
+	brcmf_dbg(DATA, "Enter\n");
 
 	skb_queue_walk_safe(skb_list, skb, pnext) {
 		skb_unlink(skb, skb_list);
@@ -779,6 +789,7 @@ struct brcmf_if *brcmf_add_if(struct brcmf_pub *drvr, s32 bssidx, s32 ifidx,
 	ifp->bssidx = bssidx;
 
 	init_waitqueue_head(&ifp->pend_8021x_wait);
+	spin_lock_init(&ifp->netif_stop_lock);
 
 	if (mac_addr != NULL)
 		memcpy(ifp->mac_addr, mac_addr, ETH_ALEN);
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +1 -1
index d248751..6f3d181 100644
@@ -2369,12 +2369,12 @@ static int brcmf_sdbrcm_bus_txdata(struct device *dev, struct sk_buff *pkt)
 	} else {
 		ret = 0;
 	}
-	spin_unlock_bh(&bus->txqlock);
 
 	if (pktq_len(&bus->txq) >= TXHI) {
 		bus->txoff = true;
 		brcmf_txflowblock(bus->sdiodev->dev, true);
 	}
+	spin_unlock_bh(&bus->txqlock);
 
 #ifdef DEBUG
 	if (pktq_plen(&bus->txq, prec) > qcount[prec])
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c +311 -327

1,292 lines not on this page · raw message

drivers/net/wireless/brcm80211/brcmfmac/fwsignal.h +1 -0
index fbe483d..9fc8609 100644
@@ -29,5 +29,6 @@ void brcmf_fws_reset_interface(struct brcmf_if *ifp);
 void brcmf_fws_add_interface(struct brcmf_if *ifp);
 void brcmf_fws_del_interface(struct brcmf_if *ifp);
 void brcmf_fws_bustxfail(struct brcmf_fws_info *fws, struct sk_buff *skb);
+void brcmf_fws_bus_blocked(struct brcmf_pub *drvr, bool flow_blocked);
 
 #endif /* FWSIGNAL_H_ */
drivers/net/wireless/brcm80211/brcmfmac/usb.c +8 -0
index 01aed7a..322cadc 100644
@@ -82,6 +82,7 @@ struct brcmf_usbdev_info {
 	int tx_high_watermark;
 	int tx_freecount;
 	bool tx_flowblock;
+	spinlock_t tx_flowblock_lock;
 
 	struct brcmf_usbreq *tx_reqs;
 	struct brcmf_usbreq *rx_reqs;
@@ -411,6 +412,7 @@ static void brcmf_usb_tx_complete(struct urb *urb)
 {
 	struct brcmf_usbreq *req = (struct brcmf_usbreq *)urb->context;
 	struct brcmf_usbdev_info *devinfo = req->devinfo;
+	unsigned long flags;
 
 	brcmf_dbg(USB, "Enter, urb->status=%d, skb=%p\n", urb->status,
 		  req->skb);
@@ -419,11 +421,13 @@ static void brcmf_usb_tx_complete(struct urb *urb)
 	brcmf_txcomplete(devinfo->dev, req->skb, urb->status == 0);
 	req->skb = NULL;
 	brcmf_usb_enq(devinfo, &devinfo->tx_freeq, req, &devinfo->tx_freecount);
+	spin_lock_irqsave(&devinfo->tx_flowblock_lock, flags);
 	if (devinfo->tx_freecount > devinfo->tx_high_watermark &&
 		devinfo->tx_flowblock) {
 		brcmf_txflowblock(devinfo->dev, false);
 		devinfo->tx_flowblock = false;
 	}
+	spin_unlock_irqrestore(&devinfo->tx_flowblock_lock, flags);
 }
 
 static void brcmf_usb_rx_complete(struct urb *urb)
@@ -568,6 +572,7 @@ static int brcmf_usb_tx(struct device *dev, struct sk_buff *skb)
 	struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(dev);
 	struct brcmf_usbreq  *req;
 	int ret;
+	unsigned long flags;
 
 	brcmf_dbg(USB, "Enter, skb=%p\n", skb);
 	if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) {
@@ -599,11 +604,13 @@ static int brcmf_usb_tx(struct device *dev, struct sk_buff *skb)
 		goto fail;
 	}
 
+	spin_lock_irqsave(&devinfo->tx_flowblock_lock, flags);
 	if (devinfo->tx_freecount < devinfo->tx_low_watermark &&
 	    !devinfo->tx_flowblock) {
 		brcmf_txflowblock(dev, true);
 		devinfo->tx_flowblock = true;
 	}
+	spin_unlock_irqrestore(&devinfo->tx_flowblock_lock, flags);
 	return 0;
 
 fail:
@@ -1164,6 +1171,7 @@ struct brcmf_usbdev *brcmf_usb_attach(struct brcmf_usbdev_info *devinfo,
 
 	/* Initialize the spinlocks */
 	spin_lock_init(&devinfo->qlock);
+	spin_lock_init(&devinfo->tx_flowblock_lock);
 
 	INIT_LIST_HEAD(&devinfo->rx_freeq);
 	INIT_LIST_HEAD(&devinfo->rx_postq);
drivers/net/wireless/brcm80211/brcmsmac/main.c +2 -15
index 28e7aee..9fd6f2f 100644
@@ -3074,21 +3074,8 @@ static void brcms_b_antsel_set(struct brcms_hardware *wlc_hw, u32 antsel_avail)
  */
 static bool brcms_c_ps_allowed(struct brcms_c_info *wlc)
 {
-	/* disallow PS when one of the following global conditions meets */
-	if (!wlc->pub->associated)
-		return false;
-
-	/* disallow PS when one of these meets when not scanning */
-	if (wlc->filter_flags & FIF_PROMISC_IN_BSS)
-		return false;
-
-	if (wlc->bsscfg->type == BRCMS_TYPE_AP)
-		return false;
-
-	if (wlc->bsscfg->type == BRCMS_TYPE_ADHOC)
-		return false;
-
-	return true;
+	/* not supporting PS so always return false for now */
+	return false;
 }
 
 static void brcms_c_statsupd(struct brcms_c_info *wlc)
drivers/net/wireless/mwifiex/debugfs.c +17 -5
index 753b568..a5f9875 100644
@@ -26,10 +26,17 @@
 static struct dentry *mwifiex_dfs_dir;
 
 static char *bss_modes[] = {
-	"Unknown",
-	"Ad-hoc",
-	"Managed",
-	"Auto"
+	"UNSPECIFIED",
+	"ADHOC",
+	"STATION",
+	"AP",
+	"AP_VLAN",
+	"WDS",
+	"MONITOR",
+	"MESH_POINT",
+	"P2P_CLIENT",
+	"P2P_GO",
+	"P2P_DEVICE",
 };
 
 /* size/addr for mwifiex_debug_info */
@@ -200,7 +207,12 @@ mwifiex_info_read(struct file *file, char __user *ubuf,
 	p += sprintf(p, "driver_version = %s", fmt);
 	p += sprintf(p, "\nverext = %s", priv->version_str);
 	p += sprintf(p, "\ninterface_name=\"%s\"\n", netdev->name);
-	p += sprintf(p, "bss_mode=\"%s\"\n", bss_modes[info.bss_mode]);
+
+	if (info.bss_mode >= ARRAY_SIZE(bss_modes))
+		p += sprintf(p, "bss_mode=\"%d\"\n", info.bss_mode);
+	else
+		p += sprintf(p, "bss_mode=\"%s\"\n", bss_modes[info.bss_mode]);
+
 	p += sprintf(p, "media_state=\"%s\"\n",
 		     (!priv->media_connected ? "Disconnected" : "Connected"));
 	p += sprintf(p, "mac_address=\"%pM\"\n", netdev->dev_addr);
drivers/net/wireless/rtlwifi/rtl8192cu/hw.c +100 -34

224 lines not on this page · raw message

drivers/net/wireless/rtlwifi/rtl8192cu/hw.h +0 -4
index f41a3aa..8e3ec1e 100644
@@ -98,10 +98,6 @@ void rtl92cu_update_interrupt_mask(struct ieee80211_hw *hw,
 				   u32 add_msr, u32 rm_msr);
 void rtl92cu_get_hw_reg(struct ieee80211_hw *hw, u8 variable, u8 *val);
 void rtl92cu_set_hw_reg(struct ieee80211_hw *hw, u8 variable, u8 *val);
-void rtl92cu_update_hal_rate_table(struct ieee80211_hw *hw,
-				   struct ieee80211_sta *sta,
-				   u8 rssi_level);
-void rtl92cu_update_hal_rate_mask(struct ieee80211_hw *hw, u8 rssi_level);
 
 void rtl92cu_update_channel_access_setting(struct ieee80211_hw *hw);
 bool rtl92cu_gpio_radio_on_off_checking(struct ieee80211_hw *hw, u8 * valid);
drivers/net/wireless/rtlwifi/rtl8192cu/mac.c +17 -1
index 85b6bdb..da4f587 100644
@@ -289,14 +289,30 @@ void rtl92c_set_key(struct ieee80211_hw *hw, u32 key_index,
 				macaddr = cam_const_broad;
 				entry_id = key_index;
 			} else {
+				if (mac->opmode == NL80211_IFTYPE_AP ||
+				    mac->opmode == NL80211_IFTYPE_MESH_POINT) {
+					entry_id = rtl_cam_get_free_entry(hw,
+								 p_macaddr);
+					if (entry_id >=  TOTAL_CAM_ENTRY) {
+						RT_TRACE(rtlpriv, COMP_SEC,
+							 DBG_EMERG,
+							 "Can not find free hw security cam entry\n");
+						return;
+					}
+				} else {
+					entry_id = CAM_PAIRWISE_KEY_POSITION;
+				}
+
 				key_index = PAIRWISE_KEYIDX;
-				entry_id = CAM_PAIRWISE_KEY_POSITION;
 				is_pairwise = true;
 			}
 		}
 		if (rtlpriv->sec.key_len[key_index] == 0) {
 			RT_TRACE(rtlpriv, COMP_SEC, DBG_DMESG,
 				 "delete one entry\n");
+			if (mac->opmode == NL80211_IFTYPE_AP ||
+			    mac->opmode == NL80211_IFTYPE_MESH_POINT)
+				rtl_cam_del_entry(hw, p_macaddr);
 			rtl_cam_delete_one_entry(hw, p_macaddr, entry_id);
 		} else {
 			RT_TRACE(rtlpriv, COMP_SEC, DBG_LOUD,
drivers/net/wireless/rtlwifi/rtl8192cu/sw.c +2 -2
index 938b1e6..826f085 100644
@@ -106,8 +106,7 @@ static struct rtl_hal_ops rtl8192cu_hal_ops = {
 	.update_interrupt_mask = rtl92cu_update_interrupt_mask,
 	.get_hw_reg = rtl92cu_get_hw_reg,
 	.set_hw_reg = rtl92cu_set_hw_reg,
-	.update_rate_tbl = rtl92cu_update_hal_rate_table,
-	.update_rate_mask = rtl92cu_update_hal_rate_mask,
+	.update_rate_tbl = rtl92cu_update_hal_rate_tbl,
 	.fill_tx_desc = rtl92cu_tx_fill_desc,
 	.fill_fake_txdesc = rtl92cu_fill_fake_txdesc,
 	.fill_tx_cmddesc = rtl92cu_tx_fill_cmddesc,
@@ -137,6 +136,7 @@ static struct rtl_hal_ops rtl8192cu_hal_ops = {
 	.phy_lc_calibrate = _rtl92cu_phy_lc_calibrate,
 	.phy_set_bw_mode_callback = rtl92cu_phy_set_bw_mode_callback,
 	.dm_dynamic_txpower = rtl92cu_dm_dynamic_txpower,
+	.fill_h2c_cmd = rtl92c_fill_h2c_cmd,
 };
 
 static struct rtl_mod_params rtl92cu_mod_params = {
drivers/net/wireless/rtlwifi/rtl8192cu/sw.h +3 -0
index a1310ab..262e1e4 100644
@@ -49,5 +49,8 @@ bool rtl92cu_phy_set_rf_power_state(struct ieee80211_hw *hw,
 u32 rtl92cu_phy_query_rf_reg(struct ieee80211_hw *hw,
 			    enum radio_path rfpath, u32 regaddr, u32 bitmask);
 void rtl92cu_phy_set_bw_mode_callback(struct ieee80211_hw *hw);
+void rtl92cu_update_hal_rate_tbl(struct ieee80211_hw *hw,
+				 struct ieee80211_sta *sta,
+				 u8 rssi_level);
 
 #endif
drivers/net/wireless/rtlwifi/usb.c +13 -0
index 76732b0..a3532e0 100644
@@ -824,6 +824,7 @@ static void rtl_usb_stop(struct ieee80211_hw *hw)
 
 	/* should after adapter start and interrupt enable. */
 	set_hal_stop(rtlhal);
+	cancel_work_sync(&rtlpriv->works.fill_h2c_cmd);
 	/* Enable software */
 	SET_USB_STOP(rtlusb);
 	rtl_usb_deinit(hw);
@@ -1026,6 +1027,16 @@ static bool rtl_usb_tx_chk_waitq_insert(struct ieee80211_hw *hw,
 	return false;
 }
 
+static void rtl_fill_h2c_cmd_work_callback(struct work_struct *work)
+{
+	struct rtl_works *rtlworks =
+	    container_of(work, struct rtl_works, fill_h2c_cmd);
+	struct ieee80211_hw *hw = rtlworks->hw;
+	struct rtl_priv *rtlpriv = rtl_priv(hw);
+
+	rtlpriv->cfg->ops->fill_h2c_cmd(hw, H2C_RA_MASK, 5, rtlpriv->rate_mask);
+}
+
 static struct rtl_intf_ops rtl_usb_ops = {
 	.adapter_start = rtl_usb_start,
 	.adapter_stop = rtl_usb_stop,
@@ -1057,6 +1068,8 @@ int rtl_usb_probe(struct usb_interface *intf,
 
 	/* this spin lock must be initialized early */
 	spin_lock_init(&rtlpriv->locks.usb_lock);
+	INIT_WORK(&rtlpriv->works.fill_h2c_cmd,
+		  rtl_fill_h2c_cmd_work_callback);
 
 	rtlpriv->usb_data_index = 0;
 	init_completion(&rtlpriv->firmware_loading_complete);
drivers/net/wireless/rtlwifi/wifi.h +4 -0
index 44328ba..cc03e7c 100644
@@ -1736,6 +1736,8 @@ struct rtl_hal_ops {
 	void (*bt_wifi_media_status_notify) (struct ieee80211_hw *hw,
 					     bool mstate);
 	void (*bt_coex_off_before_lps) (struct ieee80211_hw *hw);
+	void (*fill_h2c_cmd) (struct ieee80211_hw *hw, u8 element_id,
+			      u32 cmd_len, u8 *p_cmdbuffer);
 };
 
 struct rtl_intf_ops {
@@ -1869,6 +1871,7 @@ struct rtl_works {
 	struct delayed_work fwevt_wq;
 
 	struct work_struct lps_change_work;
+	struct work_struct fill_h2c_cmd;
 };
 
 struct rtl_debug {
@@ -2048,6 +2051,7 @@ struct rtl_priv {
 		};
 	};
 	bool enter_ps;	/* true when entering PS */
+	u8 rate_mask[5];
 
 	/*This must be the last item so
 	   that it points to the data allocated
include/net/bluetooth/hci_core.h +1 -0
index 35a57cd..7cb6d36 100644
@@ -1117,6 +1117,7 @@ void hci_sock_dev_event(struct hci_dev *hdev, int event);
 int mgmt_control(struct sock *sk, struct msghdr *msg, size_t len);
 int mgmt_index_added(struct hci_dev *hdev);
 int mgmt_index_removed(struct hci_dev *hdev);
+int mgmt_set_powered_failed(struct hci_dev *hdev, int err);
 int mgmt_powered(struct hci_dev *hdev, u8 powered);
 int mgmt_discoverable(struct hci_dev *hdev, u8 discoverable);
 int mgmt_connectable(struct hci_dev *hdev, u8 connectable);
include/net/bluetooth/mgmt.h +1 -0
index 22980a7..9944c3e 100644
@@ -42,6 +42,7 @@
 #define MGMT_STATUS_NOT_POWERED		0x0f
 #define MGMT_STATUS_CANCELLED		0x10
 #define MGMT_STATUS_INVALID_INDEX	0x11
+#define MGMT_STATUS_RFKILLED		0x12
 
 struct mgmt_hdr {
 	__le16	opcode;
net/bluetooth/hci_core.c +5 -1
index 33843c5..d817c93 100644
@@ -1555,11 +1555,15 @@ static const struct rfkill_ops hci_rfkill_ops = {
 static void hci_power_on(struct work_struct *work)
 {
 	struct hci_dev *hdev = container_of(work, struct hci_dev, power_on);
+	int err;
 
 	BT_DBG("%s", hdev->name);
 
-	if (hci_dev_open(hdev->id) < 0)
+	err = hci_dev_open(hdev->id);
+	if (err < 0) {
+		mgmt_set_powered_failed(hdev, err);
 		return;
+	}
 
 	if (test_bit(HCI_AUTO_OFF, &hdev->dev_flags))
 		queue_delayed_work(hdev->req_workqueue, &hdev->power_off,
net/bluetooth/l2cap_core.c +52 -18

202 lines not on this page · raw message

net/bluetooth/mgmt.c +22 -1
index 35fef22..f8ecbc7 100644
@@ -2700,7 +2700,7 @@ static int start_discovery(struct sock *sk, struct hci_dev *hdev,
 		break;
 
 	case DISCOV_TYPE_LE:
-		if (!lmp_host_le_capable(hdev)) {
+		if (!test_bit(HCI_LE_ENABLED, &hdev->dev_flags)) {
 			err = cmd_status(sk, hdev->id, MGMT_OP_START_DISCOVERY,
 					 MGMT_STATUS_NOT_SUPPORTED);
 			mgmt_pending_remove(cmd);
@@ -3418,6 +3418,27 @@ new_settings:
 	return err;
 }
 
+int mgmt_set_powered_failed(struct hci_dev *hdev, int err)
+{
+	struct pending_cmd *cmd;
+	u8 status;
+
+	cmd = mgmt_pending_find(MGMT_OP_SET_POWERED, hdev);
+	if (!cmd)
+		return -ENOENT;
+
+	if (err == -ERFKILL)
+		status = MGMT_STATUS_RFKILLED;
+	else
+		status = MGMT_STATUS_FAILED;
+
+	err = cmd_status(cmd->sk, hdev->id, MGMT_OP_SET_POWERED, status);
+
+	mgmt_pending_remove(cmd);
+
+	return err;
+}
+
 int mgmt_discoverable(struct hci_dev *hdev, u8 discoverable)
 {
 	struct cmd_lookup match = { NULL, hdev };
net/bluetooth/smp.c +2 -2
index b2296d3..b5562ab 100644
@@ -770,7 +770,7 @@ int smp_conn_security(struct hci_conn *hcon, __u8 sec_level)
 
 	BT_DBG("conn %p hcon %p level 0x%2.2x", conn, hcon, sec_level);
 
-	if (!lmp_host_le_capable(hcon->hdev))
+	if (!test_bit(HCI_LE_ENABLED, &hcon->hdev->dev_flags))
 		return 1;
 
 	if (sec_level == BT_SECURITY_LOW)
@@ -851,7 +851,7 @@ int smp_sig_channel(struct l2cap_conn *conn, struct sk_buff *skb)
 	__u8 reason;
 	int err = 0;
 
-	if (!lmp_host_le_capable(conn->hcon->hdev)) {
+	if (!test_bit(HCI_LE_ENABLED, &conn->hcon->hdev->dev_flags)) {
 		err = -ENOTSUPP;
 		reason = SMP_PAIRING_NOTSUPP;
 		goto done;
Signature · 2 lines
John W. Linville		Someday the world will need a hero, and you
[email protected]			might be all we have.  Be ready.
maintainer
#1 lore raw

From: "John W. Linville" <[email protected]>
Date: Mon, 3 Jun 2013 14:48:17 -0400

Quoted 1 line

Please let me know if there are problems!

Sorry, the broadcom brcmfmac changes need to go.

Some of those commits are cleanups, and some of them have the worst commit log messages ever, the last one for example:

0017-brcmsmac-fix-regression-observed-in-3.10-rc1.patch

has no explanation whatsoever of what the actual problem or regression is, what aspect of the logic in that function is causing the problem, and no explanation why making this function always return 'false' is a reasonable fix.

That entire series is of very low quality, and even if it was in good shape, at least half the changes are not appropriate at all this late in the -rc series.

#2 lore raw
Quoted 12 lines · David Miller

From: "John W. Linville" <[email protected]>
Date: Mon, 3 Jun 2013 14:48:17 -0400

Quoted 1 line

Please let me know if there are problems!

Sorry, the broadcom brcmfmac changes need to go.

Some of those commits are cleanups, and some of them have the worst commit log messages ever, the last one for example:

0017-brcmsmac-fix-regression-observed-in-3.10-rc1.patch

Quoted 8 lines

has no explanation whatsoever of what the actual problem or regression is, what aspect of the logic in that function is causing the problem, and no explanation why making this function always return 'false' is a reasonable fix.

That entire series is of very low quality, and even if it was in good shape, at least half the changes are not appropriate at all this late in the -rc series.

OK, sorry Dave -- I knew better...

John

Signature · 6 lines
John W. Linville		Someday the world will need a hero, and you
[email protected]			might be all we have.  Be ready.
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html