Skip to contentSkip to conversation

mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed

PATCH New Sreekanth Reddy 1 participant 1 message Jun 28, 2013

Subsystems (2)
SCSI LSI Logic MPT fusion drivers (FC/SAS/SPI)
lore
Share & tools
lore

Sreekanth Reddy

author
#0 lore raw

PATCH 6/7 mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed

When Async scanning mode is enabled and device scanning is in progress, devices should not be removed. But in actuality, devices are removed but their transport layer entries are not removed. This causes error to add the same device to the transport layer after host reset or diagnostic reset.

So, in this patch, modified the code in such a way that device is not removed when Async scanning mode is enabled and device scanning is in progress.

Signed-off-by Sreekanth Reddy <[email protected]>
---
 drivers/scsi/mpt3sas/mpt3sas_scsih.c |   22 +++++++++++++---------
 1 files changed, 13 insertions(+), 9 deletions(-)
drivers/scsi/mpt3sas/mpt3sas_scsih.c +13 -9
index 632eba7..8cbe8fd 100644
@@ -675,11 +675,12 @@ _scsih_sas_device_add(struct MPT3SAS_ADAPTER *ioc,
 		 * devices while scanning is turned on due to an oops in
 		 * scsi_sysfs_add_sdev()->add_device()->sysfs_addrm_start()
 		 */
-		if (!ioc->is_driver_loading)
+		if (!ioc->is_driver_loading) {
 			mpt3sas_transport_port_remove(ioc,
 			    sas_device->sas_address,
 			    sas_device->sas_address_parent);
-		_scsih_sas_device_remove(ioc, sas_device);
+			_scsih_sas_device_remove(ioc, sas_device);
+		}
 	}
 }
 

@@ -7531,10 +7532,12 @@ _scsih_probe_boot_devices(struct MPT3SAS_ADAPTER *ioc)
 		    sas_address_parent)) {
 			_scsih_sas_device_remove(ioc, sas_device);
 		} else if (!sas_device->starget) {
-			if (!ioc->is_driver_loading)
-				mpt3sas_transport_port_remove(ioc, sas_address,
+			if (!ioc->is_driver_loading) {
+				mpt3sas_transport_port_remove(ioc,
+				    sas_address,
 				    sas_address_parent);
-			_scsih_sas_device_remove(ioc, sas_device);
+				_scsih_sas_device_remove(ioc, sas_device);
+			}
 		}
 	}
 }

@@ -7590,13 +7593,14 @@ _scsih_probe_sas(struct MPT3SAS_ADAPTER *ioc)
 			 * oops in scsi_sysfs_add_sdev()->add_device()->
 			 * sysfs_addrm_start()
 			 */
-			if (!ioc->is_driver_loading)
+			if (!ioc->is_driver_loading) {
 				mpt3sas_transport_port_remove(ioc,
 				    sas_device->sas_address,
 				    sas_device->sas_address_parent);
-			list_del(&sas_device->list);
-			kfree(sas_device);
-			continue;
+				list_del(&sas_device->list);
+				kfree(sas_device);
+				continue;
+			}
 		}
 
 		spin_lock_irqsave(&ioc->sas_device_lock, flags);
Signature · 1 line
1.7.3