Skip to contentSkip to conversation

Some SuperH boards are broken

U-Boot Masahiro Yamada 2 participants 3 messages Nov 18, 2013

lore
Share & tools
lore
#0 lore raw

Hello Nobuhiro

I cannot compile sh7752evb and sh7757lcr boards
because of the following error:

sh_eth.c: In function 'sh_eth_send':
sh_eth.c:57:2: warning: implicit declaration of function 'dcache_wback_range' [-Wimplicit-function-declaration] drivers/net/built-in.o: In function `sh_eth_send':
/home/masahiro/u-boot-log/u-boot-4/drivers/net/sh_eth.c:87: undefined reference to dcache_wback_range' drivers/net/built-in.o: In function sh_eth_rx_desc_init':
/home/masahiro/u-boot-log/u-boot-4/drivers/net/sh_eth.c:276: undefined reference to `dcache_wback_range'

I grepped the whole tree and the definition of "dcache_wback_range" function is surely missing.

Unfortunately, no board maintainter is assigned for these two boards. Could you fix them?
Or if you can't fix this issue, please both of the two boards.

And we have newly another warning message:

time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000 and should not be defined by platforms" [-Wcpp] for rsk7203, rsk7264, rsk7269 boards.

We need to fix boards which use CONFIG_SYS_HZ other than 1000.

Best Regards
Masahiro Yamada

#1 lore raw

Hi,

2013/11/18 Masahiro Yamada <[email protected]>:

Quoted 13 lines

Hello Nobuhiro

I cannot compile sh7752evb and sh7757lcr boards
because of the following error:

sh_eth.c: In function 'sh_eth_send':
sh_eth.c:57:2: warning: implicit declaration of function 'dcache_wback_range' [-Wimplicit-function-declaration] drivers/net/built-in.o: In function `sh_eth_send':
/home/masahiro/u-boot-log/u-boot-4/drivers/net/sh_eth.c:87: undefined reference to dcache_wback_range' drivers/net/built-in.o: In function sh_eth_rx_desc_init':
/home/masahiro/u-boot-log/u-boot-4/drivers/net/sh_eth.c:276: undefined reference to `dcache_wback_range'

Quoted 8 lines

I grepped the whole tree and the definition of "dcache_wback_range" function is surely missing.

Unfortunately, no board maintainter is assigned for these two boards. Could you fix them?
Or if you can't fix this issue, please both of the two boards.

Yes , I know. And I already send patches to net maintainer.
http://patchwork.ozlabs.org/patch/268947/

But these are not applied.

Quoted 7 lines

And we have newly another warning message:

time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000 and should not be defined by platforms" [-Wcpp] for rsk7203, rsk7264, rsk7269 boards.

We need to fix boards which use CONFIG_SYS_HZ other than 1000.

Yes , I know too.
I am working about this.

Quoted 4 lines

Best Regards
Masahiro Yamada

Best regards,
Nobuhiro

#2 lore raw

Hello Nobuhiro.

Quoted 9 lines
Quoted 8 lines

I grepped the whole tree and the definition of "dcache_wback_range" function is surely missing.

Unfortunately, no board maintainter is assigned for these two boards. Could you fix them?
Or if you can't fix this issue, please both of the two boards.

Quoted 4 lines

Yes , I know. And I already send patches to net maintainer.
http://patchwork.ozlabs.org/patch/268947/

But these are not applied.

This patch worked for me. Thanks.

Quoted 10 lines
Quoted 7 lines

And we have newly another warning message:

time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000 and should not be defined by platforms" [-Wcpp] for rsk7203, rsk7264, rsk7269 boards.

We need to fix boards which use CONFIG_SYS_HZ other than 1000.

Yes , I know too.
I am working about this.

That's OK, then.
Sorry for noise.

Best Regards
Masahiro Yamada