Skip to contentSkip to conversation

ixgbe driver fails occasionally since ee98b577e7711d5890ded2c7b05578a29512bd39

DISCUSSION Scott Harrison 2 participants 4 messages Oct 23, 2014 – Oct 24, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hi,

I was asked to raise this issue here.

https://bugzilla.kernel.org/show_bug.cgi?id=86591

lspci ->

03:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) 03:00.1 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01)

With the fibre 10Gbs SFP occasionally on reboot we get

[   15.104726] ixgbe 0000:03:00.0 eth0: detected SFP+: 5                        [   19.735155] ixgbe 0000:03:00.0 eth0: setup link failed with code -14  

Probably about 1 in 10 boots. With the 1Gbs Copper SFP it works fine. kernel 3.14.8 worked fine, but on upgrading to 3.16.1 it fails in this way. I have narrowed it down to the commit

https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/commit/?id=ee98b577e7711d5890ded2c7b05578a29512bd39

I don't know enough about the hardware to understand why the change sometimes causes the failure, and was hoping someone else would. Reverting this commit on 3.16.1 fixes the issue.

If you need any more information please ask.

Scott.

Signature · 8 lines
Software Engineer

Cisco.com - http://www.cisco.com

This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorised to receive for the recipient), please contact the sender by reply email and delete all copies of this message.

For corporate legal information go to:
http://www.cisco.com/web/about/doing_business/legal/cri/index.html
#1 lore raw
Quoted 15 lines

-----Original Message-----
From: [email protected] [mailto:netdev-
[email protected]] On Behalf Of Scott Harrison
Sent: Thursday, October 23, 2014 7:06 AM
To: [email protected]
Subject: ixgbe driver fails occasionally since ee98b577e7711d5890ded2c7b05578a29512bd39

Hi,

I was asked to raise this issue here.

https://bugzilla.kernel.org/show_bug.cgi?id=86591

lspci ->

Quoted 7 lines

03:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) 03:00.1 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01)

With the fibre 10Gbs SFP occasionally on reboot we get

[   15.104726] ixgbe 0000:03:00.0 eth0: detected SFP+: 5
[   19.735155] ixgbe 0000:03:00.0 eth0: setup link failed with code -14

The error message is from an ethtool command. Where you trying to set the speed to a certain value?

Thanks,
Emil

#2 lore raw

Emil,

Sorry, I should have looked harder it happens as part of ifup eth0, we have "/sbin/ethtool -s eth0 autoneg on" in the interfaces file.

HTH.

Scott.

Quoted 28 lines · Emil S
Quoted 15 lines

-----Original Message-----
From: [email protected] [mailto:netdev-
[email protected]] On Behalf Of Scott Harrison
Sent: Thursday, October 23, 2014 7:06 AM
To: [email protected]
Subject: ixgbe driver fails occasionally since ee98b577e7711d5890ded2c7b05578a29512bd39

Hi,

I was asked to raise this issue here.

https://bugzilla.kernel.org/show_bug.cgi?id=86591

lspci ->

Quoted 7 lines

03:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) 03:00.1 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01)

With the fibre 10Gbs SFP occasionally on reboot we get

[   15.104726] ixgbe 0000:03:00.0 eth0: detected SFP+: 5
[   19.735155] ixgbe 0000:03:00.0 eth0: setup link failed with code -14

The error message is from an ethtool command. Where you trying to set the speed to a certain value?

Thanks,
Emil

Signature · 8 lines
Software Engineer

Cisco.com - http://www.cisco.com

This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorised to receive for the recipient), please contact the sender by reply email and delete all copies of this message.

For corporate legal information go to:
http://www.cisco.com/web/about/doing_business/legal/cri/index.html
#3 lore raw
Quoted 11 lines

-----Original Message-----
From: Scott Harrison [mailto:[email protected]]
Sent: Friday, October 24, 2014 2:18 AM
To: Tantilov, Emil S
Cc: [email protected]
Subject: Re: ixgbe driver fails occasionally since ee98b577e7711d5890ded2c7b05578a29512bd39

Emil,

Sorry, I should have looked harder it happens as part of ifup eth0, we have "/sbin/ethtool -s eth0 autoneg on" in the interfaces file.

Well you can avoid this issue by removing this command since it is not needed for anything. The interface will auto-negotiate by default.

We were able to reproduce this issue and will work on a fix.

Thanks a lot for reporting it.

Emil

Quoted 4 lines

HTH.

Scott.