ixgbe: add support for WoL and autoneg FC for some X550 devices
Subsystems (2)
PATCH 1/11 ixgbe: add support for WoL and autoneg FC for some X550 devices
These Device ID could support both WoL and autoneg flow control. In the case of WoL this is indicated by the eeprom. This patch enables these devices this support.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 2 ++ drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 4 ++++ 2 files changed, 6 insertions(+)
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +2 -0
@@ -96,6 +96,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)case IXGBE_DEV_ID_82599_T3_LOM :case IXGBE_DEV_ID_X540T :case IXGBE_DEV_ID_X540T1 : +case IXGBE_DEV_ID_X550T : +case IXGBE_DEV_ID_X550EM_X_10G_T : supported = true;break ;default :
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +4 -0
@@ -8317,6 +8317,10 @@ int ixgbe_wol_supported(struct ixgbe_adapter *adapter, u16 device_id,break ;case IXGBE_DEV_ID_X540T :case IXGBE_DEV_ID_X540T1 : +case IXGBE_DEV_ID_X550T : +case IXGBE_DEV_ID_X550EM_X_KX4 : +case IXGBE_DEV_ID_X550EM_X_KR : +case IXGBE_DEV_ID_X550EM_X_10G_T :/* check eeprom to see if enabled wol */ if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) || ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
PATCH 2/11 ixgbe: add define for X557 Phy ID
Add a define for the new PHY identification as well as it's mapping to the correct PHY type. Also allow ethtool to identify this type as well.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 3 +++ drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 1 + 3 files changed, 5 insertions(+)
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c +1 -0
@@ -207,6 +207,7 @@ static int ixgbe_get_settings(struct net_device *netdev,switch (adapter->hw.phy.type) {case ixgbe_phy_tn:case ixgbe_phy_aq: +case ixgbe_phy_x550em_ext_t:case ixgbe_phy_cu_unknown: ecmd->supported |=SUPPORTED_TP ; ecmd->advertising |=ADVERTISED_TP ;
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c +3 -0
@@ -356,6 +356,9 @@ static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id)case ATH_PHY_ID : phy_type = ixgbe_phy_nl;break ; +case X557_PHY_ID : + phy_type = ixgbe_phy_x550em_ext_t; +break ;default : phy_type = ixgbe_phy_unknown;break ;
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +1 -0
@@ -1334,6 +1334,7 @@ struct ixgbe_thermal_sensor_data {#define TN1010_PHY_ID 0x00A19410#define TNX_FW_REV 0xB#define X540_PHY_ID 0x01540200 +#define X557_PHY_ID 0x01540240#define QT2022_PHY_ID 0x0043A400#define ATH_PHY_ID 0x03429050#define AQ_FW_REV 0x20
PATCH 3/11 ixgbe: Add a PHY power state method
In reply to Don SkidmoreThis new method will control the PHY power state. You pass in the state you wish to change to (ether on or off). For cases where this method is not used the current PHY power state behavior is maintained.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c | 2 + drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 15 +++++++++++ drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 34 ++++++++++++++++++++++++ drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 3 ++ drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 1 + 7 files changed, 56 insertions(+), 1 deletion(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c +1 -1
@@ -1225,7 +1225,7 @@ static struct ixgbe_phy_operations phy_ops_82598 = { .setup_link_speed = &ixgbe_setup_phy_link_speed_generic, .read_i2c_sff8472 = &ixgbe_read_i2c_sff8472_82598, .read_i2c_eeprom = &ixgbe_read_i2c_eeprom_82598, - .check_overtemp = &ixgbe_tn_check_overtemp, + .check_overtemp = &ixgbe_tn_check_overtemp, };struct ixgbe_info ixgbe_82598_info = {
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +15 -0
@@ -4898,6 +4898,9 @@ static void ixgbe_up_complete(struct ixgbe_adapter *adapter)if (hw->mac.ops.enable_tx_laser) hw->mac.ops.enable_tx_laser (hw); +if (hw->phy.ops.set_phy_power) + hw->phy.ops.set_phy_power (hw, true); +smp_mb__before_atomic ();clear_bit (__IXGBE_DOWN, &adapter->state);ixgbe_napi_enable_all (adapter);
@@ -5017,6 +5020,13 @@ void ixgbe_reset(struct ixgbe_adapter *adapter)if (test_bit (__IXGBE_PTP_RUNNING, &adapter->state))ixgbe_ptp_reset (adapter); + +if (hw->phy.ops.set_phy_power) { +if (!netif_running (adapter->netdev) && !adapter->wol) + hw->phy.ops.set_phy_power (hw, false); +else + hw->phy.ops.set_phy_power (hw, true); + } }/**
@@ -5697,6 +5707,7 @@ static int ixgbe_change_mtu(struct net_device *netdev, int new_mtu)static int ixgbe_open (struct net_device *netdev) {struct ixgbe_adapter *adapter =netdev_priv (netdev); +struct ixgbe_hw *hw = &adapter->hw;int err, queues;/* disallow open during test */
@@ -5754,6 +5765,8 @@ err_set_queues:ixgbe_free_irq (adapter); err_req_irq:ixgbe_free_all_rx_resources (adapter); +if (hw->phy.ops.set_phy_power && !adapter->wol) + hw->phy.ops.set_phy_power (&adapter->hw, false); err_setup_rx:ixgbe_free_all_tx_resources (adapter); err_setup_tx:
@@ -5914,6 +5927,8 @@ static int __ixgbe_shutdown(struct pci_dev *pdev, bool *enable_wake) } *enable_wake = !!wufc; +if (hw->phy.ops.set_phy_power && !*enable_wake) + hw->phy.ops.set_phy_power (hw, false);ixgbe_release_hw_control (adapter);
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c +34 -0
@@ -2140,3 +2140,37 @@ s32 ixgbe_tn_check_overtemp(struct ixgbe_hw *hw)return IXGBE_ERR_OVERTEMP ; } + +/** ixgbe_set_copper_phy_power - Control power for copper phy +* @hw: pointer to hardware structure +* @on: true for on, false for off +**/ +s32 ixgbe_set_copper_phy_power (struct ixgbe_hw *hw,bool on) +{ +u32 status; +u16 reg; + +/* Bail if we don't have copper phy */ +if (hw->mac.ops.get_media_type (hw) != ixgbe_media_type_copper) +return 0 ; + + status = hw->phy.ops.read_reg (hw,IXGBE_MDIO_VENDOR_SPECIFIC_1_CONTROL , +IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE , + ®); +if (status) +return status; + +if (on) { + reg &= ~IXGBE_MDIO_PHY_SET_LOW_POWER_MODE ; + }else { +if (ixgbe_check_reset_blocked (hw)) +return 0 ; + reg |=IXGBE_MDIO_PHY_SET_LOW_POWER_MODE ; + } + + status = hw->phy.ops.write_reg (hw,IXGBE_MDIO_VENDOR_SPECIFIC_1_CONTROL , +IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE , + reg); +return status; +} +
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h +1 -0
@@ -145,6 +145,7 @@ s32 ixgbe_get_phy_firmware_version_generic(struct ixgbe_hw *hw, u16 *firmware_version);s32 ixgbe_reset_phy_nl (struct ixgbe_hw *hw); +s32 ixgbe_set_copper_phy_power (struct ixgbe_hw *hw,bool on);s32 ixgbe_identify_module_generic (struct ixgbe_hw *hw);s32 ixgbe_identify_sfp_module_generic (struct ixgbe_hw *hw); s32 ixgbe_get_sfp_init_sequence_offsets(struct ixgbe_hw *hw,
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +3 -0
@@ -1309,6 +1309,8 @@ struct ixgbe_thermal_sensor_data {#define IXGBE_MDIO_AUTO_NEG_LP 0x13/* AUTO_NEG LP Status Reg */ #define IXGBE_MDIO_AUTO_NEG_EEE_ADVT 0x3C/* AUTO_NEG EEE Advt Reg */ +#define IXGBE_MDIO_PHY_SET_LOW_POWER_MODE 0x0800/* Set low power mode */ +#define IXGBE_MDIO_TX_VENDOR_ALARMS_3 0xCC02/* Vendor Alarms 3 Reg */ #define IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK 0x3/* PHY Reset Complete Mask */ #define IXGBE_MDIO_GLOBAL_RES_PR_10 0xC479/* Global Resv Provisioning 10 Reg */
@@ -3277,6 +3279,7 @@ struct ixgbe_phy_operations {s32 (*read_i2c_combined)(struct ixgbe_hw *,u8 addr,u16 reg,u16 *val);s32 (*write_i2c_combined)(struct ixgbe_hw *,u8 addr,u16 reg,u16 val);s32 (*check_overtemp)(struct ixgbe_hw *); +s32 (*set_phy_power)(struct ixgbe_hw *,bool on); };struct ixgbe_eeprom_info {
drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c +1 -0
@@ -850,6 +850,7 @@ static struct ixgbe_phy_operations phy_ops_X540 = { .read_i2c_eeprom = &ixgbe_read_i2c_eeprom_generic, .write_i2c_eeprom = &ixgbe_write_i2c_eeprom_generic, .check_overtemp = &ixgbe_tn_check_overtemp, + .set_phy_power = &ixgbe_set_copper_phy_power, .get_firmware_version = &ixgbe_get_phy_firmware_version_generic, };
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +1 -0
@@ -1530,6 +1530,7 @@ static struct ixgbe_phy_operations phy_ops_X550 = { .setup_link = &ixgbe_setup_phy_link_generic, .read_i2c_combined = &ixgbe_read_i2c_combined_generic, .write_i2c_combined = &ixgbe_write_i2c_combined_generic, + .set_phy_power = &ixgbe_set_copper_phy_power, };static struct ixgbe_phy_operations phy_ops_X550EM_x = {
PATCH 4/11 ixgbe: Restore ESDP settings after MAC reset
In reply to Don SkidmoreThe I2C mux control relies on the SDP setting in the ESDP register so it is necessary to restore the value after a MAC reset. Combine all this functionality in to a support function.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 38 ++++++++++++++----------- 1 file changed, 21 insertions(+), 17 deletions(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +21 -17
@@ -26,6 +26,22 @@#include "ixgbe_common.h" #include "ixgbe_phy.h" +/** ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control +* @hw: pointer to hardware structure +**/ +static void ixgbe_setup_mux_ctl (struct ixgbe_hw *hw) +{ +u32 esdp =IXGBE_READ_REG (hw,IXGBE_ESDP ); + +if (hw->bus.lan_id) { + esdp &= ~(IXGBE_ESDP_SDP1_NATIVE |IXGBE_ESDP_SDP1 ); + esdp |=IXGBE_ESDP_SDP1_DIR ; + } + esdp &= ~(IXGBE_ESDP_SDP0_NATIVE |IXGBE_ESDP_SDP0_DIR ); +IXGBE_WRITE_REG (hw,IXGBE_ESDP , esdp); +IXGBE_WRITE_FLUSH (hw); +} +/** ixgbe_identify_phy_x550em - Get PHY type based on device id * @hw: pointer to hardware structure *
@@ -33,18 +49,11 @@*/ static s32 ixgbe_identify_phy_x550em (struct ixgbe_hw *hw) { -u32 esdp =IXGBE_READ_REG (hw,IXGBE_ESDP ); -switch (hw->device_id) {case IXGBE_DEV_ID_X550EM_X_SFP :/* set up for CS4227 usage */ hw->phy.phy_semaphore_mask =IXGBE_GSSR_SHARED_I2C_SM ; -if (hw->bus.lan_id) { - esdp &= ~(IXGBE_ESDP_SDP1_NATIVE |IXGBE_ESDP_SDP1 ); - esdp |=IXGBE_ESDP_SDP1_DIR ; - } - esdp &= ~(IXGBE_ESDP_SDP0_NATIVE |IXGBE_ESDP_SDP0_DIR ); -IXGBE_WRITE_REG (hw,IXGBE_ESDP , esdp); +ixgbe_setup_mux_ctl (hw);return ixgbe_identify_module_generic (hw);case IXGBE_DEV_ID_X550EM_X_KX4 :
@@ -1127,18 +1136,10 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) {struct ixgbe_phy_info *phy = &hw->phy;s32 ret_val; -u32 esdp;if (hw->device_id ==IXGBE_DEV_ID_X550EM_X_SFP ) { - esdp =IXGBE_READ_REG (hw,IXGBE_ESDP ); phy->phy_semaphore_mask =IXGBE_GSSR_SHARED_I2C_SM ; - -if (hw->bus.lan_id) { - esdp &= ~(IXGBE_ESDP_SDP1_NATIVE |IXGBE_ESDP_SDP1 ); - esdp |=IXGBE_ESDP_SDP1_DIR ; - } - esdp &= ~(IXGBE_ESDP_SDP0_NATIVE |IXGBE_ESDP_SDP0_DIR ); -IXGBE_WRITE_REG (hw,IXGBE_ESDP , esdp); +ixgbe_setup_mux_ctl (hw); }/* Identify the PHY or SFP module */
@@ -1366,6 +1367,9 @@ mac_reset_top: hw->mac.num_rar_entries =128 ; hw->mac.ops.init_rx_addrs (hw); +if (hw->device_id ==IXGBE_DEV_ID_X550EM_X_SFP ) +ixgbe_setup_mux_ctl (hw); +return status; }
PATCH 5/11 ixgbe: add X550 support for external PHY and forced 1G/10G support
In reply to Don SkidmoreThis patch adds x550 external PHY interrupt and forced 1G/10G support. This included enabling and handling LSC and thermal sensor interrupt. ixgbe_handle_lasi() has been added for handling the interrupts received over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable mask and check interrupt flags for the external PHY.
Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em. ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY to either iXFI (10G) or KX (1G) based on the user selected auto advertised link speed setting. Then sets up the external PHY auto advertised link speed.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 22 + drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 611 ++++++++++++++++++------- 2 files changed, 473 insertions(+), 160 deletions(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +22 -0
@@ -1305,6 +1305,8 @@ struct ixgbe_thermal_sensor_data {#define IXGBE_MDIO_AUTO_NEG_CONTROL 0x0/* AUTO_NEG Control Reg */ #define IXGBE_MDIO_AUTO_NEG_STATUS 0x1/* AUTO_NEG Status Reg */ #define IXGBE_MDIO_AUTO_NEG_VENDOR_STAT 0xC800/* AUTO_NEG Vendor Status Reg */ +#define IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM2 0xCC01/* AUTO_NEG Vendor Tx Reg */ +#define IXGBE_MDIO_AUTO_NEG_VEN_LSC 0x1/* AUTO_NEG Vendor Tx LSC */ #define IXGBE_MDIO_AUTO_NEG_ADVT 0x10/* AUTO_NEG Advt Reg */ #define IXGBE_MDIO_AUTO_NEG_LP 0x13/* AUTO_NEG LP Status Reg */ #define IXGBE_MDIO_AUTO_NEG_EEE_ADVT 0x3C/* AUTO_NEG EEE Advt Reg */
@@ -1315,10 +1317,26 @@ struct ixgbe_thermal_sensor_data {#define IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK 0x3/* PHY Reset Complete Mask */ #define IXGBE_MDIO_GLOBAL_RES_PR_10 0xC479/* Global Resv Provisioning 10 Reg */ #define IXGBE_MDIO_POWER_UP_STALL 0x8000/* Power Up Stall */ +#define IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK 0xFF00/* int std mask */ +#define IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG 0xFC00/* chip std int flag */ +#define IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK 0xFF01/* int chip-wide mask */ +#define IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_FLAG 0xFC01/* int chip-wide mask */ +#define IXGBE_MDIO_GLOBAL_ALARM_1 0xCC00/* Global alarm 1 */ +#define IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL 0x4000/* high temp failure */ +#define IXGBE_MDIO_GLOBAL_INT_MASK 0xD400/* Global int mask */ +#define IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN 0x1000/* autoneg vendor alarm +* int enable +*/ +#define IXGBE_MDIO_GLOBAL_ALARM_1_INT 0x4/* int in Global alarm 1 */ +#define IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN 0x1/* vendor alarm int enable */ +#define IXGBE_MDIO_GLOBAL_STD_ALM2_INT 0x200/* vendor alarm2 int mask */ +#define IXGBE_MDIO_GLOBAL_INT_HI_TEMP_EN 0x4000/* int high temp enable */ #define IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR 0xC30A/* PHY_XS SDA/SCL Addr Reg */ #define IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA 0xC30B/* PHY_XS SDA/SCL Data Reg */ #define IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT 0xC30C/* PHY_XS SDA/SCL Stat Reg */ +#define IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK 0xD401/* PHY TX Vendor LASI */ +#define IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN 0x1/* PHY TX Vendor LASI enable */ #define IXGBE_MDIO_PMD_STD_TX_DISABLE_CNTR 0x9/* Standard Tx Dis Reg */ #define IXGBE_MDIO_PMD_GLOBAL_TX_DISABLE 0x0001/* PMD Global Tx Dis */
@@ -3280,6 +3298,7 @@ struct ixgbe_phy_operations {s32 (*write_i2c_combined)(struct ixgbe_hw *,u8 addr,u16 reg,u16 val);s32 (*check_overtemp)(struct ixgbe_hw *);s32 (*set_phy_power)(struct ixgbe_hw *,bool on); +s32 (*handle_lasi)(struct ixgbe_hw *hw); };struct ixgbe_eeprom_info {
@@ -3341,6 +3360,7 @@ struct ixgbe_phy_info {bool multispeed_fiber;bool reset_if_overtemp;bool qsfp_shared_i2c_bus; +u32 nw_mng_if_sel; };#include "ixgbe_mbx.h"
@@ -3509,4 +3529,6 @@ struct ixgbe_info {#define IXGBE_SB_IOSF_TARGET_KX4_PCS0 2#define IXGBE_SB_IOSF_TARGET_KX4_PCS1 3 +#define IXGBE_NW_MNG_IF_SEL 0x00011178 +#define IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE BIT(24)#endif /* _IXGBE_TYPE_H_ */
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +451 -160
681 lines not on this page · raw message
PATCH 6/11 ixgbe: Add reset for X550 device
In reply to Don SkidmoreThis patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which allows devices that have LASI support in enable their interrupt.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +17 -0
@@ -1385,6 +1385,22 @@ s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw)return ixgbe_setup_ixfi_x550em (hw, &force_speed); } +/** ixgbe_reset_phy_t_X550em - Performs X557 PHY reset and enables LASI +* @hw: pointer to hardware structure +**/ +static s32 ixgbe_reset_phy_t_X550em (struct ixgbe_hw *hw) +{ +s32 status; + + status =ixgbe_reset_phy_generic (hw); + +if (status) +return status; + +/* Configure Link Status Alarm and Temperature Threshold interrupts */ +return ixgbe_enable_lasi_ext_t_x550em (hw); +} +/** ixgbe_init_phy_ops_X550em - PHY/SFP specific init * @hw: pointer to hardware structure *
@@ -1454,6 +1470,7 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) } phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em; + phy->ops.reset = ixgbe_reset_phy_t_X550em;break ;default :break ;
PATCH 7/11 ixgbe: Add const string for overheat message
In reply to Don SkidmoreThe over heat message is displayed for mutliple reasons but the text is cut-n-pasted for each of these cases. This patch pulls the text from the same location. I noticed this as I am about to add anothere case.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 15 +++++++-------- 1 file changed, 7 insertions(+), 8 deletions(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +7 -8
@@ -81,6 +81,11 @@ const char ixgbe_driver_version[] = DRV_VERSION;static const char ixgbe_copyright[] ="Copyright (c) 1999-2014 Intel Corporation." ; +static const char ixgbe_overheat_msg[] = +"Network adapter has been stopped because it has over heated. " +"Restart the computer. If the problem persists, " +"power off the system and replace the adapter" ; +static const struct ixgbe_info *ixgbe_info_tbl[] = { [board_82598] = &ixgbe_82598_info, [board_82599] = &ixgbe_82599_info,
@@ -2407,10 +2412,7 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)return ;break ; } -e_crit (drv, -"Network adapter has been stopped because it has over heated. " -"Restart the computer. If the problem persists, " -"power off the system and replace the adapter\n" ); +e_crit (drv,"%s\n" , ixgbe_overheat_msg); adapter->interrupt_event =0 ; }
@@ -2457,10 +2459,7 @@ static void ixgbe_check_overtemp_event(struct ixgbe_adapter *adapter, u32 eicr)return ; } -e_crit (drv, -"Network adapter has been stopped because it has over heated. " -"Restart the computer. If the problem persists, " -"power off the system and replace the adapter\n" ); +e_crit (drv,"%s\n" , ixgbe_overheat_msg); }static void ixgbe_check_sfp_event (struct ixgbe_adapter *adapter,u32 eicr)
PATCH 8/11 ixgbe: add support for interrupts from X550 external PHY
In reply to Don SkidmoreFrom: Don Skidmore <[email protected]>
This patch adds support for receiving interrupts from a external copper PHY for the X550 part. This includes enabling, detection as well as re-enablement.
--- drivers/net/ethernet/intel/ixgbe/ixgbe.h | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 32 +++++++++++++++++++++++++ 2 files changed, 33 insertions(+)
drivers/net/ethernet/intel/ixgbe/ixgbe.h +1 -0
@@ -645,6 +645,7 @@ struct ixgbe_adapter {#define IXGBE_FLAG2_RSS_FIELD_IPV4_UDP (u32)(1 << 8)#define IXGBE_FLAG2_RSS_FIELD_IPV6_UDP (u32)(1 << 9)#define IXGBE_FLAG2_PTP_PPS_ENABLED (u32)(1 << 10) +#define IXGBE_FLAG2_PHY_INTERRUPT (u32)(1 << 11)/* Tx fast path data */ int num_tx_queues;
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +32 -0
@@ -2408,6 +2408,8 @@ static void ixgbe_check_overtemp_subtask(struct ixgbe_adapter *adapter)break ;default : +if (adapter->hw.mac.type >= ixgbe_mac_X540) +return ;if (!(eicr &IXGBE_EICR_GPI_SDP0 (hw)))return ;break ;
@@ -2592,6 +2594,8 @@ static inline void ixgbe_irq_enable(struct ixgbe_adapter *adapter, bool queues,case ixgbe_mac_X540:case ixgbe_mac_X550:case ixgbe_mac_X550EM_x: +if (adapter->hw.phy.type == ixgbe_phy_x550em_ext_t) + mask |=IXGBE_EICR_GPI_SDP0_X540 ; mask |=IXGBE_EIMS_ECC ; mask |=IXGBE_EIMS_MAILBOX ;break ;
@@ -2646,6 +2650,13 @@ static irqreturn_t ixgbe_msix_other(int irq, void *data)case ixgbe_mac_X540:case ixgbe_mac_X550:case ixgbe_mac_X550EM_x: +if (hw->phy.type == ixgbe_phy_x550em_ext_t && + (eicr &IXGBE_EICR_GPI_SDP0_X540 )) { + adapter->flags2 |=IXGBE_FLAG2_PHY_INTERRUPT ; +ixgbe_service_event_schedule (adapter); +IXGBE_WRITE_REG (hw,IXGBE_EICR , +IXGBE_EICR_GPI_SDP0_X540 ); + }if (eicr &IXGBE_EICR_ECC ) {e_info (link,"Received ECC Err, initiating reset\n" ); adapter->flags2 |=IXGBE_FLAG2_RESET_REQUESTED ;
@@ -6757,6 +6768,26 @@ static void ixgbe_service_timer(unsigned long data)ixgbe_service_event_schedule (adapter); } +static void ixgbe_phy_interrupt_subtask (struct ixgbe_adapter *adapter) +{ +struct ixgbe_hw *hw = &adapter->hw; +u32 status; + +if (!(adapter->flags2 &IXGBE_FLAG2_PHY_INTERRUPT )) +return ; + + adapter->flags2 &= ~IXGBE_FLAG2_PHY_INTERRUPT ; + +if (!hw->phy.ops.handle_lasi) +return ; + + status = hw->phy.ops.handle_lasi (&adapter->hw); +if (status !=IXGBE_ERR_OVERTEMP ) +return ; + +e_crit (drv,"%s\n" , ixgbe_overheat_msg); +} +static void ixgbe_reset_subtask (struct ixgbe_adapter *adapter) {if (!(adapter->flags2 &IXGBE_FLAG2_RESET_REQUESTED ))
@@ -6798,6 +6829,7 @@ static void ixgbe_service_task(struct work_struct *work)return ; }ixgbe_reset_subtask (adapter); +ixgbe_phy_interrupt_subtask (adapter);ixgbe_sfp_detection_subtask (adapter);ixgbe_sfp_link_config_subtask (adapter);ixgbe_check_overtemp_subtask (adapter);
PATCH 9/11 ixgbe: fix issue with sfp events with new X550 devices
In reply to Don SkidmoreAdd checks for systems that don't have SFP's to avoid incorrectly acting on interrupts that are falsely interpreted as SFP events. We do this by updating the ixgbe_is_sfp to be aware of the new X550 devices. This also includes a modified check generating the EICR mask to be more forward-looking.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 62 +++++++++++++------------ 1 file changed, 33 insertions(+), 29 deletions(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +33 -29
@@ -2464,20 +2464,50 @@ static void ixgbe_check_overtemp_event(struct ixgbe_adapter *adapter, u32 eicr)e_crit (drv,"%s\n" , ixgbe_overheat_msg); } +static inline bool ixgbe_is_sfp (struct ixgbe_hw *hw) +{ +switch (hw->mac.type) { +case ixgbe_mac_82598EB: +if (hw->phy.type == ixgbe_phy_nl) +return true; +return false; +case ixgbe_mac_82599EB: +case ixgbe_mac_X550EM_x: +switch (hw->mac.ops.get_media_type (hw)) { +case ixgbe_media_type_fiber: +case ixgbe_media_type_fiber_qsfp: +return true; +default : +return false; + } +default : +return false; + } +} +static void ixgbe_check_sfp_event (struct ixgbe_adapter *adapter,u32 eicr) {struct ixgbe_hw *hw = &adapter->hw; +u32 eicr_mask =IXGBE_EICR_GPI_SDP2 (hw); + +if (!ixgbe_is_sfp (hw)) +return ; + +/* Later MAC's use different SDP */ +if (hw->mac.type >= ixgbe_mac_X540) + eicr_mask =IXGBE_EICR_GPI_SDP0_X540 ; -if (eicr &IXGBE_EICR_GPI_SDP2 (hw)) { +if (eicr & eicr_mask) {/* Clear the interrupt */ -IXGBE_WRITE_REG (hw,IXGBE_EICR ,IXGBE_EICR_GPI_SDP2 (hw)); +IXGBE_WRITE_REG (hw,IXGBE_EICR , eicr_mask);if (!test_bit (__IXGBE_DOWN, &adapter->state)) { adapter->flags2 |=IXGBE_FLAG2_SFP_NEEDS_RESET ;ixgbe_service_event_schedule (adapter); } } -if (eicr &IXGBE_EICR_GPI_SDP1 (hw)) { +if (adapter->hw.mac.type == ixgbe_mac_82599EB && + (eicr &IXGBE_EICR_GPI_SDP1 (hw))) {/* Clear the interrupt */ IXGBE_WRITE_REG (hw,IXGBE_EICR ,IXGBE_EICR_GPI_SDP1 (hw));if (!test_bit (__IXGBE_DOWN, &adapter->state)) {
@@ -4738,32 +4768,6 @@ static void ixgbe_configure(struct ixgbe_adapter *adapter)ixgbe_configure_dfwd (adapter); } -static inline bool ixgbe_is_sfp (struct ixgbe_hw *hw) -{ -switch (hw->phy.type) { -case ixgbe_phy_sfp_avago: -case ixgbe_phy_sfp_ftl: -case ixgbe_phy_sfp_intel: -case ixgbe_phy_sfp_unknown: -case ixgbe_phy_sfp_passive_tyco: -case ixgbe_phy_sfp_passive_unknown: -case ixgbe_phy_sfp_active_unknown: -case ixgbe_phy_sfp_ftl_active: -case ixgbe_phy_qsfp_passive_unknown: -case ixgbe_phy_qsfp_active_unknown: -case ixgbe_phy_qsfp_intel: -case ixgbe_phy_qsfp_unknown: -/* ixgbe_phy_none is set when no SFP module is present */ -case ixgbe_phy_none: -return true; -case ixgbe_phy_nl: -if (hw->mac.type == ixgbe_mac_82598EB) -return true; -default : -return false; - } -} -/** * ixgbe_sfp_link_config - set up SFP+ link * @adapter: pointer to private adapter struct
PATCH 10/11 ixgbe: fix bug in not clearing counters for X550 devices
In reply to Don SkidmoreThis check was missed in when this new MAC type was added. Since these counts can be incremented for X550 we need to clear them.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +1 -1
@@ -470,7 +470,7 @@ s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) } } -if (hw->mac.type == ixgbe_mac_X540) { +if (hw->mac.type == ixgbe_mac_X540 || hw->mac.type == ixgbe_mac_X540) {if (hw->phy.id ==0 ) hw->phy.ops.identify (hw); hw->phy.ops.read_reg (hw,IXGBE_PCRC8ECL ,MDIO_MMD_PCS , &i);
PATCH 11/11 ixgbe: Add support for another X550 device.
In reply to Don SkidmoreFrom: Don Skidmore <[email protected]>
This patch adds support for another 10baseT X550 device.
--- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 1 + drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 7 +++++++ 4 files changed, 10 insertions(+)
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +1 -0
@@ -136,6 +136,7 @@ static const struct pci_device_id ixgbe_pci_tbl[] = { {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550T), board_X550}, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_KX4), board_X550EM_x}, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_KR), board_X550EM_x}, + {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_10G_T), board_X550EM_x},/* required last entry */ {0, } };
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c +1 -0
@@ -347,6 +347,7 @@ static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id)case TN1010_PHY_ID : phy_type = ixgbe_phy_tn;break ; +case X550_PHY_ID :case X540_PHY_ID : phy_type = ixgbe_phy_aq;break ;
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +1 -0
@@ -1354,6 +1354,7 @@ struct ixgbe_thermal_sensor_data {#define TN1010_PHY_ID 0x00A19410#define TNX_FW_REV 0xB#define X540_PHY_ID 0x01540200 +#define X550_PHY_ID 0x01540220#define X557_PHY_ID 0x01540240#define QT2022_PHY_ID 0x0043A400#define ATH_PHY_ID 0x03429050
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c +7 -0
@@ -1591,6 +1591,7 @@ static s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw)s32 status;u32 ctrl =0 ;u32 i; +u32 hlreg0;bool link_up = false;/* Call adapter stop to disable Tx/Rx and clear interrupts */
@@ -1675,6 +1676,12 @@ mac_reset_top: hw->mac.num_rar_entries =128 ; hw->mac.ops.init_rx_addrs (hw); +if (hw->device_id ==IXGBE_DEV_ID_X550EM_X_10G_T ) { + hlreg0 =IXGBE_READ_REG (hw,IXGBE_HLREG0 ); + hlreg0 &= ~IXGBE_HLREG0_MDCSPD ; +IXGBE_WRITE_REG (hw,IXGBE_HLREG0 , hlreg0); + } +if (hw->device_id ==IXGBE_DEV_ID_X550EM_X_SFP )ixgbe_setup_mux_ctl (hw);