Skip to contentSkip to conversation

ath10k drivers on t1024 freescale board

DISCUSSION B R Manjula 2 participants 10 messages Jan 12, 2016 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we downloaded the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

what could be the reason.
please reply as early as possible we are struck..

regards,
manjula

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw

kernel being used is 3.12
---------- Forwarded Message -----------
From: "B R Manjula" <[email protected]>
To: [email protected]
Sent: Tue, 12 Jan 2016 12:35:31 +0530
Subject: ath10k drivers on t1024 freescale board

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we downloaded the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

what could be the reason.
please reply as early as possible we are struck..

regards,
manjula

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t
------- End of Forwarded Message -------

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#2 lore raw
In reply to B R Manjula
Quoted 29 lines · B R Manjula

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we downloaded the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

Quoted 1 line

what could be the reason.

You can't just go about and use FW API2 firmware as FW API1 one. No wonder device crashed.

Also you can't just place any file instead of otp.bin.

Moreover you're using an arcane version of ath10k. It's wasteful if you're going to report problems that were already fixed. Please upgrade the kernel or use backports:

https://wireless.wiki.kernel.org/en/users/drivers/ath10k/backports

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#3 lore raw

There are so many releases which one is suitable for our linux kernel 3.12

On Tue, 12 Jan 2016 09:04:57 +0100, Michal Kazior wrote

Quoted 5 lines · B R Manjula
Quoted 4 lines

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we

downloaded

Quoted 36 lines
Quoted 25 lines

the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

Quoted 1 line

what could be the reason.

You can't just go about and use FW API2 firmware as FW API1 one. No wonder device crashed.

Also you can't just place any file instead of otp.bin.

Moreover you're using an arcane version of ath10k. It's wasteful if you're going to report problems that were already fixed. Please upgrade the kernel or use backports:

Quoted 8 lines

https://wireless.wiki.kernel.org/en/users/drivers/ath10k/backports

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#4 lore raw
In reply to Michal Kazior

Thanks for your input which version of the backport to be taken for kernel 3.12

backports-4.2.6-1 signed
backports-4.1.1-1 signed
backports-4.0.1-1 signed
backports-3.19-rc1-1 signed
backports-3.18.1-1 signed
backports-3.17.1-1 signed
backports-3.16.2-1 signed
backports-3.15.9-1 signed
backports-3.14-1 signed
backports-3.12.8-1 signed
backports-3.10.19-1 signed

where do we get otp.bin file

On Tue, 12 Jan 2016 09:04:57 +0100, Michal Kazior wrote

Quoted 5 lines · B R Manjula
Quoted 4 lines

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we

downloaded

Quoted 36 lines
Quoted 25 lines

the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

Quoted 1 line

what could be the reason.

You can't just go about and use FW API2 firmware as FW API1 one. No wonder device crashed.

Also you can't just place any file instead of otp.bin.

Moreover you're using an arcane version of ath10k. It's wasteful if you're going to report problems that were already fixed. Please upgrade the kernel or use backports:

Quoted 8 lines

https://wireless.wiki.kernel.org/en/users/drivers/ath10k/backports

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#7 lore raw
In reply to Michal Kazior

Please can you provide useful links to cross-compilation we are getting issues while cross-compiling for target:

Though I am cross-compiling it is giving following error:

The conf is not executing on the host:

make defconfig-ath10k
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o conf.o conf.c
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o zconf.tab.o zconf.tab.c
In file included from zconf.tab.c:2503:0:
menu.c: In function 'get_symbol_str':
menu.c:561:18: warning: 'jump' may be used uninitialized in this function [-Wmaybe- uninitialized]

     jump->offset = r->len - 1;
                  ^
menu.c:515:19: note: 'jump' was declared here
  struct jump_key *jump;
                   ^

powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl-
networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux conf.o zconf.tab.o -o conf
./kconf/conf: ./kconf/conf: cannot execute binary file make[1]: *** [defconfig-ath10k] Error 126
make: *** [defconfig-ath10k] Error 2

On Tue, 12 Jan 2016 09:04:57 +0100, Michal Kazior wrote

Quoted 5 lines · B R Manjula
Quoted 4 lines

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we

downloaded

Quoted 36 lines
Quoted 25 lines

the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

Quoted 1 line

what could be the reason.

You can't just go about and use FW API2 firmware as FW API1 one. No wonder device crashed.

Also you can't just place any file instead of otp.bin.

Moreover you're using an arcane version of ath10k. It's wasteful if you're going to report problems that were already fixed. Please upgrade the kernel or use backports:

Quoted 8 lines

https://wireless.wiki.kernel.org/en/users/drivers/ath10k/backports

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#5 lore raw
In reply to B R Manjula
Quoted 13 lines · B R Manjula

Thanks for your input which version of the backport to be taken for kernel 3.12

backports-4.2.6-1       signed
backports-4.1.1-1       signed
backports-4.0.1-1       signed
backports-3.19-rc1-1    signed
backports-3.18.1-1      signed
backports-3.17.1-1      signed
backports-3.16.2-1      signed
backports-3.15.9-1      signed
backports-3.14-1        signed
backports-3.12.8-1      signed
backports-3.10.19-1     signed

All of them should work. That's how backports work:

https://backports.wiki.kernel.org/index.php/Documentation

Quoted 1 line

where do we get otp.bin file

You don't. It's embedded in FW API2 firmware blobs. FW API1 is very old and I would discourage using a driver which requires it. FYI You can still get it either by extracting it or using older git checkout:

https://github.com/kvalo/ath10k-firmware/tree/9374d42c01bd84487855af9f9bffc622c50e7331/ath10k/QCA988X/hw2.0

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#8 lore raw
In reply to B R Manjula
Quoted 23 lines · B R Manjula

Please can you provide useful links to cross-compilation we are getting issues while cross-compiling for target:

Though I am cross-compiling it is giving following error:

The conf is not executing on the host:

make defconfig-ath10k
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o conf.o conf.c
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o zconf.tab.o zconf.tab.c
In file included from zconf.tab.c:2503:0:
menu.c: In function 'get_symbol_str':
menu.c:561:18: warning: 'jump' may be used uninitialized in this function [-Wmaybe- uninitialized]

     jump->offset = r->len - 1;
                  ^
menu.c:515:19: note: 'jump' was declared here
  struct jump_key *jump;
                   ^
Quoted 5 lines

powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl-
networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux conf.o zconf.tab.o -o conf
./kconf/conf: ./kconf/conf: cannot execute binary file make[1]: *** [defconfig-ath10k] Error 126
make: *** [defconfig-ath10k] Error 2

I'm no cross-compilation expert. At best I can refer you to:

https://backports.wiki.kernel.org/index.php/Documentation/packaging

The "cannot execute binary file" can mean:
- invalid libc linking
- missing +x permissions on file (unlikely)
- missing +x permissions on filesystem (e.g. due to "noexec" mount option)
- trying to run a binary destined to a different arch

You'll have to figure it out yourself.

As an alternative you might want to use QEMU and do emulated native compilation (e.g. Debian with deboostrap) but I will not go into detail how to do this as it's not trivial.

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#9 lore raw
In reply to Michal Kazior

Please can you provide useful links to cross-compilation we are getting issues while cross-compiling for target:

Though I am cross-compiling it is giving following error:

The conf is not executing on the host:

make defconfig-ath10k
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o conf.o conf.c
powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl- networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux -Wall -Wmissing-prototypes -
Wstrict-prototypes -O2 -fomit-frame-pointer -c -o zconf.tab.o zconf.tab.c
In file included from zconf.tab.c:2503:0:
menu.c: In function 'get_symbol_str':
menu.c:561:18: warning: 'jump' may be used uninitialized in this function [-Wmaybe- uninitialized]

     jump->offset = r->len - 1;
                  ^
menu.c:515:19: note: 'jump' was declared here
  struct jump_key *jump;
                   ^

powerpc64-fsl-linux-gcc -mhard-float -m64 -mcpu=e5500 --sysroot=/opt/fsl-
networking/QorIQ-SDK-V1.7/sysroots/ppc64e5500-fsl-linux conf.o zconf.tab.o -o conf
./kconf/conf: ./kconf/conf: cannot execute binary file make[1]: *** [defconfig-ath10k] Error 126
make: *** [defconfig-ath10k] Error 2

On Tue, 12 Jan 2016 09:04:57 +0100, Michal Kazior wrote

Quoted 5 lines · B R Manjula
Quoted 4 lines

Hello ,

We are using kernel 3.11 on FREESCALE reference board T1024RDB-64bit board trying to bringup ath10k drivers we are using WLE-900VX-7AA (11ac pcie mini card) we

downloaded

Quoted 36 lines
Quoted 25 lines

the
firmware from the following site:
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/main/firmware-
2.bin_999.999.0.636
replaced as firmware.bin in the directory /lib/firmware/ath10k/QCA988X/hw2.0

board.bin is downloaded from
https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/board.bin

and otp.bin was not found we just placed some file in the name as otp.bin

we are getting the following issue:

ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath10k: MSI-X didn't succeed (1), trying MSI
ath10k: MSI interrupt handling
ath10k: Hardware name qca988x hw2.0 version 0x4100016c
ath10k: early firmware event indicated
ath10k: unable to write to the device
ath10k: could not write otp (-110)
ath10k: could not init core (-110)
ath10k: could not probe fw (-110)
ath10k: could not register driver core (-110)
ath10k_pci: probe of 0000:01:00.0 failed with error -110

Quoted 1 line

what could be the reason.

You can't just go about and use FW API2 firmware as FW API1 one. No wonder device crashed.

Also you can't just place any file instead of otp.bin.

Moreover you're using an arcane version of ath10k. It's wasteful if you're going to report problems that were already fixed. Please upgrade the kernel or use backports:

Quoted 8 lines

https://wireless.wiki.kernel.org/en/users/drivers/ath10k/backports

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#6 lore raw
In reply to Michal Kazior

thanks for input...

On Tue, 12 Jan 2016 13:02:29 +0100, Michal Kazior wrote

Quoted 19 lines · B R Manjula
Quoted 13 lines

Thanks for your input which version of the backport to be taken for kernel 3.12

backports-4.2.6-1       signed
backports-4.1.1-1       signed
backports-4.0.1-1       signed
backports-3.19-rc1-1    signed
backports-3.18.1-1      signed
backports-3.17.1-1      signed
backports-3.16.2-1      signed
backports-3.15.9-1      signed
backports-3.14-1        signed
backports-3.12.8-1      signed
backports-3.10.19-1     signed

All of them should work. That's how backports work:

https://backports.wiki.kernel.org/index.php/Documentation

Quoted 7 lines
Quoted 1 line

where do we get otp.bin file

You don't. It's embedded in FW API2 firmware blobs. FW API1 is very old and I would discourage using a driver which requires it. FYI You can still get it either by extracting it or using older git checkout:

https://github.com/kvalo/ath10k-

firmware/tree/9374d42c01bd84487855af9f9bffc622c50e7331/ath10k/QCA988X/hw2.0

Quoted 7 lines

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed.  If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. The sender does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail t

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k