Issue with ATH10K driver with 802.11 a/g mode datarates
Hi,
When we are testing 802.11 a/g mode throughput measurements on T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we are getting 26-27 Mbps , which is not meeting the required TEC specification (which is ~28 Mbps). How can we increase the throughput in these modes.
Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
Ben
Quoted 38 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we are getting 26-27 Mbps , which is not meeting the required TEC specification (which is ~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Signature · 8 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
... and what's "TEC specification" ?
-
a
Quoted 65 lines · Ben Greear
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
BenQuoted 41 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on
T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we
are getting 26-27 Mbps , which is not meeting the required TEC specification (which is
~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely
for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any
action in reliance on the contents of this information is strictly prohibited. The
sender does not aQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com
Quoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Hi,
I didnt try with ath9k drivers on the same setup.
we are using WiFi capacity test tool on Lanforge to test the performance, this will
generate the traffic. we are selecting the UDP protocol (packet - 1472 Bytes).
As per TEC spec. required data rates are given below.
Mode Asso. rate Throughput
802.11a 54 Mbps 28 Mbps
802.11g 54 Mbps 28 Mbps
But we are getting only 26-27Mbps, how to improve this throughput ?
[TEC(Telecommunication Engineering Centre, Govt. India) is a technical body,
prepares specification of common Telecom standards.]
Regards,
Sridhar
On Mon, 19 Sep 2016 10:22:26 -0700, Adrian Chadd wrote
Quoted 76 lines
.... and what's "TEC specification" ?
-
aQuoted 65 lines · Ben Greear
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
BenQuoted 41 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on
T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we
are getting 26-27 Mbps , which is not meeting the required TEC specification (which is
~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely
for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any
action in reliance on the contents of this information is strictly prohibited. The
sender does not aQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.comQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
LANforge is going to be running a modified driver and firmware, though likely it is no worse at performance in this case than stock code.
What is the device under test?
And, are you in an isolation chamber, using SMA cables, attenuation, etc?
There are lots of things that can impact wifi throughput so you have to provide lots more details in order for anyone to understand why the throughput might be less than expected.
And if it is specific to LANforge, please send email to [email protected]
Thanks,
Ben
Quoted 127 lines · Sridhar Konabathini
Hi,
I didnt try with ath9k drivers on the same setup.we are using WiFi capacity test tool on Lanforge to test the performance, this will
generate the traffic. we are selecting the UDP protocol (packet - 1472 Bytes).As per TEC spec. required data rates are given below.
Mode Asso. rate Throughput
802.11a 54 Mbps 28 Mbps
802.11g 54 Mbps 28 Mbps
But we are getting only 26-27Mbps, how to improve this throughput ?
[TEC(Telecommunication Engineering Centre, Govt. India) is a technical body,
prepares specification of common Telecom standards.]Regards,
SridharOn Mon, 19 Sep 2016 10:22:26 -0700, Adrian Chadd wrote
Quoted 76 lines
.... and what's "TEC specification" ?
-
aQuoted 65 lines · Ben Greear
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
BenQuoted 41 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on
T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we
are getting 26-27 Mbps , which is not meeting the required TEC specification (which is
~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely
for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any
action in reliance on the contents of this information is strictly prohibited. The
sender does not aQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.comQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kRegards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a
Signature · 7 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Hi,
Yes, we are doing the testing in an isolation chamber (no attenuators used), antennas
are connected to RF card via SMA cable. Tx power is 5dBm. we are not suspecting Lanforge as it gives required throughput in different WiFi setup.
here Device Under test is T2014 based card.
Regards,
Sridhar
On Mon, 19 Sep 2016 21:33:03 -0700, Ben Greear wrote
Quoted 11 lines
LANforge is going to be running a modified driver and firmware, though likely it is no worse at performance in this case than stock code.
What is the device under test?
And, are you in an isolation chamber, using SMA cables, attenuation, etc?
There are lots of things that can impact wifi throughput so you have to provide lots more details in order for anyone to understand why the throughput might be less than expected.
Quoted 10 lines
And if it is specific to LANforge, please send email to [email protected]
Thanks,
BenQuoted 4 lines · Sridhar Konabathini
Hi,
I didnt try with ath9k drivers on the same setup.we are using WiFi capacity test tool on Lanforge to test the performance, this
will
Quoted 113 lines
Quoted 113 lines
generate the traffic. we are selecting the UDP protocol (packet - 1472 Bytes).
As per TEC spec. required data rates are given below.
Mode Asso. rate Throughput
802.11a 54 Mbps 28 Mbps
802.11g 54 Mbps 28 Mbps
But we are getting only 26-27Mbps, how to improve this throughput ?
[TEC(Telecommunication Engineering Centre, Govt. India) is a technical body,
prepares specification of common Telecom standards.]Regards,
SridharOn Mon, 19 Sep 2016 10:22:26 -0700, Adrian Chadd wrote
Quoted 76 lines
.... and what's "TEC specification" ?
-
aQuoted 65 lines · Ben Greear
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
BenQuoted 41 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on
T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we
are getting 26-27 Mbps , which is not meeting the required TEC specification (which is
~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely
for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any
action in reliance on the contents of this information is strictly prohibited. The
sender does not aQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.comQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kRegards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.
Quoted 19 lines
Quoted 10 lines
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not aSignature · 7 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
You normally need to add 30-60 db of attenuation to get best throughput when directly cabling with SMA cables. Please try adding more attenuation.
What firmware are you using on the T1024RDB? Maybe also try using a different firmware version to see if that helps.
Thanks,
Ben
Quoted 187 lines · Sridhar Konabathini
Hi,
Yes, we are doing the testing in an isolation chamber (no attenuators used), antennas
are connected to RF card via SMA cable. Tx power is 5dBm. we are not suspecting Lanforge as it gives required throughput in different WiFi setup.
here Device Under test is T2014 based card.Regards,
SridharOn Mon, 19 Sep 2016 21:33:03 -0700, Ben Greear wrote
Quoted 11 lines
LANforge is going to be running a modified driver and firmware, though likely it is no worse at performance in this case than stock code.
What is the device under test?
And, are you in an isolation chamber, using SMA cables, attenuation, etc?
There are lots of things that can impact wifi throughput so you have to provide lots more details in order for anyone to understand why the throughput might be less than expected.
Quoted 10 lines
And if it is specific to LANforge, please send email to [email protected]
Thanks,
BenQuoted 4 lines · Sridhar Konabathini
Hi,
I didnt try with ath9k drivers on the same setup.we are using WiFi capacity test tool on Lanforge to test the performance, this
will
Quoted 124 lines
Quoted 113 lines
generate the traffic. we are selecting the UDP protocol (packet - 1472 Bytes).
As per TEC spec. required data rates are given below.
Mode Asso. rate Throughput
802.11a 54 Mbps 28 Mbps
802.11g 54 Mbps 28 Mbps
But we are getting only 26-27Mbps, how to improve this throughput ?
[TEC(Telecommunication Engineering Centre, Govt. India) is a technical body,
prepares specification of common Telecom standards.]Regards,
SridharOn Mon, 19 Sep 2016 10:22:26 -0700, Adrian Chadd wrote
Quoted 76 lines
.... and what's "TEC specification" ?
-
aQuoted 65 lines · Ben Greear
Out of curiosity, does ath9k perform at the required rates in a similar setup?
Sending tcp, udp, or some other protocol? How are you generating the traffic?
Thanks,
BenQuoted 41 lines · Sridhar Kondabathini
Hi,
When we are testing 802.11 a/g mode throughput measurements on
T1024RDB ( we used
kernel-3.12; ath10k drivers backported from 4.4;hostapd 2.5 for 11AC support), then we
are getting 26-27 Mbps , which is not meeting the required TEC specification (which is
~28 Mbps). How can we increase the throughput in these modes.Can you please help on this.
Regards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely
for
the use of the individual or entity to whom they are addressed. If you are not the
intended recipient you are notified that disclosing, copying, distributing or taking
any
action in reliance on the contents of this information is strictly prohibited. The
sender does not aQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.comQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kQuoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kRegards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Quoted 10 lines
Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not aQuoted 8 lines
--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10kRegards,
Sridhar Kondabathini,
Research engineer,
PSG lab,
Center for Development Of Telematics
9480484821.Disclaimer:
----------
This email and any files transmitted with it are confidential and intended solely for
the use of the individual or entity to whom they are addressed. If you are not the intended recipient you are notified that disclosing, copying, distributing or taking any
action in reliance on the contents of this information is strictly prohibited. The sender does not a
Signature · 7 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k