DisplayPort audio support on Cherrytrail
Subsystems (3)
cover DisplayPort audio support on Cherrytrail
Hi,
the following patches enable DisplayPort Audio on Cherrytrail machines when applied on top of my topic/intel-lpe-audio branch. Tests of DP audio were run on Dell Wyse 3040. The regression test were performed on Baytrail (Compute Stick) and Cherrytrail (Zotac PI330) in HDMI mode. On Cherrytrail there were no issues changing between HDMI and DP connectors dynamically.
Could you i915 people review and give ACK if they are OK? The changes in drm/i915 side are fairly trivial, so I'd like to take them through sound git tree once after I receive your ACKs.
Changes since RFC:
- reordered and squashed patches
- clean-up of register definitions and offsets (based on feedback from Jani/Ville)
- unmute amp for both HDMI and DP unconditionally
- mute amp on invalid ELD (unplug)
- remove test for chicken bit which seems to have no effect in hardware
- cosmetic edits to make checkpatch happy
- change i915 notification argument to pass the plataform device instead
Most of hard work in this patchset has been done by Pierre, so all credits go to him.
thanks,
Takashi
===
Pierre-Louis Bossart (4):
drm/i915: add DP support in LPE audio mode drm/i915: add DisplayPort amp unmute for LPE audio mode
ALSA: x86: intel_hdmi: add definitions and logic for DP audio
ALSA: x86: Use config base depending on the pipe
Takashi Iwai (3):
drm/i915: Avoid MST pipe handling for LPE audio drm/i915: Pass pipe to LPE audio notification drm/i915: Pass platform device to LPE audio notifier
drivers/gpu/drm/i915/i915_drv.h | 3 +- drivers/gpu/drm/i915/i915_reg.h | 10 ++ drivers/gpu/drm/i915/intel_audio.c | 38 +++++--- drivers/gpu/drm/i915/intel_lpe_audio.c | 28 +++++- include/drm/intel_lpe_audio.h | 7 +- sound/x86/intel_hdmi_audio.c | 173 ++++++++++++++++++++++++++++----- sound/x86/intel_hdmi_audio.h | 8 +- sound/x86/intel_hdmi_lpe_audio.c | 83 ++++++++++++---- sound/x86/intel_hdmi_lpe_audio.h | 29 ++++++ 9 files changed, 315 insertions(+), 64 deletions(-)
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 1/7 drm/i915: add DP support in LPE audio mode
From: Pierre-Louis Bossart <[email protected]>
If DisplayPort is detected, pass flag and link rate to audio driver
--- drivers/gpu/drm/i915/i915_drv.h | 3 ++- drivers/gpu/drm/i915/intel_audio.c | 19 +++++++++++++++---- drivers/gpu/drm/i915/intel_lpe_audio.c | 7 ++++++- include/drm/intel_lpe_audio.h | 2 ++ 4 files changed, 25 insertions(+), 6 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +2 -1
@@ -3401,7 +3401,8 @@ int intel_lpe_audio_init(struct drm_i915_private *dev_priv);void intel_lpe_audio_teardown (struct drm_i915_private *dev_priv);void intel_lpe_audio_irq_handler (struct drm_i915_private *dev_priv);void intel_lpe_audio_notify (struct drm_i915_private *dev_priv, -void *eld,int port,int tmds_clk_speed); +void *eld,int port,int tmds_clk_speed, +bool dp_output,int link_rate);/* intel_i2c.c */ extern int intel_setup_gmbus (struct drm_device *dev);
drivers/gpu/drm/i915/intel_audio.c +15 -4
@@ -631,9 +631,20 @@ void intel_audio_codec_enable(struct intel_encoder *intel_encoder,if (acomp && acomp->audio_ops && acomp->audio_ops->pin_eld_notify) acomp->audio_ops->pin_eld_notify (acomp->audio_ops->audio_ptr, (int ) port, (int ) pipe); - -intel_lpe_audio_notify (dev_priv, connector->eld, port, - crtc_state->port_clock); +switch (intel_encoder->type) { +case INTEL_OUTPUT_HDMI : +intel_lpe_audio_notify (dev_priv, connector->eld, port, + crtc_state->port_clock, + false,0 ); +break ; +case INTEL_OUTPUT_DP : +intel_lpe_audio_notify (dev_priv, connector->eld, port, + adjusted_mode->crtc_clock, + true, crtc_state->port_clock); +break ; +default : +break ; + } }/**
@@ -668,7 +679,7 @@ void intel_audio_codec_disable(struct intel_encoder *intel_encoder) acomp->audio_ops->pin_eld_notify (acomp->audio_ops->audio_ptr, (int ) port, (int ) pipe); -intel_lpe_audio_notify (dev_priv,NULL , port,0 ); +intel_lpe_audio_notify (dev_priv,NULL , port,0 , false,0 ); }/**
drivers/gpu/drm/i915/intel_lpe_audio.c +6 -1
@@ -332,7 +332,8 @@ void intel_lpe_audio_teardown(struct drm_i915_private *dev_priv)* Notify lpe audio driver of eld change. */ void intel_lpe_audio_notify (struct drm_i915_private *dev_priv, -void *eld,int port,int tmds_clk_speed) +void *eld,int port,int tmds_clk_speed, +bool dp_output,int link_rate) {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ;
@@ -351,12 +352,16 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->eld.port_id = port; pdata->hdmi_connected = true; + pdata->dp_output = dp_output;if (tmds_clk_speed) pdata->tmds_clock_speed = tmds_clk_speed; +if (link_rate) + pdata->link_rate = link_rate; }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; + pdata->dp_output = false; }if (pdata->notify_audio_lpe)
include/drm/intel_lpe_audio.h +2 -0
@@ -38,6 +38,8 @@ struct intel_hdmi_lpe_audio_pdata {bool notify_pending;int tmds_clock_speed;bool hdmi_connected; +bool dp_output; +int link_rate;struct intel_hdmi_lpe_audio_eld eld;void (*notify_audio_lpe)(void *audio_ptr);spinlock_t lpe_audio_slock;
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/7 drm/i915: add DisplayPort amp unmute for LPE audio mode
In reply to Takashi IwaiFrom: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38 prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.
--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 17 +++++++++++++++++ 2 files changed, 27 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +10 -0
@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)
drivers/gpu/drm/i915/intel_lpe_audio.c +17 -0
@@ -337,15 +337,25 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ; +u32 audio_enable; +i915_reg_t mmio;if (!HAS_LPE_AUDIO (dev_priv))return ; +if (port ==PORT_A ) { +DRM_ERROR ("PORT_A is not valid for HDMI/DP usages\n" ); +return ; + } + pdata =dev_get_platdata ( &(dev_priv->lpe_audio.platdev->dev));spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + mmio =VLV_AUD_PORT_EN_DBG (port); + audio_enable =I915_READ (mmio); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );
@@ -357,11 +367,18 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 45 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.Signed-off-by Pierre-Louis Bossart <[email protected]>Signed-off-by Takashi Iwai <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 17 +++++++++++++++++ 2 files changed, 27 insertions(+)drivers/gpu/drm/i915/i915_reg.h +10
-0@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)drivers/gpu/drm/i915/intel_lpe_audio.c +0
-0@@ -337,15 +337,25 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ;
drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, · line 349
Quoted 10 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +6
-0+u32 audio_enable; +i915_reg_t mmio;if (!HAS_LPE_AUDIO (dev_priv))return ; +if (port ==PORT_A ) { +DRM_ERROR ("PORT_A is not valid for HDMI/DP usages\n" ); +return ; + }
Port A doesn't exists on these platforms at all. So this is just dead code.
drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, · line 356
Quoted 7 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +2
-0+ pdata =dev_get_platdata ( &(dev_priv->lpe_audio.platdev->dev));spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + mmio =VLV_AUD_PORT_EN_DBG (port);
I'm not a fan of these temporary reg offset variables. Makes it hard to figure out later which register is being frobbed, especially when the variable name doesn't say what it actually is (like in this case). So I'd like to see this killed off.
Quoted 26 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +9
-0+ audio_enable =I915_READ (mmio); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );@@ -357,11 +367,18 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)Signature · 1 line
2.11.0
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 65 lines · Ville Syrjälä
Quoted 45 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.Signed-off-by Pierre-Louis Bossart <[email protected]>Signed-off-by Takashi Iwai <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 17 +++++++++++++++++ 2 files changed, 27 insertions(+)drivers/gpu/drm/i915/i915_reg.h +10
-0@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)drivers/gpu/drm/i915/intel_lpe_audio.c +0
-0@@ -337,15 +337,25 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ;drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, · line 349
Quoted 10 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +6
-0+u32 audio_enable; +i915_reg_t mmio;if (!HAS_LPE_AUDIO (dev_priv))return ; +if (port ==PORT_A ) { +DRM_ERROR ("PORT_A is not valid for HDMI/DP usages\n" ); +return ; + }Port A doesn't exists on these platforms at all. So this is just dead code.
Quoted 4 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +1
-0+ pdata =dev_get_platdata ( &(dev_priv->lpe_audio.platdev->dev));
Quoted 8 lines
drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, · line 356
Quoted 3 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +1
-0spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + mmio =VLV_AUD_PORT_EN_DBG (port);I'm not a fan of these temporary reg offset variables. Makes it hard to figure out later which register is being frobbed, especially when the variable name doesn't say what it actually is (like in this case). So I'd like to see this killed off.
How about something like below?
thanks,
Takashi
-- 8< --
From: Pierre-Louis Bossart <[email protected]>
Subject: [PATCH v2] drm/i915: add DisplayPort amp unmute for LPE audio mode
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38 prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 12 ++++++++++++ 2 files changed, 22 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +10 -0
@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)
drivers/gpu/drm/i915/intel_lpe_audio.c +12 -0
@@ -337,6 +337,7 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ; +u32 audio_enable;if (!HAS_LPE_AUDIO (dev_priv))return ;
@@ -346,6 +347,8 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv,spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + audio_enable =I915_READ (VLV_AUD_PORT_EN_DBG (port)); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );
@@ -357,11 +360,20 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)
Signature · 5 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Ville Syrjälä
Acked-byRe: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 108 lines · Takashi Iwai
Quoted 65 lines · Ville Syrjälä
Quoted 45 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.Signed-off-by Pierre-Louis Bossart <[email protected]>Signed-off-by Takashi Iwai <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 17 +++++++++++++++++ 2 files changed, 27 insertions(+)drivers/gpu/drm/i915/i915_reg.h +10
-0@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)drivers/gpu/drm/i915/intel_lpe_audio.c +0
-0@@ -337,15 +337,25 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ;drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, · line 349
Quoted 10 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +6
-0+u32 audio_enable; +i915_reg_t mmio;if (!HAS_LPE_AUDIO (dev_priv))return ; +if (port ==PORT_A ) { +DRM_ERROR ("PORT_A is not valid for HDMI/DP usages\n" ); +return ; + }Port A doesn't exists on these platforms at all. So this is just dead code.
Quoted 4 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +1
-0+ pdata =dev_get_platdata ( &(dev_priv->lpe_audio.platdev->dev));Quoted 8 lines
drivers/gpu/drm/i915/intel_lpe_audio.c void intel_lpe_audio_notify(struct drm_i915_private *dev_priv,
Quoted 3 lines
drivers/gpu/drm/i915/intel_lpe_audio.c +1
-0spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + mmio =VLV_AUD_PORT_EN_DBG (port);I'm not a fan of these temporary reg offset variables. Makes it hard to figure out later which register is being frobbed, especially when the variable name doesn't say what it actually is (like in this case). So I'd like to see this killed off.
How about something like below?
thanks,
Takashi
-- 8< --
From: Pierre-Louis Bossart <[email protected]>
Subject: [PATCH v2] drm/i915: add DisplayPort amp unmute for LPE audio modeEnable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.Signed-off-by Pierre-Louis Bossart <[email protected]>Signed-off-by Takashi Iwai <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 12 ++++++++++++ 2 files changed, 22 insertions(+)drivers/gpu/drm/i915/i915_reg.h +0
-0
drivers/gpu/drm/i915/i915_reg.h enum skl_disp_power_wells { · line 2067
Quoted 7 lines
drivers/gpu/drm/i915/i915_reg.h +4
-0@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34)
We generally like to prefix the raw register offsets with '_' to make it clear they're not to be used directly.
With that fixed the i915 patches are
Quoted 53 lines
drivers/gpu/drm/i915/i915_reg.h +6
-0+#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)drivers/gpu/drm/i915/intel_lpe_audio.c +12
-0@@ -337,6 +337,7 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ; +u32 audio_enable;if (!HAS_LPE_AUDIO (dev_priv))return ;@@ -346,6 +347,8 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv,spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + audio_enable =I915_READ (VLV_AUD_PORT_EN_DBG (port)); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );@@ -357,11 +360,20 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)Signature · 1 line
2.11.0
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Takashi Iwai
Acked-by Ville SyrjäläRe: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 11 lines · Ville Syrjälä
Review
Quoted 5 lines
(quoted diff) +4
-0+/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34)We generally like to prefix the raw register offsets with '_' to make it clear they're not to be used directly.
With that fixed the i915 patches are
Acked-by Ville Syrjälä <[email protected]>
Alright, below is the respinned one.
Thanks!
Takashi
-- 8< --
From: Pierre-Louis Bossart <[email protected]>
Subject: [PATCH v3] drm/i915: add DisplayPort amp unmute for LPE audio mode
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38 prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable. v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 12 ++++++++++++ 2 files changed, 22 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +10 -0
@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define _VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define _VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define _VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + _VLV_AUD_PORT_EN_B_DBG, \ + _VLV_AUD_PORT_EN_C_DBG, \ + _VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)
drivers/gpu/drm/i915/intel_lpe_audio.c +12 -0
@@ -337,6 +337,7 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ; +u32 audio_enable;if (!HAS_LPE_AUDIO (dev_priv))return ;
@@ -346,6 +347,8 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv,spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + audio_enable =I915_READ (VLV_AUD_PORT_EN_DBG (port)); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );
@@ -357,11 +360,20 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (VLV_AUD_PORT_EN_DBG (port), + audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)
Signature · 6 lines
2.11.0 _______________________________________________ Alsa-devel mailing list [email protected] http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Re: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
In reply to Takashi IwaiQuoted 9 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.
Sorry, this seems like a wrong result. It worked yesterday, but when I retested the latest code today, it didn't work any longer. Then, after setting the chicken bit, it starts working again.
But now I can't make it broken again. Turn off the monitor, turn off the machine, DPMS off, suspend/resume... All still works without chicken bit set.
Also, the chicken bit of the register 0x62f38 couldn't be read back. The register always returns zero when read.
So the chicken bit helps definitely something on a device here, but it's still mystery how it works.
I'll send an additional patch to re-add the audio chicken bit stuff.
thanks,
Takashi
Quoted 81 lines
Signed-off-by Pierre-Louis Bossart <[email protected]>Signed-off-by Takashi Iwai <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 10 ++++++++++ drivers/gpu/drm/i915/intel_lpe_audio.c | 17 +++++++++++++++++ 2 files changed, 27 insertions(+)drivers/gpu/drm/i915/i915_reg.h +10
-0@@ -2061,6 +2061,16 @@ enum skl_disp_power_wells {#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000)#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 +/* DisplayPort Audio w/ LPE */ +#define VLV_AUD_PORT_EN_B_DBG (VLV_DISPLAY_BASE + 0x62F20) +#define VLV_AUD_PORT_EN_C_DBG (VLV_DISPLAY_BASE + 0x62F30) +#define VLV_AUD_PORT_EN_D_DBG (VLV_DISPLAY_BASE + 0x62F34) +#define VLV_AUD_PORT_EN_DBG (port) _MMIO_PORT3((port) - PORT_B, \ + VLV_AUD_PORT_EN_B_DBG, \ + VLV_AUD_PORT_EN_C_DBG, \ + VLV_AUD_PORT_EN_D_DBG) +#define VLV_AMP_MUTE (1 << 1) +#define GEN6_BSD_RNCID _MMIO(0x12198)#define GEN7_FF_THREAD_MODE _MMIO(0x20a0)drivers/gpu/drm/i915/intel_lpe_audio.c +17
-0@@ -337,15 +337,25 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, {unsigned long irq_flags;struct intel_hdmi_lpe_audio_pdata *pdata =NULL ; +u32 audio_enable; +i915_reg_t mmio;if (!HAS_LPE_AUDIO (dev_priv))return ; +if (port ==PORT_A ) { +DRM_ERROR ("PORT_A is not valid for HDMI/DP usages\n" ); +return ; + } + pdata =dev_get_platdata ( &(dev_priv->lpe_audio.platdev->dev));spin_lock_irqsave (&pdata->lpe_audio_slock, irq_flags); + mmio =VLV_AUD_PORT_EN_DBG (port); + audio_enable =I915_READ (mmio); +if (eld !=NULL ) {memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES );@@ -357,11 +367,18 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, pdata->tmds_clock_speed = tmds_clk_speed;if (link_rate) pdata->link_rate = link_rate; + +/* Unmute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable & ~VLV_AMP_MUTE ); + }else {memset (pdata->eld.eld_data,0 ,HDMI_MAX_ELD_BYTES ); pdata->hdmi_connected = false; pdata->dp_output = false; + +/* Mute the amp for both DP and HDMI */ +I915_WRITE (mmio, audio_enable |VLV_AMP_MUTE ); }if (pdata->notify_audio_lpe)Signature · 1 line
2.11.0
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 16 lines · Takashi Iwai
Quoted 9 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.Sorry, this seems like a wrong result. It worked yesterday, but when I retested the latest code today, it didn't work any longer. Then, after setting the chicken bit, it starts working again.
Quoted 6 lines
But now I can't make it broken again. Turn off the monitor, turn off the machine, DPMS off, suspend/resume... All still works without chicken bit set.
Also, the chicken bit of the register
0x62f38couldn't be read back. The register always returns zero when read.
The docs do say it's write-only actually.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/7] drm/i915: add DisplayPort amp unmute for LPE audio mode
Quoted 18 lines · Ville Syrjälä
Quoted 16 lines · Takashi Iwai
Quoted 9 lines · Takashi Iwai
From: Pierre-Louis Bossart <[email protected]>
Enable unmute/mute amp notification. This doesn't seem to affect HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address
0x62F38prior to the mute/unmute but this register doesn't seem to do anything so this phase was removed.Sorry, this seems like a wrong result. It worked yesterday, but when I retested the latest code today, it didn't work any longer. Then, after setting the chicken bit, it starts working again.
Quoted 8 lines
Quoted 6 lines
But now I can't make it broken again. Turn off the monitor, turn off the machine, DPMS off, suspend/resume... All still works without chicken bit set.
Also, the chicken bit of the register
0x62f38couldn't be read back. The register always returns zero when read.The docs do say it's write-only actually.
OK, thanks for confirmation!
Takashi
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/7 drm/i915: Avoid MST pipe handling for LPE audio
In reply to Takashi IwaiThe pipe gets cleared to -1 for non-MST before the ELD audio notification due to the MST audio support. This makes sense for HD-audio that received the MST handling, but it's useless for LPE audio. Handle the MST pipe hack conditionally only for HD-audio.
--- drivers/gpu/drm/i915/intel_audio.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)
drivers/gpu/drm/i915/intel_audio.c +11 -10
@@ -624,13 +624,14 @@ void intel_audio_codec_enable(struct intel_encoder *intel_encoder, dev_priv->av_enc_map[pipe] = intel_encoder;mutex_unlock (&dev_priv->av_mutex); -/* audio drivers expect pipe = -1 to indicate Non-MST cases */ -if (intel_encoder->type !=INTEL_OUTPUT_DP_MST ) - pipe =-1 ; - -if (acomp && acomp->audio_ops && acomp->audio_ops->pin_eld_notify) +if (acomp && acomp->audio_ops && acomp->audio_ops->pin_eld_notify) { +/* audio drivers expect pipe = -1 to indicate Non-MST cases */ +if (intel_encoder->type !=INTEL_OUTPUT_DP_MST ) + pipe =-1 ; acomp->audio_ops->pin_eld_notify (acomp->audio_ops->audio_ptr, (int ) port, (int ) pipe); + } +switch (intel_encoder->type) {case INTEL_OUTPUT_HDMI : intel_lpe_audio_notify(dev_priv, connector->eld, port,
@@ -671,13 +672,13 @@ void intel_audio_codec_disable(struct intel_encoder *intel_encoder) dev_priv->av_enc_map[pipe] =NULL ;mutex_unlock (&dev_priv->av_mutex); -/* audio drivers expect pipe = -1 to indicate Non-MST cases */ -if (intel_encoder->type !=INTEL_OUTPUT_DP_MST ) - pipe =-1 ; - -if (acomp && acomp->audio_ops && acomp->audio_ops->pin_eld_notify) +if (acomp && acomp->audio_ops && acomp->audio_ops->pin_eld_notify) { +/* audio drivers expect pipe = -1 to indicate Non-MST cases */ +if (intel_encoder->type !=INTEL_OUTPUT_DP_MST ) + pipe =-1 ; acomp->audio_ops->pin_eld_notify (acomp->audio_ops->audio_ptr, (int ) port, (int ) pipe); + }intel_lpe_audio_notify (dev_priv,NULL , port,0 , false,0 ); }
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/7 drm/i915: Pass pipe to LPE audio notification
In reply to Takashi IwaiThe LPE audio configuration depends on the pipe, thus we need to pass the currently used pipe. It's now embedded in struct intel_hdmi_lpe_audio_eld as well as port id.
--- drivers/gpu/drm/i915/i915_drv.h | 2 +- drivers/gpu/drm/i915/intel_audio.c | 6 +++--- drivers/gpu/drm/i915/intel_lpe_audio.c | 3 ++- include/drm/intel_lpe_audio.h | 1 + 4 files changed, 7 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +1 -1
@@ -3401,7 +3401,7 @@ int intel_lpe_audio_init(struct drm_i915_private *dev_priv);void intel_lpe_audio_teardown (struct drm_i915_private *dev_priv);void intel_lpe_audio_irq_handler (struct drm_i915_private *dev_priv);void intel_lpe_audio_notify (struct drm_i915_private *dev_priv, -void *eld,int port,int tmds_clk_speed, +void *eld,int port,int pipe,int tmds_clk_speed,bool dp_output,int link_rate);/* intel_i2c.c */
drivers/gpu/drm/i915/intel_audio.c +3 -3
@@ -634,12 +634,12 @@ void intel_audio_codec_enable(struct intel_encoder *intel_encoder,switch (intel_encoder->type) {case INTEL_OUTPUT_HDMI : -intel_lpe_audio_notify (dev_priv, connector->eld, port, +intel_lpe_audio_notify (dev_priv, connector->eld, port, pipe, crtc_state->port_clock, false,0 );break ;case INTEL_OUTPUT_DP : -intel_lpe_audio_notify (dev_priv, connector->eld, port, +intel_lpe_audio_notify (dev_priv, connector->eld, port, pipe, adjusted_mode->crtc_clock, true, crtc_state->port_clock);break ;
@@ -680,7 +680,7 @@ void intel_audio_codec_disable(struct intel_encoder *intel_encoder) (int) port, (int) pipe); } -intel_lpe_audio_notify (dev_priv,NULL , port,0 , false,0 ); +intel_lpe_audio_notify (dev_priv,NULL , port, pipe,0 , false,0 ); }/**
drivers/gpu/drm/i915/intel_lpe_audio.c +2 -1
@@ -332,7 +332,7 @@ void intel_lpe_audio_teardown(struct drm_i915_private *dev_priv)* Notify lpe audio driver of eld change. */ void intel_lpe_audio_notify (struct drm_i915_private *dev_priv, -void *eld,int port,int tmds_clk_speed, +void *eld,int port,int pipe,int tmds_clk_speed,bool dp_output,int link_rate) {unsigned long irq_flags;
@@ -360,6 +360,7 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv,memcpy (pdata->eld.eld_data, eld,HDMI_MAX_ELD_BYTES ); pdata->eld.port_id = port; + pdata->eld.pipe_id = pipe; pdata->hdmi_connected = true; pdata->dp_output = dp_output;
include/drm/intel_lpe_audio.h +1 -0
@@ -31,6 +31,7 @@struct intel_hdmi_lpe_audio_eld {int port_id; +int pipe_id;unsigned char eld_data[HDMI_MAX_ELD_BYTES ]; };
Signature · 1 line
2.11.0
PATCH 5/7 ALSA: x86: intel_hdmi: add definitions and logic for DP audio
In reply to Takashi IwaiFrom: Pierre-Louis Bossart <[email protected]>
Imported from legacy patches
Note: the new code doesn't assume a modified ELD but an explicit notification that DP is present. It appears that the i915 code does change the ELD so we could use the ELD-based tests to check for DP audio
--- sound/x86/intel_hdmi_audio.c | 173 +++++++++++++++++++++++++++++++++------ sound/x86/intel_hdmi_audio.h | 8 +- sound/x86/intel_hdmi_lpe_audio.c | 36 +++++++- sound/x86/intel_hdmi_lpe_audio.h | 29 +++++++ 4 files changed, 216 insertions(+), 30 deletions(-)
sound/x86/intel_hdmi_audio.c +147 -26
@@ -396,6 +396,7 @@ static int snd_intelhad_prog_audio_ctrl_v2(struct snd_pcm_substream *substream,else cfg_val.cfg_regx_v2.layout =LAYOUT1 ; + cfg_val.cfg_regx_v2.val_bit =1 ;had_write_register (AUD_CONFIG , cfg_val.cfg_regval);return 0 ; }
@@ -447,6 +448,7 @@ static int snd_intelhad_prog_audio_ctrl_v1(struct snd_pcm_substream *substream, } + cfg_val.cfg_regx.val_bit =1 ;had_write_register (AUD_CONFIG , cfg_val.cfg_regval);return 0 ; }
@@ -548,6 +550,7 @@ void had_build_channel_allocation_map(struct snd_intelhad *intelhaddata) }had_get_caps (HAD_GET_ELD , &intelhaddata->eeld); +had_get_caps (HAD_GET_DP_OUTPUT , &intelhaddata->dp_output);pr_debug ("eeld.speaker_allocation_block = %x\n" , intelhaddata->eeld.speaker_allocation_block);
@@ -685,7 +688,7 @@ static void snd_intelhad_prog_dip_v1(struct snd_pcm_substream *substream,/*Calculte the byte wide checksum for all valid DIP words*/ for (i =0 ; i <BYTES_PER_WORD ; i++) - checksum += (INFO_FRAME_WORD1 >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; + checksum += (HDMI_INFO_FRAME_WORD1 >> i*BITS_PER_BYTE ) &MASK_BYTE0 ;for (i =0 ; i <BYTES_PER_WORD ; i++) checksum += (frame2.fr2_val >> i*BITS_PER_BYTE ) &MASK_BYTE0 ;for (i =0 ; i <BYTES_PER_WORD ; i++)
@@ -693,7 +696,7 @@ static void snd_intelhad_prog_dip_v1(struct snd_pcm_substream *substream, frame2.fr2_regx.chksum = -(checksum); -had_write_register (AUD_HDMIW_INFOFR ,INFO_FRAME_WORD1 ); +had_write_register (AUD_HDMIW_INFOFR ,HDMI_INFO_FRAME_WORD1 );had_write_register (AUD_HDMIW_INFOFR , frame2.fr2_val);had_write_register (AUD_HDMIW_INFOFR , frame3.fr3_val);
@@ -722,28 +725,35 @@ static void snd_intelhad_prog_dip_v2(struct snd_pcm_substream *substream,union aud_info_frame2 frame2 = {.fr2_val =0 };union aud_info_frame3 frame3 = {.fr3_val =0 };u8 checksum =0 ; +u32 info_frame;int channels; channels = substream->runtime->channels;had_write_register (AUD_CNTL_ST , ctrl_state.ctrl_val); - frame2.fr2_regx.chnl_cnt = substream->runtime->channels -1 ; +if (intelhaddata->dp_output) { + info_frame =DP_INFO_FRAME_WORD1 ; + frame2.fr2_val =1 ; + }else { + info_frame =HDMI_INFO_FRAME_WORD1 ; + frame2.fr2_regx.chnl_cnt = substream->runtime->channels -1 ; - frame3.fr3_regx.chnl_alloc =snd_intelhad_channel_allocation ( - intelhaddata, channels); + frame3.fr3_regx.chnl_alloc =snd_intelhad_channel_allocation ( + intelhaddata, channels); -/*Calculte the byte wide checksum for all valid DIP words*/ -for (i =0 ; i <BYTES_PER_WORD ; i++) - checksum += (INFO_FRAME_WORD1 >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; -for (i =0 ; i <BYTES_PER_WORD ; i++) - checksum += (frame2.fr2_val >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; -for (i =0 ; i <BYTES_PER_WORD ; i++) - checksum += (frame3.fr3_val >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; +/*Calculte the byte wide checksum for all valid DIP words*/ +for (i =0 ; i <BYTES_PER_WORD ; i++) + checksum += (info_frame >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; +for (i =0 ; i <BYTES_PER_WORD ; i++) + checksum += (frame2.fr2_val >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; +for (i =0 ; i <BYTES_PER_WORD ; i++) + checksum += (frame3.fr3_val >> i*BITS_PER_BYTE ) &MASK_BYTE0 ; - frame2.fr2_regx.chksum = -(checksum); + frame2.fr2_regx.chksum = -(checksum); + } -had_write_register (AUD_HDMIW_INFOFR_v2,INFO_FRAME_WORD1 ); +had_write_register (AUD_HDMIW_INFOFR_v2, info_frame);had_write_register (AUD_HDMIW_INFOFR_v2, frame2.fr2_val);had_write_register (AUD_HDMIW_INFOFR_v2, frame3.fr3_val);
@@ -839,6 +849,85 @@ int snd_intelhad_read_len(struct snd_intelhad *intelhaddata)return retval; } +static int had_calculate_maud_value (u32 aud_samp_freq,u32 link_rate) +{ +u32 maud_val; + +/* Select maud according to DP 1.2 spec*/ +if (link_rate ==DP_2_7_GHZ ) { +switch (aud_samp_freq) { +case AUD_SAMPLE_RATE_32 : + maud_val =AUD_SAMPLE_RATE_32_DP_2_7_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_44_1 : + maud_val =AUD_SAMPLE_RATE_44_1_DP_2_7_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_48 : + maud_val =AUD_SAMPLE_RATE_48_DP_2_7_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_88_2 : + maud_val =AUD_SAMPLE_RATE_88_2_DP_2_7_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_96 : + maud_val =AUD_SAMPLE_RATE_96_DP_2_7_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_176_4 : + maud_val =AUD_SAMPLE_RATE_176_4_DP_2_7_MAUD_VAL ; +break ; + +case HAD_MAX_RATE : + maud_val =HAD_MAX_RATE_DP_2_7_MAUD_VAL ; +break ; + +default : + maud_val = -EINVAL ; +break ; + } + }else if (link_rate ==DP_1_62_GHZ ) { +switch (aud_samp_freq) { +case AUD_SAMPLE_RATE_32 : + maud_val =AUD_SAMPLE_RATE_32_DP_1_62_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_44_1 : + maud_val =AUD_SAMPLE_RATE_44_1_DP_1_62_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_48 : + maud_val =AUD_SAMPLE_RATE_48_DP_1_62_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_88_2 : + maud_val =AUD_SAMPLE_RATE_88_2_DP_1_62_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_96 : + maud_val =AUD_SAMPLE_RATE_96_DP_1_62_MAUD_VAL ; +break ; + +case AUD_SAMPLE_RATE_176_4 : + maud_val =AUD_SAMPLE_RATE_176_4_DP_1_62_MAUD_VAL ; +break ; + +case HAD_MAX_RATE : + maud_val =HAD_MAX_RATE_DP_1_62_MAUD_VAL ; +break ; + +default : + maud_val = -EINVAL ; +break ; + } + }else + maud_val = -EINVAL ; + +return maud_val; +} +/** * snd_intelhad_prog_cts_v1 - Program HDMI audio CTS value *
@@ -849,8 +938,9 @@ int snd_intelhad_read_len(struct snd_intelhad *intelhaddata)* * Program CTS register based on the audio and display sampling frequency */ -static void snd_intelhad_prog_cts_v1 (u32 aud_samp_freq,u32 tmds,u32 n_param, -struct snd_intelhad *intelhaddata) +static void snd_intelhad_prog_cts_v1 (u32 aud_samp_freq,u32 tmds, +u32 link_rate,u32 n_param, +struct snd_intelhad *intelhaddata) {u32 cts_val;u64 dividend, divisor;
@@ -874,18 +964,24 @@ static void snd_intelhad_prog_cts_v1(u32 aud_samp_freq, u32 tmds, u32 n_param,* * Program CTS register based on the audio and display sampling frequency */ -static void snd_intelhad_prog_cts_v2 (u32 aud_samp_freq,u32 tmds,u32 n_param, -struct snd_intelhad *intelhaddata) +static void snd_intelhad_prog_cts_v2 (u32 aud_samp_freq,u32 tmds, +u32 link_rate,u32 n_param, +struct snd_intelhad *intelhaddata) {u32 cts_val;u64 dividend, divisor; -/* Calculate CTS according to HDMI 1.3a spec*/ - dividend = (u64 )tmds * n_param*1000 ; - divisor =128 * aud_samp_freq; - cts_val =div64_u64 (dividend, divisor); +if (intelhaddata->dp_output) { +/* Substitute cts_val with Maud according to DP 1.2 spec*/ + cts_val =had_calculate_maud_value (aud_samp_freq, link_rate); + }else { +/* Calculate CTS according to HDMI 1.3a spec*/ + dividend = (u64 )tmds * n_param*1000 ; + divisor =128 * aud_samp_freq; + cts_val =div64_u64 (dividend, divisor); + }pr_debug ("TMDS value=%d, N value=%d, CTS Value=%d\n" , - tmds, n_param, cts_val); + tmds, n_param, cts_val);had_write_register (AUD_HDMI_CTS , (BIT (24 ) | cts_val)); }
@@ -970,7 +1066,18 @@ static int snd_intelhad_prog_n_v2(u32 aud_samp_freq, u32 *n_param, {s32 n_val; - n_val =had_calculate_n_value (aud_samp_freq); +if (intelhaddata->dp_output) { +/* +* According to DP specs, Maud and Naud values hold +* a relationship, which is stated as: +* Maud/Naud = 512 * fs / f_LS_Clk +* where, fs is the sampling frequency of the audio stream +* and Naud is 32768 for Async clock. +*/ + + n_val =DP_NAUD_VAL ; + }else + n_val =had_calculate_n_value (aud_samp_freq);if (n_val <0 )return n_val;
@@ -1343,6 +1450,7 @@ static int snd_intelhad_pcm_prepare(struct snd_pcm_substream *substream) {int retval;u32 disp_samp_freq, n_param; +u32 link_rate =0 ;struct snd_intelhad *intelhaddata;struct snd_pcm_runtime *runtime;struct had_pvt_data *had_stream;
@@ -1387,6 +1495,7 @@ static int snd_intelhad_pcm_prepare(struct snd_pcm_substream *substream) }had_get_caps (HAD_GET_ELD , &intelhaddata->eeld); +had_get_caps (HAD_GET_DP_OUTPUT , &intelhaddata->dp_output); retval = intelhaddata->ops->prog_n (substream->runtime->rate, &n_param, intelhaddata);
@@ -1394,8 +1503,14 @@ static int snd_intelhad_pcm_prepare(struct snd_pcm_substream *substream)pr_err ("programming N value failed %#x\n" , retval); goto prep_end; } + +if (intelhaddata->dp_output) +had_get_caps (HAD_GET_LINK_RATE , &link_rate); + + intelhaddata->ops->prog_cts (substream->runtime->rate, - disp_samp_freq, n_param, intelhaddata); + disp_samp_freq, link_rate, + n_param, intelhaddata); intelhaddata->ops->prog_dip (substream, intelhaddata);
@@ -1503,6 +1618,7 @@ int hdmi_audio_mode_change(struct snd_pcm_substream *substream) {int retval =0 ;u32 disp_samp_freq, n_param; +u32 link_rate =0 ;struct snd_intelhad *intelhaddata; intelhaddata =snd_pcm_substream_chip (substream);
@@ -1523,8 +1639,13 @@ int hdmi_audio_mode_change(struct snd_pcm_substream *substream)pr_err ("programming N value failed %#x\n" , retval); goto out; } + +if (intelhaddata->dp_output) +had_get_caps (HAD_GET_LINK_RATE , &link_rate); + intelhaddata->ops->prog_cts (substream->runtime->rate, - disp_samp_freq, n_param, intelhaddata); + disp_samp_freq, link_rate, + n_param, intelhaddata);/* Enable Audio */ intelhaddata->ops->enable_audio (substream,1 );
sound/x86/intel_hdmi_audio.h +5 -3
@@ -44,7 +44,8 @@#define MAX_CAP_STREAMS 0#define HDMI_AUDIO_DRIVER "hdmi-audio" -#define INFO_FRAME_WORD1 0x000a0184 +#define HDMI_INFO_FRAME_WORD1 0x000a0184 +#define DP_INFO_FRAME_WORD1 0x00441b84#define FIFO_THRESHOLD 0xFE#define DMA_FIFO_THRESHOLD 0x7#define BYTES_PER_WORD 0x4
@@ -134,6 +135,7 @@ struct snd_intelhad {struct ring_buf_info buf_info[HAD_NUM_OF_RING_BUFS ];struct pcm_stream_info stream_info;union otm_hdmi_eld_t eeld; +bool dp_output;enum intel_had_aud_buf_type curr_buf;int valid_buf_cnt;unsigned int aes_bits;
@@ -156,8 +158,8 @@ struct had_ops {void (*reset_audio)(u8 reset);int (*prog_n)(u32 aud_samp_freq,u32 *n_param,struct snd_intelhad *intelhaddata); -void (*prog_cts)(u32 aud_samp_freq,u32 tmds,u32 n_param, -struct snd_intelhad *intelhaddata); +void (*prog_cts)(u32 aud_samp_freq,u32 tmds,u32 link_rate, +u32 n_param,struct snd_intelhad *intelhaddata);int (*audio_ctrl)(struct snd_pcm_substream *substream,struct snd_intelhad *intelhaddata); void (*prog_dip)(struct snd_pcm_substream *substream,
sound/x86/intel_hdmi_lpe_audio.c +35 -1
@@ -48,6 +48,8 @@ struct hdmi_lpe_audio_ctx {struct snd_intel_had_interface *had_interface;void *had_pvt_data;int tmds_clock_speed; +bool dp_output; +int link_rate;unsigned int had_config_offset;int hdmi_audio_interrupt_mask;struct work_struct hdmi_audio_wq;
@@ -187,6 +189,15 @@ static int hdmi_audio_write(u32 reg, u32 val)dev_dbg (&hlpe_pdev->dev,"%s: reg[0x%x] = 0x%x\n" , __func__, reg, val); +if (ctx->dp_output) { +if ((reg ==AUDIO_HDMI_CONFIG_A ) || + (reg ==AUDIO_HDMI_CONFIG_B ) || + (reg ==AUDIO_HDMI_CONFIG_C )) { +if (val &AUD_CONFIG_VALID_BIT ) + val = val |AUD_CONFIG_DP_MODE | +AUD_CONFIG_BLOCK_BIT ; + } + }iowrite32 (val, (ctx->mmio_start+reg));return 0 ;
@@ -220,6 +231,16 @@ static int hdmi_audio_rmw(u32 reg, u32 val, u32 mask) val_tmp = (val & mask) | ((ioread32 (ctx->mmio_start + reg)) & ~mask); +if (ctx->dp_output) { +if ((reg ==AUDIO_HDMI_CONFIG_A ) || + (reg ==AUDIO_HDMI_CONFIG_B ) || + (reg ==AUDIO_HDMI_CONFIG_C )) { +if (val_tmp &AUD_CONFIG_VALID_BIT ) + val_tmp = val_tmp |AUD_CONFIG_DP_MODE | +AUD_CONFIG_BLOCK_BIT ; + } + } +iowrite32 (val_tmp, (ctx->mmio_start+reg));dev_dbg (&hlpe_pdev->dev,"%s: reg[0x%x] = 0x%x\n" , __func__, reg, val_tmp);
@@ -249,7 +270,18 @@ static int hdmi_audio_get_caps(enum had_caps_list get_element,/* ToDo: Verify if sampling freq logic is correct */ *(u32 *)capabilities = ctx->tmds_clock_speed;dev_dbg (&hlpe_pdev->dev,"%s: tmds_clock_speed = 0x%x\n" , - __func__, ctx->tmds_clock_speed); + __func__, ctx->tmds_clock_speed); +break ; +case HAD_GET_LINK_RATE : +/* ToDo: Verify if sampling freq logic is correct */ + *(u32 *)capabilities = ctx->link_rate; +dev_dbg (&hlpe_pdev->dev,"%s: link rate = 0x%x\n" , + __func__, ctx->link_rate); +break ; +case HAD_GET_DP_OUTPUT : + *(u32 *)capabilities = ctx->dp_output; +dev_dbg (&hlpe_pdev->dev,"%s: dp_output = %d\n" , + __func__, ctx->dp_output);break ;default :break ;
@@ -442,6 +474,8 @@ static void notify_audio_lpe(void *audio_ptr)if (pdata->tmds_clock_speed) { ctx->tmds_clock_speed = pdata->tmds_clock_speed; + ctx->dp_output = pdata->dp_output; + ctx->link_rate = pdata->link_rate;mid_hdmi_audio_signal_event (HAD_EVENT_MODE_CHANGING ); } }else
sound/x86/intel_hdmi_lpe_audio.h +29 -0
@@ -31,6 +31,10 @@#include <sound/control.h> #include <sound/pcm.h> +#define AUD_CONFIG_VALID_BIT (1<<9) +#define AUD_CONFIG_DP_MODE (1<<15) +#define AUD_CONFIG_BLOCK_BIT (1<<7) +#define HMDI_LPE_AUDIO_DRIVER_NAME "intel-hdmi-lpe-audio"#define HAD_MAX_DEVICES 1#define HAD_MIN_CHANNEL 2
@@ -68,6 +72,29 @@#define HAD_MAX_DIP_WORDS 16#define INTEL_HAD "IntelHdmiLpeAudio" +/* DP Link Rates */ +#define DP_2_7_GHZ 270000 +#define DP_1_62_GHZ 162000 + +/* Maud Values */ +#define AUD_SAMPLE_RATE_32_DP_2_7_MAUD_VAL 1988 +#define AUD_SAMPLE_RATE_44_1_DP_2_7_MAUD_VAL 2740 +#define AUD_SAMPLE_RATE_48_DP_2_7_MAUD_VAL 2982 +#define AUD_SAMPLE_RATE_88_2_DP_2_7_MAUD_VAL 5480 +#define AUD_SAMPLE_RATE_96_DP_2_7_MAUD_VAL 5965 +#define AUD_SAMPLE_RATE_176_4_DP_2_7_MAUD_VAL 10961 +#define HAD_MAX_RATE_DP_2_7_MAUD_VAL 11930 +#define AUD_SAMPLE_RATE_32_DP_1_62_MAUD_VAL 3314 +#define AUD_SAMPLE_RATE_44_1_DP_1_62_MAUD_VAL 4567 +#define AUD_SAMPLE_RATE_48_DP_1_62_MAUD_VAL 4971 +#define AUD_SAMPLE_RATE_88_2_DP_1_62_MAUD_VAL 9134 +#define AUD_SAMPLE_RATE_96_DP_1_62_MAUD_VAL 9942 +#define AUD_SAMPLE_RATE_176_4_DP_1_62_MAUD_VAL 18268 +#define HAD_MAX_RATE_DP_1_62_MAUD_VAL 19884 + +/* Naud Value */ +#define DP_NAUD_VAL 32768 +/* _AUD_CONFIG register MASK */ #define AUD_CONFIG_MASK_UNDERRUN 0xC0000000#define AUD_CONFIG_MASK_SRDBG 0x00000002
@@ -618,6 +645,8 @@ enum hdmi_connector_status {enum had_caps_list {HAD_GET_ELD =1 ,HAD_GET_DISPLAY_RATE , +HAD_GET_DP_OUTPUT , +HAD_GET_LINK_RATE ,HAD_SET_ENABLE_AUDIO ,HAD_SET_DISABLE_AUDIO ,HAD_SET_ENABLE_AUDIO_INT ,
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 6/7 ALSA: x86: Use config base depending on the pipe
In reply to Takashi IwaiFrom: Pierre-Louis Bossart <[email protected]>
Now the pipe that is being used is passed over i915 notification, we can re-setup the relevant register offset depending on pipe assignments during hotplug.
This allows playback on single port machines such Zotac Pi330 or dual-port machines such as Dell Wyse 3040 box
--- sound/x86/intel_hdmi_lpe_audio.c | 26 +++++++++++++++++++++----- 1 file changed, 21 insertions(+), 5 deletions(-)
sound/x86/intel_hdmi_lpe_audio.c +21 -5
@@ -463,6 +463,22 @@ static void notify_audio_lpe(void *audio_ptr) }else if (eld !=NULL ) { +switch (eld->pipe_id) { +case 0 : + ctx->had_config_offset =AUDIO_HDMI_CONFIG_A ; +break ; +case 1 : + ctx->had_config_offset =AUDIO_HDMI_CONFIG_B ; +break ; +case 2 : + ctx->had_config_offset =AUDIO_HDMI_CONFIG_C ; +break ; +default : +dev_dbg (&hlpe_pdev->dev,"Invalid pipe %d\n" , + eld->pipe_id); +break ; + } +hdmi_set_eld (eld->eld_data);mid_hdmi_audio_signal_event (HAD_EVENT_HOT_PLUG );
@@ -560,15 +576,15 @@ static int hdmi_lpe_audio_probe(struct platform_device *pdev) ctx->mmio_start = mmio_start; ctx->tmds_clock_speed =DIS_SAMPLE_RATE_148_5 ; -if (pci_dev_present (cherryview_ids)) { +if (pci_dev_present (cherryview_ids))dev_dbg (&hlpe_pdev->dev,"%s: Cherrytrail LPE - Detected\n" , __func__); - ctx->had_config_offset =AUDIO_HDMI_CONFIG_C ; - }else { +else dev_dbg (&hlpe_pdev->dev,"%s: Baytrail LPE - Assume\n" , __func__); - ctx->had_config_offset =AUDIO_HDMI_CONFIG_A ; - } + +/* assume pipe A as default */ + ctx->had_config_offset =AUDIO_HDMI_CONFIG_A ; pdata = pdev->dev.platform_data;
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 7/7 drm/i915: Pass platform device to LPE audio notifier
In reply to Takashi IwaiThis allows the LPE HDMI driver to clean up its global variable reference.
Also drop to pass the eld pointer because the connection status and the ELD bytes can be retrieved from the attached pdata.
--- drivers/gpu/drm/i915/intel_lpe_audio.c | 3 +-- include/drm/intel_lpe_audio.h | 4 +++- sound/x86/intel_hdmi_lpe_audio.c | 23 +++++++++++------------ 3 files changed, 15 insertions(+), 15 deletions(-)
drivers/gpu/drm/i915/intel_lpe_audio.c +1 -2
@@ -383,8 +383,7 @@ void intel_lpe_audio_notify(struct drm_i915_private *dev_priv, }if (pdata->notify_audio_lpe) - pdata->notify_audio_lpe ( - (eld !=NULL ) ? &pdata->eld :NULL ); + pdata->notify_audio_lpe (dev_priv->lpe_audio.platdev);else pdata->notify_pending = true;
include/drm/intel_lpe_audio.h +3 -1
@@ -27,6 +27,8 @@#include <linux/types.h> #include <linux/spinlock_types.h> +struct platform_device ; +#define HDMI_MAX_ELD_BYTES 128struct intel_hdmi_lpe_audio_eld {
@@ -42,7 +44,7 @@ struct intel_hdmi_lpe_audio_pdata {bool dp_output;int link_rate;struct intel_hdmi_lpe_audio_eld eld; -void (*notify_audio_lpe)(void *audio_ptr); +void (*notify_audio_lpe)(struct platform_device *pdev);spinlock_t lpe_audio_slock; };
sound/x86/intel_hdmi_lpe_audio.c +11 -12
@@ -439,15 +439,14 @@ static irqreturn_t display_pipe_interrupt_handler(int irq, void *dev_id)return IRQ_HANDLED ; } -static void notify_audio_lpe (void *audio_ptr) +static void notify_audio_lpe (struct platform_device *pdev) { -struct hdmi_lpe_audio_ctx *ctx =get_hdmi_context (); -struct intel_hdmi_lpe_audio_pdata *pdata = hlpe_pdev->dev.platform_data; -struct intel_hdmi_lpe_audio_eld *eld = audio_ptr; +struct hdmi_lpe_audio_ctx *ctx =platform_get_drvdata (pdev); +struct intel_hdmi_lpe_audio_pdata *pdata = pdev->dev.platform_data;if (pdata->hdmi_connected != true) { -dev_dbg (&hlpe_pdev->dev,"%s: Event: HAD_NOTIFY_HOT_UNPLUG\n" , +dev_dbg (&pdev->dev,"%s: Event: HAD_NOTIFY_HOT_UNPLUG\n" , __func__);if (hlpe_state == hdmi_connector_status_connected) {
@@ -458,10 +457,11 @@ static void notify_audio_lpe(void *audio_ptr)mid_hdmi_audio_signal_event (HAD_EVENT_HOT_UNPLUG ); }else -dev_dbg (&hlpe_pdev->dev,"%s: Already Unplugged!\n" , +dev_dbg (&pdev->dev,"%s: Already Unplugged!\n" , __func__); - }else if (eld !=NULL ) { + }else { +struct intel_hdmi_lpe_audio_eld *eld = &pdata->eld;switch (eld->pipe_id) {case 0 :
@@ -474,7 +474,7 @@ static void notify_audio_lpe(void *audio_ptr) ctx->had_config_offset =AUDIO_HDMI_CONFIG_C ;break ;default : -dev_dbg (&hlpe_pdev->dev,"Invalid pipe %d\n" , +dev_dbg (&pdev->dev,"Invalid pipe %d\n" , eld->pipe_id);break ; }
@@ -485,7 +485,7 @@ static void notify_audio_lpe(void *audio_ptr) hlpe_state = hdmi_connector_status_connected; -dev_dbg (&hlpe_pdev->dev,"%s: HAD_NOTIFY_ELD : port = %d, tmds = %d\n" , +dev_dbg (&pdev->dev,"%s: HAD_NOTIFY_ELD : port = %d, tmds = %d\n" , __func__, eld->port_id, pdata->tmds_clock_speed);if (pdata->tmds_clock_speed) {
@@ -494,8 +494,7 @@ static void notify_audio_lpe(void *audio_ptr) ctx->link_rate = pdata->link_rate;mid_hdmi_audio_signal_event (HAD_EVENT_MODE_CHANGING ); } - }else -dev_dbg (&hlpe_pdev->dev,"%s: Event: NULL EDID!!\n" , __func__); + } }/**
@@ -606,7 +605,7 @@ static int hdmi_lpe_audio_probe(struct platform_device *pdev)if (pdata->notify_pending) {dev_dbg (&hlpe_pdev->dev,"%s: handle pending notification\n" , __func__); -notify_audio_lpe (&pdata->eld); +notify_audio_lpe (pdev); pdata->notify_pending = false; }spin_unlock_irqrestore (&pdata->lpe_audio_slock, flag_irq);
Signature · 6 lines
2.11.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for DisplayPort audio support on Cherrytrail
In reply to Takashi Iwai== Series Details ==
== Series Details ==
Series: DisplayPort audio support on Cherrytrail
URL : https://patchwork.freedesktop.org/series/18864/
State : success
== Summary ==
Series 18864v1 DisplayPort audio support on Cherrytrail
https://patchwork.freedesktop.org/api/1.0/series/18864/revisions/1/mbox/
fi-bdw-5557u total:247 pass:233 dwarn:0 dfail:0 fail:0 skip:14 fi-bsw-n3050 total:247 pass:208 dwarn:0 dfail:0 fail:0 skip:39 fi-bxt-j4205 total:247 pass:225 dwarn:0 dfail:0 fail:0 skip:22 fi-bxt-t5700 total:78 pass:65 dwarn:0 dfail:0 fail:0 skip:12 fi-byt-j1900 total:247 pass:220 dwarn:0 dfail:0 fail:0 skip:27 fi-byt-n2820 total:247 pass:216 dwarn:0 dfail:0 fail:0 skip:31 fi-hsw-4770 total:247 pass:228 dwarn:0 dfail:0 fail:0 skip:19 fi-hsw-4770r total:247 pass:228 dwarn:0 dfail:0 fail:0 skip:19 fi-ivb-3520m total:247 pass:226 dwarn:0 dfail:0 fail:0 skip:21 fi-ivb-3770 total:247 pass:226 dwarn:0 dfail:0 fail:0 skip:21 fi-kbl-7500u total:247 pass:224 dwarn:0 dfail:0 fail:2 skip:21 fi-skl-6260u total:247 pass:234 dwarn:0 dfail:0 fail:0 skip:13 fi-skl-6700hq total:247 pass:227 dwarn:0 dfail:0 fail:0 skip:20 fi-skl-6700k total:247 pass:222 dwarn:4 dfail:0 fail:0 skip:21 fi-skl-6770hq total:247 pass:234 dwarn:0 dfail:0 fail:0 skip:13 fi-snb-2520m total:247 pass:216 dwarn:0 dfail:0 fail:0 skip:31 fi-snb-2600 total:247 pass:215 dwarn:0 dfail:0 fail:0 skip:32
83f390eaec64a1b0566f5f747d20741c077fcff5 drm-tip: 2017y-01m-31d-20h-19m-59s UTC integration manifest 15954fb drm/i915: Pass platform device to LPE audio notifier
1358641 ALSA: x86: Use config base depending on the pipe
0545a59 ALSA: x86: intel_hdmi: add definitions and logic for DP audio
14efa05 drm/i915: Pass pipe to LPE audio notification
32b5514 drm/i915: Avoid MST pipe handling for LPE audio
82dd01f drm/i915: add DisplayPort amp unmute for LPE audio mode
9bf23c4 drm/i915: add DP support in LPE audio mode
== Logs ==
For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_3656/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 26 lines · Takashi Iwai
Hi,
the following patches enable DisplayPort Audio on Cherrytrail machines when applied on top of my topic/intel-lpe-audio branch. Tests of DP audio were run on Dell Wyse 3040. The regression test were performed on Baytrail (Compute Stick) and Cherrytrail (Zotac PI330) in HDMI mode. On Cherrytrail there were no issues changing between HDMI and DP connectors dynamically.
Could you i915 people review and give ACK if they are OK? The changes in drm/i915 side are fairly trivial, so I'd like to take them through sound git tree once after I receive your ACKs.
Changes since RFC:
- reordered and squashed patches
- clean-up of register definitions and offsets (based on feedback from Jani/Ville)
- unmute amp for both HDMI and DP unconditionally
- mute amp on invalid ELD (unplug)
- remove test for chicken bit which seems to have no effect in hardware
- cosmetic edits to make checkpatch happy
- change i915 notification argument to pass the plataform device instead
Quoted 2 lines
Most of hard work in this patchset has been done by Pierre, so all credits go to him.
Please build the htmldocs and fix the new fallout these patches create:
$ make DOCBOOKS="" htmldocs
0day should be reporting these (if it scans your mailing list), but there's been a hiccup recently.
Good docs matter and all that ...
Thanks, Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch
Quoted 30 lines · Daniel Vetter
Quoted 26 lines · Takashi Iwai
Hi,
the following patches enable DisplayPort Audio on Cherrytrail machines when applied on top of my topic/intel-lpe-audio branch. Tests of DP audio were run on Dell Wyse 3040. The regression test were performed on Baytrail (Compute Stick) and Cherrytrail (Zotac PI330) in HDMI mode. On Cherrytrail there were no issues changing between HDMI and DP connectors dynamically.
Could you i915 people review and give ACK if they are OK? The changes in drm/i915 side are fairly trivial, so I'd like to take them through sound git tree once after I receive your ACKs.
Changes since RFC:
- reordered and squashed patches
- clean-up of register definitions and offsets (based on feedback from Jani/Ville)
- unmute amp for both HDMI and DP unconditionally
- mute amp on invalid ELD (unplug)
- remove test for chicken bit which seems to have no effect in hardware
- cosmetic edits to make checkpatch happy
- change i915 notification argument to pass the plataform device insteadQuoted 2 lines
Most of hard work in this patchset has been done by Pierre, so all credits go to him.
Quoted 8 lines
Please build the htmldocs and fix the new fallout these patches create:
$ make DOCBOOKS="" htmldocs0day should be reporting these (if it scans your mailing list), but there's been a hiccup recently.
Good docs matter and all that ...
Apparently this is still not fixed, I applied a fixup patch now from someone else. Tsk.
-Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 36 lines · Daniel Vetter
Quoted 34 lines · Daniel Vetter
Quoted 26 lines · Takashi Iwai
Hi,
the following patches enable DisplayPort Audio on Cherrytrail machines when applied on top of my topic/intel-lpe-audio branch. Tests of DP audio were run on Dell Wyse 3040. The regression test were performed on Baytrail (Compute Stick) and Cherrytrail (Zotac PI330) in HDMI mode. On Cherrytrail there were no issues changing between HDMI and DP connectors dynamically.
Could you i915 people review and give ACK if they are OK? The changes in drm/i915 side are fairly trivial, so I'd like to take them through sound git tree once after I receive your ACKs.
Changes since RFC:
- reordered and squashed patches
- clean-up of register definitions and offsets (based on feedback from Jani/Ville)
- unmute amp for both HDMI and DP unconditionally
- mute amp on invalid ELD (unplug)
- remove test for chicken bit which seems to have no effect in hardware
- cosmetic edits to make checkpatch happy
- change i915 notification argument to pass the plataform device insteadQuoted 2 lines
Most of hard work in this patchset has been done by Pierre, so all credits go to him.
Please build the htmldocs and fix the new fallout these patches create:
$ make DOCBOOKS="" htmldocs
Quoted 7 lines
Quoted 4 lines
0day should be reporting these (if it scans your mailing list), but there's been a hiccup recently.
Good docs matter and all that ...
Apparently this is still not fixed, I applied a fixup patch now from someone else. Tsk.
Ah, sorry, this felt into crack during my vacation. Good that it was already fixed. Thanks.
Takashi
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx