Skip to contentSkip to conversation

aspeed: pinctrl: Allow disabling Port D and Port E loopback mode

PATCH Superseded Rick Altherr 2 participants 2 messages Feb 15, 2017 – Feb 23, 2017

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 aspeed: pinctrl: Allow disabling Port D and Port E loopback mode

Port D and port E GPIO loopback modes are commonly enabled via hardware straps for use with front-panel buttons. When the BMC is powered off or fails to boot, the front-panel buttons are directly connected to the host chipset via the loopback to allow direct power-on and reset control. Once the BMC has booted, the loopback mode must be disabled for the BMC to take over control of host power-on and reset.

Disabling these loopback modes requires writing to the hardware strap register which violates the current design of assuming the system designer chose the strap settings for a specific reason and they should be treated as read-only. Only the two bits of the strap register related to these loopback modes are allowed to be written and comments have been added to explain why.

---
 drivers/pinctrl/aspeed/pinctrl-aspeed.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
drivers/pinctrl/aspeed/pinctrl-aspeed.c +12 -2
index 76f62bd45f02..5b49952e5fad 100644
@@ -198,9 +198,19 @@ static int aspeed_sig_expr_set(const struct aspeed_sig_expr *expr,
 		 * them. This may mean that certain functions cannot be
 		 * deconfigured and is the reason we re-evaluate after writing
 		 * all descriptor bits.
+		 *
+		 * Port D and port E GPIO loopback modes are the only exception
+		 * as those are commonly used with front-panel buttons to allow
+		 * normal operation of the host when the BMC is powered off or
+		 * fails to boot. Once the BMC has booted, the loopback mode
+		 * must be disabled for the BMC to control host power-on and
+		 * reset.
 		 */
-		if ((desc->reg == HW_STRAP1 || desc->reg == HW_STRAP2) &&
-				desc->ip == ASPEED_IP_SCU)
+		if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP1 &&
+		    !(desc->mask & (BIT(21) | BIT(22))))
+			continue;
+
+		if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP2)
 			continue;
 
 		ret = regmap_update_bits(maps[desc->ip], desc->reg,
Signature · 1 line
2.11.0.483.g087da7b7c-goog
#1 lore raw
Quoted 7 lines · Rick Altherr

Port D and port E GPIO loopback modes are commonly enabled via hardware straps for use with front-panel buttons. When the BMC is powered off or fails to boot, the front-panel buttons are directly connected to the host chipset via the loopback to allow direct power-on and reset control. Once the BMC has booted, the loopback mode must be disabled for the BMC to take over control of host power-on and reset.

Quoted 8 lines

Disabling these loopback modes requires writing to the hardware strap register which violates the current design of assuming the system designer chose the strap settings for a specific reason and they should be treated as read-only. Only the two bits of the strap register related to these loopback modes are allowed to be written and comments have been added to explain why.

Patch applied with the ACKs for v4.12.

Yours,
Linus Walleij