Skip to contentSkip to conversation

drm/vc4: Fix DSI T_INIT timing.

PATCH New Eric Anholt 1 participant 2 messages Mar 17, 2017

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 drm/vc4: Fix DSI T_INIT timing.

The DPHY spec requires a much larger T_INIT than I was specifying before. In the absence of clear specs from the slave of what their timing is, just use the value that the firmware was using.

---
 drivers/gpu/drm/vc4/vc4_dsi.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_dsi.c +11 -1
index 160f981d1cf4..3bad8bad32a2 100644
@@ -1094,7 +1094,17 @@ static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
 				     DSI_HS_DLT4_TRAIL) |
 		       VC4_SET_FIELD(0, DSI_HS_DLT4_ANLAT));
 
-	DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000, 5000),
+	/* T_INIT is how long STOP is driven after power-up to
+	 * indicate to the slave (also coming out of power-up) that
+	 * master init is complete, and should be greater than the
+	 * maximum of two value: T_INIT,MASTER and T_INIT,SLAVE.  The
+	 * D-PHY spec gives a minimum 100us for T_INIT,MASTER and
+	 * T_INIT,SLAVE, while allowing protocols on top of it to give
+	 * greater minimums.  The vc4 firmware uses an extremely
+	 * conservative 5ms, and we maintain that here.
+	 */
+	DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns,
+							    5 * 1000 * 1000, 0),
 					      DSI_HS_DLT5_INIT));
 
 	DSI_PORT_WRITE(HS_DLT6,
Signature · 6 lines
2.11.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#1 lore raw

PATCH 2/2 drm/vc4: Fix misleading name of the continuous flag.

The logic was all right in the end, the name was just backwards.

---
 drivers/gpu/drm/vc4/vc4_dsi.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/vc4/vc4_dsi.c +4 -4
index 3bad8bad32a2..deba62008fd0 100644
@@ -820,18 +820,18 @@ static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch)
 /* Enters or exits Ultra Low Power State. */
 static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps)
 {
-	bool continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS;
-	u32 phyc_ulps = ((continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) |
+	bool non_continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	u32 phyc_ulps = ((non_continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) |
 			 DSI_PHYC_DLANE0_ULPS |
 			 (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) |
 			 (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) |
 			 (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0));
-	u32 stat_ulps = ((continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) |
+	u32 stat_ulps = ((non_continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) |
 			 DSI1_STAT_PHY_D0_ULPS |
 			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) |
 			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) |
 			 (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0));
-	u32 stat_stop = ((continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) |
+	u32 stat_stop = ((non_continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) |
 			 DSI1_STAT_PHY_D0_STOP |
 			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) |
 			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) |
Signature · 6 lines
2.11.0

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel