Skip to contentSkip to conversation

Maximum Transmit Power for channel 36 ,40,44 and 48

DISCUSSION KAVITA MATHUR 3 participants 4 messages Mar 20, 2017 – Mar 21, 2017 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hi,

Chipset : AR9220
RF module : WLM200NX and WLM200N5
Linux Kernel : 3.12
ath9k driver : backport4.4.2-1

With above combination , I have measured maximum transmit power 13 dBm for channel 36,40,44 and 48. While it is 20 dBm for channel 149 and other 5GHz band channels
as well as for 2.4 GHz channels.

If I try to set txpower using iwconfig wlan0 txpower 20 , it gives no error.but it shows only 13dBM.

How I can change the txpower for channel 36,40,44 and 48?

Please help me on this.

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw

Am 20.03.2017 um 09:25 schrieb KAVITA MATHUR:

Quoted 7 lines

Hi,

Chipset : AR9220
RF module : WLM200NX and WLM200N5
Linux Kernel : 3.12
ath9k driver : backport4.4.2-1

Quoted 8 lines

With above combination , I have measured maximum transmit power 13 dBm for channel 36,40,44 and 48. While it is 20 dBm for channel 149 and other 5GHz band channels
as well as for 2.4 GHz channels.

If I try to set txpower using iwconfig wlan0 txpower 20 , it gives no error.but it shows only 13dBM.

How I can change the txpower for channel 36,40,44 and 48?

the maximum availale txpower depends on the calibration data which is stored within the cards owm eeprom and is also related to the current used mcs set / wireless rate. as higher the rate is as lower the transmission power will be
according to the datasheet the rate for ht40 5 ghz for this card is 14 dbm at MCS 7 / 15 with a tollerance of +- 2 dbm

https://www.pcengines.ch/pdf/wlm200n5-23.pdf

Sebastian

Quoted 18 lines

Please help me on this.

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 17 lines
Mit freundlichen Grüssen / Regards

Sebastian Gottschall / CTO

NewMedia-NET GmbH - DD-WRT
Firmensitz:  Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: [email protected]
Tel.: +496251-582650 / Fax: +496251-5826565


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#2 lore raw

Hi,

But I got 13 dBm for 20 MHz channel(HT20), mcs 7. And I got 18dBm for 40 MHz channel(HT40), mcs 15. In both cases, I have set channel 36.

If I change channel 36 to 149, I always get 20dBm for all the modes(legacy,HT-20 and HT-40).

I am using country IN in my hostapd configuration file, which gives following limitation:

country IN: DFS-JP

        (2402 - 2482 @ 40), (20)
        (5170 - 5250 @ 80), (20), AUTO-BW
        (5250 - 5330 @ 80), (20), DFS, AUTO-BW
        (5735 - 5835 @ 80), (20)

Can I change the calibration data? How can it be done?

Thanks & Regards,
KAvita

On Mon, 20 Mar 2017 11:45:16 +0100, Sebastian Gottschall wrote

Quoted 41 lines

Am 20.03.2017 um 09:25 schrieb KAVITA MATHUR:

Quoted 7 lines

Hi,

Chipset : AR9220
RF module : WLM200NX and WLM200N5
Linux Kernel : 3.12
ath9k driver : backport4.4.2-1

Quoted 8 lines

With above combination , I have measured maximum transmit power 13 dBm for channel 36,40,44 and 48. While it is 20 dBm for channel 149 and other 5GHz band channels
as well as for 2.4 GHz channels.

If I try to set txpower using iwconfig wlan0 txpower 20 , it gives no error.but it shows only 13dBM.

How I can change the txpower for channel 36,40,44 and 48?

the maximum availale txpower depends on the calibration data which is stored within the cards owm eeprom and is also related to the current used mcs set / wireless rate.
as higher the rate is as lower the transmission power will be according to the datasheet the rate for ht40 5 ghz for this card is 14 dbm at MCS 7 / 15 with a tollerance of +- 2 dbm

https://www.pcengines.ch/pdf/wlm200n5-23.pdf

Sebastian

Quoted 14 lines

Please help me on this.

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

Quoted 17 lines
Quoted 4 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 11 lines
Mit freundlichen Grüssen / Regards

Sebastian Gottschall / CTO

NewMedia-NET GmbH - DD-WRT
Firmensitz:  Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: [email protected]
Tel.: +496251-582650 / Fax: +496251-5826565

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#3 lore raw

hiya,

sure, but the NIC also has calibration tables for the maximum power it's been calibrated at for each channel. This includes per-channel targets and band-edge targets.

Unfortunately :( ath10k doesn't easily expose the NIC regulatory / CTL entries in a useful fashion. That would sure be nice.

-adrian

Quoted 93 lines · KAVITA MATHUR

Hi,

But I got 13 dBm for 20 MHz channel(HT20), mcs 7. And I got 18dBm for 40 MHz channel(HT40), mcs 15. In both cases, I have set channel 36.

If I change channel 36 to 149, I always get 20dBm for all the modes(legacy,HT-20 and HT-40).

I am using country IN in my hostapd configuration file, which gives following limitation:

country IN: DFS-JP

        (2402 - 2482 @ 40), (20)
        (5170 - 5250 @ 80), (20), AUTO-BW
        (5250 - 5330 @ 80), (20), DFS, AUTO-BW
        (5735 - 5835 @ 80), (20)

Can I change the calibration data? How can it be done?

Thanks & Regards,
KAvita

On Mon, 20 Mar 2017 11:45:16 +0100, Sebastian Gottschall wrote

Quoted 51 lines

Am 20.03.2017 um 09:25 schrieb KAVITA MATHUR:

Quoted 7 lines

Hi,

Chipset : AR9220
RF module : WLM200NX and WLM200N5
Linux Kernel : 3.12
ath9k driver : backport4.4.2-1

Quoted 8 lines

With above combination , I have measured maximum transmit power 13 dBm for channel 36,40,44 and 48. While it is 20 dBm for channel 149 and other 5GHz band channels
as well as for 2.4 GHz channels.

If I try to set txpower using iwconfig wlan0 txpower 20 , it gives no error.but it shows only 13dBM.

How I can change the txpower for channel 36,40,44 and 48?

the maximum availale txpower depends on the calibration data which is stored within the cards owm eeprom and is also related to the current used mcs set / wireless rate.
as higher the rate is as lower the transmission power will be according to the datasheet the rate for ht40 5 ghz for this card is 14 dbm at MCS 7 / 15 with a tollerance of +- 2 dbm

https://www.pcengines.ch/pdf/wlm200n5-23.pdf

Sebastian

Quoted 14 lines

Please help me on this.

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

Quoted 4 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

--
Mit freundlichen Grüssen / Regards

Sebastian Gottschall / CTO

Quoted 7 lines

NewMedia-NET GmbH - DD-WRT
Firmensitz: Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473 Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: [email protected]
Tel.: +496251-582650 / Fax: +496251-5826565

Thanks & Regards,
कविता माथुर Kavita Mathur
वरिष्ठ अनुसंधान अभियंता Senior Research Engineer
सी-डॉट C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I
होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100
फोन Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it

Quoted 4 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k