pitft: Add support for pitft35r
PATCH 1/1 pitft: Add support for pitft35r
The support for the PiTFT 3.5 inch resistive touchscreen is optional. It may be enabled by adding the following line in local.conf:
MACHINE_FEATURES += "pitft pitft35r"
--- README | 1 + conf/machine/include/rpi-base.inc | 1 + conf/machine/raspberrypi3-64.conf | 1 + recipes-bsp/bootfiles/rpi-config_git.bb | 6 ++++++ 4 files changed, 9 insertions(+)
README +1 -0
@@ -240,6 +240,7 @@ the modelname should be added as a MACHINE_FEATURES in local.conf like below: List of currently supported models: - pitft22 - pitft28r + - pitft35r 3.O. Enable UART ===============
conf/machine/include/rpi-base.inc +1 -0
@@ -31,6 +31,7 @@ KERNEL_DEVICETREE ?= " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \
conf/machine/raspberrypi3-64.conf +1 -0
@@ -23,6 +23,7 @@ KERNEL_DEVICETREE = " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \
recipes-bsp/bootfiles/rpi-config_git.bb +6 -0
@@ -18,6 +18,7 @@ PR = "r5" PITFT="${@bb.utils.contains("MACHINE_FEATURES", "pitft", "1", "0", d)}" PITFT22="${@bb.utils.contains("MACHINE_FEATURES", "pitft22", "1", "0", d)}" PITFT28r="${@bb.utils.contains("MACHINE_FEATURES", "pitft28r", "1", "0", d)}" +PITFT35r="${@bb.utils.contains("MACHINE_FEATURES", "pitft35r", "1", "0", d)}" VC4GRAPHICS="${@bb.utils.contains("MACHINE_FEATURES", "vc4graphics", "1", "0", d)}"
@@ -99,6 +100,11 @@ do_deploy() { echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt fi + if [ "${PITFT35r}" = "1" ]; then + echo "# Enable PITFT35r display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + fi + # UART support if [ "${ENABLE_UART}" = "1" ]; then echo "# Enable UART" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
Signature · 1 line
2.11.0
Quoted 5 lines · Rob Woolley
The support for the PiTFT 3.5 inch resistive touchscreen is optional. It may be enabled by adding the following line in local.conf:
MACHINE_FEATURES+= "pitft pitft35r"
Looks ok, I have staged it.
Quoted 69 lines
Signed-off-by Rob Woolley <[email protected]>--- README | 1 + conf/machine/include/rpi-base.inc | 1 + conf/machine/raspberrypi3-64.conf | 1 + recipes-bsp/bootfiles/rpi-config_git.bb | 6 ++++++ 4 files changed, 9 insertions(+)README +1
-0@@ -240,6 +240,7 @@ the modelname should be added as a MACHINE_FEATURES in local.conf like below: List of currently supported models: - pitft22 - pitft28r + - pitft35r 3.O. Enable UART ===============conf/machine/include/rpi-base.inc +1
-0@@ -31,6 +31,7 @@ KERNEL_DEVICETREE ?= " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \conf/machine/raspberrypi3-64.conf +1
-0@@ -23,6 +23,7 @@ KERNEL_DEVICETREE = " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \recipes-bsp/bootfiles/rpi-config_git.bb +6
-0@@ -18,6 +18,7 @@ PR = "r5" PITFT="${@bb.utils.contains("MACHINE_FEATURES", "pitft", "1", "0", d)}" PITFT22="${@bb.utils.contains("MACHINE_FEATURES", "pitft22", "1", "0", d)}" PITFT28r="${@bb.utils.contains("MACHINE_FEATURES", "pitft28r", "1", "0", d)}" +PITFT35r="${@bb.utils.contains("MACHINE_FEATURES", "pitft35r", "1", "0", d)}" VC4GRAPHICS="${@bb.utils.contains("MACHINE_FEATURES", "vc4graphics", "1", "0", d)}"@@ -99,6 +100,11 @@ do_deploy() { echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt fi + if [ "${PITFT35r}" = "1" ]; then + echo "# Enable PITFT35r display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + fi + # UART support if [ "${ENABLE_UART}" = "1" ]; then echo "# Enable UART" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
Quoted 74 lines · Rob Woolley
The support for the PiTFT 3.5 inch resistive touchscreen is optional. It may be enabled by adding the following line in local.conf:
MACHINE_FEATURES+= "pitft pitft35r"Signed-off-by Rob Woolley <[email protected]>--- README | 1 + conf/machine/include/rpi-base.inc | 1 + conf/machine/raspberrypi3-64.conf | 1 + recipes-bsp/bootfiles/rpi-config_git.bb | 6 ++++++ 4 files changed, 9 insertions(+)README +1
-0@@ -240,6 +240,7 @@ the modelname should be added as a MACHINE_FEATURES in local.conf like below: List of currently supported models: - pitft22 - pitft28r + - pitft35r 3.O. Enable UART ===============conf/machine/include/rpi-base.inc +1
-0@@ -31,6 +31,7 @@ KERNEL_DEVICETREE ?= " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \conf/machine/raspberrypi3-64.conf +1
-0@@ -23,6 +23,7 @@ KERNEL_DEVICETREE = " \ overlays/lirc-rpi.dtbo \ overlays/pitft22.dtbo \ overlays/pitft28-resistive.dtbo \ + overlays/pitft35-resistive.dtbo \ overlays/pps-gpio.dtbo \ overlays/rpi-ft5406.dtbo \ overlays/w1-gpio.dtbo \recipes-bsp/bootfiles/rpi-config_git.bb +6
-1@@ -18,6 +18,7 @@ PR = "r5" PITFT="${@bb.utils.contains("MACHINE_FEATURES", "pitft", "1", "0", d)}" PITFT22="${@bb.utils.contains("MACHINE_FEATURES", "pitft22", "1", "0", d)}" PITFT28r="${@bb.utils.contains("MACHINE_FEATURES", "pitft28r", "1", "0", d)}" +PITFT35r="${@bb.utils.contains("MACHINE_FEATURES", "pitft35r", "1", "0", d)}" VC4GRAPHICS="${@bb.utils.contains("MACHINE_FEATURES", "vc4graphics", "1", "0", d)}"@@ -99,6 +100,11 @@ do_deploy() { echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt fi + if [ "${PITFT35r}" = "1" ]; then + echo "# Enable PITFT35r display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt + fi + # UART support if [ "${ENABLE_UART}" = "1" ]; then echo "# Enable UART" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt --
Quoted 2 lines
2.11.0
This commit looks fine but I would prefer having separate commits:
1. Documentation commit
2. dtbo inclusion
3. and rpi-config changes
Could you resend this commit please?
--
Andrei Gherzan
gpg: rsa4096/D4D94F67AD0E9640 | t: @agherzan