Skip to contentSkip to conversation

linux-firmware: Bring up wifi/ble interface on rpi3

PATCH In review Andrei Gherzan 1 participant 8 messages Apr 17, 2017 – Apr 19, 2017 Broadcom BCM2711/BCM2835 Arm architecture

lore
Share & tools
lore
#0 lore raw

PATCH 1/7 linux-firmware: Bring up wifi/ble interface on rpi3

From: Khem Raj <[email protected]>

Currently the firmware is installed but kernel fails to load it due this .txt file missing in the firmware directory and it ends up with wifi/bluetooth i/f not being initialized. The error is also in dmesg

[    3.120991] usbcore: registered new interface driver brcmfmac
[    3.148240] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.txt failed with error -2

After applying this patch now ifconfig -a can list wlan0 interface successfully.

---
 .../linux-firmware/files/brcmfmac43430-sdio.txt    | 66 ++++++++++++++++++++++
 .../linux-firmware/linux-firmware_%.bbappend       | 12 ++++
 2 files changed, 78 insertions(+)
 create mode 100644 recipes-kernel/linux-firmware/files/brcmfmac43430-sdio.txt
 create mode 100644 recipes-kernel/linux-firmware/linux-firmware_%.bbappend
recipes-kernel/linux-firmware/files/brcmfmac43430-sdio.txt new file +66 -0
new file mode 100644
index 0000000..ea4f648
@@ -0,0 +1,66 @@
+# NVRAM file for BCM943430WLPTH
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0727
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0727
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+boardflags3=0x08000000
+xtalfreq=37400
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=84
+txpwrbckof=6
+cckbw202gpo=0
+legofdmbw202gpo=0x66111111
+mcsbw202gpo=0x77711111
+propbw202gpo=0xdd
+
+# OFDM IIR :
+ofdmdigfilttype=18
+ofdmdigfilttypebe=18
+# PAPD mode:
+papdmode=1
+papdvalidtest=1
+pacalidx2g=42
+papdepsoffset=-22
+papdendidx=58
+
+# LTECX flags
+ltecxmux=0
+ltecxpadnum=0x0102
+ltecxfnsel=0x44
+ltecxgcigpio=0x01
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG
+muxenab=0x1
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+
+#VCO freq 326.4MHz
+spurconfig=0x3 
+
+edonthd20l=-75
+edoffthd20ul=-80
recipes-kernel/linux-firmware/linux-firmware_%.bbappend new file +12 -0
new file mode 100644
index 0000000..252da22
@@ -0,0 +1,12 @@
+FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
+
+SRC_URI += "file://brcmfmac43430-sdio.txt"
+
+do_install_append() {
+	install -D -m 0644 ${WORKDIR}/brcmfmac43430-sdio.txt ${D}/lib/firmware/brcm/brcmfmac43430-sdio.txt
+}
+
+FILES_${PN}-bcm43430 += " \
+  /lib/firmware/brcm/brcmfmac43430-sdio.txt \
+"
+
Signature · 1 line
2.12.2
#1 lore raw

PATCH 2/7 firmware: Update to 20161215 release

From: Khem Raj <[email protected]>

---
 recipes-bsp/common/firmware.inc | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
recipes-bsp/common/firmware.inc +3 -3
index 1961b48..8aea628 100644
@@ -1,10 +1,10 @@
-RPIFW_DATE ?= "20161125"
+RPIFW_DATE ?= "20161215"
 RPIFW_SRC_URI ?= "https://github.com/raspberrypi/firmware/archive/1.${RPIFW_DATE}.tar.gz"
 RPIFW_S ?= "${WORKDIR}/firmware-1.${RPIFW_DATE}"
 
 SRC_URI = "${RPIFW_SRC_URI}"
-SRC_URI[md5sum] = "a9281d2869e2d7673a83d41bacfa66c2"
-SRC_URI[sha256sum] = "744e050630621c70991c91e0ee8663dc2f579e743583ca762b13b00bc75859bc"
+SRC_URI[md5sum] = "ddd7645988360d7ef267b48c32293ad7"
+SRC_URI[sha256sum] = "bda18f2affb50053940fd88c3f3bec5af9a4b4ced753d01107a2b106cfb02d13"
 
 PV = "${RPIFW_DATE}"
 
Signature · 1 line
2.12.2
#2 lore raw

PATCH 3/7 firmware: Update to 20170303 release

In reply to Andrei Gherzan

From: Khem Raj <[email protected]>

Uses 4.9.13 and has rpi0w support

---
 recipes-bsp/common/firmware.inc | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
recipes-bsp/common/firmware.inc +3 -3
index 8aea628..53c469e 100644
@@ -1,10 +1,10 @@
-RPIFW_DATE ?= "20161215"
+RPIFW_DATE ?= "20170303"
 RPIFW_SRC_URI ?= "https://github.com/raspberrypi/firmware/archive/1.${RPIFW_DATE}.tar.gz"
 RPIFW_S ?= "${WORKDIR}/firmware-1.${RPIFW_DATE}"
 
 SRC_URI = "${RPIFW_SRC_URI}"
-SRC_URI[md5sum] = "ddd7645988360d7ef267b48c32293ad7"
-SRC_URI[sha256sum] = "bda18f2affb50053940fd88c3f3bec5af9a4b4ced753d01107a2b106cfb02d13"
+SRC_URI[md5sum] = "c87bc1bffbb8f254fc739e34baa03b02"
+SRC_URI[sha256sum] = "ee8758d7e63c8fea7c8b7b476ff1c09f9591c74349b7751036a78ae5b88eca36"
 
 PV = "${RPIFW_DATE}"
 
Signature · 1 line
2.12.2
#3 lore raw

PATCH 4/7 firmware.inc: Bump to 20170405

In reply to Andrei Gherzan
---
 recipes-bsp/common/firmware.inc | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
recipes-bsp/common/firmware.inc +3 -3
index 53c469e..1c3a911 100644
@@ -1,10 +1,10 @@
-RPIFW_DATE ?= "20170303"
+RPIFW_DATE ?= "20170405"
 RPIFW_SRC_URI ?= "https://github.com/raspberrypi/firmware/archive/1.${RPIFW_DATE}.tar.gz"
 RPIFW_S ?= "${WORKDIR}/firmware-1.${RPIFW_DATE}"
 
 SRC_URI = "${RPIFW_SRC_URI}"
-SRC_URI[md5sum] = "c87bc1bffbb8f254fc739e34baa03b02"
-SRC_URI[sha256sum] = "ee8758d7e63c8fea7c8b7b476ff1c09f9591c74349b7751036a78ae5b88eca36"
+SRC_URI[md5sum] = "ea82d14a7cd8cfae9b78e00d4e56bc71"
+SRC_URI[sha256sum] = "2f4e5bddbac1372590db203002c35cbba3fb9d6172a93c314ee27bf05ae13bff"
 
 PV = "${RPIFW_DATE}"
 
Signature · 1 line
2.12.2
#4 lore raw

PATCH 5/7 rpi-base.inc: Include dtb for RPI0 WiFi

In reply to Andrei Gherzan
---
 conf/machine/include/rpi-base.inc | 1 +
 1 file changed, 1 insertion(+)
conf/machine/include/rpi-base.inc +1 -0
index e069e70..dc98099 100644
@@ -14,6 +14,7 @@ XSERVER = " \
     "
 
 KERNEL_DEVICETREE ?= " \
+    bcm2708-rpi-0-w.dtb \
     bcm2708-rpi-b.dtb \
     bcm2708-rpi-b-plus.dtb \
     bcm2709-rpi-2-b.dtb \
Signature · 1 line
2.12.2
#5 lore raw

PATCH 6/7 raspberrypi0-wifi.conf: Add machine configuration file

In reply to Andrei Gherzan
---
 conf/machine/raspberrypi0-wifi.conf | 11 +++++++++++
 1 file changed, 11 insertions(+)
 create mode 100644 conf/machine/raspberrypi0-wifi.conf
conf/machine/raspberrypi0-wifi.conf new file +11 -0
new file mode 100644
index 0000000..2b7cea4
@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: RaspberryPi Zero WiFi Development Board
+#@DESCRIPTION: Machine configuration for the RaspberryPi Zero  WiFi board (https://www.raspberrypi.org/blog/raspberry-pi-zero-w-joins-family/)
+
+MACHINEOVERRIDES = "raspberrypi:${MACHINE}"
+include conf/machine/raspberrypi.conf
+
+MACHINE_EXTRA_RRECOMMENDS += "linux-firmware-bcm43430"
+
+SERIAL_CONSOLE = "115200 ttyS0"
+VC4_CMA_SIZE ?= "cma-128"
Signature · 1 line
2.12.2
#6 lore raw

PATCH 7/7 README: Add info about raspberrypi0-wifi

In reply to Andrei Gherzan
---
 README | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
README +4 -4
index 65a1e5f..17f8273 100644
@@ -77,6 +77,7 @@ b. Add needed layer to bblayers.conf:
 c. Set MACHINE in local.conf to one of the supported boards:
     - raspberrypi
     - raspberrypi0
+    - raspberrypi0-wifi
     - raspberrypi2
     - raspberrypi3
     - raspberrypi-cm (dummy alias for raspberrypi)
@@ -243,11 +244,10 @@ List of currently supported models:
 
 3.O. Enable UART
 ===============
+RaspberryPi 0, 1, 2 and CM will have UART console enabled by default.
 
-RaspberryPi 1, 2 and CM will have UART console enabled by default.
-
-RaspberryPi 3 does not have the UART enabled by default because this needs a
-fixed core frequency and enable_uart wil set it to the minimum. Certain
+RaspberryPi 0 WiFi and 3 does not have the UART enabled by default because this
+needs a fixed core frequency and enable_uart wil set it to the minimum. Certain
 operations - 60fps h264 decode, high quality deinterlace - which aren't
 performed on the ARM may be affected, and we wouldn't want to do that to users
 who don't want to use the serial port. Users who want serial console support on
Signature · 1 line
2.12.2
#7 lore raw
In reply to Andrei Gherzan
Quoted 113 lines · Andrei Gherzan

From: Khem Raj <[email protected]>

Currently the firmware is installed but kernel fails to load it due this .txt file missing in the firmware directory and it ends up with wifi/bluetooth i/f not being initialized. The error is also in dmesg

[    3.120991] usbcore: registered new interface driver brcmfmac
[    3.148240] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.txt failed with error -2

After applying this patch now ifconfig -a can list wlan0 interface successfully.

---
 .../linux-firmware/files/brcmfmac43430-sdio.txt    | 66 ++++++++++++++++++++++
 .../linux-firmware/linux-firmware_%.bbappend       | 12 ++++
 2 files changed, 78 insertions(+)
 create mode 100644 recipes-kernel/linux-firmware/files/brcmfmac43430-sdio.txt
 create mode 100644 recipes-kernel/linux-firmware/linux-firmware_%.bbappend
recipes-kernel/linux-firmware/files/brcmfmac43430-sdio.txt new file +66 -0
new file mode 100644
index 0000000..ea4f648
@@ -0,0 +1,66 @@
+# NVRAM file for BCM943430WLPTH
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0727
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0727
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+boardflags3=0x08000000
+xtalfreq=37400
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=84
+txpwrbckof=6
+cckbw202gpo=0
+legofdmbw202gpo=0x66111111
+mcsbw202gpo=0x77711111
+propbw202gpo=0xdd
+
+# OFDM IIR :
+ofdmdigfilttype=18
+ofdmdigfilttypebe=18
+# PAPD mode:
+papdmode=1
+papdvalidtest=1
+pacalidx2g=42
+papdepsoffset=-22
+papdendidx=58
+
+# LTECX flags
+ltecxmux=0
+ltecxpadnum=0x0102
+ltecxfnsel=0x44
+ltecxgcigpio=0x01
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG
+muxenab=0x1
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+
+#VCO freq 326.4MHz
+spurconfig=0x3
+
+edonthd20l=-75
+edoffthd20ul=-80
recipes-kernel/linux-firmware/linux-firmware_%.bbappend new file +12 -1
new file mode 100644
index 0000000..252da22
@@ -0,0 +1,12 @@
+FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
+
+SRC_URI += "file://brcmfmac43430-sdio.txt"
+
+do_install_append() {
+	install -D -m 0644 ${WORKDIR}/brcmfmac43430-sdio.txt ${D}/lib/firmware/brcm/brcmfmac43430-sdio.txt
+}
+
+FILES_${PN}-bcm43430 += " \
+  /lib/firmware/brcm/brcmfmac43430-sdio.txt \
+"
+
--
Quoted 2 lines

2.12.2

Merged series to morty.

--
Andrei Gherzan
gpg: rsa4096/D4D94F67AD0E9640 | t: @agherzan