Skip to contentSkip to conversation

README: remove irrelevant information

PATCH In review Trevor Woerner 3 participants 3 messages Apr 30, 2017 – May 6, 2017

lore
Share & tools
lore

Trevor Woerner

author
#0 lore raw

PATCH 1/1 README: remove irrelevant information

As of openembedded-core commit 2b3ae58f5eaecc8474761c543ff5347aa0e3c4c8 hardfp is enabled by default.

Signed-off-by Trevor Woerner <[email protected]>
---
 README | 16 ----------------
 1 file changed, 16 deletions(-)
README +0 -16
index b2e89f3..7f4a499 100644
@@ -49,7 +49,6 @@ Table of Contents
   I. Configure yocto/oe environment
  II. Building a second level bootloader based on kexec
 III. Booting your device
- IV. Performance
 
 I. Configure yocto/oe environment
 ========================================

@@ -127,18 +126,3 @@ linux-next from tftp='tftp://192.168.0.5/zImage dtb=tftp://192.168.0.5/<MACHINE>
 Then, plug your SDCARD into your Rockchip device and power on the board. If
 everything worked fine, Petitboot should be started automatically and list all 
 entries found in the configuration file.
-
-IV. Performance
-===============
-
-By default a BSP layer should not be tuning a build, this is a DISTRO-level
-decision. As such the default machine settings are meant to be the lowest
-common denominator in order to maximize generality. If you are interested in
-tweaking your build to maximize performance you can either use a DISTRO that
-has these same goals, or you can add settings in your configuration files
-(e.g. local.conf) as follows:
-
-	for rk3288:
-		DEFAULTTUNE = "cortexa17hf-neon-vfpv4"
-	for rk3066:
-		DEFAULTTUNE = "cortexa9-neon"
Signature · 1 line
2.12.0.rc1.48.g076c053
#1 lore raw

Hello,

Even if I agree with the reason of why you want to remove this section. I think , it might be a good point to keep a note about this in the README. Just explain that this is not up to the bsp layer to do this, but to the distro (a short sentence).

What do you think ?
Romain

2017-04-30 4:23 GMT+02:00 Trevor Woerner <[email protected]>:

Quoted 55 lines

As of openembedded-core commit 2b3ae58f5eaecc8474761c543ff5347aa0e3c4c8 hardfp
is enabled by default.

Signed-off-by Trevor Woerner <[email protected]>
---
 README | 16 ----------------
 1 file changed, 16 deletions(-)
README +0 -1
index b2e89f3..7f4a499 100644
@@ -49,7 +49,6 @@ Table of Contents
   I. Configure yocto/oe environment
  II. Building a second level bootloader based on kexec
 III. Booting your device
- IV. Performance
 
 I. Configure yocto/oe environment
 ========================================

@@ -127,18 +126,3 @@ linux-next from tftp='tftp://192.168.0.5/zImage

dtb=tftp://192.168.0.5/<MACHINE>
Then, plug your SDCARD into your Rockchip device and power on the board.
If
everything worked fine, Petitboot should be started automatically and
list all
entries found in the configuration file.

README +0 -5
-
-IV. Performance
-===============
-
-By default a BSP layer should not be tuning a build, this is a

DISTRO-level

README +0 -2
-decision. As such the default machine settings are meant to be the lowest
-common denominator in order to maximize generality. If you are interested

in
-tweaking your build to maximize performance you can either use a DISTRO that

README +0 -8
-has these same goals, or you can add settings in your configuration files
-(e.g. local.conf) as follows:
-
-       for rk3288:
-               DEFAULTTUNE = "cortexa17hf-neon-vfpv4"
-       for rk3066:
-               DEFAULTTUNE = "cortexa9-neon"
--

2.12.0.rc1.48.g076c053

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

#2 lore raw
Quoted 8 lines · Romain Perier

Hello,

Even if I agree with the reason of why you want to remove this section. I think , it might be a good point to keep a note about this in the README. Just explain that this is not up to the bsp layer to do this, but to the distro (a short sentence).

What do you think ?

You can put something like distro guidelines. Although I would refrain

Quoted 68 lines

Romain

2017-04-30 4:23 GMT+02:00 Trevor Woerner <[email protected]>:

Quoted 50 lines

As of openembedded-core commit 2b3ae58f5eaecc8474761c543ff5347aa0e3c4c8 hardfp
is enabled by default.

Signed-off-by Trevor Woerner <[email protected]>
---
 README | 16 ----------------
 1 file changed, 16 deletions(-)
README +0 -1
index b2e89f3..7f4a499 100644
@@ -49,7 +49,6 @@ Table of Contents
   I. Configure yocto/oe environment
  II. Building a second level bootloader based on kexec
 III. Booting your device
- IV. Performance
 
 I. Configure yocto/oe environment
 ========================================

@@ -127,18 +126,3 @@ linux-next from tftp='tftp://192.168.0.5/zImage

dtb=tftp://192.168.0.5/<MACHINE>
Then, plug your SDCARD into your Rockchip device and power on the board.
If
everything worked fine, Petitboot should be started automatically and
list all
entries found in the configuration file.

README +0 -5
-
-IV. Performance
-===============
-
-By default a BSP layer should not be tuning a build, this is a

DISTRO-level

README +0 -2
-decision. As such the default machine settings are meant to be the lowest
-common denominator in order to maximize generality. If you are interested

in
-tweaking your build to maximize performance you can either use a DISTRO that

README +0 -8
-has these same goals, or you can add settings in your configuration files
-(e.g. local.conf) as follows:
-
-       for rk3288:
-               DEFAULTTUNE = "cortexa17hf-neon-vfpv4"
-       for rk3066:
-               DEFAULTTUNE = "cortexa9-neon"
--

2.12.0.rc1.48.g076c053

Quoted 5 lines

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto