Skip to contentSkip to conversation

Improve --lookup command to allow register names.

PATCH New Tom St Denis 1 participant 1 message Jul 5, 2017

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Improve --lookup command to allow register names.

This is handy if you are given a debug output with a register name and value you want to decode. For instance, a VM fault in the kernel log,

$ umr -i 1 -O bits --lookup mmVM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0803D00C
gmc81.mmVM_CONTEXT1_PROTECTION_FAULT_STATUS => 0x0803d00c
        .PROTECTIONS[0:7]                                                ==       12 (0x0000000c)
        .MEMORY_CLIENT_ID[12:20]                                         ==       61 (0x0000003d)
        .MEMORY_CLIENT_RW[24:24]                                         ==        0 (0x00000000)
        .VMID[25:28]                                                     ==        4 (0x00000004)
        .ATOMIC[29:29]                                                   ==        0 (0x00000000)
---
 doc/umr.1            |  5 +++--
 src/app/main.c       |  6 +++++-
 src/app/umr_lookup.c | 41 ++++++++++++++++++++++++++++-------------
 3 files changed, 36 insertions(+), 16 deletions(-)
doc/umr.1 +3 -2
index d20184def2d3..601866a57a7e 100644
@@ -32,8 +32,9 @@ Enumerate all AMDGPU supported devices.
 List all blocks attached to the asic that has been detected.
 .IP "--list-regs, -lr <string>"
 List all registers in an IP block (can use '-O bits' to list bitfields)
-.IP "--lookup, -lu <address> <number>"
-Look up an MMIO register by address and bitfield decode the value specified.
+.IP "--lookup, -lu <address_or_regname> <number>"
+Look up an MMIO register by address and bitfield decode the value specified (with 0x prefix) or by
+register name.
 .IP "--write -w <string> <number>"
 Write a value specified in hex to a register specified with a complete
 register path in the form <
src/app/main.c +5 -1
index 822aa88afd85..ac3c25e2937e 100644
@@ -393,12 +393,16 @@ int main(int argc, char **argv)
 "\n\t--bank, -b <se_bank> <sh_bank> <instance>\n\t\tSelect a GFX INSTANCE/SH/SE bank in decimal. Can use 'x' to denote broadcast.\n"
 "\n\t--force, -f <number>\n\t\tForce a PCIE DID number in hex or asic name.  Useful if amdgpu is"
 	"\n\t\tnot loaded or a display is not attached.\n"
+"\n\t--pci <device>"
+	"\n\t\tForce a specific PCI device using the domain:bus:slot.function format in hex."
+	"\n\t\tThis is useful when more than one GPU is available. If the amdgpu driver is"
+	"\n\t\tloaded the corresponding instance will be automatically detected.\n"
 "\n\t--print, -p\n\t\tEnable dumping of all device registers. (default: off)\n"
 "\n\t--config, -c\n\t\tPrint out configuation data read from kernel driver.\n"
 "\n\t--enumerate, -e\n\t\tEnumerate all AMDGPU devices detected.\n"
 "\n\t--list-blocks, -lb\n\t\tList IP blocks discovered for this device.\n"
 "\n\t--list-regs, -lr <string>\n\t\tList registers for a given IP block (can use '-O bits' to list bitfields).\n"
-"\n\t--lookup, -lu <address> <value>\n\t\tLook up bit decoding of an MMIO register by address.\n"
+"\n\t--lookup, -lu <address_or_regname> <value>\n\t\tLook up bit decoding of an MMIO register by address (with 0x prefix) or by register name.\n"
 "\n\t--write, -w <address> <number>\n\t\tWrite a value in hex to a register specified as a register path in the"
 	"\n\t\tform <asicname.ipname.regname>.  For instance \"tonga.uvd5.mmUVD_SOFT_RESET\"."
 	"\n\t\tCan be used multiple times to set multiple registers.  You can"
src/app/umr_lookup.c +28 -13

51 lines not on this page · raw message

Signature · 6 lines
2.12.0

_______________________________________________
amd-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/amd-gfx