m68k: add board stmark2, mcf5441x based
Subsystems (2)
PATCH 1/1 m68k: add board stmark2, mcf5441x based
Signed-off-by Angelo Dureghello <[email protected]>
--- arch/m68k/Kconfig | 5 + board/sysam/stmark2/Kconfig | 15 +++ board/sysam/stmark2/MAINTAINERS | 6 ++ board/sysam/stmark2/Makefile | 8 ++ board/sysam/stmark2/sbf_dram_init.S | 119 +++++++++++++++++++++ board/sysam/stmark2/stmark2.c | 47 +++++++++ configs/stmark2_defconfig | 26 +++++ include/configs/stmark2.h | 202 ++++++++++++++++++++++++++++++++++++ scripts/config_whitelist.txt | 1 + 9 files changed, 429 insertions(+) create mode 100644 board/sysam/stmark2/Kconfig create mode 100644 board/sysam/stmark2/MAINTAINERS create mode 100644 board/sysam/stmark2/Makefile create mode 100644 board/sysam/stmark2/sbf_dram_init.S create mode 100644 board/sysam/stmark2/stmark2.c create mode 100644 configs/stmark2_defconfig create mode 100644 include/configs/stmark2.h
arch/m68k/Kconfig +5 -0
@@ -200,6 +200,10 @@ config TARGET_AMCORE bool "Support AMCORE" select M5307 +config TARGET_STMARK2 + bool "Support stmark2" + select M54418 + endchoice source "board/BuS/eb_cpu5282/Kconfig"
@@ -223,5 +227,6 @@ source "board/freescale/m54455evb/Kconfig" source "board/freescale/m547xevb/Kconfig" source "board/freescale/m548xevb/Kconfig" source "board/sysam/amcore/Kconfig" +source "board/sysam/stmark2/Kconfig" endmenu
board/sysam/stmark2/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_STMARK2 + +config SYS_CPU + default "mcf5445x" + +config SYS_BOARD + default "stmark2" + +config SYS_VENDOR + default "sysam" + +config SYS_CONFIG_NAME + default "stmark2" + +endif
board/sysam/stmark2/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +STMARK2 BOARD +M: Angelo Dureghello <[email protected]> +S: Maintained +F: board/sysam/stmark2/ +F: include/configs/stmark2.h +F: configs/stmark2_defconfig
board/sysam/stmark2/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# +# (C) Copyright 2014 Angelo Dureghello <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = stmark2.o +extra-y += sbf_dram_init.o
board/sysam/stmark2/sbf_dram_init.S new file +119 -0
119 lines not on this page · raw message
board/sysam/stmark2/stmark2.c new file +47 -0
47 lines not on this page · raw message
configs/stmark2_defconfig new file +26 -0
@@ -0,0 +1,26 @@ +CONFIG_M68K=y +CONFIG_SYS_TEXT_BASE=0x47E00000 +CONFIG_TARGET_STMARK2=y +CONFIG_SYS_EXTRA_OPTIONS="CF_SBF,SYS_SERIAL_BOOT,SYS_INPUT_CLKSRC=30000000" +# CONFIG_DISPLAY_BOARDINFO is not set +# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="stmark2 $ " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_LOADB=y +# CONFIG_CMD_LOADS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +# CONFIG_CMD_FPGA is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_NET is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_CACHE=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_REGEX=y
include/configs/stmark2.h new file +202 -0
202 lines not on this page · raw message
scripts/config_whitelist.txt +1 -0
@@ -2696,6 +2696,7 @@ CONFIG_STM32_GPIO CONFIG_STM32_HSE_HZ CONFIG_STM32_HZ CONFIG_STM32_SERIAL +CONFIG_STMARK2 CONFIG_STRESS CONFIG_STRIDER CONFIG_STRIDER_CON
Signature · 1 line
2.13.2
PATCH 1/1 m68k: add board stmark2, mcf5441x based
Quoted 20 lines · Angelo Dureghello
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig | 5 + board/sysam/stmark2/Kconfig | 15 +++ board/sysam/stmark2/MAINTAINERS | 6 ++ board/sysam/stmark2/Makefile | 8 ++ board/sysam/stmark2/sbf_dram_init.S | 119 +++++++++++++++++++++ board/sysam/stmark2/stmark2.c | 47 +++++++++ configs/stmark2_defconfig | 26 +++++ include/configs/stmark2.h | 202 ++++++++++++++++++++++++++++++++++++ scripts/config_whitelist.txt | 1 + 9 files changed, 429 insertions(+) create mode 100644 board/sysam/stmark2/Kconfig create mode 100644 board/sysam/stmark2/MAINTAINERS create mode 100644 board/sysam/stmark2/Makefile create mode 100644 board/sysam/stmark2/sbf_dram_init.S create mode 100644 board/sysam/stmark2/stmark2.c create mode 100644 configs/stmark2_defconfig create mode 100644 include/configs/stmark2.h
[...]
Quoted 21 lines
include/configs/stmark2.h new file +15
-0@@ -0,0 +1,202 @@ +/* +* Sysam stmark2 board configuration +* +* (C) Copyright 2016 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __STMARK2_CONFIG_H +#define __STMARK2_CONFIG_H + +#define CONFIG_STMARK2 +#define CONFIG_HOSTNAME stmark2 + +#define CONFIG_MCFUART
include/configs/stmark2.h line 25
Quoted 10 lines
include/configs/stmark2.h new file +10
-0+#define CONFIG_SYS_UART_PORT 0 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define LDS_BOARD_TEXT \ + board/sysam/stmark2/sbf_dram_init.o (.text*) + +#define CONFIG_TIMESTAMP + +/* commands */ +#define CONFIG_CMD_REGINFO
CMD_REGINFO is only on PowerPC 8xx, 85xx and 86xx
Christophe
Quoted 183 lines
include/configs/stmark2.h new file +177
-0+ +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 root=/dev/ram0 rw " \ + "rootfstype=ramfs " \ + "rdinit=/bin/init " \ + "devtmpfs.mount=1" + +#define CONFIG_BOOTCOMMAND \ + "sf probe 0:1 50000000; " \ + "sf read ${loadaddr} 0x100000 ${kern_size}; " \ + "bootm ${loadaddr}" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kern_size=0x700000\0" \ + "loadaddr=0x40001000\0" \ + "-(rootfs)\0" \ + "update_uboot=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0 0x80000; " \ + "sf write ${loadaddr} 0 ${filesize}\0" \ + "update_kernel=loady ${loadaddr}; " \ + "setenv kern_size ${filesize}; saveenv; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x100000 0x700000; " \ + "sf write ${loadaddr} 0x100000 ${filesize}\0" \ + "update_rootfs=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x00800000 0x100000; " \ + "sf write ${loadaddr} 0x00800000 ${filesize}\0" \ + "" + +/* Realtime clock */ +#undef CONFIG_MCFRTC +#define CONFIG_RTC_MCFRRTC +#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 + +/* spi not partitions */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" +#define MTDIDS_DEFAULT "nor0=spi-flash.0" +#define MTDPARTS_DEFAULT \ + "mtdparts=spi-flash.0:" \ + "1m(u-boot)," \ + "7m(kernel)," \ + "-(rootfs)" + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* DSPI and Serial Flash */ +#define CONFIG_CF_SPI +#define CONFIG_CF_DSPI +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SERIAL_FLASH +#define CONFIG_HARD_SPI +#define CONFIG_SPI_FLASH_ISSI +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 1 + +#define CONFIG_SYS_SBFHDR_SIZE 0x7 + +#define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ + DSPI_CTAR_PCSSCK_1CLK | \ + DSPI_CTAR_PASC(0) | \ + DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(0) | \ + DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(1) | \ + DSPI_CTAR_BR(6)) +#define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) +#define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 2048/* 2048 KB */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) +#define CONFIG_SYS_MBAR 0xFC000000 + +/* +* Definitions for initial stack pointer and data area (in internal SRAM) +*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +/* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) - 32) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) + +/* +* Start addresses for the final memory configuration +* (Set up by the startup code) +* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 +*/ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 128/* SDRAM size in MB */ + +#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) +#define CONFIG_SYS_DRAM_TEST + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_SERIAL_BOOT +#endif + +#if defined(CONFIG_SERIAL_BOOT ) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +/* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) + +/* +* For booting Linux, the board info and command line data +* have to be in the first 8 MB of memory, since this is +* the maximum mapped by the Linux kernel during initialization ?? +*/ +/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* Configuration for environment +* Environment is embedded in u-boot in the second sector of the flash +*/ + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_ENV_IS_IN_SPI_FLASH 1 +#define CONFIG_ENV_SPI_CS 1 +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#endif + +#undef CONFIG_ENV_OVERWRITE + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + +#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 12) + +#endif /* __STMARK2_CONFIG_H */ scripts/config_whitelist.txt +0
-0
scripts/config_whitelist.txt CONFIG_STM32_GPIO · line 2702
Quoted 7 lines
scripts/config_whitelist.txt +1
-0@@ -2696,6 +2696,7 @@ CONFIG_STM32_GPIO CONFIG_STM32_HSE_HZ CONFIG_STM32_HZ CONFIG_STM32_SERIAL +CONFIG_STMARK2 CONFIG_STRESS CONFIG_STRIDER CONFIG_STRIDER_CON
---
L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast.
https://www.avast.com/antivirus
PATCH 1/1 m68k: add board stmark2, mcf5441x based
Hi Christophe,
Quoted 51 lines · christophe leroy
Quoted 20 lines · Angelo Dureghello
Signed-off-by Angelo Dureghello <[email protected]>--- arch/m68k/Kconfig | 5 + board/sysam/stmark2/Kconfig | 15 +++ board/sysam/stmark2/MAINTAINERS | 6 ++ board/sysam/stmark2/Makefile | 8 ++ board/sysam/stmark2/sbf_dram_init.S | 119 +++++++++++++++++++++ board/sysam/stmark2/stmark2.c | 47 +++++++++ configs/stmark2_defconfig | 26 +++++ include/configs/stmark2.h | 202 ++++++++++++++++++++++++++++++++++++ scripts/config_whitelist.txt | 1 + 9 files changed, 429 insertions(+) create mode 100644 board/sysam/stmark2/Kconfig create mode 100644 board/sysam/stmark2/MAINTAINERS create mode 100644 board/sysam/stmark2/Makefile create mode 100644 board/sysam/stmark2/sbf_dram_init.S create mode 100644 board/sysam/stmark2/stmark2.c create mode 100644 configs/stmark2_defconfig create mode 100644 include/configs/stmark2.h[...]
Quoted 25 lines
include/configs/stmark2.h new file +19
-0@@ -0,0 +1,202 @@ +/* +* Sysam stmark2 board configuration +* +* (C) Copyright 2016 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __STMARK2_CONFIG_H +#define __STMARK2_CONFIG_H + +#define CONFIG_STMARK2 +#define CONFIG_HOSTNAME stmark2 + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT 0 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define LDS_BOARD_TEXT \
Quoted 9 lines
include/configs/stmark2.h line 25
Quoted 6 lines
include/configs/stmark2.h new file +6
-0+ board/sysam/stmark2/sbf_dram_init.o (.text*) + +#define CONFIG_TIMESTAMP + +/* commands */ +#define CONFIG_CMD_REGINFO
CMD_REGINFOis only on PowerPC 8xx, 85xx and 86xx
thanks, checking / fixing.
Quoted 188 lines
Christophe
Quoted 186 lines
include/configs/stmark2.h new file +177
-0+ +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 root=/dev/ram0 rw " \ + "rootfstype=ramfs " \ + "rdinit=/bin/init " \ + "devtmpfs.mount=1" + +#define CONFIG_BOOTCOMMAND \ + "sf probe 0:1 50000000; " \ + "sf read ${loadaddr} 0x100000 ${kern_size}; " \ + "bootm ${loadaddr}" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kern_size=0x700000\0" \ + "loadaddr=0x40001000\0" \ + "-(rootfs)\0" \ + "update_uboot=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0 0x80000; " \ + "sf write ${loadaddr} 0 ${filesize}\0" \ + "update_kernel=loady ${loadaddr}; " \ + "setenv kern_size ${filesize}; saveenv; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x100000 0x700000; " \ + "sf write ${loadaddr} 0x100000 ${filesize}\0" \ + "update_rootfs=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x00800000 0x100000; " \ + "sf write ${loadaddr} 0x00800000 ${filesize}\0" \ + "" + +/* Realtime clock */ +#undef CONFIG_MCFRTC +#define CONFIG_RTC_MCFRRTC +#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 + +/* spi not partitions */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" +#define MTDIDS_DEFAULT "nor0=spi-flash.0" +#define MTDPARTS_DEFAULT \ + "mtdparts=spi-flash.0:" \ + "1m(u-boot)," \ + "7m(kernel)," \ + "-(rootfs)" + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* DSPI and Serial Flash */ +#define CONFIG_CF_SPI +#define CONFIG_CF_DSPI +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SERIAL_FLASH +#define CONFIG_HARD_SPI +#define CONFIG_SPI_FLASH_ISSI +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 1 + +#define CONFIG_SYS_SBFHDR_SIZE 0x7 + +#define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ + DSPI_CTAR_PCSSCK_1CLK | \ + DSPI_CTAR_PASC(0) | \ + DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(0) | \ + DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(1) | \ + DSPI_CTAR_BR(6)) +#define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) +#define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 2048/* 2048 KB */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) +#define CONFIG_SYS_MBAR 0xFC000000 + +/* +* Definitions for initial stack pointer and data area (in internal SRAM) +*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +/* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) - 32) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) + +/* +* Start addresses for the final memory configuration +* (Set up by the startup code) +* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 +*/ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 128/* SDRAM size in MB */ + +#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) +#define CONFIG_SYS_DRAM_TEST + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_SERIAL_BOOT +#endif + +#if defined(CONFIG_SERIAL_BOOT ) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +/* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) + +/* +* For booting Linux, the board info and command line data +* have to be in the first 8 MB of memory, since this is +* the maximum mapped by the Linux kernel during initialization ?? +*/ +/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* Configuration for environment +* Environment is embedded in u-boot in the second sector of the flash +*/ + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_ENV_IS_IN_SPI_FLASH 1 +#define CONFIG_ENV_SPI_CS 1 +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#endif + +#undef CONFIG_ENV_OVERWRITE + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + +#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 12) + +#endif /* __STMARK2_CONFIG_H */ scripts/config_whitelist.txt +1
-0@@ -2696,6 +2696,7 @@ CONFIG_STM32_GPIO CONFIG_STM32_HSE_HZ CONFIG_STM32_HZ CONFIG_STM32_SERIAL +CONFIG_STMARK2
Quoted 9 lines
scripts/config_whitelist.txt CONFIG_STM32_GPIO · line 2702
Quoted 4 lines
scripts/config_whitelist.txt +0
-0CONFIG_STRESS CONFIG_STRIDER CONFIG_STRIDER_CON---
L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast.
https://www.avast.com/antivirus
Regards,
Angelo Dureghello
PATCH 1/1 m68k: add board stmark2, mcf5441x based
In reply to Angelo DureghelloHi Angelo,
Quoted 1 line · Angelo Dureghello
Signed-off-by Angelo Dureghello <[email protected]>
Can you please write something about your board in the commit message?
Quoted 467 lines
--- arch/m68k/Kconfig | 5 + board/sysam/stmark2/Kconfig | 15 +++ board/sysam/stmark2/MAINTAINERS | 6 ++ board/sysam/stmark2/Makefile | 8 ++ board/sysam/stmark2/sbf_dram_init.S | 119 +++++++++++++++++++++ board/sysam/stmark2/stmark2.c | 47 +++++++++ configs/stmark2_defconfig | 26 +++++ include/configs/stmark2.h | 202 ++++++++++++++++++++++++++++++++++++ scripts/config_whitelist.txt | 1 + 9 files changed, 429 insertions(+) create mode 100644 board/sysam/stmark2/Kconfig create mode 100644 board/sysam/stmark2/MAINTAINERS create mode 100644 board/sysam/stmark2/Makefile create mode 100644 board/sysam/stmark2/sbf_dram_init.S create mode 100644 board/sysam/stmark2/stmark2.c create mode 100644 configs/stmark2_defconfig create mode 100644 include/configs/stmark2.harch/m68k/Kconfig +5
-0@@ -200,6 +200,10 @@ config TARGET_AMCORE bool "Support AMCORE" select M5307 +config TARGET_STMARK2 + bool "Support stmark2" + select M54418 + endchoice source "board/BuS/eb_cpu5282/Kconfig"@@ -223,5 +227,6 @@ source "board/freescale/m54455evb/Kconfig" source "board/freescale/m547xevb/Kconfig" source "board/freescale/m548xevb/Kconfig" source "board/sysam/amcore/Kconfig" +source "board/sysam/stmark2/Kconfig" endmenuboard/sysam/stmark2/Kconfig new file +15
-0@@ -0,0 +1,15 @@ +if TARGET_STMARK2 + +config SYS_CPU + default "mcf5445x" + +config SYS_BOARD + default "stmark2" + +config SYS_VENDOR + default "sysam" + +config SYS_CONFIG_NAME + default "stmark2" + +endifboard/sysam/stmark2/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +STMARK2 BOARD +M: Angelo Dureghello <[email protected]> +S: Maintained +F: board/sysam/stmark2/ +F: include/configs/stmark2.h +F: configs/stmark2_defconfigboard/sysam/stmark2/Makefile new file +8
-0@@ -0,0 +1,8 @@ +# +# (C) Copyright 2014 Angelo Dureghello <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = stmark2.o +extra-y += sbf_dram_init.oboard/sysam/stmark2/sbf_dram_init.S new file +119
-0@@ -0,0 +1,119 @@ +/* + * Board-specific early ddr/sdram init. + * + * (C) Copyright 2017 Angelo Dureghello <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +.equ PPMCR0, 0xfc04002d +.equ MSCR_SDRAMC, 0xec094060 +.equ MISCCR2, 0xec09001a +.equ DDR_RCR, 0xfc0b8180 +.equ DDR_PADCR, 0xfc0b81ac +.equ DDR_CR00, 0xfc0b8000 +.equ DDR_CR06, 0xfc0b8018 +.equ DDR_CR09, 0xfc0b8024 +.equ DDR_CR40, 0xfc0b80a0 +.equ DDR_CR45, 0xfc0b80b4 +.equ DDR_CR56, 0xfc0b80e0 + +.global sbf_dram_init +.text + +sbf_dram_init: + /* CD46 = DDR on */ + move.l #PPMCR0, %a1 + move.b #46, (%a1) + + /* stmark 2, max drive strength */ + move.l #MSCR_SDRAMC, %a1 + move.b #1, (%a1) + + /* + * use cpu clock, seems more realiable + * + * DDR2 clock is serviced from DDR controller as input clock / 2 + * so, if clock comes from + * vco, i.e. 480(vco) / 2, so ddr clock is 240 Mhz (measured) + * cpu, i.e. 250(cpu) / 2, so ddr clock is 125 Mhz (measured) + * + * . + * / \ DDR2 can't be clocked lower than 125Mhz + * / ! \ DDR2 init must pass further i/dcache enable test + * /_____\ + * WARNING + */ + + /* cpu / 2 = 125 Mhz for 480 Mhz pll */ + move.l #MISCCR2, %a1 + move.w #0xa01d, (%a1) + + /* DDR force sw reset settings */ + move.l #DDR_RCR, %a1 + move.l #0x00000000, (%a1) + move.l #0x40000000, (%a1) + + /* + * PAD_ODT_CS: for us seems both 1(75 ohm) and 2(150ohm) are good, + * 500/700 mV are ok + */ + move.l #DDR_PADCR, %a1 + move.l #0x01030203, (%a1) /* as freescale tower */ + + move.l #DDR_CR00, %a1 + move.l #0x01010101, (%a1)+ /* 0x00 */ + move.l #0x00000101, (%a1)+ /* 0x04 */ + move.l #0x01010100, (%a1)+ /* 0x08 */ + move.l #0x01010000, (%a1)+ /* 0x0C */ + move.l #0x00010101, (%a1)+ /* 0x10 */ + move.l #DDR_CR06, %a1 + move.l #0x00010100, (%a1)+ /* 0x18 */ + move.l #0x00000001, (%a1)+ /* 0x1C */ + move.l #0x01000001, (%a1)+ /* 0x20 */ + move.l #0x00000100, (%a1)+ /* 0x24 */ + move.l #0x00010001, (%a1)+ /* 0x28 */ + move.l #0x00000200, (%a1)+ /* 0x2C */ + move.l #0x01000002, (%a1)+ /* 0x30 */ + move.l #0x00000000, (%a1)+ /* 0x34 */ + move.l #0x00000100, (%a1)+ /* 0x38 */ + move.l #0x02000100, (%a1)+ /* 0x3C */ + move.l #0x02000407, (%a1)+ /* 0x40 */ + move.l #0x02030007, (%a1)+ /* 0x44 */ + move.l #0x02000100, (%a1)+ /* 0x48 */ + move.l #0x0A030203, (%a1)+ /* 0x4C */ + move.l #0x00020708, (%a1)+ /* 0x50 */ + move.l #0x00050008, (%a1)+ /* 0x54 */ + move.l #0x04030002, (%a1)+ /* 0x58 */ + move.l #0x00000004, (%a1)+ /* 0x5C */ + move.l #0x020A0000, (%a1)+ /* 0x60 */ + move.l #0x0C00000E, (%a1)+ /* 0x64 */ + move.l #0x00002004, (%a1)+ /* 0x68 */ + move.l #0x00000000, (%a1)+ /* 0x6C */ + move.l #0x00100010, (%a1)+ /* 0x70 */ + move.l #0x00100010, (%a1)+ /* 0x74 */ + move.l #0x00000000, (%a1)+ /* 0x78 */ + move.l #0x07990000, (%a1)+ /* 0x7C */ + move.l #DDR_CR40, %a1 + move.l #0x00000000, (%a1)+ /* 0xA0 */ + move.l #0x00C80064, (%a1)+ /* 0xA4 */ + move.l #0x44520002, (%a1)+ /* 0xA8 */ + move.l #0x00C80023, (%a1)+ /* 0xAC */ + move.l #DDR_CR45, %a1 + move.l #0x0000C350, (%a1) /* 0xB4 */ + move.l #DDR_CR56, %a1 + move.l #0x04000000, (%a1)+ /* 0xE0 */ + move.l #0x03000304, (%a1)+ /* 0xE4 */ + move.l #0x40040000, (%a1)+ /* 0xE8 */ + move.l #0xC0004004, (%a1)+ /* 0xEC */ + move.l #0x0642C000, (%a1)+ /* 0xF0 */ + move.l #0x00000642, (%a1)+ /* 0xF4 */ + move.l #DDR_CR09, %a1 + tpf + move.l #0x01000100, (%a1) /* 0x24 */ + + move.l #0x2000, %d1 + bsr asm_delay + + + rtsboard/sysam/stmark2/stmark2.c new file +47
-0@@ -0,0 +1,47 @@ +/* +* Board-specific init. +* +* (C) Copyright 2017 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <spi.h> +#include <asm/io.h> +#include <asm/immap.h> +#include <mmc.h> +#include <fsl_esdhc.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int checkboard (void ) +{ +/* +* need to to: +* Check serial flash size. if 2mb evb, else 8mb demo +*/ +puts ("Board: " ); +puts ("Sysam stmark2\n" ); +return 0 ; +} + +int dram_init (void ) +{ +u32 dramsize; + +/* +* Serial Boot: The dram is already initialized in start.S +* only require to return DRAM size +*/ + dramsize =CONFIG_SYS_SDRAM_SIZE *0x100000 ; + + gd->ram_size = dramsize; + +return 0 ; +} + +int testdram (void ) +{ +return 0 ; +}configs/stmark2_defconfig new file +26
-0@@ -0,0 +1,26 @@ +CONFIG_M68K=y +CONFIG_SYS_TEXT_BASE=0x47E00000 +CONFIG_TARGET_STMARK2=y +CONFIG_SYS_EXTRA_OPTIONS="CF_SBF,SYS_SERIAL_BOOT,SYS_INPUT_CLKSRC=30000000" +# CONFIG_DISPLAY_BOARDINFO is not set +# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="stmark2 $ " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_LOADB=y +# CONFIG_CMD_LOADS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +# CONFIG_CMD_FPGA is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_NET is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_CACHE=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_REGEX=yinclude/configs/stmark2.h new file +163
-0@@ -0,0 +1,202 @@ +/* +* Sysam stmark2 board configuration +* +* (C) Copyright 2016 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __STMARK2_CONFIG_H +#define __STMARK2_CONFIG_H + +#define CONFIG_STMARK2 +#define CONFIG_HOSTNAME stmark2 + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT 0 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define LDS_BOARD_TEXT \ + board/sysam/stmark2/sbf_dram_init.o (.text*) + +#define CONFIG_TIMESTAMP + +/* commands */ +#define CONFIG_CMD_REGINFO + +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 root=/dev/ram0 rw " \ + "rootfstype=ramfs " \ + "rdinit=/bin/init " \ + "devtmpfs.mount=1" + +#define CONFIG_BOOTCOMMAND \ + "sf probe 0:1 50000000; " \ + "sf read ${loadaddr} 0x100000 ${kern_size}; " \ + "bootm ${loadaddr}" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kern_size=0x700000\0" \ + "loadaddr=0x40001000\0" \ + "-(rootfs)\0" \ + "update_uboot=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0 0x80000; " \ + "sf write ${loadaddr} 0 ${filesize}\0" \ + "update_kernel=loady ${loadaddr}; " \ + "setenv kern_size ${filesize}; saveenv; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x100000 0x700000; " \ + "sf write ${loadaddr} 0x100000 ${filesize}\0" \ + "update_rootfs=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x00800000 0x100000; " \ + "sf write ${loadaddr} 0x00800000 ${filesize}\0" \ + "" + +/* Realtime clock */ +#undef CONFIG_MCFRTC +#define CONFIG_RTC_MCFRRTC +#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 + +/* spi not partitions */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" +#define MTDIDS_DEFAULT "nor0=spi-flash.0" +#define MTDPARTS_DEFAULT \ + "mtdparts=spi-flash.0:" \ + "1m(u-boot)," \ + "7m(kernel)," \ + "-(rootfs)" + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* DSPI and Serial Flash */ +#define CONFIG_CF_SPI +#define CONFIG_CF_DSPI +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SERIAL_FLASH +#define CONFIG_HARD_SPI +#define CONFIG_SPI_FLASH_ISSI +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 1 + +#define CONFIG_SYS_SBFHDR_SIZE 0x7 + +#define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ + DSPI_CTAR_PCSSCK_1CLK | \ + DSPI_CTAR_PASC(0) | \ + DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(0) | \ + DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(1) | \ + DSPI_CTAR_BR(6)) +#define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) +#define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 2048/* 2048 KB */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) +#define CONFIG_SYS_MBAR 0xFC000000 + +/* +* Definitions for initial stack pointer and data area (in internal SRAM) +*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +/* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) - 32) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) + +/* +* Start addresses for the final memory configuration +* (Set up by the startup code) +* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 +*/ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 128/* SDRAM size in MB */ + +#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) +#define CONFIG_SYS_DRAM_TEST + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_SERIAL_BOOT +#endif + +#if defined(CONFIG_SERIAL_BOOT ) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +/* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) + +/* +* For booting Linux, the board info and command line data +* have to be in the first 8 MB of memory, since this is +* the maximum mapped by the Linux kernel during initialization ?? +*/
include/configs/stmark2.h line 173
Quoted 10 lines
include/configs/stmark2.h new file +10
-0+/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* Configuration for environment +* Environment is embedded in u-boot in the second sector of the flash +*/ + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_ENV_IS_IN_SPI_FLASH 1
This is now in Kconfig.
Quoted 34 lines
include/configs/stmark2.h new file +29
-0+#define CONFIG_ENV_SPI_CS 1 +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#endif + +#undef CONFIG_ENV_OVERWRITE + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + +#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 12) + +#endif /* __STMARK2_CONFIG_H */ scripts/config_whitelist.txt +0
-0
scripts/config_whitelist.txt CONFIG_STM32_GPIO · line 2699
Quoted 4 lines
scripts/config_whitelist.txt +1
-0@@ -2696,6 +2696,7 @@ CONFIG_STM32_GPIO CONFIG_STM32_HSE_HZ CONFIG_STM32_HZ CONFIG_STM32_SERIAL +CONFIG_STMARK2
We should stop adding ad-hoc CONFIG_xxx. Please use Kconfig.
scripts/config_whitelist.txt CONFIG_STM32_GPIO
Quoted 4 lines
scripts/config_whitelist.txt +0
-1CONFIG_STRESS CONFIG_STRIDER CONFIG_STRIDER_CON --
Regards,
Bin
PATCH 1/1 m68k: add board stmark2, mcf5441x based
Hi Bin,
Quoted 6 lines · Bin Meng
Hi Angelo,
Quoted 1 line · Angelo Dureghello
Signed-off-by Angelo Dureghello <[email protected]>Can you please write something about your board in the commit message?
sure, sending patch v2.
Quoted 522 lines
Quoted 468 lines
--- arch/m68k/Kconfig | 5 + board/sysam/stmark2/Kconfig | 15 +++ board/sysam/stmark2/MAINTAINERS | 6 ++ board/sysam/stmark2/Makefile | 8 ++ board/sysam/stmark2/sbf_dram_init.S | 119 +++++++++++++++++++++ board/sysam/stmark2/stmark2.c | 47 +++++++++ configs/stmark2_defconfig | 26 +++++ include/configs/stmark2.h | 202 ++++++++++++++++++++++++++++++++++++ scripts/config_whitelist.txt | 1 + 9 files changed, 429 insertions(+)create mode 100644 board/sysam/stmark2/Kconfig create mode 100644 board/sysam/stmark2/MAINTAINERS create mode 100644 board/sysam/stmark2/Makefile create mode 100644
board/sysam/stmark2/sbf_dram_init.Screate mode 100644board/sysam/stmark2/stmark2.ccreate mode 100644 configs/stmark2_defconfig create mode 100644include/configs/stmark2.harch/m68k/Kconfig +5
-0@@ -200,6 +200,10 @@ config TARGET_AMCORE bool "Support AMCORE" select M5307 +config TARGET_STMARK2 + bool "Support stmark2" + select M54418 + endchoice source "board/BuS/eb_cpu5282/Kconfig"@@ -223,5 +227,6 @@ source "board/freescale/m54455evb/Kconfig" source "board/freescale/m547xevb/Kconfig" source "board/freescale/m548xevb/Kconfig" source "board/sysam/amcore/Kconfig" +source "board/sysam/stmark2/Kconfig" endmenuboard/sysam/stmark2/Kconfig new file +15
-0@@ -0,0 +1,15 @@ +if TARGET_STMARK2 + +config SYS_CPU + default "mcf5445x" + +config SYS_BOARD + default "stmark2" + +config SYS_VENDOR + default "sysam" + +config SYS_CONFIG_NAME + default "stmark2" + +endifboard/sysam/stmark2/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +STMARK2 BOARD +M: Angelo Dureghello <[email protected]> +S: Maintained +F: board/sysam/stmark2/ +F: include/configs/stmark2.h +F: configs/stmark2_defconfigboard/sysam/stmark2/Makefile new file +8
-0@@ -0,0 +1,8 @@ +# +# (C) Copyright 2014 Angelo Dureghello <[email protected]> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = stmark2.o +extra-y += sbf_dram_init.oboard/sysam/stmark2/sbf_dram_init.S new file +119
-0@@ -0,0 +1,119 @@ +/* + * Board-specific early ddr/sdram init. + * + * (C) Copyright 2017 Angelo Dureghello <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +.equ PPMCR0, 0xfc04002d +.equ MSCR_SDRAMC, 0xec094060 +.equ MISCCR2, 0xec09001a +.equ DDR_RCR, 0xfc0b8180 +.equ DDR_PADCR, 0xfc0b81ac +.equ DDR_CR00, 0xfc0b8000 +.equ DDR_CR06, 0xfc0b8018 +.equ DDR_CR09, 0xfc0b8024 +.equ DDR_CR40, 0xfc0b80a0 +.equ DDR_CR45, 0xfc0b80b4 +.equ DDR_CR56, 0xfc0b80e0 + +.global sbf_dram_init +.text + +sbf_dram_init: + /* CD46 = DDR on */ + move.l #PPMCR0, %a1 + move.b #46, (%a1) + + /* stmark 2, max drive strength */ + move.l #MSCR_SDRAMC, %a1 + move.b #1, (%a1) + + /* + * use cpu clock, seems more realiable + * + * DDR2 clock is serviced from DDR controller as input clock / 2 + * so, if clock comes from + * vco, i.e. 480(vco) / 2, so ddr clock is 240 Mhz (measured) + * cpu, i.e. 250(cpu) / 2, so ddr clock is 125 Mhz (measured) + * + * . + * / \ DDR2 can't be clocked lower than 125Mhz + * / ! \ DDR2 init must pass further i/dcache enable test + * /_____\ + * WARNING + */ + + /* cpu / 2 = 125 Mhz for 480 Mhz pll */ + move.l #MISCCR2, %a1 + move.w #0xa01d, (%a1) + + /* DDR force sw reset settings */ + move.l #DDR_RCR, %a1 + move.l #0x00000000, (%a1) + move.l #0x40000000, (%a1) + + /* + * PAD_ODT_CS: for us seems both 1(75 ohm) and 2(150ohm) are good, + * 500/700 mV are ok + */ + move.l #DDR_PADCR, %a1 + move.l #0x01030203, (%a1) /* as freescale tower */ + + move.l #DDR_CR00, %a1 + move.l #0x01010101, (%a1)+ /* 0x00 */ + move.l #0x00000101, (%a1)+ /* 0x04 */ + move.l #0x01010100, (%a1)+ /* 0x08 */ + move.l #0x01010000, (%a1)+ /* 0x0C */ + move.l #0x00010101, (%a1)+ /* 0x10 */ + move.l #DDR_CR06, %a1 + move.l #0x00010100, (%a1)+ /* 0x18 */ + move.l #0x00000001, (%a1)+ /* 0x1C */ + move.l #0x01000001, (%a1)+ /* 0x20 */ + move.l #0x00000100, (%a1)+ /* 0x24 */ + move.l #0x00010001, (%a1)+ /* 0x28 */ + move.l #0x00000200, (%a1)+ /* 0x2C */ + move.l #0x01000002, (%a1)+ /* 0x30 */ + move.l #0x00000000, (%a1)+ /* 0x34 */ + move.l #0x00000100, (%a1)+ /* 0x38 */ + move.l #0x02000100, (%a1)+ /* 0x3C */ + move.l #0x02000407, (%a1)+ /* 0x40 */ + move.l #0x02030007, (%a1)+ /* 0x44 */ + move.l #0x02000100, (%a1)+ /* 0x48 */ + move.l #0x0A030203, (%a1)+ /* 0x4C */ + move.l #0x00020708, (%a1)+ /* 0x50 */ + move.l #0x00050008, (%a1)+ /* 0x54 */ + move.l #0x04030002, (%a1)+ /* 0x58 */ + move.l #0x00000004, (%a1)+ /* 0x5C */ + move.l #0x020A0000, (%a1)+ /* 0x60 */ + move.l #0x0C00000E, (%a1)+ /* 0x64 */ + move.l #0x00002004, (%a1)+ /* 0x68 */ + move.l #0x00000000, (%a1)+ /* 0x6C */ + move.l #0x00100010, (%a1)+ /* 0x70 */ + move.l #0x00100010, (%a1)+ /* 0x74 */ + move.l #0x00000000, (%a1)+ /* 0x78 */ + move.l #0x07990000, (%a1)+ /* 0x7C */ + move.l #DDR_CR40, %a1 + move.l #0x00000000, (%a1)+ /* 0xA0 */ + move.l #0x00C80064, (%a1)+ /* 0xA4 */ + move.l #0x44520002, (%a1)+ /* 0xA8 */ + move.l #0x00C80023, (%a1)+ /* 0xAC */ + move.l #DDR_CR45, %a1 + move.l #0x0000C350, (%a1) /* 0xB4 */ + move.l #DDR_CR56, %a1 + move.l #0x04000000, (%a1)+ /* 0xE0 */ + move.l #0x03000304, (%a1)+ /* 0xE4 */ + move.l #0x40040000, (%a1)+ /* 0xE8 */ + move.l #0xC0004004, (%a1)+ /* 0xEC */ + move.l #0x0642C000, (%a1)+ /* 0xF0 */ + move.l #0x00000642, (%a1)+ /* 0xF4 */ + move.l #DDR_CR09, %a1 + tpf + move.l #0x01000100, (%a1) /* 0x24 */ + + move.l #0x2000, %d1 + bsr asm_delay + + + rtsboard/sysam/stmark2/stmark2.c new file +47
-0@@ -0,0 +1,47 @@ +/* +* Board-specific init. +* +* (C) Copyright 2017 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <spi.h> +#include <asm/io.h> +#include <asm/immap.h> +#include <mmc.h> +#include <fsl_esdhc.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int checkboard (void ) +{ +/* +* need to to: +* Check serial flash size. if 2mb evb, else 8mb demo +*/ +puts ("Board: " ); +puts ("Sysam stmark2\n" ); +return 0 ; +} + +int dram_init (void ) +{ +u32 dramsize; + +/* +* Serial Boot: The dram is already initialized in start.S +* only require to return DRAM size +*/ + dramsize =CONFIG_SYS_SDRAM_SIZE *0x100000 ; + + gd->ram_size = dramsize; + +return 0 ; +} + +int testdram (void ) +{ +return 0 ; +}configs/stmark2_defconfig new file +26
-0@@ -0,0 +1,26 @@ +CONFIG_M68K=y +CONFIG_SYS_TEXT_BASE=0x47E00000 +CONFIG_TARGET_STMARK2=y +CONFIG_SYS_EXTRA_OPTIONS="CF_SBF,SYS_SERIAL_BOOT,SYS_INPUT_CLKSRC=30000000" +# CONFIG_DISPLAY_BOARDINFO is not set +# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="stmark2 $ " +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_CONSOLE is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_LOADB=y +# CONFIG_CMD_LOADS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +# CONFIG_CMD_FPGA is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_NET is not set +# CONFIG_CMD_NFS is not set +CONFIG_CMD_CACHE=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_REGEX=yinclude/configs/stmark2.h new file +163
-0@@ -0,0 +1,202 @@ +/* +* Sysam stmark2 board configuration +* +* (C) Copyright 2016 Angelo Dureghello <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __STMARK2_CONFIG_H +#define __STMARK2_CONFIG_H + +#define CONFIG_STMARK2 +#define CONFIG_HOSTNAME stmark2 + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT 0 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define LDS_BOARD_TEXT \ + board/sysam/stmark2/sbf_dram_init.o (.text*) + +#define CONFIG_TIMESTAMP + +/* commands */ +#define CONFIG_CMD_REGINFO + +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 root=/dev/ram0 rw " \ + "rootfstype=ramfs " \ + "rdinit=/bin/init " \ + "devtmpfs.mount=1" + +#define CONFIG_BOOTCOMMAND \ + "sf probe 0:1 50000000; " \ + "sf read ${loadaddr} 0x100000 ${kern_size}; " \ + "bootm ${loadaddr}" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kern_size=0x700000\0" \ + "loadaddr=0x40001000\0" \ + "-(rootfs)\0" \ + "update_uboot=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0 0x80000; " \ + "sf write ${loadaddr} 0 ${filesize}\0" \ + "update_kernel=loady ${loadaddr}; " \ + "setenv kern_size ${filesize}; saveenv; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x100000 0x700000; " \ + "sf write ${loadaddr} 0x100000 ${filesize}\0" \ + "update_rootfs=loady ${loadaddr}; " \ + "sf probe 0:1 50000000; " \ + "sf erase 0x00800000 0x100000; " \ + "sf write ${loadaddr} 0x00800000 ${filesize}\0" \ + "" + +/* Realtime clock */ +#undef CONFIG_MCFRTC +#define CONFIG_RTC_MCFRRTC +#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 + +/* spi not partitions */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_JFFS2_CMDLINE +#define CONFIG_JFFS2_DEV "nor0" +#define MTDIDS_DEFAULT "nor0=spi-flash.0" +#define MTDPARTS_DEFAULT \ + "mtdparts=spi-flash.0:" \ + "1m(u-boot)," \ + "7m(kernel)," \ + "-(rootfs)" + +/* Timer */ +#define CONFIG_MCFTMR +#undef CONFIG_MCFPIT + +/* DSPI and Serial Flash */ +#define CONFIG_CF_SPI +#define CONFIG_CF_DSPI +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SERIAL_FLASH +#define CONFIG_HARD_SPI +#define CONFIG_SPI_FLASH_ISSI +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 1 + +#define CONFIG_SYS_SBFHDR_SIZE 0x7 + +#define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ + DSPI_CTAR_PCSSCK_1CLK | \ + DSPI_CTAR_PASC(0) | \ + DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(0) | \ + DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(1) | \ + DSPI_CTAR_BR(6)) +#define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) +#define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 2048/* 2048 KB */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) +#define CONFIG_SYS_MBAR 0xFC000000 + +/* +* Definitions for initial stack pointer and data area (in internal SRAM) +*/ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +/* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) - 32) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) + +/* +* Start addresses for the final memory configuration +* (Set up by the startup code) +* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 +*/ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 128/* SDRAM size in MB */ + +#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) +#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) +#define CONFIG_SYS_DRAM_TEST + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_SERIAL_BOOT +#endif + +#if defined(CONFIG_SERIAL_BOOT ) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +/* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) + +/* +* For booting Linux, the board info and command line data +* have to be in the first 8 MB of memory, since this is +* the maximum mapped by the Linux kernel during initialization ?? +*/ include/configs/stmark2.h line 173
Quoted 10 lines
include/configs/stmark2.h new file +10
-0+/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* Configuration for environment +* Environment is embedded in u-boot in the second sector of the flash +*/ + +#if defined(CONFIG_CF_SBF ) +#define CONFIG_ENV_IS_IN_SPI_FLASH 1This is now in
Kconfig.Quoted 34 lines
include/configs/stmark2.h new file +29
-0+#define CONFIG_ENV_SPI_CS 1 +#define CONFIG_ENV_OFFSET 0x40000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#endif + +#undef CONFIG_ENV_OVERWRITE + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + +#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 12) + +#endif /* __STMARK2_CONFIG_H */ scripts/config_whitelist.txt +0
-0scripts/config_whitelist.txt CONFIG_STM32_GPIO · line 2699
Quoted 4 lines
scripts/config_whitelist.txt +1
-0@@ -2696,6 +2696,7 @@ CONFIG_STM32_GPIO CONFIG_STM32_HSE_HZ CONFIG_STM32_HZ CONFIG_STM32_SERIAL +CONFIG_STMARK2We should stop adding ad-hoc
CONFIG_xxx. Please useKconfig.
Quoted 8 lines
scripts/config_whitelist.txt CONFIG_STM32_GPIO
Quoted 4 lines
scripts/config_whitelist.txt +0
-1CONFIG_STRESS CONFIG_STRIDER CONFIG_STRIDER_CON --Regards,
Bin
Regards,
Angelo Dureghello