Skip to contentSkip to conversation

omap3evm: Update board and defconfig files

PATCH New Derald D. Woods 2 participants 9 messages Aug 3, 2017 – Aug 12, 2017

lore
Share & tools
lore

Derald D. Woods

author
#0 lore raw

PATCH 1/1 omap3evm: Update board and defconfig files

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
---
 board/ti/evm/evm.c          | 126 +++++++++++---
 board/ti/evm/evm.h          |  25 +--
 configs/omap3_evm_defconfig |  67 +++++++-
 include/configs/omap3_evm.h | 390 ++++++++++----------------------------------
 4 files changed, 263 insertions(+), 345 deletions(-)
board/ti/evm/evm.c +101 -25
index fe8e79312f..e770ac04d0 100644
@@ -12,6 +12,8 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #include <common.h>
+#include <dm.h>
+#include <ns16550.h>
 #include <netdev.h>
 #include <asm/io.h>
 #include <asm/arch/mem.h>

@@ -22,14 +24,35 @@
 #include <i2c.h>
 #include <twl4030.h>
 #include <asm/mach-types.h>
+#include <asm/omap_musb.h>
 #include <linux/mtd/nand.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
 #include "evm.h"
 
-#define OMAP3EVM_GPIO_ETH_RST_GEN1		64
-#define OMAP3EVM_GPIO_ETH_RST_GEN2		7
+#ifdef CONFIG_USB_EHCI_HCD
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
+
+#define OMAP3EVM_GPIO_ETH_RST_GEN1 64
+#define OMAP3EVM_GPIO_ETH_RST_GEN2 7
 
 DECLARE_GLOBAL_DATA_PTR;
 
+static const struct ns16550_platdata omap3_evm_serial = {
+	.base = OMAP34XX_UART1,
+	.reg_shift = 2,
+	.clock = V_NS16550_CLK,
+	.fcr = UART_FCR_DEFVAL,
+};
+
+U_BOOT_DEVICE(omap3_evm_uart) = {
+	"ns16550_serial",
+	&omap3_evm_serial
+};
+
 static u32 omap3_evm_version;
 
 u32 get_omap3_evm_rev(void)

@@ -60,25 +83,19 @@ static void omap3_evm_get_revision(void)
 	default:
 		omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
        }
-#else
+#else /* !CONFIG_CMD_NET */
 #if defined(CONFIG_STATIC_BOARD_REV)
-	/*
-	 * Look for static defintion of the board revision
-	 */
+	/* Look for static defintion of the board revision */
 	omap3_evm_version = CONFIG_STATIC_BOARD_REV;
 #else
-	/*
-	 * Fallback to the default above.
-	 */
+	/* Fallback to the default above */
 	omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
-#endif
-#endif	/* CONFIG_CMD_NET */
+#endif /* CONFIG_STATIC_BOARD_REV */
+#endif /* CONFIG_CMD_NET */
 }
 
-#ifdef CONFIG_USB_OMAP3
-/*
- * MUSB port on OMAP3EVM Rev >= E requires extvbus programming.
- */
+#if defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)
+/* MUSB port on OMAP3EVM Rev >= E requires extvbus programming. */
 u8 omap3_evm_need_extvbus(void)
 {
 	u8 retval = 0;

@@ -88,7 +105,7 @@ u8 omap3_evm_need_extvbus(void)
 
 	return retval;
 }
-#endif
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
 
 /*
  * Routine: board_init

@@ -105,7 +122,7 @@ int board_init(void)
 	return 0;
 }
 
-#ifdef CONFIG_SPL_BUILD
+#if defined(CONFIG_SPL_BUILD)
 /*
  * Routine: get_board_mem_timings
  * Description: If we use SPL then there is no x-loader nor config header

@@ -138,7 +155,34 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
 	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 	timings->mr = MICRON_V_MR_165;
 }
-#endif
+#endif /* CONFIG_SPL_BUILD */
+
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+static struct musb_hdrc_config musb_config = {
+	.multipoint     = 1,
+	.dyn_fifo       = 1,
+	.num_eps        = 16,
+	.ram_bits       = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type	= MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_HOST)
+	.mode           = MUSB_HOST,
+#elif defined(CONFIG_USB_MUSB_GADGET)
+	.mode		= MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET"
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
+	.config         = &musb_config,
+	.power          = 100,
+	.platform_ops	= &omap2430_ops,
+	.board_data	= &musb_board_data,
+};
+#endif /* CONFIG_USB_MUSB_OMAP2PLUS */
 
 /*
  * Routine: misc_init_r

@@ -146,8 +190,9 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
  */
 int misc_init_r(void)
 {
+	twl4030_power_init();
 
-#ifdef CONFIG_SYS_I2C_OMAP34XX
+#if defined(CONFIG_SYS_I2C_OMAP34XX)
 	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
 #endif
 

@@ -161,6 +206,13 @@ int misc_init_r(void)
 #endif
 	omap_die_id_display();
 
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+	musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
+	omap_die_id_usbethaddr();
+#endif
 	return 0;
 }
 

@@ -175,7 +227,7 @@ void set_muxconf_regs(void)
 	MUX_EVM();
 }
 
-#ifdef CONFIG_CMD_NET
+#if defined(CONFIG_CMD_NET)
 /*
  * Routine: setup_net_chip
  * Description: Setting up the configuration GPMC registers specific to the

@@ -237,7 +289,7 @@ static void reset_net_chip(void)
 int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
-#ifdef CONFIG_SMC911X
+#if defined(CONFIG_SMC911X)
 #define STR_ENV_ETHADDR	"ethaddr"
 
 	struct eth_device *dev;

@@ -254,7 +306,7 @@ int board_eth_init(bd_t *bis)
 			rc = -1;
 		}
 	}
-#endif
+#endif /* CONFIG_SMC911X */
 	return rc;
 }
 #endif /* CONFIG_CMD_NET */

@@ -264,11 +316,35 @@ int board_mmc_init(bd_t *bis)
 {
 	return omap_mmc_init(0, 0, 0, -1, -1);
 }
-#endif
 
-#if defined(CONFIG_MMC)
 void board_mmc_power_init(void)
 {
 	twl4030_power_mmc_init(0);
 }
-#endif
+#endif /* CONFIG_MMC */
+
+#if defined(CONFIG_USB_EHCI_HCD)
+static struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(int index)
+{
+	return omap_ehci_hcd_stop();
+}
+#endif /* CONFIG_USB_EHCI_HCD */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) && !defined(CONFIG_CMD_NET)
+int board_eth_init(bd_t *bis)
+{
+	return usb_eth_initialize(bis);
+}
+#endif /* CONFIG_USB_ETHER */
board/ti/evm/evm.h +13 -12
index 91e9b88c54..0f8268b33e 100644
@@ -278,12 +278,19 @@ static void reset_net_chip(void);
 								 /* TS_PEN_IRQ */\
 	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | DIS | M4)) /*GPIO_176*/\
 								 /* - LAN_INTR*/\
-	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M0)) /*McSPI1_CS3*/\
-	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0)) /*McSPI2_CLK*/\
-	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0)) /*McSPI2_SIMO*/\
-	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI2_SOMI*/\
-	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS0*/\
-	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS1*/\
+ /* USB EHCI (port 2) */\
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA2*/\
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA7*/\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA4*/\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA5*/\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA6*/\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA3*/\
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DIR*/\
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_NXT*/\
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA0*/\
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA1*/\
  /*Control and debug */\
 	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)) /*SYS_32K*/\
 	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) /*SYS_CLKREQ*/\

@@ -318,12 +325,6 @@ static void reset_net_chip(void);
 	MUX_VAL(CP(ETK_D7_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D7*/\
 	MUX_VAL(CP(ETK_D8_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D8*/\
 	MUX_VAL(CP(ETK_D9_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D9*/\
-	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D10*/\
-	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D11*/\
-	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D12*/\
-	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D13*/\
-	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D14*/\
-	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D15*/\
  /*Die to Die */\
 	MUX_VAL(CP(D2D_MCAD1),		(IEN  | PTD | EN  | M0)) /*d2d_mcad1*/\
 	MUX_VAL(CP(D2D_MCAD2),		(IEN  | PTD | EN  | M0)) /*d2d_mcad2*/\
configs/omap3_evm_defconfig +59 -8

91 lines not on this page · raw message

include/configs/omap3_evm.h +90 -300

439 lines not on this page · raw message

Signature · 1 line
2.13.0
#1 lore raw

PATCH 1/1 omap3evm: Update board and defconfig files

Quoted 4 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
Reviewed-by Tom Rini <[email protected]>

Thanks. Since you have one of these boards, would you like to take over maintainership of it? That means booting it at least once every 2 months, ideally (at least on the final -rc before release, which is pretty consistently scheduled) to catch bugs like this. Thanks again!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170803/9d1536a8/attachment.sig>
author
#2 lore raw

PATCH 1/1 omap3evm: Update board and defconfig files

Quoted 11 lines · Tom Rini
Quoted 4 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
Reviewed-by Tom Rini <[email protected]>

Thanks. Since you have one of these boards, would you like to take over maintainership of it?

​Yes. I do have this board, with the OMAP3530 processor module, and will be able to test releases.

On a side note, I recently posted the following:

http://u-boot.10912.n7.nabble.com/PATCH-arm-omap-Fix-get-device-type-for-OMAP34XX-td300937.html#a300993

I verified the small patch with omap3evm, beagleboard(revc4), and overo. CPU information can be directly read, as it was previously. Is there some consistent road-map for SRAM usage for OMAP34XX specifically?

Derald

Quoted 4 lines

That means booting it at least once every 2
months, ideally (at least on the final -rc before release, which is pretty consistently scheduled) to catch bugs like this. Thanks again!

--

Quoted 2 lines

Tom

​​

#3 lore raw

PATCH 1/1 omap3evm: Update board and defconfig files

Quoted 18 lines · Derald Woods
Quoted 11 lines · Tom Rini
Quoted 4 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
Reviewed-by Tom Rini <[email protected]>

Thanks. Since you have one of these boards, would you like to take over maintainership of it?

​Yes. I do have this board, with the OMAP3530 processor module, and will be able to test releases.

Quoted 7 lines

On a side note, I recently posted the following:

http://u-boot.10912.n7.nabble.com/PATCH-arm-omap-Fix-get-device-type-for-OMAP34XX-td300937.html#a300993

I verified the small patch with omap3evm, beagleboard(revc4), and overo. CPU information can be directly read, as it was previously. Is there some consistent road-map for SRAM usage for OMAP34XX specifically?

Ah yes, I had that on my to reply to list, sorry. What I was wondering was, why does current mainline fail? I had tested that series on the beagleboard xM but indeed not on plain beagleboard.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170803/df9dd2eb/attachment.sig>
author
#4 lore raw

PATCH v2 1/1 omap3evm: Update board and defconfig files

In reply to Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>

---
Changes in v2:
- Unset {EFI,ISO}_PARTITION
- Unset EFI_LOADER
- Unset SPL_EXT_SUPPORT
- Unset THUMB_BUILD
** It does boot with THUMB_BUILD, it just should not be default

---
 board/ti/evm/evm.c          | 126 +++++++++++---
 board/ti/evm/evm.h          |  25 +--
 configs/omap3_evm_defconfig |  70 +++++++-
 include/configs/omap3_evm.h | 390 ++++++++++----------------------------------
 4 files changed, 268 insertions(+), 343 deletions(-)
board/ti/evm/evm.c +101 -25
index fe8e79312f..e770ac04d0 100644
@@ -12,6 +12,8 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #include <common.h>
+#include <dm.h>
+#include <ns16550.h>
 #include <netdev.h>
 #include <asm/io.h>
 #include <asm/arch/mem.h>

@@ -22,14 +24,35 @@
 #include <i2c.h>
 #include <twl4030.h>
 #include <asm/mach-types.h>
+#include <asm/omap_musb.h>
 #include <linux/mtd/nand.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
 #include "evm.h"
 
-#define OMAP3EVM_GPIO_ETH_RST_GEN1		64
-#define OMAP3EVM_GPIO_ETH_RST_GEN2		7
+#ifdef CONFIG_USB_EHCI_HCD
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
+
+#define OMAP3EVM_GPIO_ETH_RST_GEN1 64
+#define OMAP3EVM_GPIO_ETH_RST_GEN2 7
 
 DECLARE_GLOBAL_DATA_PTR;
 
+static const struct ns16550_platdata omap3_evm_serial = {
+	.base = OMAP34XX_UART1,
+	.reg_shift = 2,
+	.clock = V_NS16550_CLK,
+	.fcr = UART_FCR_DEFVAL,
+};
+
+U_BOOT_DEVICE(omap3_evm_uart) = {
+	"ns16550_serial",
+	&omap3_evm_serial
+};
+
 static u32 omap3_evm_version;
 
 u32 get_omap3_evm_rev(void)

@@ -60,25 +83,19 @@ static void omap3_evm_get_revision(void)
 	default:
 		omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
        }
-#else
+#else /* !CONFIG_CMD_NET */
 #if defined(CONFIG_STATIC_BOARD_REV)
-	/*
-	 * Look for static defintion of the board revision
-	 */
+	/* Look for static defintion of the board revision */
 	omap3_evm_version = CONFIG_STATIC_BOARD_REV;
 #else
-	/*
-	 * Fallback to the default above.
-	 */
+	/* Fallback to the default above */
 	omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
-#endif
-#endif	/* CONFIG_CMD_NET */
+#endif /* CONFIG_STATIC_BOARD_REV */
+#endif /* CONFIG_CMD_NET */
 }
 
-#ifdef CONFIG_USB_OMAP3
-/*
- * MUSB port on OMAP3EVM Rev >= E requires extvbus programming.
- */
+#if defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)
+/* MUSB port on OMAP3EVM Rev >= E requires extvbus programming. */
 u8 omap3_evm_need_extvbus(void)
 {
 	u8 retval = 0;

@@ -88,7 +105,7 @@ u8 omap3_evm_need_extvbus(void)
 
 	return retval;
 }
-#endif
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
 
 /*
  * Routine: board_init

@@ -105,7 +122,7 @@ int board_init(void)
 	return 0;
 }
 
-#ifdef CONFIG_SPL_BUILD
+#if defined(CONFIG_SPL_BUILD)
 /*
  * Routine: get_board_mem_timings
  * Description: If we use SPL then there is no x-loader nor config header

@@ -138,7 +155,34 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
 	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
 	timings->mr = MICRON_V_MR_165;
 }
-#endif
+#endif /* CONFIG_SPL_BUILD */
+
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+static struct musb_hdrc_config musb_config = {
+	.multipoint     = 1,
+	.dyn_fifo       = 1,
+	.num_eps        = 16,
+	.ram_bits       = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type	= MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_HOST)
+	.mode           = MUSB_HOST,
+#elif defined(CONFIG_USB_MUSB_GADGET)
+	.mode		= MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET"
+#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
+	.config         = &musb_config,
+	.power          = 100,
+	.platform_ops	= &omap2430_ops,
+	.board_data	= &musb_board_data,
+};
+#endif /* CONFIG_USB_MUSB_OMAP2PLUS */
 
 /*
  * Routine: misc_init_r

@@ -146,8 +190,9 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
  */
 int misc_init_r(void)
 {
+	twl4030_power_init();
 
-#ifdef CONFIG_SYS_I2C_OMAP34XX
+#if defined(CONFIG_SYS_I2C_OMAP34XX)
 	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
 #endif
 

@@ -161,6 +206,13 @@ int misc_init_r(void)
 #endif
 	omap_die_id_display();
 
+#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
+	musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
+	omap_die_id_usbethaddr();
+#endif
 	return 0;
 }
 

@@ -175,7 +227,7 @@ void set_muxconf_regs(void)
 	MUX_EVM();
 }
 
-#ifdef CONFIG_CMD_NET
+#if defined(CONFIG_CMD_NET)
 /*
  * Routine: setup_net_chip
  * Description: Setting up the configuration GPMC registers specific to the

@@ -237,7 +289,7 @@ static void reset_net_chip(void)
 int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
-#ifdef CONFIG_SMC911X
+#if defined(CONFIG_SMC911X)
 #define STR_ENV_ETHADDR	"ethaddr"
 
 	struct eth_device *dev;

@@ -254,7 +306,7 @@ int board_eth_init(bd_t *bis)
 			rc = -1;
 		}
 	}
-#endif
+#endif /* CONFIG_SMC911X */
 	return rc;
 }
 #endif /* CONFIG_CMD_NET */

@@ -264,11 +316,35 @@ int board_mmc_init(bd_t *bis)
 {
 	return omap_mmc_init(0, 0, 0, -1, -1);
 }
-#endif
 
-#if defined(CONFIG_MMC)
 void board_mmc_power_init(void)
 {
 	twl4030_power_mmc_init(0);
 }
-#endif
+#endif /* CONFIG_MMC */
+
+#if defined(CONFIG_USB_EHCI_HCD)
+static struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(int index)
+{
+	return omap_ehci_hcd_stop();
+}
+#endif /* CONFIG_USB_EHCI_HCD */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) && !defined(CONFIG_CMD_NET)
+int board_eth_init(bd_t *bis)
+{
+	return usb_eth_initialize(bis);
+}
+#endif /* CONFIG_USB_ETHER */
board/ti/evm/evm.h +13 -12
index 91e9b88c54..0f8268b33e 100644
@@ -278,12 +278,19 @@ static void reset_net_chip(void);
 								 /* TS_PEN_IRQ */\
 	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | DIS | M4)) /*GPIO_176*/\
 								 /* - LAN_INTR*/\
-	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M0)) /*McSPI1_CS3*/\
-	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0)) /*McSPI2_CLK*/\
-	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0)) /*McSPI2_SIMO*/\
-	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI2_SOMI*/\
-	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS0*/\
-	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS1*/\
+ /* USB EHCI (port 2) */\
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA2*/\
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA7*/\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA4*/\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA5*/\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA6*/\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA3*/\
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DIR*/\
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_NXT*/\
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA0*/\
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA1*/\
  /*Control and debug */\
 	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)) /*SYS_32K*/\
 	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) /*SYS_CLKREQ*/\

@@ -318,12 +325,6 @@ static void reset_net_chip(void);
 	MUX_VAL(CP(ETK_D7_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D7*/\
 	MUX_VAL(CP(ETK_D8_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D8*/\
 	MUX_VAL(CP(ETK_D9_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D9*/\
-	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D10*/\
-	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D11*/\
-	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D12*/\
-	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D13*/\
-	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D14*/\
-	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D15*/\
  /*Die to Die */\
 	MUX_VAL(CP(D2D_MCAD1),		(IEN  | PTD | EN  | M0)) /*d2d_mcad1*/\
 	MUX_VAL(CP(D2D_MCAD2),		(IEN  | PTD | EN  | M0)) /*d2d_mcad2*/\
configs/omap3_evm_defconfig +64 -6

96 lines not on this page · raw message

include/configs/omap3_evm.h +90 -300

439 lines not on this page · raw message

Signature · 1 line
2.13.4
#5 lore raw

PATCH v2 1/1 omap3evm: Update board and defconfig files

Quoted 13 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>

---
Changes in v2:
- Unset {EFI,ISO}_PARTITION
- Unset EFI_LOADER
- Unset SPL_EXT_SUPPORT
- Unset THUMB_BUILD
** It does boot with THUMB_BUILD, it just should not be default

Quoted 6 lines
---
 board/ti/evm/evm.c          | 126 +++++++++++---
 board/ti/evm/evm.h          |  25 +--
 configs/omap3_evm_defconfig |  70 +++++++-
 include/configs/omap3_evm.h | 390 ++++++++++----------------------------------
 4 files changed, 268 insertions(+), 343 deletions(-)

Please update board/ti/evm/MAINTAINERS as well, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170805/2b838f3b/attachment.sig>
author
#6 lore raw

PATCH v3 1/1 omap3: evm: Update board, defconfig, and maintainer file

In reply to Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>

---

Changes in v3:
- Update MAINTAINERS file
- Update commit message

Changes in v2:
- Unset {EFI,ISO}_PARTITION
- Unset EFI_LOADER
- Unset SPL_EXT_SUPPORT
- Unset THUMB_BUILD
** It does boot with THUMB_BUILD, it just should not be default

---
 board/ti/evm/MAINTAINERS    |   2 +-
 board/ti/evm/evm.c          | 126 +++++++++++---
 board/ti/evm/evm.h          |  25 +--
 configs/omap3_evm_defconfig |  70 +++++++-
 include/configs/omap3_evm.h | 390 ++++++++++----------------------------------
 5 files changed, 269 insertions(+), 344 deletions(-)
board/ti/evm/MAINTAINERS +1 -1
index 612a08ace0..cd315c1635 100644
@@ -1,5 +1,5 @@
 EVM BOARD
-M:	Tom Rini <[email protected]>
+M:	Derald D. Woods <[email protected]>
 S:	Maintained
 F:	board/ti/evm/
 F:	include/configs/omap3_evm.h
board/ti/evm/evm.c +101 -25

213 lines not on this page · raw message

board/ti/evm/evm.h +13 -12
index 91e9b88c54..0f8268b33e 100644
@@ -278,12 +278,19 @@ static void reset_net_chip(void);
 								 /* TS_PEN_IRQ */\
 	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | DIS | M4)) /*GPIO_176*/\
 								 /* - LAN_INTR*/\
-	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M0)) /*McSPI1_CS3*/\
-	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M0)) /*McSPI2_CLK*/\
-	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M0)) /*McSPI2_SIMO*/\
-	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M0)) /*McSPI2_SOMI*/\
-	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS0*/\
-	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M0)) /*McSPI2_CS1*/\
+ /* USB EHCI (port 2) */\
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA2*/\
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA7*/\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA4*/\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA5*/\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA6*/\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA3*/\
+	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
+	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DIR*/\
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_NXT*/\
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA0*/\
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)) /*HSUSB2_DATA1*/\
  /*Control and debug */\
 	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)) /*SYS_32K*/\
 	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) /*SYS_CLKREQ*/\

@@ -318,12 +325,6 @@ static void reset_net_chip(void);
 	MUX_VAL(CP(ETK_D7_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D7*/\
 	MUX_VAL(CP(ETK_D8_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D8*/\
 	MUX_VAL(CP(ETK_D9_ES2 ),	(IEN  | PTD | DIS | M0)) /*ETK_D9*/\
-	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D10*/\
-	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D11*/\
-	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D12*/\
-	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D13*/\
-	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D14*/\
-	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M0)) /*ETK_D15*/\
  /*Die to Die */\
 	MUX_VAL(CP(D2D_MCAD1),		(IEN  | PTD | EN  | M0)) /*d2d_mcad1*/\
 	MUX_VAL(CP(D2D_MCAD2),		(IEN  | PTD | EN  | M0)) /*d2d_mcad2*/\
configs/omap3_evm_defconfig +64 -6

96 lines not on this page · raw message

include/configs/omap3_evm.h +90 -300

439 lines not on this page · raw message

Signature · 1 line
2.13.0
#7 lore raw

PATCH v3 1/1 omap3: evm: Update board, defconfig, and maintainer file

Quoted 5 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170806/dff64769/attachment.sig>
#8 lore raw

PATCH v3 1/1 omap3: evm: Update board, defconfig, and maintainer file

In reply to Derald D. Woods
Quoted 5 lines · Derald D. Woods

This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1.

Signed-off-by Derald D. Woods <[email protected]>
Reviewed-by Tom Rini <[email protected]>

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170812/06ed1bca/attachment.sig>