irqchip: qcom: add support for PDC interrupt controller

index d913aec85109..030c7753d45b 100644
@@ -351,4 +351,13 @@ config GOLDFISH_PIC
          Say yes here to enable Goldfish interrupt controller driver used
          for Goldfish based virtual platforms.
 
+config QCOM_PDC
+	bool "QCOM PDC"
+	depends on ARCH_QCOM
+	select IRQ_DOMAIN
+	select IRQ_DOMAIN_HIERARCHY
+	help
+	  Power Domain Controller driver to manage and configure wakeup
+	  IRQs for Qualcomm Technologies Inc (QTI) mobile chips.
+
 endmenu

index d27e3e3619e0..c35ee5345a53 100644
@@ -85,3 +85,4 @@ obj-$(CONFIG_IRQ_UNIPHIER_AIDET)	+= irq-uniphier-aidet.o
 obj-$(CONFIG_ARCH_SYNQUACER)		+= irq-sni-exiu.o
 obj-$(CONFIG_MESON_IRQ_GPIO)		+= irq-meson-gpio.o
 obj-$(CONFIG_GOLDFISH_PIC) 		+= irq-goldfish-pic.o
+obj-$(CONFIG_QCOM_PDC)			+= qcom-pdc.o

new file mode 100644
index 000000000000..0b2c97ddb520
@@ -0,0 +1,78 @@
+PDC interrupt controller
+
+Qualcomm Technologies Inc. SoCs based on the RPM Hardened architecture have a
+Power Domain Controller (PDC) that is on always-on domain. In addition to
+providing power control for the power domains, the hardware also has an
+interrupt controller that can be used to help detect edge low interrupts as
+well detect interrupts when the GIC is non-operational.
+
+GIC is parent interrupt controller at the highest level. Platform interrupt
+controller PDC is next in hierarchy, followed by others. Drivers requiring
+wakeup capabilities of their device interrupts routed through the PDC, must
+specify PDC as their interrupt controller and request the PDC port associated
+with the GIC interrupt. See example below.
+
+Properties:
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: Should contain "qcom,<soc>-pdc"
+		    - "qcom,sdm845-pdc": For SDM845
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Specifies the base physical address for PDC hardware.
+
+- interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Specifies the number of cells needed to encode an interrupt
+		    source.
+		    Must be 2.
+		    The first element of the tuple is the PDC pin for the
+		    interrupt.
+		    The second element is the trigger type.
+
+- interrupt-parent:
+	Usage: required
+	Value type: <phandle>
+	Definition: Specifies the interrupt parent necessary for hierarchical
+		    domain to operate.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <bool>
+	Definition: Identifies the node as an interrupt controller.
+
+- qcom,pdc-ranges:
+	Usage: required
+	Value type: <u32 array>
+	Definition: Specifies the PDC pin offset and the number of PDC ports.
+		    The tuples indicates the valid mapping of valid PDC ports
+		    and their hwirq mapping.
+		    The first element of the tuple is the starting PDC port.
+		    The second element is the GIC hwirq number for the PDC port.
+		    The third element is the number of interrupts in sequence.
+
+Example:
+
+	pdc: interrupt-controller@b220000 {
+		compatible = "qcom,sdm845-pdc";
+		reg = <0xb220000 0x30000>;
+		qcom,pdc-ranges = <0 512 94>, <94 641 15>, <115 662 7>;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&intc>;
+		interrupt-controller;
+	};
+
+DT binding of a device that wants to use the GIC SPI 514 as a wakeup
+interrupt, must do -
+
+	wake-device {
+		interrupts-extended = <&pdc 2 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+In this case interrupt 514 would be mapped to port 2 on the PDC as defined by
+the qcom,pdc-ranges property.