drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
Subsystems (2)
PATCH 1/5 drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
i915_gem_obj_pin_to_display() calls frontbuffer_flush with origin set to DIRTYFB. The callers however are at a vantage point to decide if hardware frontbuffer tracking can do the flush for us. For example, legacy cursor updates, like flips, write to MMIO registers, which then triggers PSR flush by the hardware. Moving frontbuffer_flush out will enable us to skip a software initiated flush by setting origin to FLIP. Thanks to Chris for the idea.
--- drivers/gpu/drm/i915/i915_gem.c | 9 ++++----- drivers/gpu/drm/i915/intel_display.c | 13 ++++++++++--- drivers/gpu/drm/i915/intel_fbdev.c | 6 +++--- drivers/gpu/drm/i915/intel_overlay.c | 1 + 4 files changed, 18 insertions(+), 11 deletions(-)
drivers/gpu/drm/i915/i915_gem.c +4 -5
@@ -4071,9 +4071,10 @@ int i915_gem_set_caching_ioctl(struct drm_device *dev, void *data, }/* -* Prepare buffer for display plane (scanout, cursors, etc). -* Can be called from an uninterruptible phase (modesetting) and allows -* any flushes to be pipelined (for pageflips). +* Prepare buffer for display plane (scanout, cursors, etc). Can be called from +* an uninterruptible phase (modesetting) and allows any flushes to be pipelined +* (for pageflips). We only flush the caches while preparing the buffer for +* display, the callers are responsible for frontbuffer flush. */ struct i915_vma * i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj,
@@ -4139,9 +4140,7 @@ i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj, vma->display_alignment =max_t (u64, vma->display_alignment, alignment); -/* Treat this as an end-of-frame, like intel_user_framebuffer_dirty() */ __i915_gem_object_flush_for_display (obj); -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );/* It should now be out of any other write domains, and we can update * the domain values for our changes.
drivers/gpu/drm/i915/intel_display.c +10 -3
@@ -2806,10 +2806,15 @@ intel_find_initial_plane_obj(struct intel_crtc *intel_crtc,return ; valid_fb: + obj =intel_fb_obj (fb);mutex_lock (&dev->struct_mutex); intel_state->vma =intel_pin_and_fence_fb_obj (fb, primary->state->rotation); + +if (!IS_ERR (intel_state->vma)) +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );mutex_unlock (&dev->struct_mutex); +if (IS_ERR (intel_state->vma)) {DRM_ERROR ("failed to pin boot fb on pipe %d: %li\n" , intel_crtc->pipe,PTR_ERR (intel_state->vma));
@@ -2832,7 +2837,6 @@ intel_find_initial_plane_obj(struct intel_crtc *intel_crtc, intel_state->base.src =drm_plane_state_src (plane_state); intel_state->base.dst =drm_plane_state_dest (plane_state); - obj =intel_fb_obj (fb);if (i915_gem_object_is_tiled (obj)) dev_priv->preserve_bios_swizzle = true;
@@ -12713,10 +12717,12 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) +if (!IS_ERR (vma)) {to_intel_plane_state (new_state)->vma = vma; -else +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); + }else { ret =PTR_ERR (vma); + } }i915_gem_object_wait_priority (obj,0 ,I915_PRIORITY_DISPLAY );
@@ -13136,6 +13142,7 @@ intel_legacy_cursor_update(struct drm_plane *plane, goto out_unlock; } +intel_fb_obj_flush (intel_fb_obj (fb),ORIGIN_DIRTYFB );to_intel_plane_state (new_plane_state)->vma = vma; }
drivers/gpu/drm/i915/intel_fbdev.c +3 -3
@@ -204,6 +204,7 @@ static int intelfb_create(struct drm_fb_helper *helper, sizes->fb_height = intel_fb->base.height; } + fb = &ifbdev->fb->base;mutex_lock (&dev->struct_mutex);intel_runtime_pm_get (dev_priv);
@@ -211,11 +212,12 @@ static int intelfb_create(struct drm_fb_helper *helper,* This also validates that any existing fb inherited from the * BIOS is suitable for own access. */ - vma =intel_pin_and_fence_fb_obj (&ifbdev->fb->base,DRM_MODE_ROTATE_0 ); + vma =intel_pin_and_fence_fb_obj (fb,DRM_MODE_ROTATE_0 );if (IS_ERR (vma)) { ret =PTR_ERR (vma); goto out_unlock; } +intel_fb_obj_flush (intel_fb_obj (fb),ORIGIN_DIRTYFB ); info =drm_fb_helper_alloc_fbi (helper);if (IS_ERR (info)) {
@@ -226,8 +228,6 @@ static int intelfb_create(struct drm_fb_helper *helper, info->par = helper; - fb = &ifbdev->fb->base; - ifbdev->helper.fb = fb;strcpy (info->fix.id,"inteldrmfb" );
drivers/gpu/drm/i915/intel_overlay.c +1 -0
@@ -806,6 +806,7 @@ static int intel_overlay_do_put_image(struct intel_overlay *overlay, ret =PTR_ERR (vma); goto out_pin_section; } +intel_fb_obj_flush (new_bo,ORIGIN_DIRTYFB ); ret =i915_vma_put_fence (vma);if (ret)
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/5 drm/i915/psr: Use more PSR HW tracking.
From: Rodrigo Vivi <[email protected]>
So far we are using frontbuffer tracking for everything and ignoring that PSR has a HW capable HW tracking for many modern usages of GPU on Core platforms and newer Atom ones.
One reason for that is that we were trying to keep same infrastructure in place for VLV/CHV than the rest of platforms. But also because when this infrastructure was created the front-buffer-tracking origin wasn't that good and stable how it is today after Paulo reworked it to attend FBC cases.
However this PSR implementation without HW tracking died on gen8LP. And newer platforms are starting to demand more HW tracking specially with PSR2 cases in mind.
By disabling and re-enabling PSR totally every time we believe someone is going to change the front buffer content we don't allow PSR HW tracking to do this job and specially compromising the whole idea of PSR2 case where the HW tracking detect only the damaged area and do a partial screen update.
So, from now on, on the platforms that has hw_tracking let's rely more on HW tracking.
This also is the case in used by other drivers and more validated by SV teams. So I hope that this will lead us to less misterious bugs.
v2: Only do this for platform that actually has hw tracking.
v3 from DK
Do this only for flips, small gradual changes are better.
--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 3 ++- drivers/gpu/drm/i915/intel_frontbuffer.c | 2 +- drivers/gpu/drm/i915/intel_psr.c | 10 +++++++++- 4 files changed, 13 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +1 -0
@@ -770,6 +770,7 @@ struct i915_psr {bool y_cord_support;bool colorimetry_support;bool alpm; +bool has_hw_tracking;void (*enable_source)(struct intel_dp *,const struct intel_crtc_state *);
drivers/gpu/drm/i915/intel_drv.h +2 -1
@@ -1862,7 +1862,8 @@ void intel_psr_enable(struct intel_dp *intel_dp,void intel_psr_disable (struct intel_dp *intel_dp,const struct intel_crtc_state *old_crtc_state);void intel_psr_invalidate (struct drm_i915_private *dev_priv, -unsigned frontbuffer_bits); +unsigned frontbuffer_bits, +enum fb_op_origin origin);void intel_psr_flush (struct drm_i915_private *dev_priv,unsigned frontbuffer_bits,enum fb_op_origin origin);
drivers/gpu/drm/i915/intel_frontbuffer.c +1 -1
@@ -79,7 +79,7 @@ void __intel_fb_obj_invalidate(struct drm_i915_gem_object *obj,spin_unlock (&dev_priv->fb_tracking.lock); } -intel_psr_invalidate (dev_priv, frontbuffer_bits); +intel_psr_invalidate (dev_priv, frontbuffer_bits, origin);intel_edp_drrs_invalidate (dev_priv, frontbuffer_bits);intel_fbc_invalidate (dev_priv, frontbuffer_bits, origin); }
drivers/gpu/drm/i915/intel_psr.c +9 -1
@@ -824,6 +824,7 @@ void intel_psr_single_frame_update(struct drm_i915_private *dev_priv,* intel_psr_invalidate - Invalidade PSR * @dev_priv: i915 device * @frontbuffer_bits: frontbuffer plane tracking bits +* @origin: which operation caused the invalidate * * Since the hardware frontbuffer tracking has gaps we need to integrate * with the software frontbuffer tracking. This function gets called every
@@ -833,7 +834,7 @@ void intel_psr_single_frame_update(struct drm_i915_private *dev_priv,* Dirty frontbuffers relevant to PSR are tracked in busy_frontbuffer_bits." */ void intel_psr_invalidate (struct drm_i915_private *dev_priv, -unsigned frontbuffer_bits) +unsigned frontbuffer_bits,enum fb_op_origin origin) {struct drm_crtc *crtc;enum pipe pipe;
@@ -841,6 +842,9 @@ void intel_psr_invalidate(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ; +if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +mutex_lock (&dev_priv->psr.lock);if (!dev_priv->psr.enabled) {mutex_unlock (&dev_priv->psr.lock);
@@ -881,6 +885,9 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ; +if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +mutex_lock (&dev_priv->psr.lock);if (!dev_priv->psr.enabled) {mutex_unlock (&dev_priv->psr.lock);
@@ -957,6 +964,7 @@ void intel_psr_init(struct drm_i915_private *dev_priv) dev_priv->psr.activate = vlv_psr_activate; dev_priv->psr.setup_vsc = vlv_psr_setup_vsc; }else { + dev_priv->psr.has_hw_tracking = true; dev_priv->psr.enable_source = hsw_psr_enable_source; dev_priv->psr.disable_source = hsw_psr_disable; dev_priv->psr.enable_sink = hsw_psr_enable_sink;
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/5] drm/i915/psr: Use more PSR HW tracking.
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:19)
Quoted 51 lines
From: Rodrigo Vivi <[email protected]>
So far we are using frontbuffer tracking for everything and ignoring that PSR has a HW capable HW tracking for many modern usages of GPU on Core platforms and newer Atom ones.
One reason for that is that we were trying to keep same infrastructure in place for VLV/CHV than the rest of platforms. But also because when this infrastructure was created the front-buffer-tracking origin wasn't that good and stable how it is today after Paulo reworked it to attend FBC cases.
However this PSR implementation without HW tracking died on gen8LP. And newer platforms are starting to demand more HW tracking specially with PSR2 cases in mind.
By disabling and re-enabling PSR totally every time we believe someone is going to change the front buffer content we don't allow PSR HW tracking to do this job and specially compromising the whole idea of PSR2 case where the HW tracking detect only the damaged area and do a partial screen update.
So, from now on, on the platforms that has
hw_trackinglet's rely more on HW tracking.This also is the case in used by other drivers and more validated by SV teams. So I hope that this will lead us to less misterious bugs.
v2: Only do this for platform that actually has hw tracking.
v3 from DK
Do this only for flips, small gradual changes are better.Cc Dhinakaran Pandiyan <[email protected]>Cc Jim Bride <[email protected]>Cc Vathsala Nagaraju <[email protected]>Signed-off-by Rodrigo Vivi <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 3 ++- drivers/gpu/drm/i915/intel_frontbuffer.c | 2 +- drivers/gpu/drm/i915/intel_psr.c | 10 +++++++++- 4 files changed, 13 insertions(+), 3 deletions(-)drivers/gpu/drm/i915/i915_drv.h +0
-0
drivers/gpu/drm/i915/i915_drv.h struct i915_psr { · line 773
Quoted 4 lines
drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -770,6 +770,7 @@ struct i915_psr {bool y_cord_support;bool colorimetry_support;bool alpm; +bool has_hw_tracking;
Time for some bool:1 compaction?
Quoted 11 lines
drivers/gpu/drm/i915/i915_drv.h +3
-0@@ -841,6 +842,9 @@ void intel_psr_invalidate(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ; +if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +mutex_lock (&dev_priv->psr.lock);if (!dev_priv->psr.enabled) {mutex_unlock (&dev_priv->psr.lock);
drivers/gpu/drm/i915/i915_drv.h void intel_psr_flush(struct drm_i915_private *dev_priv, · line 890
Quoted 6 lines
drivers/gpu/drm/i915/i915_drv.h +3
-0@@ -881,6 +885,9 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ; +if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +
Much easier for the causal reader to understand :) -Chris
_______________________________________________
Intel-gfx mailing list [email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/5] drm/i915/psr: Use more PSR HW tracking.
Quoted 47 lines · Chris Wilson
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:19)
Quoted 46 lines
From: Rodrigo Vivi <[email protected]>
So far we are using frontbuffer tracking for everything and ignoring that PSR has a HW capable HW tracking for many modern usages of GPU on Core platforms and newer Atom ones.
One reason for that is that we were trying to keep same infrastructure in place for VLV/CHV than the rest of platforms. But also because when this infrastructure was created the front-buffer-tracking origin wasn't that good and stable how it is today after Paulo reworked it to attend FBC cases.
However this PSR implementation without HW tracking died on gen8LP. And newer platforms are starting to demand more HW tracking specially with PSR2 cases in mind.
By disabling and re-enabling PSR totally every time we believe someone is going to change the front buffer content we don't allow PSR HW tracking to do this job and specially compromising the whole idea of PSR2 case where the HW tracking detect only the damaged area and do a partial screen update.
So, from now on, on the platforms that has
hw_trackinglet's rely more on HW tracking.This also is the case in used by other drivers and more validated by SV teams. So I hope that this will lead us to less misterious bugs.
v2: Only do this for platform that actually has hw tracking.
v3 from DK
Do this only for flips, small gradual changes are better.Cc Dhinakaran Pandiyan <[email protected]>Cc Jim Bride <[email protected]>Cc Vathsala Nagaraju <[email protected]>Signed-off-by Rodrigo Vivi <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 3 ++- drivers/gpu/drm/i915/intel_frontbuffer.c | 2 +- drivers/gpu/drm/i915/intel_psr.c | 10 +++++++++- 4 files changed, 13 insertions(+), 3 deletions(-)
Quoted 11 lines
drivers/gpu/drm/i915/i915_drv.h struct i915_psr { · line 773
Quoted 9 lines
drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -770,6 +770,7 @@ struct i915_psr {bool y_cord_support;bool colorimetry_support;bool alpm; +bool has_hw_tracking;Time for some bool:1 compaction?
Oddly it increases the binary size, so I didn't make this change in the new version I sent out -
https://patchwork.freedesktop.org/series/39502/
I also left out
Patch 5/5: The mod_timer patch that Andy sent avoids the problem this patch works around.
Patch 4/5: frontbuffer flush during prepare_fb() might be necessary to exit PSR early (before we start updating pipe registers)
Quoted 15 lines
Quoted 15 lines
drivers/gpu/drm/i915/i915_drv.h +3
-0@@ -841,6 +842,9 @@ void intel_psr_invalidate(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ; +if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +mutex_lock (&dev_priv->psr.lock);if (!dev_priv->psr.enabled) {mutex_unlock (&dev_priv->psr.lock);@@ -881,6 +885,9 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,if (!CAN_PSR (dev_priv))return ;
Quoted 10 lines
drivers/gpu/drm/i915/i915_drv.h void intel_psr_flush(struct drm_i915_private *dev_priv, · line 890
Quoted 3 lines
drivers/gpu/drm/i915/i915_drv.h +3
-0+if (dev_priv->psr.has_hw_tracking && origin ==ORIGIN_FLIP ) +return ; +Much easier for the causal reader to understand :) -Chris
_______________________________________________
Intel-gfx mailing list [email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/5 drm/i915/frontbuffer: HW tracking for cursor moves to fix PSR lags.
In reply to Dhinakaran PandiyanDRM_IOCTL_MODE_CURSOR results in frontbuffer flush before the cursor plane MMIOs are written to. But this flush should not be necessary for PSR as hardware tracking triggers PSR exit when MMIOs are written. As for FBC, the spec says "Flips or changes to plane size and panning" cause FBC to be nuked. /sys/kernel/debug/dri/0/i915_fbc_status shows "Compressing: yes" when I move the cursor around.
v3: Use ORIGIN_FLIP now that pin_to_display does not flush frontbuffer.
v2: Update comment in i915_gem_object_pin_to_display_plane. (Chris)
--- drivers/gpu/drm/i915/intel_display.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_display.c +1 -1
@@ -13142,7 +13142,7 @@ intel_legacy_cursor_update(struct drm_plane *plane, goto out_unlock; } -intel_fb_obj_flush (intel_fb_obj (fb),ORIGIN_DIRTYFB ); +intel_fb_obj_flush (intel_fb_obj (fb),ORIGIN_FLIP );to_intel_plane_state (new_plane_state)->vma = vma; }
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/5 drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
In reply to Dhinakaran PandiyanPreparing a framebuffer should not require a flush. _post_plane_update() takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.
--- drivers/gpu/drm/i915/intel_display.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_display.c +2 -4
@@ -12717,12 +12717,10 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) { +if (!IS_ERR (vma))to_intel_plane_state (new_state)->vma = vma; -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); - }else { +else ret =PTR_ERR (vma); - } }i915_gem_object_wait_priority (obj,0 ,I915_PRIORITY_DISPLAY );
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.
Makes sense.
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>
Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-Chris
Quoted 26 lines
--- drivers/gpu/drm/i915/intel_display.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/intel_display.c +2
-4@@ -12717,12 +12717,10 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) { +if (!IS_ERR (vma))to_intel_plane_state (new_state)->vma = vma; -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); - }else { +else ret =PTR_ERR (vma); - } }i915_gem_object_wait_priority (obj,0 ,I915_PRIORITY_DISPLAY );Signature · 1 line
2.14.1
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 7 lines · Chris Wilson
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 32 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 22 lines
--- drivers/gpu/drm/i915/intel_display.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/intel_display.c +2
-4@@ -12717,12 +12717,10 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) { +if (!IS_ERR (vma))to_intel_plane_state (new_state)->vma = vma; -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); - }else { +else ret =PTR_ERR (vma); - } }
Quoted 8 lines
Quoted 4 lines
drivers/gpu/drm/i915/intel_display.c +0
-0i915_gem_object_wait_priority (obj,0 ,I915_PRIORITY_DISPLAY );Signature · 1 line
2.14.1_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-Chris
Page flips used to do intel_frontbuffer_flip_prepare here, followed by intel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?
Then again, seems like frontbuffer tracking should be done per crtc..
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 14 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 13 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 4 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisPage flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?
I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Then again, seems like frontbuffer tracking should be done per crtc..
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-Chris
Quoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;
So we are good here?
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 48 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
Quoted 7 lines
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;
I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 53 lines · Ville Syrjälä
Quoted 52 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
Quoted 6 lines
Quoted 3 lines
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
I think that's just because we've been lazy and not done it (link off mode). I think even without the link off we'd need to reprogram all planes at least.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Rodrigo Vivi
maintainerRe: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 58 lines · Ville Syrjälä
Quoted 57 lines · Ville Syrjälä
Quoted 55 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;
Quoted 6 lines
Quoted 2 lines
I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
I think that's just because we've been lazy and not done it (link off mode).
I agree with you here. This was probably exactly what was missing. But, how to do this without flickering (blinking?!) the screen?
Quoted 1 line
I think even without the link off we'd need to reprogram all planes at least.
on VLV/CHV or everywhere? and why do you think that?
Quoted 8 lines
Signature · 7 lines
-- Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 64 lines · Rodrigo Vivi
Quoted 63 lines · Ville Syrjälä
Quoted 53 lines · Ville Syrjälä
Quoted 52 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
Quoted 6 lines
Quoted 3 lines
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
Quoted 8 lines
Quoted 1 line
I think that's just because we've been lazy and not done it (link off mode).
I agree with you here. This was probably exactly what was missing. But, how to do this without flickering (blinking?!) the screen?
Quoted 1 line
I think even without the link off we'd need to reprogram all planes at least.
on VLV/CHV or everywhere? and why do you think that?
VLV/CHV. I believe the hw implements PSR by simplty turning off the planes (and pipes+dplls for link off), but it doesn't have any automagic stuff for recovering the original state. It's all up to the driver.
IIRC Rodrigo even confirmed this at some point, or at least he had to trigger a plane update to get something visible on the screen.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Rodrigo Vivi
maintainerRe: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 72 lines · Ville Syrjälä
Quoted 71 lines · Rodrigo Vivi
Quoted 58 lines · Ville Syrjälä
Quoted 57 lines · Ville Syrjälä
Quoted 55 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush.
_post_plane_update()takes care of flushing when a flip is scheduled, this should be sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc Paulo Zanoni <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Chris Wilson <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;Quoted 6 lines
Quoted 2 lines
I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
I think that's just because we've been lazy and not done it (link off mode).
I agree with you here. This was probably exactly what was missing. But, how to do this without flickering (blinking?!) the screen?
Quoted 1 line
I think even without the link off we'd need to reprogram all planes at least.
Quoted 8 lines
Quoted 1 line
on VLV/CHV or everywhere? and why do you think that?
VLV/CHV. I believe the hw implements PSR by simplty turning off the planes (and pipes+dplls for link off), but it doesn't have any automagic stuff for recovering the original state. It's all up to the driver.
IIRC Rodrigo even confirmed this at some point, or at least he had to trigger a plane update to get something visible on the screen.
My memory is terrible. But this makes so much sense and in sync with some vague memory flashes here :)
And probably what blocked me for looking there besides the other bugs on core platforms was my disbelieve that would be possible without seeing any blink of a blank screen when exiting PSR. :/
Quoted 4 lines
Signature · 3 lines
-- Ville Syrjälä Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
Quoted 82 lines · Rodrigo Vivi
Quoted 72 lines · Ville Syrjälä
Quoted 71 lines · Rodrigo Vivi
Quoted 58 lines · Ville Syrjälä
Quoted 57 lines · Ville Syrjälä
Quoted 55 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush. _post_plane_update()
takes care of flushing when a flip is scheduled, this should be
sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc: Paulo Zanoni <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Chris Wilson <[email protected]>
Signed-off-by: Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;Quoted 6 lines
Quoted 2 lines
I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
I think that's just because we've been lazy and not done it (link off mode).
I agree with you here. This was probably exactly what was missing. But, how to do this without flickering (blinking?!) the screen?
Quoted 1 line
I think even without the link off we'd need to reprogram all planes at least.
Quoted 8 lines
Quoted 1 line
on VLV/CHV or everywhere? and why do you think that?
VLV/CHV. I believe the hw implements PSR by simplty turning off the planes (and pipes+dplls for link off), but it doesn't have any automagic stuff for recovering the original state. It's all up to the driver.
IIRC Rodrigo even confirmed this at some point, or at least he had to trigger a plane update to get something visible on the screen.
Quoted 8 lines
My memory is terrible. But this makes so much sense and in sync with some vague memory flashes here :)
And probably what blocked me for looking there besides the other bugs on core platforms was my disbelieve that would be possible without seeing any blink of a blank screen when exiting PSR. :/
We've got a couple of options here -
1) Drop this patch because it breaks VLV/CHV link standby.
2) Keep this patch because VLV/CHV link standby is already broken (no plane programming on exit). Follow this up with reworking PSR on VLV/CHV.
3) Or should this be -
if (VLV() || CHV)
intel_fb_obj_flush(obj, ORIGIN_DIRTYFB);
Quoted 4 lines
Quoted 4 lines
Signature · 3 lines
-- Ville Syrjälä Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/5] drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb()
In reply to Rodrigo ViviQuoted 82 lines · Rodrigo Vivi
Quoted 72 lines · Ville Syrjälä
Quoted 71 lines · Rodrigo Vivi
Quoted 58 lines · Ville Syrjälä
Quoted 57 lines · Ville Syrjälä
Quoted 55 lines · Dhinakaran
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Ville Syrjälä
Quoted 23 lines · Dhinakaran
Quoted 19 lines · Maarten Lankhorst
Op 16-02-18 om 20:27 schreef Pandiyan, Dhinakaran:
Quoted 18 lines · Chris Wilson
Quoted 6 lines
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:21)
Quoted 3 lines
Preparing a framebuffer should not require a flush. _post_plane_update()
takes care of flushing when a flip is scheduled, this should be
sufficient for PSR and FBC.Makes sense.
I also think this might speed up the flips a bit by avoiding flushes.
Quoted 9 lines
Quoted 4 lines
Cc: Paulo Zanoni <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Chris Wilson <[email protected]>
Signed-off-by: Dhinakaran Pandiyan <[email protected]>Also
Cc: Maarten Lankhorst <[email protected]> to validate the flow through atomic.
-ChrisQuoted 5 lines
Quoted 2 lines
Page flips used to do
intel_frontbuffer_flip_preparehere, followed byintel_frontbuffer_flip_complete. I think it would make sense to change the patch to do that?I have no context why it was removed, I'll have to understand that change and get back to you.
Quoted 6 lines
Since we supposedly have hw nuke for both fbc and psr there doesn't seem to be much need to do anything for flips. I guess DRRS is the only thing that kinda needs it (not really, just avoids flipping with the slow timings). But I think DRRS should really be tied into the vblank stuff somehow so that we switch to the fast timings whenever a vblank interrupts are enabled.
Quoted 6 lines
Oh, I guess VLV/CHV PSR is what would need this. To do that properly (ie. main link off) I think we'd basically need to do a full modeset when exiting PSR, so it should probably handled somewhere higher up during modeset, and for other uses the frontbuffer tracking should perhaps just schedule a work to do the full modeset.
The mention of "full modeset" got me thinking. I believe you said full modeset because the link needs to be trained on PSR exit if it was off. But, link off isn't supported on VLV/CHV
else if (
IS_VALLEYVIEW(dev_priv)||IS_CHERRYVIEW(dev_priv))/* On VLV and CHV only standby mode is supported. */ dev_priv->psr.link_standby = true;Quoted 6 lines
Quoted 2 lines
I think that's just because we've been lazy and done it. I think even with the link off we'd need to reprogram all planes at least.
Not had coffee yet today, and it shows. Let me rewrite that entire thing:
I think that's just because we've been lazy and not done it (link off mode).
I agree with you here. This was probably exactly what was missing. But, how to do this without flickering (blinking?!) the screen?
Quoted 1 line
I think even without the link off we'd need to reprogram all planes at least.
Quoted 8 lines
Quoted 1 line
on VLV/CHV or everywhere? and why do you think that?
VLV/CHV. I believe the hw implements PSR by simplty turning off the planes (and pipes+dplls for link off), but it doesn't have any automagic stuff for recovering the original state. It's all up to the driver.
IIRC Rodrigo even confirmed this at some point, or at least he had to trigger a plane update to get something visible on the screen.
Quoted 7 lines
My memory is terrible. But this makes so much sense and in sync with some vague memory flashes here :)
And probably what blocked me for looking there besides the other bugs on core platforms was my disbelieve that would be possible without seeing any blink of a blank screen when exiting PSR. :/
I suppose we should start the pipe/planes back up, and only then we can tell the sink to stop using the old stored frame.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 5/5 drm/i915/psr: Wait for PSR transition to complete before exiting.
In reply to Dhinakaran PandiyanWith fbdev, screen freezes after a few continuous PSR exit->enter cycles. Printing out the PSR status register clearly showed this freeze coincided with exiting when the hardware is in a transitory state. So wait for a max of 100 ms (~6 frames) for PSR to become active and then exit.
--- drivers/gpu/drm/i915/intel_psr.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
drivers/gpu/drm/i915/intel_psr.c +11 -0
@@ -738,6 +738,17 @@ static void intel_psr_exit(struct drm_i915_private *dev_priv)WARN_ON (!(val &EDP_PSR2_ENABLE ));I915_WRITE (EDP_PSR2_CTL , val & ~EDP_PSR2_ENABLE ); }else { +/* Wait for about 6 frames in case we just enabled PSR, +* this prevents the screen from freezing as the HW does +* not seem to be able to back off cleanly it is already +* trying to enter PSR. +*/ +intel_wait_for_register (dev_priv, +EDP_PSR_STATUS , +EDP_PSR_STATUS_STATE_MASK , +EDP_PSR_STATUS_STATE_SRDENT , +100 ); + val =I915_READ (EDP_PSR_CTL );WARN_ON (!(val &EDP_PSR_ENABLE ));I915_WRITE (EDP_PSR_CTL , val & ~EDP_PSR_ENABLE );
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/5] drm/i915/psr: Wait for PSR transition to complete before exiting.
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:22)
Quoted 19 lines
With fbdev, screen freezes after a few continuous PSR
exit->entercycles. Printing out the PSR status register clearly showed this freeze coincided with exiting when the hardware is in a transitory state. So wait for a max of 100 ms (~6 frames) for PSR to become active and then exit.Cc Rodrigo Vivi <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 11 +++++++++++ 1 file changed, 11 insertions(+)drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -738,6 +738,17 @@ static void intel_psr_exit(struct drm_i915_private *dev_priv)WARN_ON (!(val &EDP_PSR2_ENABLE ));I915_WRITE (EDP_PSR2_CTL , val & ~EDP_PSR2_ENABLE ); }else {
drivers/gpu/drm/i915/intel_psr.c static void intel_psr_exit(struct drm_i915_private *dev_priv) · line 750
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+/* Wait for about 6 frames in case we just enabled PSR, +* this prevents the screen from freezing as the HW does +* not seem to be able to back off cleanly it is already +* trying to enter PSR. +*/ +intel_wait_for_register (dev_priv, +EDP_PSR_STATUS , +EDP_PSR_STATUS_STATE_MASK , +EDP_PSR_STATUS_STATE_SRDENT , +100 );
I'm going to suggest that you want a DRM_DEBUG_KMS() (_DRIVER? Not sure what works best for PSR/frontbuffer-tracking) at least for spotting trouble when it times out. I would start with a DRM_ERROR for a few CI passes just to see what's happening on our machines before toning it down for production.
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/5] drm/i915/psr: Wait for PSR transition to complete before exiting.
Quoted 28 lines · Chris Wilson
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:22)
Quoted 27 lines
With fbdev, screen freezes after a few continuous PSR
exit->entercycles. Printing out the PSR status register clearly showed this freeze coincided with exiting when the hardware is in a transitory state. So wait for a max of 100 ms (~6 frames) for PSR to become active and then exit.Cc Rodrigo Vivi <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 11 +++++++++++ 1 file changed, 11 insertions(+)drivers/gpu/drm/i915/intel_psr.c +8
-0@@ -738,6 +738,17 @@ static void intel_psr_exit(struct drm_i915_private *dev_priv)WARN_ON (!(val &EDP_PSR2_ENABLE ));I915_WRITE (EDP_PSR2_CTL , val & ~EDP_PSR2_ENABLE ); }else { +/* Wait for about 6 frames in case we just enabled PSR, +* this prevents the screen from freezing as the HW does +* not seem to be able to back off cleanly it is already +* trying to enter PSR. +*/ + intel_wait_for_register(dev_priv, + EDP_PSR_STATUS, + EDP_PSR_STATUS_STATE_MASK,
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c static void intel_psr_exit(struct drm_i915_private *dev_priv) · line 750
Quoted 2 lines
drivers/gpu/drm/i915/intel_psr.c +2
-0+EDP_PSR_STATUS_STATE_SRDENT , + 100);I'm going to suggest that you want a
DRM_DEBUG_KMS()(_DRIVER? Not sure what works best for PSR/frontbuffer-tracking) at least for spotting trouble when it times out. I would start with aDRM_ERRORfor a few CI passes just to see what's happening on our machines before toning it down for production.
Thanks for the suggestion, makes sense. I don't think we have a test to emulate a blinking fbcon cursor, which happens to trigger continuous PSR flushes. I'll look into it.
-DK
Quoted 5 lines
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.CHECKPATCH: warning for series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
In reply to Dhinakaran Pandiyan== Series Details ==
== Series Details ==
Series: series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
URL : https://patchwork.freedesktop.org/series/38410/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip 28b7f4f93d2f drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display 8721f68002db drm/i915/psr: Use more PSR HW tracking. -:65: WARNING: Prefer 'unsigned int' to bare use of 'unsigned' #65: FILE: drivers/gpu/drm/i915/intel_drv.h:1865: + unsigned frontbuffer_bits,
-:100: WARNING: Prefer 'unsigned int' to bare use of 'unsigned' #100: FILE: drivers/gpu/drm/i915/intel_psr.c:837:
+ unsigned frontbuffer_bits, enum fb_op_origin origin)
total: 0 errors, 2 warnings, 0 checks, 64 lines checked787bd9dab50d drm/i915/frontbuffer: HW tracking for cursor moves to fix PSR lags. 478be48e1ec8 drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb() c1b5cfe64bc4 drm/i915/psr: Wait for PSR transition to complete before exiting.
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
In reply to Dhinakaran Pandiyan== Series Details ==
== Series Details ==
Series: series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
URL : https://patchwork.freedesktop.org/series/38410/
State : success
== Summary ==
Series 38410v1 series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
https://patchwork.freedesktop.org/api/1.0/series/38410/revisions/1/mbox/
Test gem_mmap_gtt:
Subgroup basic-small-bo-tiledx:
pass -> FAIL (fi-gdg-551) fdo#102575
Test prime_vgem:
Subgroup basic-fence-flip:
pass -> FAIL (fi-ilk-650) fdo#104008fdo#102575 https://bugs.freedesktop.org/show_bug.cgi?id=102575
fdo#104008 https://bugs.freedesktop.org/show_bug.cgi?id=104008
fi-bdw-5557u total:288 pass:267 dwarn:0 dfail:0 fail:0 skip:21 time:425s fi-bdw-gvtdvm total:288 pass:264 dwarn:0 dfail:0 fail:0 skip:24 time:429s fi-blb-e6850 total:288 pass:223 dwarn:1 dfail:0 fail:0 skip:64 time:376s fi-bsw-n3050 total:288 pass:242 dwarn:0 dfail:0 fail:0 skip:46 time:497s fi-bwr-2160 total:288 pass:183 dwarn:0 dfail:0 fail:0 skip:105 time:289s fi-bxt-dsi total:288 pass:258 dwarn:0 dfail:0 fail:0 skip:30 time:483s fi-bxt-j4205 total:288 pass:259 dwarn:0 dfail:0 fail:0 skip:29 time:490s fi-byt-j1900 total:288 pass:253 dwarn:0 dfail:0 fail:0 skip:35 time:475s fi-byt-n2820 total:288 pass:249 dwarn:0 dfail:0 fail:0 skip:39 time:463s fi-cfl-s2 total:288 pass:262 dwarn:0 dfail:0 fail:0 skip:26 time:569s fi-cnl-y3 total:288 pass:262 dwarn:0 dfail:0 fail:0 skip:26 time:581s fi-elk-e7500 total:288 pass:229 dwarn:0 dfail:0 fail:0 skip:59 time:419s fi-gdg-551 total:288 pass:179 dwarn:0 dfail:0 fail:1 skip:108 time:283s fi-glk-1 total:288 pass:260 dwarn:0 dfail:0 fail:0 skip:28 time:519s fi-hsw-4770 total:288 pass:261 dwarn:0 dfail:0 fail:0 skip:27 time:393s fi-ilk-650 total:288 pass:227 dwarn:0 dfail:0 fail:1 skip:60 time:417s fi-ivb-3520m total:288 pass:259 dwarn:0 dfail:0 fail:0 skip:29 time:463s fi-kbl-7500u total:288 pass:263 dwarn:1 dfail:0 fail:0 skip:24 time:460s fi-kbl-7560u total:288 pass:269 dwarn:0 dfail:0 fail:0 skip:19 time:492s fi-kbl-7567u total:288 pass:268 dwarn:0 dfail:0 fail:0 skip:20 time:454s fi-kbl-r total:288 pass:261 dwarn:0 dfail:0 fail:0 skip:27 time:500s fi-pnv-d510 total:288 pass:222 dwarn:1 dfail:0 fail:0 skip:65 time:593s fi-skl-6260u total:288 pass:268 dwarn:0 dfail:0 fail:0 skip:20 time:433s fi-skl-6600u total:288 pass:261 dwarn:0 dfail:0 fail:0 skip:27 time:508s fi-skl-6700hq total:288 pass:262 dwarn:0 dfail:0 fail:0 skip:26 time:526s fi-skl-6770hq total:288 pass:268 dwarn:0 dfail:0 fail:0 skip:20 time:472s fi-skl-guc total:288 pass:260 dwarn:0 dfail:0 fail:0 skip:28 time:417s fi-skl-gvtdvm total:288 pass:265 dwarn:0 dfail:0 fail:0 skip:23 time:430s fi-snb-2520m total:288 pass:248 dwarn:0 dfail:0 fail:0 skip:40 time:533s fi-snb-2600 total:288 pass:248 dwarn:0 dfail:0 fail:0 skip:40 time:399s
Blacklisted hosts:
fi-glk-dsi total:117 pass:105 dwarn:0 dfail:0 fail:0 skip:12
5b7aaf330f88098deefe45bc69af7908e9db382d drm-tip: 2018y-02m-16d-00h-00m-51s UTC integration manifest c1b5cfe64bc4 drm/i915/psr: Wait for PSR transition to complete before exiting. 478be48e1ec8 drm/i915/frontbuffer: Remove early frontbuffer flush in prepare_plane_fb() 787bd9dab50d drm/i915/frontbuffer: HW tracking for cursor moves to fix PSR lags. 8721f68002db drm/i915/psr: Use more PSR HW tracking.28b7f4f93d2f drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_8054/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:18)
Quoted 52 lines
i915_gem_obj_pin_to_display()callsfrontbuffer_flushwith origin set to DIRTYFB. The callers however are at a vantage point to decide if hardware frontbuffer tracking can do the flush for us. For example, legacy cursor updates, like flips, write to MMIO registers, which then triggers PSR flush by the hardware. Movingfrontbuffer_flushout will enable us to skip a software initiated flush by setting origin to FLIP. Thanks to Chris for the idea.Cc Chris Wilson <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/i915_gem.c | 9 ++++----- drivers/gpu/drm/i915/intel_display.c | 13 ++++++++++--- drivers/gpu/drm/i915/intel_fbdev.c | 6 +++--- drivers/gpu/drm/i915/intel_overlay.c | 1 + 4 files changed, 18 insertions(+), 11 deletions(-)drivers/gpu/drm/i915/i915_gem.c +4
-5@@ -4071,9 +4071,10 @@ int i915_gem_set_caching_ioctl(struct drm_device *dev, void *data, }/* -* Prepare buffer for display plane (scanout, cursors, etc). -* Can be called from an uninterruptible phase (modesetting) and allows -* any flushes to be pipelined (for pageflips). +* Prepare buffer for display plane (scanout, cursors, etc). Can be called from +* an uninterruptible phase (modesetting) and allows any flushes to be pipelined +* (for pageflips). We only flush the caches while preparing the buffer for +* display, the callers are responsible for frontbuffer flush. */ struct i915_vma * i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj,@@ -4139,9 +4140,7 @@ i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj, vma->display_alignment =max_t (u64, vma->display_alignment, alignment); -/* Treat this as an end-of-frame, like intel_user_framebuffer_dirty() */ __i915_gem_object_flush_for_display (obj); -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );/* It should now be out of any other write domains, and we can update * the domain values for our changes. drivers/gpu/drm/i915/intel_display.c +0
-0
drivers/gpu/drm/i915/intel_display.c intel_find_initial_plane_obj(struct intel_crtc *intel_crtc, · line 2815
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +4
-0@@ -2806,10 +2806,15 @@ intel_find_initial_plane_obj(struct intel_crtc *intel_crtc,return ; valid_fb: + obj =intel_fb_obj (fb);mutex_lock (&dev->struct_mutex); intel_state->vma =intel_pin_and_fence_fb_obj (fb, primary->state->rotation); + +if (!IS_ERR (intel_state->vma)) +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );
The fb_obj_flush doesn't need to be inside the lock, so you can do it after the normal error testing (or just do it since the flush doesn't depend on having the vma bound).
Quoted 6 lines
drivers/gpu/drm/i915/intel_display.c +1
-0mutex_unlock (&dev->struct_mutex); +if (IS_ERR (intel_state->vma)) {DRM_ERROR ("failed to pin boot fb on pipe %d: %li\n" , intel_crtc->pipe,PTR_ERR (intel_state->vma));
drivers/gpu/drm/i915/intel_display.c intel_prepare_plane_fb(struct drm_plane *plane, · line 12724
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +3
-2@@ -12713,10 +12717,12 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) +if (!IS_ERR (vma)) {to_intel_plane_state (new_state)->vma = vma; -else +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); + }else { ret =PTR_ERR (vma);
Would
if (IS_ERR(vma)) {
ret = PTR_ERR(vma);
break;
}
intel_fb_obj_flush(obj, ORIGIN_DIRTYFB);
to_intel_plane_state(new_state)->vma = vma;look neater here?
Lgtm,
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 55 lines · Chris Wilson
Quoting Dhinakaran Pandiyan (2018-02-16 04:33:18)
Quoted 54 lines
i915_gem_obj_pin_to_display()callsfrontbuffer_flushwith origin set to DIRTYFB. The callers however are at a vantage point to decide if hardware frontbuffer tracking can do the flush for us. For example, legacy cursor updates, like flips, write to MMIO registers, which then triggers PSR flush by the hardware. Movingfrontbuffer_flushout will enable us to skip a software initiated flush by setting origin to FLIP. Thanks to Chris for the idea.Cc Chris Wilson <[email protected]>Cc Ville Syrjälä <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Dhinakaran Pandiyan <[email protected]>--- drivers/gpu/drm/i915/i915_gem.c | 9 ++++----- drivers/gpu/drm/i915/intel_display.c | 13 ++++++++++--- drivers/gpu/drm/i915/intel_fbdev.c | 6 +++--- drivers/gpu/drm/i915/intel_overlay.c | 1 + 4 files changed, 18 insertions(+), 11 deletions(-)drivers/gpu/drm/i915/i915_gem.c +4
-5@@ -4071,9 +4071,10 @@ int i915_gem_set_caching_ioctl(struct drm_device *dev, void *data, }/* -* Prepare buffer for display plane (scanout, cursors, etc). -* Can be called from an uninterruptible phase (modesetting) and allows -* any flushes to be pipelined (for pageflips). +* Prepare buffer for display plane (scanout, cursors, etc). Can be called from +* an uninterruptible phase (modesetting) and allows any flushes to be pipelined +* (for pageflips). We only flush the caches while preparing the buffer for +* display, the callers are responsible for frontbuffer flush. */ struct i915_vma * i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj,@@ -4139,9 +4140,7 @@ i915_gem_object_pin_to_display_plane(struct drm_i915_gem_object *obj, vma->display_alignment =max_t (u64, vma->display_alignment, alignment); -/* Treat this as an end-of-frame, like intel_user_framebuffer_dirty() */ __i915_gem_object_flush_for_display (obj); -intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );/* It should now be out of any other write domains, and we can update * the domain values for our changes. drivers/gpu/drm/i915/intel_display.c +0
-0@@ -2806,10 +2806,15 @@ intel_find_initial_plane_obj(struct intel_crtc *intel_crtc,return ;
Quoted 12 lines
drivers/gpu/drm/i915/intel_display.c intel_find_initial_plane_obj(struct intel_crtc *intel_crtc, · line 2815
Quoted 8 lines
drivers/gpu/drm/i915/intel_display.c +4
-0valid_fb: + obj =intel_fb_obj (fb);mutex_lock (&dev->struct_mutex); intel_state->vma =intel_pin_and_fence_fb_obj (fb, primary->state->rotation); + +if (!IS_ERR (intel_state->vma)) +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB );The
fb_obj_flushdoesn't need to be inside the lock, so you can do it after the normal error testing (or just do it since the flush doesn't depend on having the vma bound).
Okay, that answers the question I meant to ask. Decided to err on the side of caution.
Quoted 19 lines
Quoted 7 lines
drivers/gpu/drm/i915/intel_display.c +1
-0mutex_unlock (&dev->struct_mutex); +if (IS_ERR (intel_state->vma)) {DRM_ERROR ("failed to pin boot fb on pipe %d: %li\n" , intel_crtc->pipe,PTR_ERR (intel_state->vma));drivers/gpu/drm/i915/intel_display.c intel_prepare_plane_fb(struct drm_plane *plane, · line 12724
Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +3
-2@@ -12713,10 +12717,12 @@ intel_prepare_plane_fb(struct drm_plane *plane,struct i915_vma *vma; vma =intel_pin_and_fence_fb_obj (fb, new_state->rotation); -if (!IS_ERR (vma)) +if (!IS_ERR (vma)) {to_intel_plane_state (new_state)->vma = vma; -else +intel_fb_obj_flush (obj,ORIGIN_DIRTYFB ); + }else { ret =PTR_ERR (vma);Would
Quoted 3 lines
if (IS_ERR(vma)) {
ret = PTR_ERR(vma);
break;There's no loop around this, but this change goes away in [Patch 4/5].
Quoted 5 lines
} intel_fb_obj_flush(obj, ORIGIN_DIRTYFB); to_intel_plane_state(new_state)->vma = vma;
Quoted 8 lines
look neater here?
Lgtm,
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.IGT: success for series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
In reply to Dhinakaran Pandiyan== Series Details ==
== Series Details ==
Series: series starting with [1/5] drm/i915/frontbuffer: Pull frontbuffer_flush out of gem_obj_pin_to_display
URL : https://patchwork.freedesktop.org/series/38410/
State : success
== Summary ==
Test kms_flip:
Subgroup dpms-vs-vblank-race-interruptible:
fail -> PASS (shard-hsw) fdo#103060 +1fdo#103060 https://bugs.freedesktop.org/show_bug.cgi?id=103060
shard-apl total:3397 pass:1767 dwarn:1 dfail:0 fail:20 skip:1608 time:12477s shard-hsw total:3427 pass:1759 dwarn:1 dfail:0 fail:10 skip:1656 time:11764s shard-snb total:3427 pass:1347 dwarn:1 dfail:0 fail:12 skip:2067 time:6690s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_8054/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx