phy: berlin-usb: adjust USB_PHY_RX_CTRL init flags
PATCH 1/1 phy: berlin-usb: adjust USB_PHY_RX_CTRL init flags
Make the value written into the USB_PHY_RX_CTRL configuration register match 0xAA79 value written by manufacturer-supplied kernels for Sony NSZ-GS7 (Berlin2 SoC), Google Chromecast and Valve Steam Link (BG2CD).
This fixes timeouts communicating to the internal hub on Steam Link.
---
Hello,
I'm trying to run mainline kernel on "Steam Link" device built around Marvell BG2CD SoC, and in doing so I've found that USB almost always fails to initialize with timeout errors when connecting to the hub:
[ 0.223563] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.223580] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.223596] usb usb1: Product: EHCI Host Controller [ 0.223608] usb usb1: Manufacturer: Linux 4.15.0-00014-gc6f881cd62dc-dirty ehci_hcd [ 0.223624] usb usb1: SerialNumber: ci_hdrc.0 [ 0.223985] hub 1-0:1.0: USB hub found [ 0.224022] hub 1-0:1.0: 1 port detected [ 0.524726] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 1.044673] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 1.399721] mwifiex_sdio mmc0:0001:1: info: FW download over, size 814048 bytes [ 1.484666] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 2.113451] mwifiex_sdio mmc0:0001:1: WLAN FW is active [ 2.113725] sdio platform data not available [ 2.192570] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p112) [ 2.192599] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p112) [ 2.213433] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.294676] ci_hdrc ci_hdrc.0: port 1 reset error -110
and so on until...
[ 19.254658] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 19.913433] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 19.913472] usb usb1-port1: unable to enumerate USB device
I've inspected how the original kernel performs phy initialization, and found that the value written into the USB_PHY_RX_CTRL register differs in one field. Correcting the field is enough to stabilize it in my case.
I don't know where the _260 choice in mainline source comes from. I've checked three publicly available kernels for devices with this phy, and they all write the same value, 0xAA79.
FWIW, this is not the only difference I've found. Other kernels also:
- do not touch TX config registers;
- drive a particular GPIO low before and high after configuring the phy.
I am unsure if anything needs to or can be done about those differences.
Thanks.
Alexander
drivers/phy/marvell/phy-berlin-usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/phy/marvell/phy-berlin-usb.c +1 -1
@@ -127,7 +127,7 @@ static int phy_berlin_usb_power_on(struct phy *phy)writel (V2I_VCO_RATIO (0x5 ) |R_ROTATE_0 |ANA_TEST_DC_CTRL (0x5 ), priv->base +USB_PHY_ANALOG );writel (PHASE_FREEZE_DLY_4_CL |ACK_LENGTH_16_CL |SQ_LENGTH_12 | -DISCON_THRESHOLD_260 |SQ_THRESHOLD (0xa ) |LPF_COEF (0x2 ) | +DISCON_THRESHOLD_270 |SQ_THRESHOLD (0xa ) |LPF_COEF (0x2 ) |INTPL_CUR_30 , priv->base +USB_PHY_RX_CTRL );writel (TX_VDD12_13 |TX_OUT_AMP (0x3 ), priv->base +USB_PHY_TX_CTRL1 );
Signature · 1 line
2.11.0
Hi Alexander,
I've added Jisheng in Cc so he can have a look at this.
Thanks!
Antoine
Quoted 76 lines · Alexander Monakov
Make the value written into the
USB_PHY_RX_CTRLconfiguration register match0xAA79value written by manufacturer-supplied kernels for Sony NSZ-GS7 (Berlin2 SoC), Google Chromecast and Valve Steam Link (BG2CD).This fixes timeouts communicating to the internal hub on Steam Link.
Cc Kishon Vijay Abraham I <[email protected]>Cc Antoine Tenart <[email protected]>Signed-off-by Alexander Monakov <[email protected]>---
Hello,I'm trying to run mainline kernel on "Steam Link" device built around Marvell BG2CD SoC, and in doing so I've found that USB almost always fails to initialize with timeout errors when connecting to the hub:
[ 0.223563] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.223580] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.223596] usb usb1: Product: EHCI Host Controller [ 0.223608] usb usb1: Manufacturer: Linux 4.15.0-00014-gc6f881cd62dc-dirty ehci_hcd [ 0.223624] usb usb1: SerialNumber: ci_hdrc.0 [ 0.223985] hub 1-0:1.0: USB hub found [ 0.224022] hub 1-0:1.0: 1 port detected [ 0.524726] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 1.044673] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 1.399721] mwifiex_sdio mmc0:0001:1: info: FW download over, size 814048 bytes [ 1.484666] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 2.113451] mwifiex_sdio mmc0:0001:1: WLAN FW is active [ 2.113725] sdio platform data not available [ 2.192570] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p112) [ 2.192599] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p112) [ 2.213433] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.294676] ci_hdrc ci_hdrc.0: port 1 reset error -110and so on until...
[ 19.254658] ci_hdrc ci_hdrc.0: port 1 reset error -110 [ 19.913433] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 19.913472] usb usb1-port1: unable to enumerate USB deviceI've inspected how the original kernel performs phy initialization, and found that the value written into the
USB_PHY_RX_CTRLregister differs in one field. Correcting the field is enough to stabilize it in my case.I don't know where the _260 choice in mainline source comes from. I've checked three publicly available kernels for devices with this phy, and they all write the same value,
0xAA79.FWIW, this is not the only difference I've found. Other kernels also:
- do not touch TX config registers;
- drive a particular GPIO low before and high after configuring the phy.I am unsure if anything needs to or can be done about those differences.
Thanks.
Alexanderdrivers/phy/marvell/phy-berlin-usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/phy/marvell/phy-berlin-usb.c +1
-1@@ -127,7 +127,7 @@ static int phy_berlin_usb_power_on(struct phy *phy)writel (V2I_VCO_RATIO (0x5 ) |R_ROTATE_0 |ANA_TEST_DC_CTRL (0x5 ), priv->base +USB_PHY_ANALOG );writel (PHASE_FREEZE_DLY_4_CL |ACK_LENGTH_16_CL |SQ_LENGTH_12 | -DISCON_THRESHOLD_260 |SQ_THRESHOLD (0xa ) |LPF_COEF (0x2 ) | +DISCON_THRESHOLD_270 |SQ_THRESHOLD (0xa ) |LPF_COEF (0x2 ) |INTPL_CUR_30 , priv->base +USB_PHY_RX_CTRL );writel (TX_VDD12_13 |TX_OUT_AMP (0x3 ), priv->base +USB_PHY_TX_CTRL1 );Signature · 1 line
2.11.0
Signature · 3 lines
Antoine Ténart, Bootlin (formerly Free Electrons) Embedded Linux and Kernel engineering https://bootlin.com