drm/i915/fbdev: Enable late fbdev initial configuration
Subsystems (2)
PATCH 1/1 drm/i915/fbdev: Enable late fbdev initial configuration
If the initial fbdev configuration(intel_fbdev_initial_config()) runs and there still no sink connected it will cause drm_fb_helper_initial_config() to return 0 as no error happened(but internally the return is -EAGAIN).
Because no framebuffer was allocated, when a sink is connected intel_fbdev_output_poll_changed() will not execute drm_fb_helper_hotplug_event() that would trigger another try to do the initial fbdev configuration.
So here creating a dummy framebuffer of 800x600, so drm_fb_helper_hotplug_event() will be executed and fbdev can be properly setup when a sink is connected, if needed the dummy framebuffer will be freed and a new with the proper size will be allocated.
This issue also happens when a MST DP sink is connected since boot, as the MST topology is discovered in parallel if intel_fbdev_initial_config() is executed before the first sink MST is discovered it will cause this same issue.
This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425
--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_fbdev.c +23 -1
@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} +static void intel_fbdev_initial_config (void *data,async_cookie_t cookie) {struct intel_fbdev *ifbdev = data;/* Due to peculiar init order wrt to hpd handling this is separate. */ if (drm_fb_helper_initial_config (&ifbdev->helper, - ifbdev->preferred_bpp)) + ifbdev->preferred_bpp)) {intel_fbdev_unregister (to_i915 (ifbdev->helper.dev)); +return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }void intel_fbdev_initial_config_async (struct drm_device *dev)
Signature · 6 lines
2.17.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for drm/i915/fbdev: Enable late fbdev initial configuration
== Series Details ==
== Series Details ==
Series: drm/i915/fbdev: Enable late fbdev initial configuration
URL : https://patchwork.freedesktop.org/series/41851/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4060 -> Patchwork_8714 =
== Summary - WARNING ==
Minor unknown changes coming with Patchwork_8714 need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_8714, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
External URL: https://patchwork.freedesktop.org/api/1.0/series/41851/revisions/1/mbox/
== Possible new issues ==
Here are the unknown changes that may have been introduced in Patchwork_8714:
=== IGT changes ===
==== Warnings ====
igt@gem_exec_gttfill@basic:
fi-pnv-d510: SKIP -> PASS
igt@kms_force_connector_basic@force-load-detect:
fi-ivb-3520m: PASS -> SKIP +3== Known issues ==
Here are the changes found in Patchwork_8714 that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@gem_exec_suspend@basic-s3:
fi-ivb-3520m: PASS -> DMESG-WARN (fdo#106084)
==== Possible fixes ====
igt@gem_exec_suspend@basic-s4-devices:
fi-ivb-3520m: DMESG-WARN (fdo#106084) -> PASS
igt@kms_pipe_crc_basic@read-crc-pipe-b:
fi-glk-j4005: DMESG-WARN (fdo#106097) -> PASS
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-b:
fi-snb-2520m: INCOMPLETE (fdo#103713) -> PASS
fi-bxt-dsi: INCOMPLETE (fdo#103927) -> PASS fdo#103713 https://bugs.freedesktop.org/show_bug.cgi?id=103713
fdo#103927 https://bugs.freedesktop.org/show_bug.cgi?id=103927
fdo#106084 https://bugs.freedesktop.org/show_bug.cgi?id=106084
fdo#106097 https://bugs.freedesktop.org/show_bug.cgi?id=106097
== Participating hosts (34 -> 32) ==
Additional (1): fi-glk-1
Missing (3): fi-ilk-m540 fi-cnl-y3 fi-skl-6700hq
== Build changes ==
* Linux: CI_DRM_4060 -> Patchwork_8714
CI_DRM_4060: 17148956c3830de3194c17693be76f85f05f692f @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4441: 83ba5b7d3bde48b383df41792fc9c955a5a23bdb @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_8714: 07a7c687e23721dccc869d9c0a4e2b0b1e817396 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4441: e60d247eb359f044caf0c09904da14e39d7adca1 @ git://anongit.freedesktop.org/piglit
== Linux commits ==
07a7c687e237 drm/i915/fbdev: Enable late fbdev initial configuration
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_8714/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 61 lines
If the initial fbdev configuration(intel_fbdev_initial_config()) runs and there still no sink connected it will cause
drm_fb_helper_initial_config()to return 0 as no error happened(but internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to do the initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be properly setup when a sink is connected, if needed the dummy framebuffer will be freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since boot, as the MST topology is discovered in parallel if
intel_fbdev_initial_config()is executed before the first sink MST is discovered it will cause this same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +15
-1@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} +static void intel_fbdev_initial_config (void *data,async_cookie_t cookie) {struct intel_fbdev *ifbdev = data;/* Due to peculiar init order wrt to hpd handling this is separate. */ if (drm_fb_helper_initial_config(&ifbdev->helper, - ifbdev->preferred_bpp))
drivers/gpu/drm/i915/intel_fbdev.c int intel_fbdev_init(struct drm_device *dev) · line 729
Quoted 10 lines
drivers/gpu/drm/i915/intel_fbdev.c +8
-0+ ifbdev->preferred_bpp)) {intel_fbdev_unregister (to_i915 (ifbdev->helper.dev)); +return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }
Did you try
drivers/gpu/drm/i915/intel_fbdev.c +1 -0
@@ -493,6 +493,7 @@ static bool intel_fb_initial_config(struct drm_fb_helper *fb_helper, bail:DRM_DEBUG_KMS ("Not using firmware configuration\n" );memcpy (enabled, save_enabled, count); + fb_helper->deferred_setup = true; ret = false; }
possible as of
commit ca91a2758fcef6635626993557dd51cfbb6dd134
Author: Daniel Vetter <[email protected]> Date: Thu Jul 6 15:00:21 2017 +0200
drm/fb-helper: Support deferred setup
FB helper code falls back to a 1024x768 mode if no outputs are connected or don't report back any modes upon initialization. This can be annoying because outputs that are added to FB helper later on can't be used with FB helper if they don't support a matching mode.
...
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 93 lines · Chris Wilson
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 75 lines
If the initial fbdev configuration(intel_fbdev_initial_config()) runs and
there still no sink connected it will causedrm_fb_helper_initial_config()to return 0 as no error happened(but internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to do the
initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be properly
setup when a sink is connected, if needed the dummy framebuffer will be
freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel ifintel_fbdev_initial_config()
is executed before the first sink MST is discovered it will cause this
same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +15
-0@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} +static void intel_fbdev_initial_config (void *data,async_cookie_t cookie) {struct intel_fbdev *ifbdev = data;/* Due to peculiar init order wrt to hpd handling this is separate. */
if (drm_fb_helper_initial_config(&ifbdev->helper,drivers/gpu/drm/i915/intel_fbdev.c +1
-1- ifbdev->preferred_bpp)) + ifbdev->preferred_bpp)) { intel_fbdev_unregister(to_i915(ifbdev-Quoted 1 line
helper.dev));
drivers/gpu/drm/i915/intel_fbdev.c
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +7
-0+return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }Did you try
drivers/gpu/drm/i915/intel_fbdev.c +0
-0
drivers/gpu/drm/i915/intel_fbdev.c static bool intel_fb_initial_config(struct · line 497
Quoted 5 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-0@@ -493,6 +493,7 @@ static bool intel_fb_initial_config(struct drm_fb_helper *fb_helper, bail: DRM_DEBUG_KMS("Not using firmware configuration\n");memcpy (enabled, save_enabled, count); + fb_helper->deferred_setup = true;
This is too earlier to set deferred_setup when intel_fb_initial_config() fails, __drm_fb_helper_initial_config_and_unlock() will then try to probe/create a fb but as there is no sink connected it will fail too.
Also __drm_fb_helper_initial_config_and_unlock() is already setting deferred_setup if both attempts fails.
Quoted 20 lines
drivers/gpu/drm/i915/intel_fbdev.c +0
-0ret = false; }possible as of
commit
ca91a2758fcef6635626993557dd51cfbb6dd134Author: Daniel Vetter <[email protected]> Date: Thu Jul 6 15:00:21 2017 +0200drm/fb-helper: Support deferred setup
FB helper code falls back to a 1024x768 mode if no outputs are
connected
or don't report back any modes upon initialization. This can be
annoying
because outputs that are added to FB helper later on can't be
used with
FB helper if they don't support a matching mode.
...
Quoted 2 lines
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoting Souza, Jose (2018-04-18 01:07:16)
Quoted 105 lines · Chris Wilson
Quoted 93 lines
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 75 lines
If the initial fbdev configuration(intel_fbdev_initial_config()) runs and
there still no sink connected it will causedrm_fb_helper_initial_config()to return 0 as no error happened(but internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to do the
initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be properly
setup when a sink is connected, if needed the dummy framebuffer will be
freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel ifintel_fbdev_initial_config()
is executed before the first sink MST is discovered it will cause this
same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +15
-0@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} +static void intel_fbdev_initial_config (void *data,async_cookie_t cookie) {struct intel_fbdev *ifbdev = data;/* Due to peculiar init order wrt to hpd handling this is separate. */
if (drm_fb_helper_initial_config(&ifbdev->helper,drivers/gpu/drm/i915/intel_fbdev.c +1
-1- ifbdev->preferred_bpp)) + ifbdev->preferred_bpp)) { intel_fbdev_unregister(to_i915(ifbdev-Quoted 1 line
helper.dev));
drivers/gpu/drm/i915/intel_fbdev.c
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +7
-0+return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }Did you try
drivers/gpu/drm/i915/intel_fbdev.c +0
-0drivers/gpu/drm/i915/intel_fbdev.c static bool intel_fb_initial_config(struct · line 497
Quoted 5 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-0@@ -493,6 +493,7 @@ static bool intel_fb_initial_config(struct drm_fb_helper *fb_helper, bail: DRM_DEBUG_KMS("Not using firmware configuration\n");memcpy (enabled, save_enabled, count); + fb_helper->deferred_setup = true;This is too earlier to set
deferred_setupwhenintel_fb_initial_config()fails,__drm_fb_helper_initial_config_and_unlock()will then try to probe/create a fb but as there is no sink connected it will fail too.
Quoted 2 lines
Also
__drm_fb_helper_initial_config_and_unlock()is already settingdeferred_setupif both attempts fails.
So...
drivers/gpu/drm/i915/intel_fbdev.c +1 -1
@@ -807,7 +807,7 @@ void intel_fbdev_output_poll_changed(struct drm_device *dev)return ;intel_fbdev_sync (ifbdev); -if (ifbdev->vma) +if (ifbdev->vma || ifbdev->helper->deferred_setup)drm_fb_helper_hotplug_event (&ifbdev->helper); }
?
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 131 lines · Chris Wilson
Quoting Souza, Jose (2018-04-18 01:07:16)
Quoted 119 lines · Chris Wilson
Quoted 105 lines
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 87 lines
If the initial fbdev configuration(intel_fbdev_initial_config())
runs and
there still no sink connected it will causedrm_fb_helper_initial_config()to return 0 as no error happened(but
internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to do
the
initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be properly
setup when a sink is connected, if needed the dummy framebuffer will be
freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since boot,
as
the MST topology is discovered in parallel ifintel_fbdev_initial_config()
is executed before the first sink MST is discovered it will cause
this
same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +15
-0@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} + static void intel_fbdev_initial_config(void *data,
async_cookie_t
cookie){ struct intel_fbdev *ifbdev = data; /* Due to peculiar init order wrt to hpd handling this is separate. */ if (drm_fb_helper_initial_config(&ifbdev->helper,- ifbdev-
Quoted 1 line
preferred_bpp))+ ifbdev-
Quoted 1 line
preferred_bpp)) {intel_fbdev_unregister(to_i915(ifbdev-
Quoted 1 line
helper.dev));
drivers/gpu/drm/i915/intel_fbdev.c
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +7
-0+return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }Did you try
drivers/gpu/drm/i915/intel_fbdev.c +0
-0drivers/gpu/drm/i915/intel_fbdev.c static bool intel_fb_initial_config(struct · line 498
Quoted 6 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-0@@ -493,6 +493,7 @@ static bool intel_fb_initial_config(structdrm_fb_helper *fb_helper, bail: DRM_DEBUG_KMS("Not using firmware configuration\n");memcpy (enabled, save_enabled, count); + fb_helper->deferred_setup = true;This is too earlier to set
deferred_setupwhenintel_fb_initial_config()fails,__drm_fb_helper_initial_config_and_unlock()will then try to probe/create a fb but as there is no sink connected it will fail too.Quoted 2 lines
Also
__drm_fb_helper_initial_config_and_unlock()is already settingdeferred_setupif both attempts fails.So...
drivers/gpu/drm/i915/intel_fbdev.c +0
-0
drivers/gpu/drm/i915/intel_fbdev.c void intel_fbdev_output_poll_changed(struct · line 813
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-1@@ -807,7 +807,7 @@ void intel_fbdev_output_poll_changed(struct drm_device *dev) return;intel_fbdev_sync (ifbdev); -if (ifbdev->vma) +if (ifbdev->vma || ifbdev->helper->deferred_setup)drm_fb_helper_hotplug_event (&ifbdev->helper); }
That would work but according to your comment here: https://patchwork.f
reedesktop.org/patch/196089/ that would lead to a crash in some case.
Quoted 3 lines
?
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoting Souza, Jose (2018-04-18 17:42:47)
Quoted 135 lines · Chris Wilson
Quoted 134 lines
Quoting Souza, Jose (2018-04-18 01:07:16)
Quoted 119 lines · Chris Wilson
Quoted 105 lines
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 87 lines
If the initial fbdev configuration(intel_fbdev_initial_config())
runs and
there still no sink connected it will causedrm_fb_helper_initial_config()to return 0 as no error happened(but
internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to do
the
initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be properly
setup when a sink is connected, if needed the dummy framebuffer will be
freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since boot,
as
the MST topology is discovered in parallel ifintel_fbdev_initial_config()
is executed before the first sink MST is discovered it will cause
this
same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +15
-0@@ -696,14 +696,36 @@ int intel_fbdev_init(struct drm_device *dev)return 0 ; } +static void intel_fbdev_dummy_fb_create (struct intel_fbdev *ifbdev) +{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) +DRM_ERROR ("Unable to create dummy framebufer" ); +} + static void intel_fbdev_initial_config(void *data,
async_cookie_t
cookie){ struct intel_fbdev *ifbdev = data; /* Due to peculiar init order wrt to hpd handling this is separate. */ if (drm_fb_helper_initial_config(&ifbdev->helper,- ifbdev-
Quoted 1 line
preferred_bpp))+ ifbdev-
Quoted 1 line
preferred_bpp)) {intel_fbdev_unregister(to_i915(ifbdev-
Quoted 1 line
helper.dev));
drivers/gpu/drm/i915/intel_fbdev.c
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +7
-0+return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }Did you try
drivers/gpu/drm/i915/intel_fbdev.c +0
-0drivers/gpu/drm/i915/intel_fbdev.c static bool intel_fb_initial_config(struct · line 498
Quoted 6 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-0@@ -493,6 +493,7 @@ static bool intel_fb_initial_config(structdrm_fb_helper *fb_helper, bail: DRM_DEBUG_KMS("Not using firmware configuration\n");memcpy (enabled, save_enabled, count); + fb_helper->deferred_setup = true;This is too earlier to set
deferred_setupwhenintel_fb_initial_config()fails,__drm_fb_helper_initial_config_and_unlock()will then try to probe/create a fb but as there is no sink connected it will fail too.Quoted 2 lines
Also
__drm_fb_helper_initial_config_and_unlock()is already settingdeferred_setupif both attempts fails.So...
drivers/gpu/drm/i915/intel_fbdev.c +0
-0@@ -807,7 +807,7 @@ void intel_fbdev_output_poll_changed(struct drm_device *dev) return;
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c void intel_fbdev_output_poll_changed(struct drm_device *dev) · line 812
Quoted 5 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-1intel_fbdev_sync (ifbdev); -if (ifbdev->vma) +if (ifbdev->vma || ifbdev->helper->deferred_setup)drm_fb_helper_hotplug_event (&ifbdev->helper); }That would work but according to your comment here: https://patchwork.f
reedesktop.org/patch/196089/ that would lead to a crash in some case.
In the deferred_setup case, won't it go to intelfb_create() and after that point if we still have no ifdev->vma we won't hit any other pathway?
Just because it's been historically buggy (at least 2 instances now of having to apply protection here), it may have been fixed... Unlikely, but maybe it all finally works.
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 162 lines · Chris Wilson
Quoting Souza, Jose (2018-04-18 17:42:47)
Quoted 150 lines · Chris Wilson
Quoted 149 lines
Quoting Souza, Jose (2018-04-18 01:07:16)
Quoted 133 lines · Chris Wilson
Quoted 121 lines
Quoting José Roberto de Souza (2018-04-17 23:34:18)
Quoted 99 lines
If the initial fbdev configuration(intel_fbdev_initial_config()) runs and
there still no sink connected it will causedrm_fb_helper_initial_config()to return 0 as no error happened(but
internally the return is-EAGAIN).
Because no framebuffer was allocated, when a sink is connectedintel_fbdev_output_poll_changed()will not executedrm_fb_helper_hotplug_event()that would trigger another try to
do
the
initial fbdev configuration.So here creating a dummy framebuffer of 800x600, so
drm_fb_helper_hotplug_event()will be executed and fbdev can be
properly
setup when a sink is connected, if needed the dummy framebuffer
will be
freed and a new with the proper size will be allocated.This issue also happens when a MST DP sink is connected since
boot,
as
the MST topology is discovered in parallel ifintel_fbdev_initial_config()
is executed before the first sink MST is discovered it will cause
this
same issue.This is a follow up patch of
https://patchwork.freedesktop.org/patch/196089/Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=1041
58
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=1044
25Cc Chris Wilson <[email protected]>Cc Rodrigo Vivi <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_fbdev.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_fbdev.c +0
-0@@ -696,14 +696,36 @@ int intel_fbdev_init(struct
drm_device
*dev)return 0;}
+static void
intel_fbdev_dummy_fb_create(struct intel_fbdev *ifbdev)drivers/gpu/drm/i915/intel_fbdev.c +12
-0+{ +struct drm_fb_helper_surface_size sizes; + + sizes.fb_width =800 ; + sizes.fb_height =600 ; + sizes.surface_width = sizes.fb_width; + sizes.surface_height = sizes.fb_height; + sizes.surface_bpp =32 ; + sizes.surface_depth =24 ; + +if (intelfb_create (&ifbdev->helper, &sizes)) + DRM_ERROR("Unable to create dummyframebufer");
drivers/gpu/drm/i915/intel_fbdev.c +2
-0+} + static void intel_fbdev_initial_config(void *data,
async_cookie_t
cookie){ struct intel_fbdev *ifbdev = data; /* Due to peculiar init order wrt to hpd handling this is separate. */ if (drm_fb_helper_initial_config(&ifbdev->helper,- ifbdev-
Quoted 1 line
preferred_bpp))+ ifbdev-
Quoted 1 line
preferred_bpp)) {intel_fbdev_unregister(to_i915(ifbdev-
Quoted 1 line
helper.dev));
drivers/gpu/drm/i915/intel_fbdev.c
Quoted 8 lines
drivers/gpu/drm/i915/intel_fbdev.c +7
-0+return ; + } + +mutex_lock (&ifbdev->helper.lock); +if (!ifbdev->vma) +intel_fbdev_dummy_fb_create (ifbdev); +mutex_unlock (&ifbdev->helper.lock); }Did you try
drivers/gpu/drm/i915/intel_fbdev.c +0
-0@@ -493,6 +493,7 @@ static boolintel_fb_initial_config(struct
drm_fb_helper*fb_helper,
bail:
DRM_DEBUG_KMS("Not using firmwareQuoted 3 lines
configuration\n"); memcpy(enabled, save_enabled, count);+
fb_helper->deferred_setup= true;This is too earlier to set
deferred_setupwhenintel_fb_initial_config()fails,__drm_fb_helper_initial_config_and_unlock()will then try to probe/create a fb but as there is no sink connected it will fail
too.Quoted 3 lines
Also
__drm_fb_helper_initial_config_and_unlock()is already settingdeferred_setupif both attempts fails.So...
drivers/gpu/drm/i915/intel_fbdev.c +0
-0@@ -807,7 +807,7 @@ void intel_fbdev_output_poll_changed(struct drm_device *dev) return;Quoted 10 lines
drivers/gpu/drm/i915/intel_fbdev.c void intel_fbdev_output_poll_changed(struct drm_device *dev) · line 812
Quoted 5 lines
drivers/gpu/drm/i915/intel_fbdev.c +1
-1intel_fbdev_sync (ifbdev); -if (ifbdev->vma) +if (ifbdev->vma || ifbdev->helper->deferred_setup)drm_fb_helper_hotplug_event (&ifbdev->helper); }That would work but according to your comment here: https://patchwo
rk.f
reedesktop.org/patch/196089/ that would lead to a crash in some case.
Quoted 3 lines
In the
deferred_setupcase, won't it go tointelfb_create()and after that point if we still have noifdev->vmawe won't hit any other pathway?
It will, okay I will just run some tests and send it adding you as 'Signed-off-by:' that is okay?
Thanks
Quoted 6 lines
Just because it's been historically buggy (at least 2 instances now of
having to apply protection here), it may have been fixed... Unlikely, but maybe it all finally works.
-Chris
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.BAT: failure for drm/i915/fbdev: Enable late fbdev initial configuration (rev2)
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: drm/i915/fbdev: Enable late fbdev initial configuration (rev2)
URL : https://patchwork.freedesktop.org/series/41851/
State : failure
== Summary ==
Applying: drm/i915/fbdev: Enable late fbdev initial configuration
error: patch failed: drivers/gpu/drm/i915/intel_fbdev.c:493
error: drivers/gpu/drm/i915/intel_fbdev.c: patch does not apply
error: Did you hand edit your patch?
It does not apply to blobs recorded in its index.
Using index info to reconstruct a base tree...
M drivers/gpu/drm/i915/intel_fbdev.c
Patch failed at 0001 drm/i915/fbdev: Enable late fbdev initial configuration The copy of the patch that failed is found in: .git/rebase-apply/patch When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead. To restore the original branch and stop patching, run "git am --abort".
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.IGT: success for drm/i915/fbdev: Enable late fbdev initial configuration
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: drm/i915/fbdev: Enable late fbdev initial configuration
URL : https://patchwork.freedesktop.org/series/41851/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4060_full -> Patchwork_8714_full =
== Summary - WARNING ==
Minor unknown changes coming with Patchwork_8714_full need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_8714_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
External URL: https://patchwork.freedesktop.org/api/1.0/series/41851/revisions/1/mbox/
== Possible new issues ==
Here are the unknown changes that may have been introduced in Patchwork_8714_full:
=== IGT changes ===
==== Warnings ====
igt@gem_exec_schedule@deep-bsd1:
shard-kbl: SKIP -> PASS +1
igt@gem_mocs_settings@mocs-rc6-dirty-render:
shard-kbl: PASS -> SKIP== Known issues ==
Here are the changes found in Patchwork_8714_full that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@kms_atomic_transition@1x-modeset-transitions-fencing:
shard-hsw: PASS -> DMESG-WARN (fdo#102614)
igt@kms_flip@modeset-vs-vblank-race:
shard-apl: PASS -> FAIL (fdo#103060)
igt@kms_sysfs_edid_timing:
shard-apl: PASS -> WARN (fdo#100047)
==== Possible fixes ====
igt@gem_ppgtt@blt-vs-render-ctx0:
shard-kbl: INCOMPLETE (fdo#103665, fdo#106023) -> PASS
igt@kms_cursor_legacy@2x-long-flip-vs-cursor-atomic:
shard-hsw: FAIL (fdo#104873) -> PASS fdo#100047 https://bugs.freedesktop.org/show_bug.cgi?id=100047
fdo#102614 https://bugs.freedesktop.org/show_bug.cgi?id=102614
fdo#103060 https://bugs.freedesktop.org/show_bug.cgi?id=103060
fdo#103665 https://bugs.freedesktop.org/show_bug.cgi?id=103665
fdo#104873 https://bugs.freedesktop.org/show_bug.cgi?id=104873
fdo#106023 https://bugs.freedesktop.org/show_bug.cgi?id=106023
== Participating hosts (6 -> 4) ==
Missing (2): shard-glk shard-glkb
== Build changes ==
* Linux: CI_DRM_4060 -> Patchwork_8714
CI_DRM_4060: 17148956c3830de3194c17693be76f85f05f692f @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4441: 83ba5b7d3bde48b383df41792fc9c955a5a23bdb @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_8714: 07a7c687e23721dccc869d9c0a4e2b0b1e817396 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4441: e60d247eb359f044caf0c09904da14e39d7adca1 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_8714/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.BAT: failure for drm/i915/fbdev: Enable late fbdev initial configuration (rev3)
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: drm/i915/fbdev: Enable late fbdev initial configuration (rev3)
URL : https://patchwork.freedesktop.org/series/41851/
State : failure
== Summary ==
Applying: drm/i915/fbdev: Enable late fbdev initial configuration
error: patch failed: drivers/gpu/drm/i915/intel_fbdev.c:807
error: drivers/gpu/drm/i915/intel_fbdev.c: patch does not apply
error: Did you hand edit your patch?
It does not apply to blobs recorded in its index.
Using index info to reconstruct a base tree...
Patch failed at 0001 drm/i915/fbdev: Enable late fbdev initial configuration The copy of the patch that failed is found in: .git/rebase-apply/patch When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead. To restore the original branch and stop patching, run "git am --abort".
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx