Skip to contentSkip to conversation

drm: Add connector property to limit max bpc

PATCH Superseded Radhakrishna Sripada 3 participants 6 messages Aug 30, 2018

Subsystems (3)

v4 of 14 Superseded Latest is v14 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/2 drm: Add connector property to limit max bpc

At times 12bpc HDMI cannot be driven due to faulty cables, dongles level shifters etc. To workaround them we may need to drive the output at a lower bpc. Currently the user space does not have a way to limit the bpc. The default bpc to be programmed is decided by the driver and is run against connector limitations.

Creating a new connector property "max bpc" in order to limit the bpc. xrandr can make use of this connector property to make sure that bpc does not exceed the configured value. This property can be used by userspace to set the bpc.

V2: Initialize max_bpc to satisfy kms_properties
V3: Move the property to drm_connector
V4: Split drm and i915 components(Ville)

Cc Ville Syrjälä <[email protected]>
Cc Kishore Kadiyala <[email protected]>
Cc Rodrigo Vivi <[email protected]>
Cc Manasi Navare <[email protected]>
Cc Stanislav Lisovskiy <[email protected]>
---
 drivers/gpu/drm/drm_atomic.c        | 4 ++++
 drivers/gpu/drm/drm_atomic_helper.c | 4 ++++
 include/drm/drm_connector.h         | 6 ++++++
 include/drm/drm_mode_config.h       | 5 +++++
 4 files changed, 19 insertions(+)
drivers/gpu/drm/drm_atomic.c +4 -0
index d0478abc01bd..4e352fc1f0a0 100644
@@ -1420,6 +1420,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector,
 
 		return set_out_fence_for_connector(state->state, connector,
 						   fence_ptr);
+	} else if (property == config->max_bpc_property) {
+		state->max_bpc = val;
 	} else if (connector->funcs->atomic_set_property) {
 		return connector->funcs->atomic_set_property(connector,
 				state, property, val);
@@ -1515,6 +1517,8 @@ drm_atomic_connector_get_property(struct drm_connector *connector,
 		*val = 0;
 	} else if (property == config->writeback_out_fence_ptr_property) {
 		*val = 0;
+	} else if (property == config->max_bpc_property) {
+		*val = state->max_bpc;
 	} else if (connector->funcs->atomic_get_property) {
 		return connector->funcs->atomic_get_property(connector,
 				state, property, val);
drivers/gpu/drm/drm_atomic_helper.c +4 -0
index 2c23a48482da..7f763650a623 100644
@@ -638,6 +638,10 @@ drm_atomic_helper_check_modeset(struct drm_device *dev,
 			if (old_connector_state->link_status !=
 			    new_connector_state->link_status)
 				new_crtc_state->connectors_changed = true;
+
+			if (old_connector_state->max_bpc !=
+			    new_connector_state->max_bpc)
+				new_crtc_state->connectors_changed = true;
 		}
 
 		if (funcs->atomic_check)
include/drm/drm_connector.h +6 -0
index 97ea41dc678f..fc11f40aae51 100644
@@ -460,6 +460,12 @@ struct drm_connector_state {
 	 * drm_writeback_signal_completion()
 	 */
 	struct drm_writeback_job *writeback_job;
+
+	/**
+	 * @max_bpc: Connector property to limit the maximum bit depth of
+	 * the pixels.
+	 */
+	unsigned int max_bpc;
 };
 
 /**
include/drm/drm_mode_config.h +5 -0
index a0b202e1d69a..b9cd7a73b244 100644
@@ -562,6 +562,11 @@ struct drm_mode_config {
 	 */
 	struct drm_property *link_status_property;
 	/**
+	 * @max_bpc_property: Default connector property for the max bpc to be
+	 * driven out of the connector.
+	 */
+	struct drm_property *max_bpc_property;
+	/**
 	 * @plane_type_property: Default plane property to differentiate
 	 * CURSOR, PRIMARY and OVERLAY legacy uses of planes.
 	 */
Signature · 6 lines
2.9.3

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH v4 2/2 drm/i915: Allow "max bpc" property to limit pipe_bpp

Use the newly added "max bpc" connector property to limit pipe bpp.

V3: Use drm_connector_state to access the "max bpc" property
V4: Initialize the drm property, add suuport to DP(Ville)

Cc Ville Syrjälä <[email protected]>
Cc Rodrigo Vivi <[email protected]>
Cc Kishore Kadiyala <[email protected]>
Cc Manasi Navare <[email protected]>
Cc Stanislav Lisovskiy <[email protected]>
---
 drivers/gpu/drm/i915/intel_display.c | 25 +++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dp.c      |  1 +
 drivers/gpu/drm/i915/intel_drv.h     |  2 ++
 drivers/gpu/drm/i915/intel_hdmi.c    |  7 +++++++
 drivers/gpu/drm/i915/intel_modes.c   | 21 +++++++++++++++++++++
 5 files changed, 56 insertions(+)
drivers/gpu/drm/i915/intel_display.c +25 -0
index 4bb46f289c0d..216fd4b689b5 100644
@@ -10783,6 +10783,28 @@ connected_sink_compute_bpp(struct intel_connector *connector,
 	}
 }
 
+static void
+connected_sink_max_bpp(struct drm_connector_state *conn_state,
+			     struct intel_crtc_state *pipe_config)
+{
+	switch (conn_state->max_bpc) {
+	case 8:
+	case 9:
+		pipe_config->pipe_bpp = 8*3;
+		break;
+	case 10:
+	case 11:
+		pipe_config->pipe_bpp = 10*3;
+		break;
+	case 12:
+		pipe_config->pipe_bpp = 12*3;
+		break;
+	default:
+		break;
+	}
+	DRM_DEBUG_KMS("Limiting display bpp to %d\n", pipe_config->pipe_bpp);
+}
+
 static int
 compute_baseline_pipe_bpp(struct intel_crtc *crtc,
 			  struct intel_crtc_state *pipe_config)
@@ -10811,6 +10833,9 @@ compute_baseline_pipe_bpp(struct intel_crtc *crtc,
 		if (connector_state->crtc != &crtc->base)
 			continue;
 
+		if (connector_state->max_bpc)
+			connected_sink_max_bpp(connector_state, pipe_config);
+
 		connected_sink_compute_bpp(to_intel_connector(connector),
 					   pipe_config);
 	}
drivers/gpu/drm/i915/intel_dp.c +1 -0
index 436c22de33b6..1c2d38b7f6ab 100644
@@ -5719,6 +5719,7 @@ intel_dp_add_properties(struct intel_dp *intel_dp, struct drm_connector *connect
 		intel_attach_force_audio_property(connector);
 
 	intel_attach_broadcast_rgb_property(connector);
+	intel_attach_max_bpc_property(connector, 6, 16);
 
 	if (intel_dp_is_edp(intel_dp)) {
 		u32 allowed_scalers;
drivers/gpu/drm/i915/intel_drv.h +2 -0
index f5731215210a..b3c703dacc92 100644
@@ -1869,6 +1869,8 @@ int intel_ddc_get_modes(struct drm_connector *c, struct i2c_adapter *adapter);
 void intel_attach_force_audio_property(struct drm_connector *connector);
 void intel_attach_broadcast_rgb_property(struct drm_connector *connector);
 void intel_attach_aspect_ratio_property(struct drm_connector *connector);
+void intel_attach_max_bpc_property(struct drm_connector *connector, int min, int
+				   max);
 
 
 /* intel_overlay.c */
drivers/gpu/drm/i915/intel_hdmi.c +7 -0
index a2dab0b6bde6..e649bbf07642 100644
@@ -2109,11 +2109,18 @@ static const struct drm_encoder_funcs intel_hdmi_enc_funcs = {
 static void
 intel_hdmi_add_properties(struct intel_hdmi *intel_hdmi, struct drm_connector *connector)
 {
+	struct drm_i915_private *dev_priv = to_i915(connector->dev);
+
 	intel_attach_force_audio_property(connector);
 	intel_attach_broadcast_rgb_property(connector);
 	intel_attach_aspect_ratio_property(connector);
 	drm_connector_attach_content_type_property(connector);
 	connector->state->picture_aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
+
+	if (HAS_GMCH_DISPLAY(dev_priv))
+		intel_attach_max_bpc_property(connector, 8, 8);
+	else
+		intel_attach_max_bpc_property(connector, 8, 12);
 }
 
 /*
drivers/gpu/drm/i915/intel_modes.c +21 -0
index ca44bf368e24..eb1eaad0115e 100644
@@ -133,3 +133,24 @@ intel_attach_aspect_ratio_property(struct drm_connector *connector)
 			connector->dev->mode_config.aspect_ratio_property,
 			DRM_MODE_PICTURE_ASPECT_NONE);
 }
+
+void
+intel_attach_max_bpc_property(struct drm_connector *connector, int min, int
+			       max)
+{
+	struct drm_device *dev = connector->dev;
+	struct drm_mode_config *config = &dev->mode_config;
+	struct drm_property *prop;
+
+	prop = config->max_bpc_property;
+	if (prop == NULL) {
+		prop = drm_property_create_range(dev, 0, "max bpc", min, max);
+		if (prop == NULL)
+			return;
+
+		config->max_bpc_property = prop;
+	}
+
+	drm_object_attach_property(&connector->base, prop, max);
+	connector->state->max_bpc = max;
+}
Signature · 6 lines
2.9.3

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#2 lore raw
In reply to Radhakrishna Sripada
Quoted 87 lines · Radhakrishna Sripada

At times 12bpc HDMI cannot be driven due to faulty cables, dongles level shifters etc. To workaround them we may need to drive the output at a lower bpc. Currently the user space does not have a way to limit the bpc. The default bpc to be programmed is decided by the driver and is run against connector limitations.

Creating a new connector property "max bpc" in order to limit the bpc. xrandr can make use of this connector property to make sure that bpc does not exceed the configured value. This property can be used by userspace to set the bpc.

V2: Initialize max_bpc to satisfy kms_properties
V3: Move the property to drm_connector
V4: Split drm and i915 components(Ville)

Cc Ville Syrjälä <[email protected]>
Cc Kishore Kadiyala <[email protected]>
Cc Rodrigo Vivi <[email protected]>
Cc Manasi Navare <[email protected]>
Cc Stanislav Lisovskiy <[email protected]>
---
 drivers/gpu/drm/drm_atomic.c        | 4 ++++
 drivers/gpu/drm/drm_atomic_helper.c | 4 ++++
 include/drm/drm_connector.h         | 6 ++++++
 include/drm/drm_mode_config.h       | 5 +++++
 4 files changed, 19 insertions(+)
drivers/gpu/drm/drm_atomic.c +4 -0
index d0478abc01bd..4e352fc1f0a0 100644
@@ -1420,6 +1420,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector,
 
 		return set_out_fence_for_connector(state->state, connector,
 						   fence_ptr);
+	} else if (property == config->max_bpc_property) {
+		state->max_bpc = val;
 	} else if (connector->funcs->atomic_set_property) {
 		return connector->funcs->atomic_set_property(connector,
 				state, property, val);
@@ -1515,6 +1517,8 @@ drm_atomic_connector_get_property(struct drm_connector *connector,
 		*val = 0;
 	} else if (property == config->writeback_out_fence_ptr_property) {
 		*val = 0;
+	} else if (property == config->max_bpc_property) {
+		*val = state->max_bpc;
 	} else if (connector->funcs->atomic_get_property) {
 		return connector->funcs->atomic_get_property(connector,
 				state, property, val);
drivers/gpu/drm/drm_atomic_helper.c +4 -0
index 2c23a48482da..7f763650a623 100644
@@ -638,6 +638,10 @@ drm_atomic_helper_check_modeset(struct drm_device *dev,
 			if (old_connector_state->link_status !=
 			    new_connector_state->link_status)
 				new_crtc_state->connectors_changed = true;
+
+			if (old_connector_state->max_bpc !=
+			    new_connector_state->max_bpc)
+				new_crtc_state->connectors_changed = true;
 		}
 
 		if (funcs->atomic_check)
include/drm/drm_connector.h +6 -0
index 97ea41dc678f..fc11f40aae51 100644
@@ -460,6 +460,12 @@ struct drm_connector_state {
 	 * drm_writeback_signal_completion()
 	 */
 	struct drm_writeback_job *writeback_job;
+
+	/**
+	 * @max_bpc: Connector property to limit the maximum bit depth of
+	 * the pixels.
+	 */
+	unsigned int max_bpc;
 };
 
 /**
include/drm/drm_mode_config.h +0 -0
index a0b202e1d69a..b9cd7a73b244 100644

include/drm/drm_mode_config.h struct drm_mode_config { · line 568

Quoted 7 lines
include/drm/drm_mode_config.h +4 -0
@@ -562,6 +562,11 @@ struct drm_mode_config {
 	 */
 	struct drm_property *link_status_property;
 	/**
+	 * @max_bpc_property: Default connector property for the max bpc to be
+	 * driven out of the connector.
+	 */
+	struct drm_property *max_bpc_property;

If we want the exposed limits to be accurate this needs to be per-connector. The other option of course is to just expose the global min-max range for the entire device.

The way you wrote the i915 bits suggest you wanted to go for the per-connector apporach instead.

Quoted 6 lines
include/drm/drm_mode_config.h +1 -0
+	/**
 	 * @plane_type_property: Default plane property to differentiate
 	 * CURSOR, PRIMARY and OVERLAY legacy uses of planes.
 	 */
Signature · 1 line
2.9.3
Signature · 6 lines
Ville Syrjälä
Intel
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#3 lore raw

✗ Fi.CI.CHECKPATCH: warning for series starting with [v4,1/2] drm: Add connector property to limit max bpc

In reply to Radhakrishna Sripada
== Series Details ==

== Series Details ==

Series: series starting with [v4,1/2] drm: Add connector property to limit max bpc
URL : https://patchwork.freedesktop.org/series/48960/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
a2b1ae142db2 drm: Add connector property to limit max bpc
3555676ce4a1 drm/i915: Allow "max bpc" property to limit pipe_bpp
-:31: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#31: FILE: drivers/gpu/drm/i915/intel_display.c:10788:
+connected_sink_max_bpp(struct drm_connector_state *conn_state,
+			     struct intel_crtc_state *pipe_config)

-:36: CHECK:SPACING: spaces preferred around that '*' (ctx:VxV) #36: FILE: drivers/gpu/drm/i915/intel_display.c:10793:
+ pipe_config->pipe_bpp = 8*3;
^

-:40: CHECK:SPACING: spaces preferred around that '*' (ctx:VxV) #40: FILE: drivers/gpu/drm/i915/intel_display.c:10797:
+ pipe_config->pipe_bpp = 10*3;
^

-:43: CHECK:SPACING: spaces preferred around that '*' (ctx:VxV) #43: FILE: drivers/gpu/drm/i915/intel_display.c:10800:
+ pipe_config->pipe_bpp = 12*3;
^

-:130: CHECK:COMPARISON_TO_NULL: Comparison to NULL could be written "!prop" #130: FILE: drivers/gpu/drm/i915/intel_modes.c:146:
+ if (prop == NULL) {

-:132: CHECK:COMPARISON_TO_NULL: Comparison to NULL could be written "!prop" #132: FILE: drivers/gpu/drm/i915/intel_modes.c:148:
+ if (prop == NULL)

total: 0 errors, 0 warnings, 6 checks, 94 lines checked

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#4 lore raw

✓ Fi.CI.BAT: success for series starting with [v4,1/2] drm: Add connector property to limit max bpc

In reply to Radhakrishna Sripada
== Series Details ==

== Series Details ==

Series: series starting with [v4,1/2] drm: Add connector property to limit max bpc
URL : https://patchwork.freedesktop.org/series/48960/
State : success

== Summary ==

= CI Bug Log - changes from CI_DRM_4740 -> Patchwork_10054 =

== Summary - SUCCESS ==

No regressions found.

External URL: https://patchwork.freedesktop.org/api/1.0/series/48960/revisions/1/mbox/

== Known issues ==

Here are the changes found in Patchwork_10054 that come from known issues:

=== IGT changes ===

    ==== Issues hit ====

    igt@debugfs_test@read_all_entries:
      fi-snb-2520m:       PASS -> INCOMPLETE (fdo#103713)

    igt@gem_exec_suspend@basic-s3:
      {fi-cfl-8109u}:     PASS -> INCOMPLETE (fdo#107187)
      {fi-kbl-soraka}:    NOTRUN -> INCOMPLETE (fdo#107556)

    igt@kms_frontbuffer_tracking@basic:
      {fi-byt-clapper}:   PASS -> FAIL (fdo#103167)

    igt@kms_pipe_crc_basic@read-crc-pipe-a:
      {fi-byt-clapper}:   PASS -> FAIL (fdo#107362)

    
    ==== Possible fixes ====

    {igt@amdgpu/amd_prime@i915-to-amd}:
      fi-bxt-j4205:       INCOMPLETE (fdo#103927) -> SKIP

    igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
      {fi-byt-clapper}:   FAIL (fdo#107362, fdo#103191) -> PASS

    {igt@pm_rpm@module-reload}:
      fi-bxt-j4205:       DMESG-FAIL (fdo#107712) -> PASS

{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).

fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#103713 https://bugs.freedesktop.org/show_bug.cgi?id=103713
fdo#103927 https://bugs.freedesktop.org/show_bug.cgi?id=103927
fdo#107187 https://bugs.freedesktop.org/show_bug.cgi?id=107187
fdo#107362 https://bugs.freedesktop.org/show_bug.cgi?id=107362
fdo#107556 https://bugs.freedesktop.org/show_bug.cgi?id=107556
fdo#107712 https://bugs.freedesktop.org/show_bug.cgi?id=107712

== Participating hosts (53 -> 49) ==

Additional (1): fi-kbl-soraka
Missing (5): fi-ctg-p8600 fi-ilk-m540 fi-byt-squawks fi-bsw-cyan fi-hsw-4200u

== Build changes ==

* Linux: CI_DRM_4740 -> Patchwork_10054

CI_DRM_4740: dc30149e06cea1672bac53f0fa7b8f5606ca8d1c @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4612: e39e09910fc8e369e24f6a0cabaeb9356dbfae08 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10054: 3555676ce4a1f6a6ddbdc4b5ff425e12826628f6 @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

3555676ce4a1 drm/i915: Allow "max bpc" property to limit pipe_bpp a2b1ae142db2 drm: Add connector property to limit max bpc

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10054/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#5 lore raw

✗ Fi.CI.IGT: failure for series starting with [v4,1/2] drm: Add connector property to limit max bpc

In reply to Radhakrishna Sripada
== Series Details ==

== Series Details ==

Series: series starting with [v4,1/2] drm: Add connector property to limit max bpc
URL : https://patchwork.freedesktop.org/series/48960/
State : failure

== Summary ==

= CI Bug Log - changes from CI_DRM_4740_full -> Patchwork_10054_full =

== Summary - FAILURE ==

Serious unknown changes coming with Patchwork_10054_full absolutely need to be verified manually.

If you think the reported changes have nothing to do with the changes introduced in Patchwork_10054_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.

== Possible new issues ==

Here are the unknown changes that may have been introduced in Patchwork_10054_full:

=== IGT changes ===

    ==== Possible regressions ====

    igt@kms_properties@get_properties-sanity-atomic:
      shard-hsw:          PASS -> FAIL +3

    igt@kms_properties@get_properties-sanity-non-atomic:
      shard-snb:          PASS -> FAIL +3

    
    ==== Warnings ====

    igt@kms_cursor_legacy@flip-vs-cursor-legacy:
      shard-snb:          SKIP -> PASS +2

== Known issues ==

Here are the changes found in Patchwork_10054_full that come from known issues:

=== IGT changes ===

    ==== Issues hit ====

    igt@drv_suspend@shrink:
      shard-glk:          PASS -> INCOMPLETE (fdo#106886, k.org#198133, fdo#103359)

    igt@kms_cursor_legacy@cursor-vs-flip-atomic-transitions-varying-size:
      shard-hsw:          PASS -> FAIL (fdo#103355)

    igt@kms_plane@plane-panning-bottom-right-suspend-pipe-b-planes:
      shard-apl:          PASS -> FAIL (fdo#103375)

    igt@kms_setmode@basic:
      shard-apl:          PASS -> FAIL (fdo#99912)

    igt@perf_pmu@enable-race-bcs0:
      shard-snb:          SKIP -> INCOMPLETE (fdo#105411)

    
    ==== Possible fixes ====

    igt@drv_suspend@shrink:
      shard-hsw:          INCOMPLETE (fdo#106886, fdo#103540) -> PASS

    igt@gem_exec_await@wide-contexts:
      shard-kbl:          FAIL (fdo#105900) -> PASS

    igt@gem_render_linear_blits@basic:
      shard-kbl:          INCOMPLETE (fdo#103665) -> PASS

    igt@kms_cursor_legacy@2x-long-cursor-vs-flip-atomic:
      shard-hsw:          FAIL (fdo#105767) -> PASS

    igt@kms_frontbuffer_tracking@fbc-badstride:
      shard-glk:          FAIL (fdo#103167) -> PASS

    igt@perf@polling:
      shard-hsw:          FAIL (fdo#102252) -> PASS

fdo#102252 https://bugs.freedesktop.org/show_bug.cgi?id=102252
fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fdo#103355 https://bugs.freedesktop.org/show_bug.cgi?id=103355
fdo#103359 https://bugs.freedesktop.org/show_bug.cgi?id=103359
fdo#103375 https://bugs.freedesktop.org/show_bug.cgi?id=103375
fdo#103540 https://bugs.freedesktop.org/show_bug.cgi?id=103540
fdo#103665 https://bugs.freedesktop.org/show_bug.cgi?id=103665
fdo#105411 https://bugs.freedesktop.org/show_bug.cgi?id=105411
fdo#105767 https://bugs.freedesktop.org/show_bug.cgi?id=105767
fdo#105900 https://bugs.freedesktop.org/show_bug.cgi?id=105900
fdo#106886 https://bugs.freedesktop.org/show_bug.cgi?id=106886
fdo#99912 https://bugs.freedesktop.org/show_bug.cgi?id=99912
k.org#198133 https://bugzilla.kernel.org/show_bug.cgi?id=198133

== Participating hosts (5 -> 5) ==

No changes in participating hosts

== Build changes ==

* Linux: CI_DRM_4740 -> Patchwork_10054

CI_DRM_4740: dc30149e06cea1672bac53f0fa7b8f5606ca8d1c @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4612: e39e09910fc8e369e24f6a0cabaeb9356dbfae08 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10054: 3555676ce4a1f6a6ddbdc4b5ff425e12826628f6 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10054/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx