Skip to contentSkip to conversation

pico-imx6ul: Convert to distro config

PATCH Superseded Otavio Salvador 4 participants 23 messages Aug 30, 2018 – Sep 4, 2018

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/13 pico-imx6ul: Convert to distro config

From: Fabio Estevam <[email protected]>

Instead of keeping a custom environment, use a more generic approach by switching to disto config.

---

 configs/pico-imx6ul_defconfig |  2 +
 include/configs/pico-imx6ul.h | 69 ++++++++++-------------------------
 2 files changed, 21 insertions(+), 50 deletions(-)
configs/pico-imx6ul_defconfig +2 -0
index 59ef7b7f22..3f969a2d6e 100644
@@ -4,7 +4,9 @@ CONFIG_SYS_TEXT_BASE=0x87800000
 CONFIG_TARGET_PICO_IMX6UL=y
 # CONFIG_CMD_BMODE is not set
 CONFIG_NR_DRAM_BANKS=1
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx6ul/imximage.cfg"
+CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
 CONFIG_BOOTDELAY=3
 CONFIG_SUPPORT_RAW_INITRD=y
 CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
include/configs/pico-imx6ul.h +19 -50

83 lines not on this page · raw message

Signature · 1 line
2.18.0
#1 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

From: Fabio Estevam <[email protected]>

There are two versions of imx6ul pico SOMs: one with 256MB and another one with 512MB of RAM.

Convert to SPL so that both versions can be supported.

Currently only the 256MB is tested/supported.

---

 arch/arm/mach-imx/mx6/Kconfig         |   1 +
 board/technexion/pico-imx6ul/Makefile |   2 +-
 board/technexion/pico-imx6ul/spl.c    | 115 ++++++++++++++++++++++++++
 configs/pico-imx6ul_defconfig         |  14 +++-
 include/configs/pico-imx6ul.h         |   1 +
 5 files changed, 131 insertions(+), 2 deletions(-)
 create mode 100644 board/technexion/pico-imx6ul/spl.c
arch/arm/mach-imx/mx6/Kconfig +1 -0
index a2799c436e..06c25bae36 100644
@@ -402,6 +402,7 @@ config TARGET_OT1200
 config TARGET_PICO_IMX6UL
 	bool "PICO-IMX6UL-EMMC"
 	select MX6UL
+	select SUPPORT_SPL
 
 config TARGET_LITEBOARD
 	bool "Grinn liteBoard (i.MX6UL)"
board/technexion/pico-imx6ul/Makefile +1 -1
index 8fdb7875ac..b7493df01c 100644
@@ -2,4 +2,4 @@
 # (C) Copyright 2015 Technexion Ltd.
 # (C) Copyright 2015 Freescale Semiconductor, Inc.
 
-obj-y  := pico-imx6ul.o
+obj-y  := pico-imx6ul.o spl.o
board/technexion/pico-imx6ul/spl.c new file +115 -0

115 lines not on this page · raw message

configs/pico-imx6ul_defconfig +13 -1
index 3f969a2d6e..589e67be96 100644
@@ -1,12 +1,23 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MX6=y
 CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_TARGET_PICO_IMX6UL=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
 # CONFIG_CMD_BMODE is not set
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx6ul/imximage.cfg"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
 CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_USB_GADGET_SUPPORT=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
 CONFIG_BOOTDELAY=3
 CONFIG_SUPPORT_RAW_INITRD=y
 CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
@@ -21,6 +32,7 @@ CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_PART=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
 CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
include/configs/pico-imx6ul.h +1 -0
index 1a148bf1a6..14d5cc3ddb 100644
@@ -12,6 +12,7 @@
 #include <linux/sizes.h>
 #include "mx6_common.h"
 #include <asm/mach-imx/gpio.h>
+#include "imx6_spl.h"
 
 /* Network support */
 
Signature · 1 line
2.18.0
#2 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Quoted 50 lines · Otavio Salvador

From: Fabio Estevam <[email protected]>

There are two versions of imx6ul pico SOMs: one with 256MB and another one with 512MB of RAM.

Convert to SPL so that both versions can be supported.

Currently only the 256MB is tested/supported.

---

 arch/arm/mach-imx/mx6/Kconfig         |   1 +
 board/technexion/pico-imx6ul/Makefile |   2 +-
 board/technexion/pico-imx6ul/spl.c    | 115 ++++++++++++++++++++++++++
 configs/pico-imx6ul_defconfig         |  14 +++-
 include/configs/pico-imx6ul.h         |   1 +
 5 files changed, 131 insertions(+), 2 deletions(-)
 create mode 100644 board/technexion/pico-imx6ul/spl.c
arch/arm/mach-imx/mx6/Kconfig +1 -0
index a2799c436e..06c25bae36 100644
@@ -402,6 +402,7 @@ config TARGET_OT1200
 config TARGET_PICO_IMX6UL
        bool "PICO-IMX6UL-EMMC"
        select MX6UL
+       select SUPPORT_SPL
 
 config TARGET_LITEBOARD
        bool "Grinn liteBoard (i.MX6UL)"
board/technexion/pico-imx6ul/Makefile +1 -1
index 8fdb7875ac..b7493df01c 100644
@@ -2,4 +2,4 @@
 # (C) Copyright 2015 Technexion Ltd.
 # (C) Copyright 2015 Freescale Semiconductor, Inc.
 
-obj-y  := pico-imx6ul.o
+obj-y  := pico-imx6ul.o spl.o
board/technexion/pico-imx6ul/spl.c new file +0 -0
new file mode 100644
index 0000000000..6989c81946

board/technexion/pico-imx6ul/spl.c line 1

Quoted 1 line
board/technexion/pico-imx6ul/spl.c new file +1 -0
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+

space

Quoted 80 lines
board/technexion/pico-imx6ul/spl.c new file +80 -0
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ul_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <linux/libfdt.h>
+#include <spl.h>
+
+#if defined(CONFIG_SPL_BUILD)
+#include <asm/arch/mx6-ddr.h>
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+       .grp_addds = 0x00000030,
+       .grp_ddrmode_ctl = 0x00020000,
+       .grp_b0ds = 0x00000030,
+       .grp_ctlds = 0x00000030,
+       .grp_b1ds = 0x00000030,
+       .grp_ddrpke = 0x00000000,
+       .grp_ddrmode = 0x00020000,
+       .grp_ddr_type = 0x00080000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+       .dram_dqm0 = 0x00000030,
+       .dram_dqm1 = 0x00000030,
+       .dram_ras = 0x00000030,
+       .dram_cas = 0x00000030,
+       .dram_odt0 = 0x00000030,
+       .dram_odt1 = 0x00000030,
+       .dram_sdba2 = 0x00000000,
+       .dram_sdclk_0 = 0x00000030,
+       .dram_sdqs0 = 0x00000030,
+       .dram_sdqs1 = 0x00000030,
+       .dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+       .p0_mpwldectrl0 = 0x00000000,
+       .p0_mpdgctrl0 = 0x01380134,
+       .p0_mprddlctl = 0x40404244,
+       .p0_mpwrdlctl = 0x40405050,
+};
+
+static struct mx6_ddr_sysinfo ddr_sysinfo = {
+       .dsize          = 0,
+       .cs1_mirror     = 0,
+       .cs_density     = 32,
+       .ncs            = 1,
+       .bi_on          = 1,
+       .rtt_nom        = 1,
+       .rtt_wr         = 0,
+       .ralat          = 5,
+       .walat          = 0,
+       .mif3_mode      = 3,
+       .rst_to_cke     = 0x23,
+       .sde_to_rst     = 0x10,
+       .refsel = 1,
+       .refr = 3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+       .mem_speed = 1333,
+       .density = 2,
+       .width = 16,
+       .banks = 8,
+       .rowaddr = 14,
+       .coladdr = 10,
+       .pagesz = 2,
+       .trcd = 1350,
+       .trcmin = 4950,
+       .trasmin = 3600,
+};
+
+static void ccgr_init(void)
+{

board/technexion/pico-imx6ul/spl.c line 91

Quoted 10 lines
board/technexion/pico-imx6ul/spl.c new file +10 -0
+       struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+       writel(0xFFFFFFFF, &ccm->CCGR0);
+       writel(0xFFFFFFFF, &ccm->CCGR1);
+       writel(0xFFFFFFFF, &ccm->CCGR2);
+       writel(0xFFFFFFFF, &ccm->CCGR3);
+       writel(0xFFFFFFFF, &ccm->CCGR4);
+       writel(0xFFFFFFFF, &ccm->CCGR5);
+       writel(0xFFFFFFFF, &ccm->CCGR6);
+       writel(0xFFFFFFFF, &ccm->CCGR7);

These can be know values.

reviewer
#3 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi Jagan,

Quoted 8 lines · Jagan Teki

board/technexion/pico-imx6ul/spl.c line 1

Quoted 4 lines
board/technexion/pico-imx6ul/spl.c new file +1 -0
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+

space

Quoted 14 lines

board/technexion/pico-imx6ul/spl.c line 91

Quoted 12 lines
board/technexion/pico-imx6ul/spl.c new file +12 -0
+static void ccgr_init(void)
+{
+       struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+       writel(0xFFFFFFFF, &ccm->CCGR0);
+       writel(0xFFFFFFFF, &ccm->CCGR1);
+       writel(0xFFFFFFFF, &ccm->CCGR2);
+       writel(0xFFFFFFFF, &ccm->CCGR3);
+       writel(0xFFFFFFFF, &ccm->CCGR4);
+       writel(0xFFFFFFFF, &ccm->CCGR5);
+       writel(0xFFFFFFFF, &ccm->CCGR6);
+       writel(0xFFFFFFFF, &ccm->CCGR7);

These can be know values.

I am sorry, but I did not understand your comments.

Please clarify.

Thanks

#4 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi Fabio

Quoted 13 lines · Fabio Estevam

Hi Jagan,

Quoted 7 lines · Jagan Teki

board/technexion/pico-imx6ul/spl.c line 1

Quoted 4 lines
board/technexion/pico-imx6ul/spl.c new file +1 -0
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+

space

Quoted 12 lines
Quoted 4 lines
Quoted 4 lines
board/technexion/pico-imx6ul/spl.c new file +4 -0
+static void ccgr_init(void)
+{
+       struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
Quoted 8 lines

board/technexion/pico-imx6ul/spl.c line 91

Quoted 8 lines
board/technexion/pico-imx6ul/spl.c new file +8 -0
+       writel(0xFFFFFFFF, &ccm->CCGR0);
+       writel(0xFFFFFFFF, &ccm->CCGR1);
+       writel(0xFFFFFFFF, &ccm->CCGR2);
+       writel(0xFFFFFFFF, &ccm->CCGR3);
+       writel(0xFFFFFFFF, &ccm->CCGR4);
+       writel(0xFFFFFFFF, &ccm->CCGR5);
+       writel(0xFFFFFFFF, &ccm->CCGR6);
+       writel(0xFFFFFFFF, &ccm->CCGR7);

are you sure that arrive to 7?

Quoted 5 lines
Quoted 2 lines

These can be know values.

I am sorry, but I did not understand your comments.

I think that it's not a good strategy to enable all the gate in general here.

Michael

Quoted 7 lines

Please clarify.

Thanks
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

Signature · 4 lines
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
reviewer
#5 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi Michael,

Quoted 6 lines · Michael Nazzareno Trimarchi
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
board/technexion/pico-imx6ul/spl.c new file +6 -0
+static void ccgr_init(void)
+{
+       struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+       writel(0xFFFFFFFF, &ccm->CCGR0);
+       writel(0xFFFFFFFF, &ccm->CCGR1);
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines

board/technexion/pico-imx6ul/spl.c line 91

Quoted 6 lines
board/technexion/pico-imx6ul/spl.c new file +6 -0
+       writel(0xFFFFFFFF, &ccm->CCGR2);
+       writel(0xFFFFFFFF, &ccm->CCGR3);
+       writel(0xFFFFFFFF, &ccm->CCGR4);
+       writel(0xFFFFFFFF, &ccm->CCGR5);
+       writel(0xFFFFFFFF, &ccm->CCGR6);
+       writel(0xFFFFFFFF, &ccm->CCGR7);

are you sure that arrive to 7?

You are right. CCGR7 is not available on mx6ul. I will fix it.

Quoted 1 line

I think that it's not a good strategy to enable all the gate in general here.

Yes, the main point of this patch is to convert from DCD table to SPL.

As the DCD table enables all the clocks I kept the same approach.

I agree that this can be further improved by only turning on the clocks that are used by the bootloader.

However this is subject for a separate patch.

Thanks

#6 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi

Quoted 23 lines · Fabio Estevam

Hi Michael,

Quoted 6 lines · Michael Nazzareno Trimarchi
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
board/technexion/pico-imx6ul/spl.c new file +6 -0
+static void ccgr_init(void)
+{
+       struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+       writel(0xFFFFFFFF, &ccm->CCGR0);
+       writel(0xFFFFFFFF, &ccm->CCGR1);
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines

board/technexion/pico-imx6ul/spl.c line 91

Quoted 6 lines
board/technexion/pico-imx6ul/spl.c new file +6 -0
+       writel(0xFFFFFFFF, &ccm->CCGR2);
+       writel(0xFFFFFFFF, &ccm->CCGR3);
+       writel(0xFFFFFFFF, &ccm->CCGR4);
+       writel(0xFFFFFFFF, &ccm->CCGR5);
+       writel(0xFFFFFFFF, &ccm->CCGR6);
+       writel(0xFFFFFFFF, &ccm->CCGR7);

are you sure that arrive to 7?

You are right. CCGR7 is not available on mx6ul. I will fix it.

Quoted 8 lines
Quoted 1 line

I think that it's not a good strategy to enable all the gate in general here.

Yes, the main point of this patch is to convert from DCD table to SPL.

As the DCD table enables all the clocks I kept the same approach.

I agree that this can be further improved by only turning on the clocks that are used by the bootloader.

Well, yes and no. Not all the bits can be writable according to the documentation if I remember and if the value you
put are the value after reset and if I remember are all the clock on, you need to explain better you you write them.

Michael

Quoted 4 lines

However this is subject for a separate patch.

Thanks

Signature · 4 lines
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
reviewer
#7 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Quoted 4 lines · Michael Nazzareno Trimarchi

Well, yes and no. Not all the bits can be writable according to the documentation if I remember and if the value you
put are the value after reset and if I remember are all the clock on, you need to explain better you you write them.

0xFFFFFFFF is the value of the CCGR registers after power on reset.

It is true that some fields are marked as "reserved", but I don't see the issue in writing '11' to them since this is the POR value.

Again, I am not doing anything different than the DCD table in this aspect.

#8 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi Fabio

Quoted 9 lines · Fabio Estevam
Quoted 4 lines · Michael Nazzareno Trimarchi

Well, yes and no. Not all the bits can be writable according to the documentation if I remember and if the value you
put are the value after reset and if I remember are all the clock on, you need to explain better you you write them.

Quoted 6 lines

0xFFFFFFFF is the value of the CCGR registers after power on reset.

It is true that some fields are marked as "reserved", but I don't see the issue in writing '11' to them since this is the POR value.

Again, I am not doing anything different than the DCD table in this aspect.

Ok, if you resend with the change discussed I'm fine with it. The reason that I'm trying to make much clean is just because I get random problem in the past just for few bits ;)

Michael

Signature · 4 lines
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
reviewer
#9 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi Michael,

Quoted 3 lines · Michael Nazzareno Trimarchi

Ok, if you resend with the change discussed I'm fine with it. The reason that I'm trying to make much clean is just because I get random problem in the past just for few bits ;)

Sorry, I am not sure what exactly you want me to do differently in v2.

Please clarify.

#10 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

Hi

Quoted 6 lines · Fabio Estevam

Hi Michael,

On Tue, Sep 4, 2018 at 9:53 AM, Michael Nazzareno Trimarchi <[email protected]> wrote:

Quoted 7 lines
Quoted 3 lines

Ok, if you resend with the change discussed I'm fine with it. The reason that I'm trying to make much clean is just because I get random problem in the past just for few bits ;)

Sorry, I am not sure what exactly you want me to do differently in v2.

Please clarify.

I miss v2 ;), I think

Michael

Signature · 4 lines
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
#11 lore raw

PATCH 2/13 pico-imx6ul: Convert to SPL

In reply to Fabio Estevam
Quoted 8 lines · Fabio Estevam
Quoted 4 lines · Michael Nazzareno Trimarchi

Well, yes and no. Not all the bits can be writable according to the documentation if I remember and if the value you
put are the value after reset and if I remember are all the clock on, you need to explain better you you write them.

Quoted 4 lines

0xFFFFFFFF is the value of the CCGR registers after power on reset.

It is true that some fields are marked as "reserved", but I don't see the issue in writing '11' to them since this is the POR value.

I'm just commenting since Stefano did mention the similar this [1] previously. may be he can found any random problem with setting up all 11's

[1] https://lists.denx.de/pipermail/u-boot/2017-January/279566.html

#12 lore raw

PATCH 3/13 pico-imx6ul: Add fastboot support

In reply to Otavio Salvador

From: Fabio Estevam <[email protected]>

fastboot tool is a convenient way to flash the eMMC, so add support for it.

Examples of usages:

On the pico-imx6ul U-Boot prompt:

=> fastboot 0

On the Linux PC connected via USB:

1. Retrieving the U-Boot version

$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc2-00130-g0881835-dirty
finished. total time: 0.000s

2. Resetting the board

$ sudo fastboot reboot -i 0x0525

(this causes the pico-imx6ul to reboot)

---

 configs/pico-imx6ul_defconfig | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
configs/pico-imx6ul_defconfig +6 -1
index 589e67be96..cae7ded1fa 100644
@@ -45,6 +45,12 @@ CONFIG_CMD_FAT=y
 CONFIG_CMD_FS_GENERIC=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_DFU_MMC=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x82000000
+CONFIG_FASTBOOT_BUF_SIZE=0x10000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=0
+CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
 CONFIG_FSL_ESDHC=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
@@ -56,5 +62,4 @@ CONFIG_USB_GADGET_MANUFACTURER="FSL"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0525
 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
 CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_OF_LIBFDT=y
Signature · 1 line
2.18.0
#13 lore raw

PATCH 4/13 pico-imx6ul: Add bmode support

In reply to Otavio Salvador

From: Fabio Estevam <[email protected]>

The 'bmode' command is helpful for switching the boot media.

In the case of pico-imx6ul there are two possible boot media:
eMMC or USB.

To boot from eMMC:

=> bmode emmc

To boot from USB (via Serial Download Protocol):

=> bmode usb

---

 configs/pico-imx6ul_defconfig | 1 -
 1 file changed, 1 deletion(-)
configs/pico-imx6ul_defconfig +0 -1
index cae7ded1fa..daa898fb22 100644
@@ -9,7 +9,6 @@ CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL=y
 CONFIG_SPL_LIBDISK_SUPPORT=y
-# CONFIG_CMD_BMODE is not set
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
Signature · 1 line
2.18.0
#14 lore raw

PATCH 5/13 pico-imx6ul: Add support for the 512MB module

In reply to Otavio Salvador

From: Fabio Estevam <[email protected]>

Currently only the module with 256MB of RAM is supported.

Add support for the 512MB of RAM variant as well.

---

 board/technexion/pico-imx6ul/spl.c | 27 ++++++++++++++++++++++++---
 1 file changed, 24 insertions(+), 3 deletions(-)
board/technexion/pico-imx6ul/spl.c +24 -3
index 6989c81946..428d3b10fb 100644
@@ -69,7 +69,6 @@ static struct mx6_ddr3_cfg mem_ddr = {
 	.density = 2,
 	.width = 16,
 	.banks = 8,
-	.rowaddr = 14,
 	.coladdr = 10,
 	.pagesz = 2,
 	.trcd = 1350,
@@ -91,12 +90,34 @@ static void ccgr_init(void)
 	writel(0xFFFFFFFF, &ccm->CCGR7);
 }
 
-static void spl_dram_init(void)
+static void imx6ul_spl_dram_cfg_size(u32 ram_size)
 {
+	if (ram_size == SZ_256M)
+		mem_ddr.rowaddr = 14;
+	else
+		mem_ddr.rowaddr = 15;
+
 	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
 }
 
+static void imx6ul_spl_dram_cfg(void)
+{
+	ulong ram_size_test, ram_size = 0;
+
+	for (ram_size = SZ_512M; ram_size >= SZ_256M; ram_size >>= 1) {
+		imx6ul_spl_dram_cfg_size(ram_size);
+		ram_size_test = get_ram_size((long int *)PHYS_SDRAM, ram_size);
+		if (ram_size_test == ram_size)
+			break;
+	}
+
+	if (ram_size < SZ_256M) {
+		puts("ERROR: DRAM size detection failed\n");
+		hang();
+	}
+}
+
 void board_init_f(ulong dummy)
 {
 	ccgr_init();
@@ -104,7 +125,7 @@ void board_init_f(ulong dummy)
 	board_early_init_f();
 	timer_init();
 	preloader_console_init();
-	spl_dram_init();
+	imx6ul_spl_dram_cfg();
 	memset(__bss_start, 0, __bss_end - __bss_start);
 	board_init_r(NULL, 0);
 }
Signature · 1 line
2.18.0
#15 lore raw

PATCH 6/13 pico-imx7d: Update the README file

In reply to Otavio Salvador

From: Fabio Estevam <[email protected]>

Update the README file to take into accound the switch to SPL.

---

 board/technexion/pico-imx7d/README | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
board/technexion/pico-imx7d/README +17 -7
index aa9d72c5d1..24eb97e82c 100644
@@ -11,7 +11,13 @@ $ make mrproper
 $ make pico-imx7d_defconfig
 $ make
 
-This generates the U-Boot binary called u-boot.imx.
+This generates the SPL and u-boot.img binaries.
+
+1. Loading U-Boot via USB Serial Download Protocol
+
+Note: This method is convenient for development purposes.
+If the eMMC has already a U-Boot flashed with DFU support then
+the user can go to step 2 below in order to update U-Boot.
 
 Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
 page 3)
@@ -22,11 +28,15 @@ Connect a USB cable between the OTG pico port and the host PC.
 
 Open a terminal program such as minicom.
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy SPL and u-boot.img to the imx_usb_loader folder.
+
+Load the SPL binary via USB:
 
-Load u-boot.imx via USB:
+$ sudo ./imx_usb SPL
 
-$ sudo ./imx_usb u-boot.imx
+Load the u-boot.img binary via USB:
+
+$ sudo ./imx_usb u-boot.img
 
 Then U-Boot starts and its messages appear in the console program.
 
@@ -35,16 +45,16 @@ Use the default environment variables:
 => env default -f -a
 => saveenv
 
+2. Flashing U-Boot into the eMMC
+
 Run the DFU agent so we can flash the new images using dfu-util tool:
 
 => dfu 0 mmc 0
 
-Flash SPL into the eMMC:
+Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
 
 $ sudo dfu-util -D SPL -a spl
 
-Flash u-boot.img into the eMMC:
-
 $ sudo dfu-util -D u-boot.img -a u-boot
 
 Remove power from the pico board.
Signature · 1 line
2.18.0
#16 lore raw

PATCH 7/13 pico-imx6ul: Update the README file

In reply to Otavio Salvador

From: Fabio Estevam <[email protected]>

Update the README file to take into accound the switch to SPL.

---

 board/technexion/pico-imx6ul/README | 26 ++++++++++++++++++++------
 1 file changed, 20 insertions(+), 6 deletions(-)
board/technexion/pico-imx6ul/README +20 -6
index 2f66095097..a5415714ee 100644
@@ -13,7 +13,13 @@ $ make mrproper
 $ make pico-imx6ul_defconfig
 $ make
 
-This will generate the U-Boot binary called u-boot.imx.
+This generates the SPL and u-boot.img binaries.
+
+1. Loading U-Boot via USB Serial Download Protocol
+
+Note: This method is convenient for development purposes.
+If the eMMC has already a U-Boot flashed with DFU support then
+the user can go to step 2 below in order to update U-Boot.
 
 Put pico board in USB download mode (refer to the document
 http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf page 15)
@@ -24,11 +30,15 @@ Connect a USB cable between the OTG pico port and the host PC
 
 Open a terminal program such as minicom
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy SPL and u-boot.img to the imx_usb_loader folder.
+
+Load the SPL binary via USB:
 
-Load u-boot.imx via USB:
+$ sudo ./imx_usb SPL
 
-$ sudo ./imx_usb u-boot.imx
+Load the u-boot.img binary via USB:
+
+$ sudo ./imx_usb u-boot.img
 
 Then U-Boot should start and its messages will appear in the console program.
 
@@ -37,12 +47,16 @@ Use the default environment variables:
 => env default -f -a
 => saveenv
 
+2. Flashing U-Boot into the eMMC
+
 Run the DFU command:
 => dfu 0 mmc 0
 
-Transfer u-boot.imx that will be flashed into the eMMC:
+Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
+
+$ sudo dfu-util -D SPL -a spl
 
-$ sudo dfu-util -D u-boot.imx -a boot
+$ sudo dfu-util -D u-boot.img -a u-boot
 
 Then on the U-Boot prompt the following message should be seen after a
 successful upgrade:
Signature · 1 line
2.18.0
#17 lore raw

PATCH 8/13 pico-imx6ul: Sync defconfig with new changes

In reply to Otavio Salvador

Due the changes in previous commits, we need to resync the defconfig to reduce noise in next commits.

---

 configs/pico-imx6ul_defconfig | 20 ++++----------------
 1 file changed, 4 insertions(+), 16 deletions(-)
configs/pico-imx6ul_defconfig +4 -16
index daa898fb22..56cb4810dc 100644
@@ -9,43 +9,31 @@ CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL=y
 CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=1
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
 CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
+CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
+CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_SPL_I2C_SUPPORT=y
 CONFIG_SPL_USB_HOST_SUPPORT=y
 CONFIG_SPL_USB_GADGET_SUPPORT=y
 CONFIG_SPL_USB_SDP_SUPPORT=y
-CONFIG_BOOTDELAY=3
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_MEMTEST=y
 CONFIG_CMD_DFU=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y
-CONFIG_CMD_PART=y
 CONFIG_CMD_USB=y
 CONFIG_CMD_USB_SDP=y
 CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
 CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_DFU_MMC=y
 CONFIG_USB_FUNCTION_FASTBOOT=y
-CONFIG_FASTBOOT_BUF_ADDR=0x82000000
 CONFIG_FASTBOOT_BUF_SIZE=0x10000000
 CONFIG_FASTBOOT_FLASH=y
 CONFIG_FASTBOOT_FLASH_MMC_DEV=0
Signature · 1 line
2.18.0
#18 lore raw

PATCH 9/13 pico-imx6ul: Add bootmenu to choose the baseboard

In reply to Otavio Salvador

Currently the baseboards do not offer a way to autodetect which one is in use, so we ask the user if no value has been set.

---

 configs/pico-imx6ul_defconfig |  5 +++--
 include/configs/pico-imx6ul.h | 10 ++++++++++
 2 files changed, 13 insertions(+), 2 deletions(-)
configs/pico-imx6ul_defconfig +3 -2
index 56cb4810dc..3d4063b136 100644
@@ -13,13 +13,14 @@ CONFIG_DISTRO_DEFAULTS=y
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
 CONFIG_BOOTDELAY=3
-CONFIG_BOOTCOMMAND="run finduuid; run distro_bootcmd"
-CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
+CONFIG_BOOTCOMMAND="run findfdt; run finduuid; run distro_bootcmd"
+CONFIG_DEFAULT_FDT_FILE="ask"
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_SPL_I2C_SUPPORT=y
 CONFIG_SPL_USB_HOST_SUPPORT=y
 CONFIG_SPL_USB_GADGET_SUPPORT=y
 CONFIG_SPL_USB_SDP_SUPPORT=y
+CONFIG_CMD_BOOTMENU=y
 CONFIG_CMD_MEMTEST=y
 CONFIG_CMD_DFU=y
 # CONFIG_CMD_FLASH is not set
include/configs/pico-imx6ul.h +10 -0
index 14d5cc3ddb..2276f72bae 100644
@@ -50,6 +50,10 @@
 		"/imx6ul-pico-hobbit.dtb ext4 0 1;" \
 		"rootfs part 0 2\0" \
 
+#define BOOTMENU_ENV \
+	"bootmenu_0=Boot using PICO-Hobbit baseboard=" \
+		"setenv fdtfile imx6ul-pico-hobbit.dtb\0" \
+
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -59,6 +63,7 @@
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	BOOTMENU_ENV \
 	"fdt_addr=0x83000000\0" \
 	"fdt_addr_r=0x83000000\0" \
 	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
@@ -67,6 +72,11 @@
 	"ramdiskaddr=0x83000000\0" \
 	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
 	CONFIG_DFU_ENV_SETTINGS \
+	"findfdt=" \
+		"if test $fdtfile = ask ; then " \
+			"bootmenu -1; fi;" \
+		"if test $fdtfile != ask ; then " \
+			"saveenv; fi;\0" \
 	"finduuid=part uuid mmc 0:1 uuid\0" \
 	"partitions=" \
 		"uuid_disk=${uuid_gpt_disk};" \
Signature · 1 line
2.18.0
#19 lore raw

PATCH 10/13 pico-imx6ul: Improve default DFU settings

In reply to Otavio Salvador

This rework the DFU settings so it supports the SPL and U-Boot image, as well as the single partition layout we are using by default.

---

 include/configs/pico-imx6ul.h | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
include/configs/pico-imx6ul.h +6 -5
index 2276f72bae..a510fd1554 100644
@@ -44,11 +44,12 @@
 #define DFU_DEFAULT_POLL_TIMEOUT 300
 
 #define CONFIG_DFU_ENV_SETTINGS \
-	"dfu_alt_info=uboot raw 0x2 0x400 mmcpart 1;" \
-		"boot part 0 1;" \
-		"/zImage ext4 0 1;" \
-		"/imx6ul-pico-hobbit.dtb ext4 0 1;" \
-		"rootfs part 0 2\0" \
+	"dfu_alt_info=" \
+		"spl raw 0x2 0x400 mmcpart 1;" \
+		"u-boot raw 0x8a 0x400 mmcpart 1;" \
+		"/boot/zImage ext4 0 1;" \
+		"/boot/imx6ul-pico-hobbit.dtb ext4 0 1;" \
+		"rootfs part 0 1\0" \
 
 #define BOOTMENU_ENV \
 	"bootmenu_0=Boot using PICO-Hobbit baseboard=" \
Signature · 1 line
2.18.0
#20 lore raw

PATCH 11/13 pico-imx6ul: Sync README with pico-imx7d

In reply to Otavio Salvador

---

 board/technexion/pico-imx6ul/README | 22 +++++++++-------------
 1 file changed, 9 insertions(+), 13 deletions(-)
board/technexion/pico-imx6ul/README +9 -13
index a5415714ee..66dc977d49 100644
@@ -22,13 +22,14 @@ If the eMMC has already a U-Boot flashed with DFU support then
 the user can go to step 2 below in order to update U-Boot.
 
 Put pico board in USB download mode (refer to the document
-http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf page 15)
+http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf
+page 15).
 
-Connect a USB to serial adapter between the host PC and pico
+Connect a USB to serial adapter between the host PC and pico.
 
-Connect a USB cable between the OTG pico port and the host PC
+Connect a USB cable between the OTG pico port and the host PC.
 
-Open a terminal program such as minicom
+Open a terminal program such as minicom.
 
 Copy SPL and u-boot.img to the imx_usb_loader folder.
 
@@ -40,7 +41,7 @@ Load the u-boot.img binary via USB:
 
 $ sudo ./imx_usb u-boot.img
 
-Then U-Boot should start and its messages will appear in the console program.
+Then U-Boot starts and its messages appear in the console program.
 
 Use the default environment variables:
 
@@ -49,7 +50,8 @@ Use the default environment variables:
 
 2. Flashing U-Boot into the eMMC
 
-Run the DFU command:
+Run the DFU agent so we can flash the new images using dfu-util tool:
+
 => dfu 0 mmc 0
 
 Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
@@ -58,14 +60,8 @@ $ sudo dfu-util -D SPL -a spl
 
 $ sudo dfu-util -D u-boot.img -a u-boot
 
-Then on the U-Boot prompt the following message should be seen after a
-successful upgrade:
-
-#DOWNLOAD ... OK
-Ctrl+C to exit ...
-
 Remove power from the pico board.
 
-Put pico board into normal boot mode
+Put pico board into normal boot mode.
 
 Power up the board and the new updated U-Boot should boot from eMMC.
Signature · 1 line
2.18.0
#21 lore raw

PATCH 12/13 pico-imx6ul: Add new pico-hobbit config

In reply to Otavio Salvador

The new config skips the boot menu which asks which board is in use. This is useful to allow direct booting of image without user iteration.

---

 board/technexion/pico-imx6ul/MAINTAINERS |  5 +++
 configs/pico-hobbit-imx6ul_defconfig     | 53 ++++++++++++++++++++++++
 2 files changed, 58 insertions(+)
 create mode 100644 configs/pico-hobbit-imx6ul_defconfig
board/technexion/pico-imx6ul/MAINTAINERS +5 -0
index 594a883d15..334847cf71 100644
@@ -5,3 +5,8 @@ S:	Maintained
 F:	board/technexion/pico-imx6ul/
 F:	include/configs/pico-imx6ul.h
 F:	configs/pico-imx6ul_defconfig
+
+Technexion PICO-HOBBIT-IMX6UL
+M:	Otavio Salvador <[email protected]>
+S:	Maintained
+F:	configs/pico-hobbit-imx6ul_defconfig
configs/pico-hobbit-imx6ul_defconfig new file +53 -0

53 lines not on this page · raw message

Signature · 1 line
2.18.0
#22 lore raw

PATCH 13/13 pico-imx6ul: Remove CONFIG_FSL_USDHC from .h

In reply to Otavio Salvador

The FSL_USDHC support is now handled by Kconfig and it is enabled on the respective defconfig so the setting in .h is pointless.

---

 include/configs/pico-imx6ul.h | 1 -
 1 file changed, 1 deletion(-)
include/configs/pico-imx6ul.h +0 -1
index a510fd1554..94c14a7a43 100644
@@ -28,7 +28,6 @@
 #define CONFIG_MXC_UART_BASE		UART6_BASE_ADDR
 
 /* MMC Configs */
-#define CONFIG_FSL_USDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC1_BASE_ADDR
 #define CONFIG_SUPPORT_EMMC_BOOT
 
Signature · 1 line
2.18.0