MIPS: start.S: make boot config at offset 0x10 configurable
PATCH 1/1 MIPS: start.S: make boot config at offset 0x10 configurable
Some MIPS systems store some board-specific boot configuration in the U-Boot binary at offset 0x10. This is used by Malta boards and by Lantiq/Intel SoC's when booting from parallel NOR flash.
Convert the hard-coded values to Kconfig options to remove such board-specific stuff out of the generic start.S code. This also deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG.
Signed-off-by Daniel Schwierzeck <[email protected]>
---
README | 5 ----- arch/mips/Kconfig | 22 ++++++++++++++++++++++ arch/mips/cpu/start.S | 21 +++++---------------- scripts/config_whitelist.txt | 1 - 4 files changed, 27 insertions(+), 22 deletions(-)
README +0 -5
@@ -542,11 +542,6 @@ The following options need to be configured: CONF_CM_CACHABLE_CUW CONF_CM_CACHABLE_ACCELERATED - CONFIG_SYS_XWAY_EBU_BOOTCFG - - Special option for Lantiq XWAY SoCs for booting from NOR flash. - See also arch/mips/cpu/mips32/start.S. - CONFIG_XWAY_SWAP_BYTES Enable compilation of tools/xway-swap-bytes needed for Lantiq
arch/mips/Kconfig +22 -0
@@ -390,6 +390,28 @@ config MIPS_CM wish U-Boot to configure it or make use of it to retrieve system information such as cache configuration. +config MIPS_INSERT_BOOT_CONFIG + bool + default n + help + Enable this to insert some board-specific boot configuration in + the U-Boot binary at offset 0x10. + +config MIPS_BOOT_CONFIG_WORD0 + hex + depends on MIPS_INSERT_BOOT_CONFIG + default 0x420 if TARGET_MALTA + default 0x0 + help + Value which is inserted as boot config word 0. + +config MIPS_BOOT_CONFIG_WORD1 + hex + depends on MIPS_INSERT_BOOT_CONFIG + default 0x0 + help + Value which is inserted as boot config word 1. + endif endmenu
arch/mips/cpu/start.S +5 -16
@@ -84,25 +84,14 @@ ENTRY(_start) b reset mtc0 zero, CP0_COUNT # clear cp0 count for most accurate boot timing -#if defined(CONFIG_SYS_XWAY_EBU_BOOTCFG) +#if defined(CONFIG_MIPS_INSERT_BOOT_CONFIG) /* - * Almost all Lantiq XWAY SoC devices have an external bus unit (EBU) to - * access external NOR flashes. If the board boots from NOR flash the - * internal BootROM does a blind read at address 0xB0000010 to read the - * initial configuration for that EBU in order to access the flash - * device with correct parameters. This config option is board-specific. + * Store some board-specific boot configuration. This is used by some + * MIPS systems like Malta. */ .org 0x10 - .word CONFIG_SYS_XWAY_EBU_BOOTCFG - .word 0x0 -#endif -#if defined(CONFIG_MALTA) - /* - * Linux expects the Board ID here. - */ - .org 0x10 - .word 0x00000420 # 0x420 (Malta Board with CoreLV) - .word 0x00000000 + .word CONFIG_MIPS_BOOT_CONFIG_WORD0 + .word CONFIG_MIPS_BOOT_CONFIG_WORD1 #endif #if defined(CONFIG_ROM_EXCEPTION_VECTORS)
scripts/config_whitelist.txt +0 -1
@@ -4433,7 +4433,6 @@ CONFIG_SYS_XHCI_USB1_ADDR CONFIG_SYS_XHCI_USB2_ADDR CONFIG_SYS_XHCI_USB3_ADDR CONFIG_SYS_XIMG_LEN -CONFIG_SYS_XWAY_EBU_BOOTCFG CONFIG_SYS_ZYNQ_QSPI_WAIT CONFIG_SYS_ZYNQ_SPI_WAIT CONFIG_SYS_i2C_FSL
Signature · 1 line
2.18.0