Skip to contentSkip to conversation

ARM: meson: Use syscon/regmap for clock driver

RFC PATCH Superseded Loic Devulder 2 participants 5 messages Nov 2, 2018 – Nov 20, 2018

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover ARM: meson: Use syscon/regmap for clock driver

This patch series modifies the meson clock driver to use syscon/regmap like the Linux kernel does. It is needed if we want to share the same DTS files with the Linux kernel, as last changes in clock-controller break U-Boot.

I tried to keep compatibility with the old behaviour, if needed.

These patches also update all meson DTS files to last versions from Linux kernel v4.19.

It was successfully tested on kvim, kvim2 and libretech-cc, both with the old and new DTS files. I don't have any p212, nanopi-k2 nor odroid-c2 boards to test with. As kvim and libretech-cc boards share a lot with p212 I don't expect any issue with that board, but if someone is able to test on nanopo-k2 and odroid-c2 it could be great :-)

I opened this patch series as a RFC, as it's not a tricky part (for me!) and pretty new to me, so any feedback are welcome and wanted!

Loic Devulder (3):
ARM: meson: Add regmap support for clock driver
ARM: meson: Enable syscon on all supported boards
ARM: dts: meson: Update dts files from Linux v4.19

 arch/arm/dts/meson-gx.dtsi                    | 31 +++++++++++++----
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         | 48 ++++++++++++++++++++++++++
 arch/arm/dts/meson-gxbb.dtsi                  | 14 ++++----
 arch/arm/dts/meson-gxl-mali.dtsi              |  2 +-
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  5 +--
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        |  8 ++---
 arch/arm/dts/meson-gxl.dtsi                   | 26 ++++++--------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 24 +++++++++++++
 configs/khadas-vim2_defconfig                 |  1 +
 configs/khadas-vim_defconfig                  |  1 +
 configs/libretech-cc_defconfig                |  1 +
 configs/nanopi-k2_defconfig                   |  1 +
 configs/odroid-c2_defconfig                   |  1 +
 configs/p212_defconfig                        |  1 +
 drivers/clk/clk_meson.c                       | 49 +++++++++++++++------------
 15 files changed, 154 insertions(+), 59 deletions(-)
Signature · 1 line
2.16.4
#1 lore raw

RFC PATCH 1/3 ARM: meson: Add regmap support for clock driver

This patch modifies the meson clock driver to use syscon/regmap like the Linux kernel does, as it is needed if we want to share the same DTS files.
Compatibility is kept with the old behaviour, if needed.

---
 drivers/clk/clk_meson.c | 49 +++++++++++++++++++++++++++----------------------
 1 file changed, 27 insertions(+), 22 deletions(-)
drivers/clk/clk_meson.c +27 -22
index 236d7342b7..1cb3fde844 100644
@@ -12,6 +12,9 @@
 #include <div64.h>
 #include <dm.h>
 #include <dt-bindings/clock/gxbb-clkc.h>
+#include <regmap.h>
+#include <syscon.h>
+
 #include "clk_meson.h"
 
 /* This driver support only basic clock tree operations :
@@ -65,7 +68,7 @@
 #define XTAL_RATE 24000000
 
 struct meson_clk {
-	void __iomem *addr;
+	struct regmap *regmap;
 };
 
 static ulong meson_div_get_rate(struct clk *clk, unsigned long id);
@@ -217,7 +220,7 @@ static int meson_set_gate_by_id(struct clk *clk, unsigned long id, bool on)
 
 	debug("%s: really %sabling %ld\n", __func__, on ? "en" : "dis", id);
 
-	clrsetbits_le32(priv->addr + gate->reg,
+	clrsetbits_le32(priv->regmap->ranges[0].start + gate->reg,
 			BIT(gate->bit), on ? BIT(gate->bit) : 0);
 
 	/* Propagate to next gate(s) */
@@ -292,7 +295,7 @@ static ulong meson_div_get_rate(struct clk *clk, unsigned long id)
 		return -ENOENT;
 	}
 
-	reg = readl(priv->addr + parm->reg_off);
+	regmap_read(priv->regmap, parm->reg_off, &reg);
 	reg = PARM_GET(parm->width, parm->shift, reg);
 
 	debug("%s: div of %ld is %d\n", __func__, id, reg + 1);
@@ -318,7 +321,6 @@ static ulong meson_div_set_rate(struct clk *clk, unsigned long id, ulong rate,
 	unsigned long parent_rate;
 	struct parm *parm;
 	int parent;
-	u32 reg;
 	int ret;
 
 	if (current_rate == rate)
@@ -383,9 +385,8 @@ static ulong meson_div_set_rate(struct clk *clk, unsigned long id, ulong rate,
 
 	debug("%s: setting div of %ld to %d\n", __func__, id, new_div);
 
-	reg = readl(priv->addr + parm->reg_off);
-	writel(PARM_SET(parm->width, parm->shift, reg, new_div - 1),
-	       priv->addr + parm->reg_off);
+	regmap_update_bits(priv->regmap, parm->reg_off, SETPMASK(parm->width, parm->shift),
+			   (new_div - 1) << parm->shift);
 
 	debug("%s: new rate of %ld is %ld\n",
 	      __func__, id, meson_div_get_rate(clk, id));
@@ -477,7 +478,7 @@ static ulong meson_mux_get_parent(struct clk *clk, unsigned long id)
 		return -ENOENT;
 	}
 
-	reg = readl(priv->addr + parm->reg_off);
+	regmap_read(priv->regmap, parm->reg_off, &reg);
 	reg = PARM_GET(parm->width, parm->shift, reg);
 
 	debug("%s: parent of %ld is %d (%d)\n",
@@ -494,7 +495,6 @@ static ulong meson_mux_set_parent(struct clk *clk, unsigned long id,
 	unsigned int new_index = -EINVAL;
 	struct parm *parm;
 	int *parents;
-	u32 reg;
 	int i;
 
 	if (IS_ERR_VALUE(cur_parent))
@@ -546,9 +546,8 @@ static ulong meson_mux_set_parent(struct clk *clk, unsigned long id,
 
 	debug("%s: new index of %ld is %d\n", __func__, id, new_index);
 
-	reg = readl(priv->addr + parm->reg_off);
-	writel(PARM_SET(parm->width, parm->shift, reg, new_index),
-	       priv->addr + parm->reg_off);
+	regmap_update_bits(priv->regmap, parm->reg_off, SETPMASK(parm->width, parm->shift),
+			   new_index << parm->shift);
 
 	debug("%s: new parent of %ld is %ld\n",
 	      __func__, id, meson_mux_get_parent(clk, id));
@@ -583,7 +582,7 @@ static unsigned long meson_clk81_get_rate(struct clk *clk)
 	};
 
 	/* mux */
-	reg = readl(priv->addr + HHI_MPEG_CLK_CNTL);
+	regmap_read(priv->regmap, HHI_MPEG_CLK_CNTL, &reg);
 	reg = (reg >> 12) & 7;
 
 	switch (reg) {
@@ -597,7 +596,7 @@ static unsigned long meson_clk81_get_rate(struct clk *clk)
 	}
 
 	/* divider */
-	reg = readl(priv->addr + HHI_MPEG_CLK_CNTL);
+	regmap_read(priv->regmap, HHI_MPEG_CLK_CNTL, &reg);
 	reg = reg & ((1 << 7) - 1);
 
 	return parent_rate / reg;
@@ -640,8 +639,9 @@ static ulong meson_mpll_get_rate(struct clk *clk, unsigned long id)
 {
 	struct meson_clk *priv = dev_get_priv(clk->dev);
 	struct parm *psdm, *pn2;
-	unsigned long reg, sdm, n2;
+	unsigned long sdm, n2;
 	unsigned long parent_rate;
+	u32 reg;
 
 	switch (id) {
 	case CLKID_MPLL0:
@@ -664,10 +664,10 @@ static ulong meson_mpll_get_rate(struct clk *clk, unsigned long id)
 	if (IS_ERR_VALUE(parent_rate))
 		return parent_rate;
 
-	reg = readl(priv->addr + psdm->reg_off);
+	regmap_read(priv->regmap, psdm->reg_off, &reg);
 	sdm = PARM_GET(psdm->width, psdm->shift, reg);
 
-	reg = readl(priv->addr + pn2->reg_off);
+	regmap_read(priv->regmap, pn2->reg_off, &reg);
 	n2 = PARM_GET(pn2->width, pn2->shift, reg);
 
 	return mpll_rate_from_params(parent_rate, sdm, n2);
@@ -708,13 +708,13 @@ static ulong meson_pll_get_rate(struct clk *clk, unsigned long id)
 		return -ENOENT;
 	}
 
-	reg = readl(priv->addr + pn->reg_off);
+	regmap_read(priv->regmap, pn->reg_off, &reg);
 	n = PARM_GET(pn->width, pn->shift, reg);
 
-	reg = readl(priv->addr + pm->reg_off);
+	regmap_read(priv->regmap, pm->reg_off, &reg);
 	m = PARM_GET(pm->width, pm->shift, reg);
 
-	reg = readl(priv->addr + pod->reg_off);
+	regmap_read(priv->regmap, pod->reg_off, &reg);
 	od = PARM_GET(pod->width, pod->shift, reg);
 
 	return ((parent_rate_mhz * m / n) >> od) * 1000000;
@@ -885,9 +885,14 @@ static int meson_clk_probe(struct udevice *dev)
 {
 	struct meson_clk *priv = dev_get_priv(dev);
 
-	priv->addr = dev_read_addr_ptr(dev);
+	priv->regmap = syscon_node_to_regmap(dev_get_parent(dev)->node);
+	if (IS_ERR(priv->regmap)) {
+		debug("failed to get regmap from parent, trying regs");
 
-	debug("meson-clk: probed at addr %p\n", priv->addr);
+		regmap_init_mem(dev_ofnode(dev), &priv->regmap);
+		if (IS_ERR(priv->regmap))
+			return PTR_ERR(priv->regmap);
+	}
 
 	return 0;
 }
Signature · 1 line
2.16.4
#2 lore raw

RFC PATCH 2/3 ARM: meson: Enable syscon on all supported boards

In reply to Loic Devulder

This patch enable CONFIG_SYSCON option on all supported meson boards, as this is need for the new clock driver to work.

---
 configs/khadas-vim2_defconfig  | 1 +
 configs/khadas-vim_defconfig   | 1 +
 configs/libretech-cc_defconfig | 1 +
 configs/nanopi-k2_defconfig    | 1 +
 configs/odroid-c2_defconfig    | 1 +
 configs/p212_defconfig         | 1 +
 6 files changed, 6 insertions(+)
configs/khadas-vim2_defconfig +1 -0
index f21e3a8ddf..c5f2b3f111 100644
@@ -49,3 +49,4 @@ CONFIG_USB_STORAGE=y
 CONFIG_PHY=y
 CONFIG_MESON_GXL_USB_PHY=y
 CONFIG_MTD=y
+CONFIG_SYSCON=y
configs/khadas-vim_defconfig +1 -0
index 0c89d9a22c..6815c7bebf 100644
@@ -51,3 +51,4 @@ CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_STORAGE=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYSCON=y
configs/libretech-cc_defconfig +1 -0
index 36d117c4ab..4267d75931 100644
@@ -51,3 +51,4 @@ CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_STORAGE=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYSCON=y
configs/nanopi-k2_defconfig +1 -0
index 5c8c747bf3..7222419e84 100644
@@ -40,3 +40,4 @@ CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_DEBUG_UART_SKIP_INIT=y
 CONFIG_MESON_SERIAL=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYSCON=y
configs/odroid-c2_defconfig +1 -0
index 19196b3585..3ad4f73a85 100644
@@ -40,3 +40,4 @@ CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_DEBUG_UART_SKIP_INIT=y
 CONFIG_MESON_SERIAL=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYSCON=y
configs/p212_defconfig +1 -0
index 9e3b1d6bfb..9bbe67ac61 100644
@@ -50,3 +50,4 @@ CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_STORAGE=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SYSCON=y
Signature · 1 line
2.16.4
#3 lore raw

RFC PATCH 3/3 ARM: dts: meson: Update dts files from Linux v4.19

In reply to Loic Devulder

This patch modifies Device Tree of meson boards.

The dts files are synchronized from Linux 4.19.

---
 arch/arm/dts/meson-gx.dtsi                    | 31 +++++++++++++----
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         | 48 +++++++++++++++++++++++++++
 arch/arm/dts/meson-gxbb.dtsi                  | 14 ++++----
 arch/arm/dts/meson-gxl-mali.dtsi              |  2 +-
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  5 +--
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        |  8 ++---
 arch/arm/dts/meson-gxl.dtsi                   | 26 ++++++---------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 24 ++++++++++++++
 8 files changed, 121 insertions(+), 37 deletions(-)
arch/arm/dts/meson-gx.dtsi +25 -6
index 3c31e21cbe..f1e5cdbade 100644
@@ -35,10 +35,16 @@
 			no-map;
 		};
 
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved_alt: secmon at 5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
-			size = <0x0 0xbc00000>;
+			size = <0x0 0x10000000>;
 			alignment = <0x0 0x400000>;
 			linux,cma-default;
 		};
@@ -338,7 +344,7 @@
 			ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
 
 			sysctrl_AO: sys-ctrl at 0 {
-				compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd";
+				compatible = "amlogic,meson-gx-ao-sysctrl", "simple-mfd", "syscon";
 				reg =  <0x0 0x0 0x0 0x100>;
 
 				pwrc_vpu: power-controller-vpu {
@@ -417,6 +423,19 @@
 			};
 		};
 
+		dmcbus: bus at c8838000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xc8838000 0x0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xc8838000 0x0 0x400>;
+
+			canvas: video-lut at 48 {
+				compatible = "amlogic,canvas";
+				reg = <0x0 0x48 0x0 0x14>;
+			};
+		};
+
 		hiubus: bus at c883c000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xc883c000 0x0 0x2000>;
@@ -425,7 +444,7 @@
 			ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
 
 			sysctrl: system-controller at 0 {
-				compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd";
+				compatible = "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon";
 				reg = <0 0 0 0x400>;
 			};
 
@@ -457,21 +476,21 @@
 
 			sd_emmc_a: mmc at 70000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x70000 0x0 0x2000>;
+				reg = <0x0 0x70000 0x0 0x800>;
 				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_b: mmc at 72000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x72000 0x0 0x2000>;
+				reg = <0x0 0x72000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_c: mmc at 74000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x74000 0x0 0x2000>;
+				reg = <0x0 0x74000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
arch/arm/dts/meson-gxbb-nanopi-k2.dts +48 -0

60 lines not on this page · raw message

arch/arm/dts/meson-gxbb.dtsi +8 -6
index 562c26a0ba..1ade7e4868 100644
@@ -307,11 +307,10 @@
 	clock-names = "isfr", "iahb", "venci";
 };
 
-&hiubus {
-	clkc: clock-controller at 0 {
+&sysctrl {
+	clkc: clock-controller {
 		compatible = "amlogic,gxbb-clkc";
 		#clock-cells = <1>;
-		reg = <0x0 0x0 0x0 0x3db>;
 	};
 };
 
@@ -391,7 +390,7 @@
 			};
 		};
 
-		spi_pins: spi {
+		spi_pins: spi-pins {
 			mux {
 				groups = "spi_miso",
 					"spi_mosi",
@@ -716,6 +715,7 @@
 		 <&clkc CLKID_SD_EMMC_A_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
 	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_A>;
 };
 
 &sd_emmc_b {
@@ -723,6 +723,7 @@
 		 <&clkc CLKID_SD_EMMC_B_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
 	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_B>;
 };
 
 &sd_emmc_c {
@@ -730,6 +731,7 @@
 		 <&clkc CLKID_SD_EMMC_C_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
 	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_C>;
 };
 
 &spicc {
@@ -749,12 +751,12 @@
 };
 
 &uart_AO {
-	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART1>, <&xtal>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_AO_B {
-	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
arch/arm/dts/meson-gxl-mali.dtsi +1 -1
index eb327664a4..6aaafff674 100644
@@ -6,7 +6,7 @@
 
 &apb {
 	mali: gpu at c0000 {
-		compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+		compatible = "amlogic,meson-gxl-mali", "arm,mali-450";
 		reg = <0x0 0xc0000 0x0 0x40000>;
 		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
arch/arm/dts/meson-gxl-s905x-libretech-cc.dts +1 -4
index 3e3eb31748..90a56af967 100644
@@ -13,7 +13,7 @@
 
 / {
 	compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
-	model = "Libre Technology CC";
+	model = "Libre Computer Board AML-S905X-CC";
 
 	aliases {
 		serial0 = &uart_AO;
@@ -234,9 +234,6 @@
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
 	max-frequency = <100000000>;
 	disable-wp;
 
arch/arm/dts/meson-gxl-s905x-p212.dtsi +4 -4
index 3bd405079b..a1b31013ab 100644
@@ -191,8 +191,8 @@
 };
 
 &usb2_phy0 {
-        /*
-         * HDMI_5V is also used as supply for the USB VBUS.
-         */
-        phy-supply = <&hdmi_5v>;
+	/*
+	 * HDMI_5V is also used as supply for the USB VBUS.
+	 */
+	phy-supply = <&hdmi_5v>;
 };
arch/arm/dts/meson-gxl.dtsi +10 -16
index dba365ed4b..8f0bb3c44b 100644
@@ -13,14 +13,6 @@
 / {
 	compatible = "amlogic,meson-gxl";
 
-	reserved-memory {
-		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
-		secmon_reserved_alt: secmon at 5000000 {
-			reg = <0x0 0x05000000 0x0 0x300000>;
-			no-map;
-		};
-	};
-
 	soc {
 		usb0: usb at c9000000 {
 			status = "disabled";
@@ -267,11 +259,10 @@
 	clock-names = "isfr", "iahb", "venci";
 };
 
-&hiubus {
-	clkc: clock-controller at 0 {
-		compatible = "amlogic,gxl-clkc", "amlogic,gxbb-clkc";
+&sysctrl {
+	clkc: clock-controller {
+		compatible = "amlogic,gxl-clkc";
 		#clock-cells = <1>;
-		reg = <0x0 0x0 0x0 0x3db>;
 	};
 };
 
@@ -346,7 +337,7 @@
 			};
 		};
 
-		spi_pins: spi {
+		spi_pins: spi-pins {
 			mux {
 				groups = "spi_miso",
 					"spi_mosi",
@@ -725,13 +716,15 @@
 		 <&clkc CLKID_SD_EMMC_A_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
 	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_A>;
 };
 
 &sd_emmc_b {
 	clocks = <&clkc CLKID_SD_EMMC_B>,
 		 <&clkc CLKID_SD_EMMC_B_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
-       clock-names = "core", "clkin0", "clkin1";
+	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_B>;
 };
 
 &sd_emmc_c {
@@ -739,6 +732,7 @@
 		 <&clkc CLKID_SD_EMMC_C_CLK0>,
 		 <&clkc CLKID_FCLK_DIV2>;
 	clock-names = "core", "clkin0", "clkin1";
+	resets = <&reset RESET_SD_EMMC_C>;
 };
 
 &spicc {
@@ -758,12 +752,12 @@
 };
 
 &uart_AO {
-	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART1>, <&xtal>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_AO_B {
-	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
arch/arm/dts/meson-gxm-khadas-vim2.dts +24 -0
index 0868da476e..313f88f875 100644
@@ -209,10 +209,34 @@
 	#cooling-cells = <2>;
 };
 
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
+
 &cpu4 {
 	#cooling-cells = <2>;
 };
 
+&cpu5 {
+	#cooling-cells = <2>;
+};
+
+&cpu6 {
+	#cooling-cells = <2>;
+};
+
+&cpu7 {
+	#cooling-cells = <2>;
+};
+
 &ethmac {
 	pinctrl-0 = <&eth_pins>;
 	pinctrl-names = "default";
Signature · 1 line
2.16.4
#4 lore raw

cover ARM: meson: Use syscon/regmap for clock driver

In reply to Loic Devulder

Hi Loic,

I totally missed this patchset....

It looks ok, can you rebase it on top of the huge "Amlogic Meson cleanup for AXG SoC support" patchset ?

You can remove the RFC tag I think.

Thanks,
Neil

Quoted 41 lines · Loic Devulder

This patch series modifies the meson clock driver to use syscon/regmap like the Linux kernel does. It is needed if we want to share the same DTS files with the Linux kernel, as last changes in clock-controller break U-Boot.

I tried to keep compatibility with the old behaviour, if needed.

These patches also update all meson DTS files to last versions from Linux kernel v4.19.

It was successfully tested on kvim, kvim2 and libretech-cc, both with the old and new DTS files. I don't have any p212, nanopi-k2 nor odroid-c2 boards to test with. As kvim and libretech-cc boards share a lot with p212 I don't expect any issue with that board, but if someone is able to test on nanopo-k2 and odroid-c2 it could be great :-)

I opened this patch series as a RFC, as it's not a tricky part (for me!) and pretty new to me, so any feedback are welcome and wanted!

Loic Devulder (3):
ARM: meson: Add regmap support for clock driver
ARM: meson: Enable syscon on all supported boards
ARM: dts: meson: Update dts files from Linux v4.19

 arch/arm/dts/meson-gx.dtsi                    | 31 +++++++++++++----
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         | 48 ++++++++++++++++++++++++++
 arch/arm/dts/meson-gxbb.dtsi                  | 14 ++++----
 arch/arm/dts/meson-gxl-mali.dtsi              |  2 +-
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  5 +--
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        |  8 ++---
 arch/arm/dts/meson-gxl.dtsi                   | 26 ++++++--------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 24 +++++++++++++
 configs/khadas-vim2_defconfig                 |  1 +
 configs/khadas-vim_defconfig                  |  1 +
 configs/libretech-cc_defconfig                |  1 +
 configs/nanopi-k2_defconfig                   |  1 +
 configs/odroid-c2_defconfig                   |  1 +
 configs/p212_defconfig                        |  1 +
 drivers/clk/clk_meson.c                       | 49 +++++++++++++++------------
 15 files changed, 154 insertions(+), 59 deletions(-)