FSL QSPI device tree cleanup for 4.21
Subsystems (2)
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Shawn
The following changes since commit 744284fa15a1acc8601ddc0a349678e033100925:
Merge tag 'imx-dt64-4.21' into imx/qspi-dt (2018-12-16 16:20:47 +0800)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git tags/imx-qspi-dt-clean
for you to fetch changes up to 30648e9f864774388d261f42e79955362f4739e7:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller (2018-12-16 16:24:01 +0800)
----------------------------------------------------------------
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI device tree nodes. The current device trees are broken because they use an inconsistent scheme for assigning the reg properties. It becomes a problem with ongoing QSPI driver under SPI framework. So the cleanup is a preparation for new driver landing in the next cycle.
----------------------------------------------------------------
Frieder Schrempf (5):
ARM: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arch/arm/boot/dts/imx6sx-sdb-reva.dts | 8 ++++++-- arch/arm/boot/dts/imx6sx-sdb.dts | 8 ++++++-- arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 ++ arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts | 5 ++--- arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts | 3 ++- arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 4 ++-- arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 6 ++++-- arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi | 4 ++++ 8 files changed, 28 insertions(+), 12 deletions(-)
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 9 lines · Shawn Guo
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Thanks,
Arnd
Hi Arnd,
Quoted 11 lines · Arnd Bergmann
Quoted 9 lines · Shawn Guo
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Quoted 4 lines
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Thanks for pulling these late changes. The old SPI NOR driver (fsl-quadspi.c) will be replaced by the new SPI driver. Old dtb files will work with the new driver if they already have the reg properties set up correctly (which should be the case, but who knows what setups exist out-of-tree).
There will be a performance penalty though if you do not set spi-[tx/rx]-bus-width to 4.
For reference here is the latest set of patches:
https://patchwork.ozlabs.org/cover/1007641/
Thanks,
Frieder
Quoted 20 lines · Schrempf Frieder
Hi Arnd,
Quoted 11 lines · Arnd Bergmann
Quoted 9 lines · Shawn Guo
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Quoted 4 lines
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Quoted 5 lines
Thanks for pulling these late changes. The old SPI NOR driver (
fsl-quadspi.c) will be replaced by the new SPI driver. Old dtb files will work with the new driver if they already have the reg properties set up correctly (which should be the case, but who knows what setups exist out-of-tree).
Ok, good.
Quoted 2 lines
There will be a performance penalty though if you do not set spi-[tx/rx]-bus-width to 4.
I guess that's acceptable, but what is the reason for requiring this? Would it be possible to have the qspi driver add those properties and print a warning whenever the dtb doesn't already contain them?
Arnd
Quoted 30 lines · Arnd Bergmann
Quoted 20 lines · Schrempf Frieder
Hi Arnd,
Quoted 11 lines · Arnd Bergmann
Quoted 9 lines · Shawn Guo
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Quoted 4 lines
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Quoted 5 lines
Thanks for pulling these late changes. The old SPI NOR driver (
fsl-quadspi.c) will be replaced by the new SPI driver. Old dtb files will work with the new driver if they already have the reg properties set up correctly (which should be the case, but who knows what setups exist out-of-tree).Ok, good.
Quoted 7 lines
Quoted 2 lines
There will be a performance penalty though if you do not set spi-[tx/rx]-bus-width to 4.
I guess that's acceptable, but what is the reason for requiring this? Would it be possible to have the qspi driver add those properties and print a warning whenever the dtb doesn't already contain them?
As the new driver is a SPI driver, the common rules in Documentation/devicetree/bindings/spi/spi-bus.txt apply and spi-[tx/rx]-bus-width are defined to default to 1 if not specified. So we can't set those properties in the driver if they are missing in the dtb as we would deviate from the standard, although it would make more sense for a *Quad*-SPI driver to default to 4.
Quoted 40 lines · Schrempf Frieder
Quoted 30 lines · Arnd Bergmann
Quoted 20 lines · Schrempf Frieder
Hi Arnd,
Quoted 11 lines · Arnd Bergmann
Quoted 9 lines · Shawn Guo
Hi,
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Quoted 4 lines
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Quoted 5 lines
Thanks for pulling these late changes. The old SPI NOR driver (
fsl-quadspi.c) will be replaced by the new SPI driver. Old dtb files will work with the new driver if they already have the reg properties set up correctly (which should be the case, but who knows what setups exist out-of-tree).Ok, good.
Quoted 7 lines
Quoted 2 lines
There will be a performance penalty though if you do not set spi-[tx/rx]-bus-width to 4.
I guess that's acceptable, but what is the reason for requiring this? Would it be possible to have the qspi driver add those properties and print a warning whenever the dtb doesn't already contain them?
Quoted 6 lines
As the new driver is a SPI driver, the common rules in
Documentation/devicetree/bindings/spi/spi-bus.txtapply and spi-[tx/rx]-bus-width are defined to default to 1 if not specified. So we can't set those properties in the driver if they are missing in the dtb as we would deviate from the standard, although it would make more sense for a *Quad*-SPI driver to default to 4.
Right, I guess that makes sense.
Now, you could change the binding for the fsl-quadspi driver to require the bus-width properties, which would then just make the old dtb files invalid, and you give us an excuse to override the properties by adding the =4 ones, once that is documented in the driver specific binding.
Since it's only a performance difference, I suppose we can live with the limitation and stay a little closer to the normal binding.
Arnd
Hi Arnd,
Quoted 45 lines · Arnd Bergmann
Quoted 34 lines · Schrempf Frieder
Quoted 25 lines · Arnd Bergmann
Quoted 15 lines · Schrempf Frieder
Quoted 8 lines · Arnd Bergmann
Quoted 6 lines · Shawn Guo
As the series cleans up both i.MX/Freescale arm32 and arm64 device trees, the pull request is based on a merge of tag imx-dt-4.21 and imx-dt64-4.21 that have already been pulled into arm-soc next/dt branch. This comes a bit late, and we appreciate it if you can pull it for 4.21, as it paves the way for new QSPI driver under SPI framework to land in the next release cycle. Thanks.
Quoted 4 lines
Pulled into next/dt. For my understanding, what is going to happen with the fsl-quadspi mtd driver? Will it remain as part of the kernel to support old DTB files, or will that transitions mean those stop working with new kernels and have to be updated the same way?
Quoted 5 lines
Thanks for pulling these late changes. The old SPI NOR driver (
fsl-quadspi.c) will be replaced by the new SPI driver. Old dtb files will work with the new driver if they already have the reg properties set up correctly (which should be the case, but who knows what setups exist out-of-tree).Ok, good.
Quoted 7 lines
Quoted 2 lines
There will be a performance penalty though if you do not set spi-[tx/rx]-bus-width to 4.
I guess that's acceptable, but what is the reason for requiring this? Would it be possible to have the qspi driver add those properties and print a warning whenever the dtb doesn't already contain them?
Quoted 6 lines
As the new driver is a SPI driver, the common rules in
Documentation/devicetree/bindings/spi/spi-bus.txtapply and spi-[tx/rx]-bus-width are defined to default to 1 if not specified. So we can't set those properties in the driver if they are missing in the dtb as we would deviate from the standard, although it would make more sense for a *Quad*-SPI driver to default to 4.Right, I guess that makes sense.
Quoted 8 lines
Now, you could change the binding for the fsl-quadspi driver to require the bus-width properties, which would then just make the old dtb files invalid, and you give us an excuse to override the properties by adding the =4 ones, once that is documented in the driver specific binding.
Since it's only a performance difference, I suppose we can live with the limitation and stay a little closer to the normal binding.
Please note that a quad-capable SPI FLASH may be physically wired to a quad-capable SPI controller using only 2 wires, so defaulting to 4 may cause issues. Defaulting to 2 may work, if the device is dual-capable.
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Quoted 17 lines · Geert Uytterhoeven
Quoted 16 lines · Arnd Bergmann
On Thu, Dec 20, 2018 at 5:23 PM Schrempf Frieder
Quoted 6 lines
As the new driver is a SPI driver, the common rules in
Documentation/devicetree/bindings/spi/spi-bus.txtapply and spi-[tx/rx]-bus-width are defined to default to 1 if not specified. So we can't set those properties in the driver if they are missing in the dtb as we would deviate from the standard, although it would make more sense for a *Quad*-SPI driver to default to 4.Right, I guess that makes sense.
Now, you could change the binding for the fsl-quadspi driver to require the bus-width properties, which would then just make the old dtb files invalid, and you give us an excuse to override the properties by adding the =4 ones, once that is documented in the driver specific binding.
Quoted 7 lines
Quoted 2 lines
Since it's only a performance difference, I suppose we can live with the limitation and stay a little closer to the normal binding.
Please note that a quad-capable SPI FLASH may be physically wired to a quad-capable SPI controller using only 2 wires, so defaulting to 4 may cause issues. Defaulting to 2 may work, if the device is dual-capable.
Right, this would only work because the old driver used 4 wires in the absence of the DT property, and the driver would warn when it's not there for new dtb files.
Arnd