Skip to contentSkip to conversation

ASoC: sgtl5000: Allow SCLK pad drive strength to be changed

PATCH Superseded Alison Wang 1 participant 1 message Dec 24, 2018

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ASoC: sgtl5000: Allow SCLK pad drive strength to be changed

This patch introduces "sclk-strength" property to allow SCLK pad drive strength to be changed via device tree.

When running playback test on LS1028ARDB, Tx Frame sync error interrupt will occur sometimes. Some noises also exist. After changing SCLK pad drive strength to the maximum value, the issues are gone.

---
 sound/soc/codecs/sgtl5000.c |   19 ++++++++++++++++++-
 1 files changed, 18 insertions(+), 1 deletions(-)
sound/soc/codecs/sgtl5000.c +18 -1
index add18d6..a6a4748 100644
@@ -116,6 +116,13 @@ enum  {
 	I2S_LRCLK_STRENGTH_HIGH,
 };
 
+enum  {
+	I2S_SCLK_STRENGTH_DISABLE,
+	I2S_SCLK_STRENGTH_LOW,
+	I2S_SCLK_STRENGTH_MEDIUM,
+	I2S_SCLK_STRENGTH_HIGH,
+};
+
 /* sgtl5000 private structure in codec */
 struct sgtl5000_priv {
 	int sysclk;	/* sysclk rate */
@@ -129,6 +136,7 @@ struct sgtl5000_priv {
 	u8 micbias_resistor;
 	u8 micbias_voltage;
 	u8 lrclk_strength;
+	u8 sclk_strength;
 };
 
 /*
@@ -1302,7 +1310,9 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 			SGTL5000_DAC_MUTE_RIGHT |
 			SGTL5000_DAC_MUTE_LEFT);
 
-	reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT | 0x5f);
+	reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT |
+	       (sgtl5000->sclk_strength) << SGTL5000_PAD_I2S_SCLK_SHIFT |
+	       0x1f);
 	snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);
 
 	snd_soc_component_write(component, SGTL5000_CHIP_ANA_CTRL,
@@ -1542,6 +1552,13 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
 		sgtl5000->lrclk_strength = value;
 	}
 
+	sgtl5000->sclk_strength = I2S_SCLK_STRENGTH_LOW;
+	if (!of_property_read_u32(np, "sclk-strength", &value)) {
+		if (value > I2S_SCLK_STRENGTH_HIGH)
+			value = I2S_SCLK_STRENGTH_LOW;
+		sgtl5000->sclk_strength = value;
+	}
+
 	/* Ensure sgtl5000 will start with sane register values */
 	sgtl5000_fill_defaults(client);
 
Signature · 1 line
1.7.1