Skip to contentSkip to conversation

ir-ctl: Rename no-wideband to narrowband

PATCH New Sean Young 1 participant 2 messages Jan 16, 2019 Media (V4L/DVB)

lore
Share & tools
lore

Sean Young

author
#0 lore raw

PATCH 1/2 ir-ctl: Rename no-wideband to narrowband

Signed-off-by Sean Young <[email protected]>
---
 utils/ir-ctl/ir-ctl.1.in | 2 +-
 utils/ir-ctl/ir-ctl.c    | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
utils/ir-ctl/ir-ctl.1.in +1 -1
index 2a148c70..10d4d594 100644
@@ -54,7 +54,7 @@ Use the wideband receiver if available on the hardware. This is also
 known as learning mode. The measurements should be more precise and any
 carrier frequency should be accepted.
 .TP
-\fB\-n\fR, \fB\-\-no-wideband\fR
+\fB\-n\fR, \fB\-\-narrowband\fR
 Switches back to the normal, narrowband receiver if the wideband receiver
 was enabled.
 .TP
utils/ir-ctl/ir-ctl.c +1 -1
index ddd93068..dcc9439c 100644
@@ -109,7 +109,7 @@ static const struct argp_option options[] = {
 		{ .doc = N_("Receiving options:") },
 	{ "one-shot",	'1',	0,		0,	N_("end receiving after first message") },
 	{ "wideband",	'w',	0,		0,	N_("use wideband receiver aka learning mode") },
-	{ "no-wideband",'n',	0,		0,	N_("use normal narrowband receiver, disable learning mode") },
+	{ "narrowband",'n',	0,		0,	N_("use narrowband receiver, disable learning mode") },
 	{ "carrier-range", 'R', N_("RANGE"),	0,	N_("set receiver carrier range") },
 	{ "measure-carrier", 'm', 0,		0,	N_("report carrier frequency") },
 	{ "no-measure-carrier", 'M', 0,		0,	N_("disable reporting carrier frequency") },
Signature · 1 line
2.20.1
author
#1 lore raw

PATCH 2/2 ir-ctl: imon protocol can be encoded too

Signed-off-by Sean Young <[email protected]>
---
 utils/ir-ctl/ir-ctl.1.in | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
utils/ir-ctl/ir-ctl.1.in +1 -1
index 10d4d594..226bf606 100644
@@ -181,7 +181,7 @@ pulse and space file. The following protocols are supported:
 \fBrc5\fR, \fBrc5x_20\fR, \fBrc5_sz\fR, \fBjvc\fR, \fBsony12\fR,
 \fBsony\fB15\fR, \fBsony20\fR, \fBnec\fR, \fBnecx\fR, \fBnec32\fR,
 \fBsanyo\fR, \fBrc6_0\fR, \fBrc6_6a_20\fR, \fBrc6_6a_24\fR, \fBrc6_6a_32\fR,
-\fBrc6_mce\fR, \fBsharp\fR.
+\fBrc6_mce\fR, \fBsharp\fR, \fBimon\fR.
 If the scancode starts with 0x it will be interpreted as a
 hexadecimal number, and if it starts with 0 it will be interpreted as an
 octal number.
Signature · 1 line
2.20.1