Skip to contentSkip to conversation

media: ov5640: JPEG and test pattern improvements

PATCH In review Chen-Yu Tsai 2 participants 10 messages Jan 18, 2019 – Feb 5, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover media: ov5640: JPEG and test pattern improvements

Hi everyone,

This series improves the JPEG compression output mode handling of the OV5640 sensor, and adds some more test patterns for users to use.

The JPEG compression output mode of the sensor works, but the data framing is incorrect. Additional registers need to be set to configure the framing / timing of the data. This was found when adding support for JPEG_1X8 for the sun6i CSI sensor interface driver (improvements which I'll send in a separate series). Because the default timings might not be the same as the resolution timings, the capture device would either truncate or pad each line as it is captured. This corrupts the JPEG data. With the timings fixed, the captured data is once again a continuous JPEG file.

While using the test pattern for testing, I found that the test pattern was superimposed on top of an actual captured image. This made it slightly harder to compare results, as the underlying image would change with scenery and static from the sensor. Disabling the transparency feature makes the result a "true" test pattern.

I also added the "rolling bar" variant of the color bar test pattern, which is much better for testing video captures, as the image changes in a predictable way, instead of being static.

Finally, another test pattern, "color squares", along with a rolling bar variant, were added as an alternative.

Patch 1 is some simple code movement, in preparation for the next patch.

Patch 2 adds definitions for the test pattern configuration register, to be used in the next patch.

Patch 3 disables the transparency feature of the test pattern generator.

Patch 4 adds more test pattern options.

Patch 5 fixes the JPEG compression output data framing.

Patch 6 consolidates the JPEG compression mode setting in one place, instead of being listed in the register dumps.

Please have a look.

Regards
ChenYu

Chen-Yu Tsai (6):
media: ov5640: Move test_pattern_menu before

    ov5640_set_ctrl_test_pattern

media: ov5640: Add register definition for test pattern register
media: ov5640: Disable transparent feature for test pattern
media: ov5640: Add three more test patterns
media: ov5640: Set JPEG output timings when outputting JPEG data
media: ov5640: Consolidate JPEG compression mode setting

 drivers/media/i2c/ov5640.c | 95 ++++++++++++++++++++++++++++++--------
 1 file changed, 77 insertions(+), 18 deletions(-)
Signature · 1 line
2.20.1
#1 lore raw

PATCH 1/6 media: ov5640: Move test_pattern_menu before ov5640_set_ctrl_test_pattern

The OV5640 has many options for generating test patterns. Unfortunately there is only one V4L2 control for it. Thus the driver would need to list some or all combinations.

Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern function that programs the hardware. This would allow us to add a matching list of values to program into the hardware, while keeping the two lists together for ease of maintenance.

---
 drivers/media/i2c/ov5640.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/media/i2c/ov5640.c +5 -5
index 5a909abd0a2d..8e4e8fa3685f 100644
@@ -2441,6 +2441,11 @@ static int ov5640_set_ctrl_gain(struct ov5640_dev *sensor, bool auto_gain)
 	return ret;
 }
 
+static const char * const test_pattern_menu[] = {
+	"Disabled",
+	"Color bars",
+};
+
 static int ov5640_set_ctrl_test_pattern(struct ov5640_dev *sensor, int value)
 {
 	return ov5640_mod_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
@@ -2585,11 +2590,6 @@ static const struct v4l2_ctrl_ops ov5640_ctrl_ops = {
 	.s_ctrl = ov5640_s_ctrl,
 };
 
-static const char * const test_pattern_menu[] = {
-	"Disabled",
-	"Color bars",
-};
-
 static int ov5640_init_controls(struct ov5640_dev *sensor)
 {
 	const struct v4l2_ctrl_ops *ops = &ov5640_ctrl_ops;
Signature · 1 line
2.20.1
#2 lore raw

PATCH 2/6 media: ov5640: Add register definition for test pattern register

In reply to Chen-Yu Tsai

The OV5640 can generate many types of test patterns, some with additional modifiers, such as a rolling bar, or gamma gradients.

Add the bit definitions for all bits in the test pattern register, and use them to compose the values to be written to the register.

---
 drivers/media/i2c/ov5640.c | 24 ++++++++++++++++++++++--
 1 file changed, 22 insertions(+), 2 deletions(-)
drivers/media/i2c/ov5640.c +22 -2
index 8e4e8fa3685f..22d07b3cc8a2 100644
@@ -2446,10 +2446,30 @@ static const char * const test_pattern_menu[] = {
 	"Color bars",
 };
 
+#define OV5640_TEST_ENABLE		BIT(7)
+#define OV5640_TEST_ROLLING		BIT(6)	/* rolling horizontal bar */
+#define OV5640_TEST_TRANSPARENT		BIT(5)
+#define OV5640_TEST_SQUARE_BW		BIT(4)	/* black & white squares */
+#define OV5640_TEST_BAR_STANDARD	(0 << 2)
+#define OV5640_TEST_BAR_VERT_CHANGE_1	(1 << 2)
+#define OV5640_TEST_BAR_HOR_CHANGE	(2 << 2)
+#define OV5640_TEST_BAR_VERT_CHANGE_2	(3 << 2)
+#define OV5640_TEST_BAR			(0 << 0)
+#define OV5640_TEST_RANDOM		(1 << 0)
+#define OV5640_TEST_SQUARE		(2 << 0)
+#define OV5640_TEST_BLACK		(3 << 0)
+
+static const u8 test_pattern_val[] = {
+	0,
+	OV5640_TEST_ENABLE | OV5640_TEST_TRANSPARENT |
+		OV5640_TEST_BAR_VERT_CHANGE_1 |
+		OV5640_TEST_BAR,
+};
+
 static int ov5640_set_ctrl_test_pattern(struct ov5640_dev *sensor, int value)
 {
-	return ov5640_mod_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
-			      0xa4, value ? 0xa4 : 0);
+	return ov5640_write_reg(sensor, OV5640_REG_PRE_ISP_TEST_SET1,
+				test_pattern_val[value]);
 }
 
 static int ov5640_set_ctrl_light_freq(struct ov5640_dev *sensor, int value)
Signature · 1 line
2.20.1
#3 lore raw

PATCH 3/6 media: ov5640: Disable transparent feature for test pattern

In reply to Chen-Yu Tsai

The transparent feature for test patterns blends the test pattern with an actual captured image. This makes the result non-static, subject to changes in the sensor's field of view.

Test patterns should be predictable and deterministic, even if they are dynamic patterns. Disable the transparent feature of the test pattern.

---
 drivers/media/i2c/ov5640.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/media/i2c/ov5640.c +1 -2
index 22d07b3cc8a2..a1fd69a21df1 100644
@@ -2461,8 +2461,7 @@ static const char * const test_pattern_menu[] = {
 
 static const u8 test_pattern_val[] = {
 	0,
-	OV5640_TEST_ENABLE | OV5640_TEST_TRANSPARENT |
-		OV5640_TEST_BAR_VERT_CHANGE_1 |
+	OV5640_TEST_ENABLE | OV5640_TEST_BAR_VERT_CHANGE_1 |
 		OV5640_TEST_BAR,
 };
 
Signature · 1 line
2.20.1
#4 lore raw

PATCH 4/6 media: ov5640: Add three more test patterns

In reply to Chen-Yu Tsai

The OV5640 driver currently supports a static color bar pattern with a small vertical gamma gradient. The hardware also supports a color square pattern, as well as having a rolling bar for dynamic sequences.

Add three more test patterns:

- color bars with a rolling bar (but without the gamma gradient)
- static color squares
- color squares with a rolling bar

---
 drivers/media/i2c/ov5640.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/media/i2c/ov5640.c +7 -0
index a1fd69a21df1..13311483792c 100644
@@ -2444,6 +2444,9 @@ static int ov5640_set_ctrl_gain(struct ov5640_dev *sensor, bool auto_gain)
 static const char * const test_pattern_menu[] = {
 	"Disabled",
 	"Color bars",
+	"Color bars w/ rolling bar",
+	"Color squares",
+	"Color squares w/ rolling bar",
 };
 
 #define OV5640_TEST_ENABLE		BIT(7)
@@ -2463,6 +2466,10 @@ static const u8 test_pattern_val[] = {
 	0,
 	OV5640_TEST_ENABLE | OV5640_TEST_BAR_VERT_CHANGE_1 |
 		OV5640_TEST_BAR,
+	OV5640_TEST_ENABLE | OV5640_TEST_ROLLING |
+		OV5640_TEST_BAR_VERT_CHANGE_1 | OV5640_TEST_BAR,
+	OV5640_TEST_ENABLE | OV5640_TEST_SQUARE,
+	OV5640_TEST_ENABLE | OV5640_TEST_ROLLING | OV5640_TEST_SQUARE,
 };
 
 static int ov5640_set_ctrl_test_pattern(struct ov5640_dev *sensor, int value)
Signature · 1 line
2.20.1
#5 lore raw

PATCH 5/6 media: ov5640: Set JPEG output timings when outputting JPEG data

In reply to Chen-Yu Tsai

When compression is turned on, the on-bus data is framed according to the compression mode, and the height and width set in VFIFO_VSIZE and VFIFO_HSIZE. If these are not updated correctly, the sensor will send data framed in a manner unexpected by the capture interface, such as having more bytes per line than expected, and having the extra data dropped. This ultimately results in corrupted data.

Set the two values when the media bus is configured for JPEG data, meaning the sensor would be in JPEG mode.

---
 drivers/media/i2c/ov5640.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
drivers/media/i2c/ov5640.c +21 -0
index 13311483792c..1c1dc401c678 100644
@@ -83,6 +83,8 @@
 #define OV5640_REG_SIGMADELTA_CTRL0C	0x3c0c
 #define OV5640_REG_FRAME_CTRL01		0x4202
 #define OV5640_REG_FORMAT_CONTROL00	0x4300
+#define OV5640_REG_VFIFO_HSIZE		0x4602
+#define OV5640_REG_VFIFO_VSIZE		0x4604
 #define OV5640_REG_POLARITY_CTRL00	0x4740
 #define OV5640_REG_MIPI_CTRL00		0x4800
 #define OV5640_REG_DEBUG_MODE		0x4814
@@ -1043,12 +1045,31 @@ static int ov5640_set_dvp_pclk(struct ov5640_dev *sensor, unsigned long rate)
 			      (ilog2(pclk_div) << 4));
 }
 
+/* set JPEG framing sizes */
+static int ov5640_set_jpeg_timings(struct ov5640_dev *sensor,
+				   const struct ov5640_mode_info *mode)
+{
+	int ret;
+
+	ret = ov5640_write_reg16(sensor, OV5640_REG_VFIFO_HSIZE, mode->hact);
+	if (ret < 0)
+		return ret;
+
+	return ov5640_write_reg16(sensor, OV5640_REG_VFIFO_VSIZE, mode->vact);
+}
+
 /* download ov5640 settings to sensor through i2c */
 static int ov5640_set_timings(struct ov5640_dev *sensor,
 			      const struct ov5640_mode_info *mode)
 {
 	int ret;
 
+	if (sensor->fmt.code == MEDIA_BUS_FMT_JPEG_1X8) {
+		ret = ov5640_set_jpeg_timings(sensor, mode);
+		if (ret < 0)
+			return ret;
+	}
+
 	ret = ov5640_write_reg16(sensor, OV5640_REG_TIMING_DVPHO, mode->hact);
 	if (ret < 0)
 		return ret;
Signature · 1 line
2.20.1
#6 lore raw

PATCH 6/6 media: ov5640: Consolidate JPEG compression mode setting

In reply to Chen-Yu Tsai

The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3.

The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data.

As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK.

---
 drivers/media/i2c/ov5640.c | 34 +++++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 11 deletions(-)
drivers/media/i2c/ov5640.c +23 -11
index 1c1dc401c678..3d2c5de73283 100644
@@ -85,6 +85,7 @@
 #define OV5640_REG_FORMAT_CONTROL00	0x4300
 #define OV5640_REG_VFIFO_HSIZE		0x4602
 #define OV5640_REG_VFIFO_VSIZE		0x4604
+#define OV5640_REG_JPG_MODE_SELECT	0x4713
 #define OV5640_REG_POLARITY_CTRL00	0x4740
 #define OV5640_REG_MIPI_CTRL00		0x4800
 #define OV5640_REG_DEBUG_MODE		0x4814
@@ -303,7 +304,7 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
 	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
 	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
 	{0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
-	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x501f, 0x00, 0, 0}, {0x4407, 0x04, 0, 0},
 	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
 	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
@@ -372,7 +373,7 @@ static const struct reg_value ov5640_setting_VGA_640_480[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -391,7 +392,7 @@ static const struct reg_value ov5640_setting_XGA_1024_768[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -410,7 +411,7 @@ static const struct reg_value ov5640_setting_QVGA_320_240[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -429,7 +430,7 @@ static const struct reg_value ov5640_setting_QCIF_176_144[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -448,7 +449,7 @@ static const struct reg_value ov5640_setting_NTSC_720_480[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -467,7 +468,7 @@ static const struct reg_value ov5640_setting_PAL_720_576[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -486,7 +487,7 @@ static const struct reg_value ov5640_setting_720P_1280_720[] = {
 	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
 	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
 	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
 	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
 };
@@ -506,7 +507,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0},
 	{0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
@@ -518,7 +519,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
 	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
 	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
 	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
-	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4407, 0x04, 0, 0},
 	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
 	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
 };
@@ -537,7 +538,7 @@ static const struct reg_value ov5640_setting_QSXGA_2592_1944[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
 };
@@ -1051,6 +1052,17 @@ static int ov5640_set_jpeg_timings(struct ov5640_dev *sensor,
 {
 	int ret;
 
+	/*
+	 * compression mode 3 timing
+	 *
+	 * Data is transmitted with programmable width (VFIFO_HSIZE).
+	 * No padding done. Last line may have less data. Varying
+	 * number of lines per frame, depending on amount of data.
+	 */
+	ret = ov5640_mod_reg(sensor, OV5640_REG_JPEG_MODE_SELECT, 0x7, 0x3);
+	if (ret < 0)
+		return ret;
+
 	ret = ov5640_write_reg16(sensor, OV5640_REG_VFIFO_HSIZE, mode->hact);
 	if (ret < 0)
 		return ret;
Signature · 1 line
2.20.1
maintainer
#7 lore raw

Re: [PATCH 6/6] media: ov5640: Consolidate JPEG compression mode setting

Hi Chen-Yu,

Quoted 22 lines · Chen-Yu Tsai

The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3.

The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data.

As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK.

---
 drivers/media/i2c/ov5640.c | 34 +++++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 11 deletions(-)
drivers/media/i2c/ov5640.c +0 -0
index 1c1dc401c678..3d2c5de73283 100644

drivers/media/i2c/ov5640.c line 88

Quoted 4 lines
drivers/media/i2c/ov5640.c +1 -0
@@ -85,6 +85,7 @@
 #define OV5640_REG_FORMAT_CONTROL00	0x4300
 #define OV5640_REG_VFIFO_HSIZE		0x4602
 #define OV5640_REG_VFIFO_VSIZE		0x4604
+#define OV5640_REG_JPG_MODE_SELECT	0x4713

How has this been tested?

The register is referred to as "OV5640_REG_JPEG_MODE_SELECT" below. I can fix it if it's just a typo, but please confirm.

Thanks.

Quoted 120 lines
drivers/media/i2c/ov5640.c +22 -11
 #define OV5640_REG_POLARITY_CTRL00	0x4740
 #define OV5640_REG_MIPI_CTRL00		0x4800
 #define OV5640_REG_DEBUG_MODE		0x4814
@@ -303,7 +304,7 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
 	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
 	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
 	{0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
-	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x501f, 0x00, 0, 0}, {0x4407, 0x04, 0, 0},
 	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
 	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
@@ -372,7 +373,7 @@ static const struct reg_value ov5640_setting_VGA_640_480[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -391,7 +392,7 @@ static const struct reg_value ov5640_setting_XGA_1024_768[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -410,7 +411,7 @@ static const struct reg_value ov5640_setting_QVGA_320_240[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -429,7 +430,7 @@ static const struct reg_value ov5640_setting_QCIF_176_144[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -448,7 +449,7 @@ static const struct reg_value ov5640_setting_NTSC_720_480[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -467,7 +468,7 @@ static const struct reg_value ov5640_setting_PAL_720_576[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -486,7 +487,7 @@ static const struct reg_value ov5640_setting_720P_1280_720[] = {
 	{0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
 	{0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
 	{0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
 	{0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
 };
@@ -506,7 +507,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0},
 	{0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
@@ -518,7 +519,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
 	{0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
 	{0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
 	{0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
-	{0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+	{0x3a15, 0x60, 0, 0}, {0x4407, 0x04, 0, 0},
 	{0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
 	{0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
 };
@@ -537,7 +538,7 @@ static const struct reg_value ov5640_setting_QSXGA_2592_1944[] = {
 	{0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
 	{0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+	{0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
 	{0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
 	{0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
 };
@@ -1051,6 +1052,17 @@ static int ov5640_set_jpeg_timings(struct ov5640_dev *sensor,
 {
 	int ret;
 
+	/*
+	 * compression mode 3 timing
+	 *
+	 * Data is transmitted with programmable width (VFIFO_HSIZE).
+	 * No padding done. Last line may have less data. Varying
+	 * number of lines per frame, depending on amount of data.
+	 */
+	ret = ov5640_mod_reg(sensor, OV5640_REG_JPEG_MODE_SELECT, 0x7, 0x3);
+	if (ret < 0)
+		return ret;
+
 	ret = ov5640_write_reg16(sensor, OV5640_REG_VFIFO_HSIZE, mode->hact);
 	if (ret < 0)
 		return ret;
Signature · 4 lines
Regards,

Sakari Ailus
[email protected]
#8 lore raw

Re: [PATCH 6/6] media: ov5640: Consolidate JPEG compression mode setting

Quoted 33 lines · Sakari Ailus

Hi Chen-Yu,

Quoted 22 lines · Chen-Yu Tsai

The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3.

The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data.

As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK.

---
 drivers/media/i2c/ov5640.c | 34 +++++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 11 deletions(-)
drivers/media/i2c/ov5640.c +0 -0
index 1c1dc401c678..3d2c5de73283 100644

drivers/media/i2c/ov5640.c line 88

Quoted 4 lines
drivers/media/i2c/ov5640.c +1 -0
@@ -85,6 +85,7 @@
 #define OV5640_REG_FORMAT_CONTROL00  0x4300
 #define OV5640_REG_VFIFO_HSIZE               0x4602
 #define OV5640_REG_VFIFO_VSIZE               0x4604
+#define OV5640_REG_JPG_MODE_SELECT   0x4713

How has this been tested?

Quoted 2 lines

The register is referred to as "OV5640_REG_JPEG_MODE_SELECT" below. I can fix it if it's just a typo, but please confirm.

It's a typo. The datasheet uses the abbreviated form, JPG_MODE_SELECT, but all the bitfield names are the full JPEG form. I believe I missed the other occurrence while fixing up the names to match the datasheet. I appologize for not doing a final compile test.

Thanks
ChenYu

Quoted 128 lines

Thanks.

Quoted 110 lines
drivers/media/i2c/ov5640.c +15 -11
 #define OV5640_REG_POLARITY_CTRL00   0x4740
 #define OV5640_REG_MIPI_CTRL00               0x4800
 #define OV5640_REG_DEBUG_MODE                0x4814
@@ -303,7 +304,7 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
      {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
      {0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
      {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
-     {0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
+     {0x501f, 0x00, 0, 0}, {0x4407, 0x04, 0, 0},
      {0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
      {0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
@@ -372,7 +373,7 @@ static const struct reg_value ov5640_setting_VGA_640_480[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -391,7 +392,7 @@ static const struct reg_value ov5640_setting_XGA_1024_768[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -410,7 +411,7 @@ static const struct reg_value ov5640_setting_QVGA_320_240[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -429,7 +430,7 @@ static const struct reg_value ov5640_setting_QCIF_176_144[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -448,7 +449,7 @@ static const struct reg_value ov5640_setting_NTSC_720_480[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -467,7 +468,7 @@ static const struct reg_value ov5640_setting_PAL_720_576[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0xa3, 0, 0},
 };
@@ -486,7 +487,7 @@ static const struct reg_value ov5640_setting_720P_1280_720[] = {
      {0x3a03, 0xe4, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0xbc, 0, 0},
      {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x72, 0, 0}, {0x3a0e, 0x01, 0, 0},
      {0x3a0d, 0x02, 0, 0}, {0x3a14, 0x02, 0, 0}, {0x3a15, 0xe4, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0},
      {0x3824, 0x04, 0, 0}, {0x5001, 0x83, 0, 0},
 };
@@ -506,7 +507,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 0},
      {0x3c07, 0x07, 0, 0}, {0x3c08, 0x00, 0, 0},
@@ -518,7 +519,7 @@ static const struct reg_value ov5640_setting_1080P_1920_1080[] = {
      {0x3a02, 0x04, 0, 0}, {0x3a03, 0x60, 0, 0}, {0x3a08, 0x01, 0, 0},
      {0x3a09, 0x50, 0, 0}, {0x3a0a, 0x01, 0, 0}, {0x3a0b, 0x18, 0, 0},
      {0x3a0e, 0x03, 0, 0}, {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x04, 0, 0},
-     {0x3a15, 0x60, 0, 0}, {0x4713, 0x02, 0, 0}, {0x4407, 0x04, 0, 0},
+     {0x3a15, 0x60, 0, 0}, {0x4407, 0x04, 0, 0},
      {0x460b, 0x37, 0, 0}, {0x460c, 0x20, 0, 0}, {0x3824, 0x04, 0, 0},
      {0x4005, 0x1a, 0, 0}, {0x3008, 0x02, 0, 0},
 };
@@ -537,7 +538,7 @@ static const struct reg_value ov5640_setting_QSXGA_2592_1944[] = {
      {0x3a03, 0xd8, 0, 0}, {0x3a08, 0x01, 0, 0}, {0x3a09, 0x27, 0, 0},
      {0x3a0a, 0x00, 0, 0}, {0x3a0b, 0xf6, 0, 0}, {0x3a0e, 0x03, 0, 0},
      {0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
-     {0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0}, {0x4713, 0x03, 0, 0},
+     {0x4001, 0x02, 0, 0}, {0x4004, 0x06, 0, 0},
      {0x4407, 0x04, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
      {0x3824, 0x02, 0, 0}, {0x5001, 0x83, 0, 70},
 };
@@ -1051,6 +1052,17 @@ static int ov5640_set_jpeg_timings(struct ov5640_dev *sensor,
 {
      int ret;
 
+     /*
+      * compression mode 3 timing
+      *
+      * Data is transmitted with programmable width (VFIFO_HSIZE).

drivers/media/i2c/ov5640.c static int ov5640_set_jpeg_timings(struct ov5640_dev *sensor, · line 1068

Quoted 10 lines
drivers/media/i2c/ov5640.c +7 -0
+      * No padding done. Last line may have less data. Varying
+      * number of lines per frame, depending on amount of data.
+      */
+     ret = ov5640_mod_reg(sensor, OV5640_REG_JPEG_MODE_SELECT, 0x7, 0x3);
+     if (ret < 0)
+             return ret;
+
      ret = ov5640_write_reg16(sensor, OV5640_REG_VFIFO_HSIZE, mode->hact);
      if (ret < 0)
              return ret;

--
Regards,

Sakari Ailus
[email protected]

maintainer
#9 lore raw

Re: [PATCH 6/6] media: ov5640: Consolidate JPEG compression mode setting

Quoted 35 lines · Chen-Yu Tsai
Quoted 33 lines · Sakari Ailus

Hi Chen-Yu,

Quoted 22 lines · Chen-Yu Tsai

The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3.

The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data.

As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK.

---
 drivers/media/i2c/ov5640.c | 34 +++++++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 11 deletions(-)
drivers/media/i2c/ov5640.c +0 -0
index 1c1dc401c678..3d2c5de73283 100644

drivers/media/i2c/ov5640.c line 88

Quoted 4 lines
drivers/media/i2c/ov5640.c +1 -0
@@ -85,6 +85,7 @@
 #define OV5640_REG_FORMAT_CONTROL00  0x4300
 #define OV5640_REG_VFIFO_HSIZE               0x4602
 #define OV5640_REG_VFIFO_VSIZE               0x4604
+#define OV5640_REG_JPG_MODE_SELECT   0x4713

How has this been tested?

Quoted 7 lines
Quoted 2 lines

The register is referred to as "OV5640_REG_JPEG_MODE_SELECT" below. I can fix it if it's just a typo, but please confirm.

It's a typo. The datasheet uses the abbreviated form, JPG_MODE_SELECT, but all the bitfield names are the full JPEG form. I believe I missed the other occurrence while fixing up the names to match the datasheet. I appologize for not doing a final compile test.

Thanks, and no problem.

Signature · 2 lines
Sakari Ailus
[email protected]