Skip to contentSkip to conversation

mx6sabresd: README: Adjust the binary name after DM conversion

PATCH New Fabio Estevam 2 participants 4 messages Feb 26, 2019

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 mx6sabresd: README: Adjust the binary name after DM conversion

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
 board/freescale/mx6sabresd/README | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
board/freescale/mx6sabresd/README +9 -9
index 4b4df06330..4ea4454b9f 100644
@@ -21,15 +21,15 @@ $ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
 
-- Flash the u-boot.img binary into the SD card:
+- Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
 
 
 2. Booting from eMMC
@@ -39,7 +39,7 @@ $ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Boot first from SD card as shown in the previous section
 
@@ -51,10 +51,10 @@ Mount the eMMC in the host PC:
 
 => ums 0 mmc 2
 
-- Flash SPL and u-boot.img binaries into the eMMC:
+- Flash SPL and u-boot-dtb.img binaries into the eMMC:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
 
 Set SW6 to eMMC 8-bit boot: 11010110
 
@@ -65,15 +65,15 @@ Set SW6 to eMMC 8-bit boot: 11010110
 $ make mx6sabresd_defconfig
 $ make
 
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
 
-- Flash the u-boot.img image into the SD card:
+- Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
 
 Create a partition for root file system and extract it there:
 
Signature · 1 line
2.17.1
#1 lore raw

PATCH 2/2 mx6sabreauto: README: Adjust the binary name after DM conversion

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

---
 board/freescale/mx6sabreauto/README | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
board/freescale/mx6sabreauto/README +6 -6
index e8c589b92a..4c0fda1a2d 100644
@@ -9,15 +9,15 @@ $ make mx6sabreauto_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
 
-- Flash the u-boot.img binary into the SD card:
+- Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
 
 Booting via Falcon mode
 -----------------------
@@ -32,15 +32,15 @@ $ make mx6sabreauto_defconfig
 
 $ make
 
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 && sync
 
-- Flash the u-boot.img image into the SD card:
+- Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdb bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 && sync
 
 Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
 
Signature · 1 line
2.17.1
#3 lore raw

PATCH 1/2 mx6sabresd: README: Adjust the binary name after DM conversion

In reply to Fabio Estevam
Quoted 11 lines

-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: 2019年2月26日 20:36
To: sbabic at denx.de
Cc: dl-uboot-imx <[email protected]>; Peng Fan <[email protected]>; Abel Vesa <[email protected]>; u-boot at lists.denx.de; Fabio Estevam <[email protected]>
Subject: [PATCH 1/2] mx6sabresd: README: Adjust the binary name after DM conversion

Quoted 4 lines

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

Quoted 72 lines
---
 board/freescale/mx6sabresd/README | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
board/freescale/mx6sabresd/README +5 -5
index 4b4df06330..4ea4454b9f 100644
@@ -21,15 +21,15 @@ $ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
 
-- Flash the u-boot.img binary into the SD card:
+- Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
 
 
 2. Booting from eMMC
@@ -39,7 +39,7 @@ $ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Boot first from SD card as shown in the previous section
 
@@ -51,10 +51,10 @@ Mount the eMMC in the host PC:
 
 => ums 0 mmc 2
 
-- Flash SPL and u-boot.img binaries into the eMMC:
+- Flash SPL and u-boot-dtb.img binaries into the eMMC:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync -$ sudo dd

if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync

Set SW6 to eMMC 8-bit boot: 11010110

board/freescale/mx6sabresd/README +0 -0
@@ -65,15 +65,15 @@ Set SW6 to eMMC 8-bit boot: 11010110  $ make

mx6sabresd_defconfig $ make

board/freescale/mx6sabresd/README +2 -3
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
 
-- Flash the u-boot.img image into the SD card:
+- Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none

&& sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync +status=none && sync

Create a partition for root file system and extract it there:

--
2.17.1

#2 lore raw

PATCH 2/2 mx6sabreauto: README: Adjust the binary name after DM conversion

In reply to Fabio Estevam
Quoted 12 lines

-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: 2019年2月26日 20:36
To: sbabic at denx.de
Cc: dl-uboot-imx <[email protected]>; Peng Fan <[email protected]>; Abel Vesa <[email protected]>; u-boot at lists.denx.de; Fabio Estevam <[email protected]>
Subject: [PATCH 2/2] mx6sabreauto: README: Adjust the binary name after DM conversion

Quoted 4 lines

After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly.

Quoted 50 lines
---
 board/freescale/mx6sabreauto/README | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
board/freescale/mx6sabreauto/README +6 -6
index e8c589b92a..4c0fda1a2d 100644
@@ -9,15 +9,15 @@ $ make mx6sabreauto_defconfig
 
 $ make
 
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
 
-- Flash the u-boot.img binary into the SD card:
+- Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
 
 Booting via Falcon mode
 -----------------------
@@ -32,15 +32,15 @@ $ make mx6sabreauto_defconfig
 
 $ make
 
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
 $ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 && sync
 
-- Flash the u-boot.img image into the SD card:
+- Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdb bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 && sync
 
 Create a FAT16 boot partition to store uImage and the dtb file, then copy the

files there:

--
2.17.1