Add MPEG-2 decoding to Rockchip VPU
Subsystems (3)
v2 cover Add MPEG-2 decoding to Rockchip VPU
This series introduces the decoding infrastructure that will be used to add support for other codecs such as VP8, VP9 and H.264.
As explained in the cover letter for the v1 patchset, the driver is now exposing two video device nodes. The VPU encoder is exposed on /dev/video0, and the VPU decoder is exposed on /dev/video1. Both devices are tied to the same memory-to-memory queue, and same media device /dev/media0.
Therefore there are two media graphs:
┌────────────────────────────────┐ │ rockchip,rk3399-vpu-enc-source │ │ /dev/video0 │ └────────────────────────────────┘ ┃ ┃ ▼ ┌────────────────────────────────┐ │ rockchip,rk3399-vpu-enc-proc │ └────────────────────────────────┘ ┃ ┃ ▼ ┌────────────────────────────────┐ │ rockchip,rk3399-vpu-enc-sink │ │ /dev/video0 │ └────────────────────────────────┘
┌────────────────────────────────┐ │ rockchip,rk3399-vpu-dec-source │ │ /dev/video1 │ └────────────────────────────────┘ ┃ ┃ ▼ ┌────────────────────────────────┐ │ rockchip,rk3399-vpu-dec-proc │ └────────────────────────────────┘ ┃ ┃ ▼ ┌────────────────────────────────┐ │ rockchip,rk3399-vpu-dec-sink │ │ /dev/video1 │ └────────────────────────────────┘
Of course, this work has been possible thanks to Jonas Karlman, who did the initial MPEG-2 decoding work and also got mpv+ffmpeg working using the Request API.
This driver can be tested using mpv+ffmpeg for the video decoding side, and the Panfrost mesa driver for rendering.
I should be posting instructions to set all of this up, and also will be submitting the support for H264, VP8 and VP9, hopefully very soon.
v2:
* Fixed some minor issues brought up by v4l2-compliance.
* Fixed bytesused wrongly assigned 0 on the MPEG-2 decoder.
* Addressed comments from Hans and Tomasz on the pixel format helpers.
Ezequiel Garcia (10):
rockchip/vpu: Rename pixel format helpers
media: Introduce helpers to fill pixel format structs rockchip/vpu: Use pixel format helpers rockchip/vpu: Use v4l2_m2m_buf_copy_metadata rockchip/vpu: Cleanup macroblock alignment rockchip/vpu: Cleanup JPEG bounce buffer management rockchip/vpu: Open-code media controller register rockchip/vpu: Support the Request API rockchip/vpu: Add decoder boilerplate rockchip/vpu: Add support for non-standard controls
Jonas Karlman (1):
rockchip/vpu: Add support for MPEG-2 decoding
drivers/media/v4l2-core/v4l2-common.c | 186 ++++++ drivers/staging/media/rockchip/vpu/Makefile | 5 +- .../media/rockchip/vpu/rk3288_vpu_hw.c | 4 +- .../rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c | 4 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 61 +- .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 10 +- .../rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c | 263 +++++++++ .../staging/media/rockchip/vpu/rockchip_vpu.h | 115 +++- .../media/rockchip/vpu/rockchip_vpu_common.h | 10 + .../media/rockchip/vpu/rockchip_vpu_dec.c | 558 ++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 440 ++++++++++++-- .../media/rockchip/vpu/rockchip_vpu_enc.c | 152 ++--- .../media/rockchip/vpu/rockchip_vpu_hw.h | 42 ++ .../media/rockchip/vpu/rockchip_vpu_jpeg.c | 25 + .../media/rockchip/vpu/rockchip_vpu_mpeg2.c | 61 ++ include/media/v4l2-common.h | 32 + 16 files changed, 1795 insertions(+), 173 deletions(-) create mode 100644 drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c create mode 100644 drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c create mode 100644 drivers/staging/media/rockchip/vpu/rockchip_vpu_mpeg2.c
Signature · 7 lines
2.20.1 _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
PATCH v2 1/11 rockchip/vpu: Rename pixel format helpers
The rockchip VPU driver uses generic names for its pixel format helpers. We want to use the same names for generic versions of these helpers, so rename the rockchip ones.
The driver will be switched to the generic helpers later.
--- .../staging/media/rockchip/vpu/rockchip_vpu_enc.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +6 -6
@@ -41,7 +41,7 @@* @is_compressed: Is it a compressed format? * @multiplanar: Is it a multiplanar variant format? (e.g. NV12M) */ -struct v4l2_format_info { +struct rockchip_vpu_v4l2_format_info {u32 format;u32 header_size;u8 num_planes;
@@ -52,10 +52,10 @@ struct v4l2_format_info {u8 multiplanar; }; -static const struct v4l2_format_info * -v4l2_format_info (u32 format) +static const struct rockchip_vpu_v4l2_format_info * +rockchip_vpu_v4l2_format_info (u32 format) { -static const struct v4l2_format_info formats[] = { +static const struct rockchip_vpu_v4l2_format_info formats[] = { { .format =V4L2_PIX_FMT_YUV420M , .num_planes =3 , .cpp = {1 ,1 ,1 }, .hsub =2 , .vsub =2 , .multiplanar =1 }, { .format =V4L2_PIX_FMT_NV12M , .num_planes =2 , .cpp = {1 ,2 ,0 }, .hsub =2 , .vsub =2 , .multiplanar =1 }, { .format =V4L2_PIX_FMT_YUYV , .num_planes =1 , .cpp = {2 ,0 ,0 }, .hsub =2 , .vsub =1 },
@@ -76,11 +76,11 @@ static void fill_pixfmt_mp(struct v4l2_pix_format_mplane *pixfmt, int pixelformat, int width, int height) { - const struct v4l2_format_info *info; + const struct rockchip_vpu_v4l2_format_info *info;struct v4l2_plane_pix_format *plane;int i; - info =v4l2_format_info (pixelformat); + info =rockchip_vpu_v4l2_format_info (pixelformat);if (!info)return ;
Signature · 1 line
2.20.1
PATCH v2 2/11 media: Introduce helpers to fill pixel format structs
In reply to Ezequiel GarciaAdd two new API helpers, v4l2_fill_pixfmt and v4l2_fill_pixfmt_mp, to be used by drivers to calculate plane sizes and bytes per lines.
Note that driver-specific padding and alignment are not taken into account, and must be done by drivers using this API.
--- drivers/media/v4l2-core/v4l2-common.c | 186 ++++++++++++++++++++++++++ include/media/v4l2-common.h | 32 +++++ 2 files changed, 218 insertions(+)
drivers/media/v4l2-core/v4l2-common.c +186 -0
@@ -44,6 +44,7 @@* Added Gerd Knorrs v4l1 enhancements (Justin Schoeman) */ +#include <linux/ctype.h> #include <linux/module.h> #include <linux/types.h> #include <linux/kernel.h>
@@ -445,3 +446,188 @@ int v4l2_s_parm_cap(struct video_device *vdev,return ret; }EXPORT_SYMBOL_GPL (v4l2_s_parm_cap); + +static char printable_char (int c) +{ +return isascii (c) &&isprint (c) ? c :'?' ; +} + +const char *v4l2_get_fourcc_name (uint32_t format) +{ +static char buf[8 ]; + +snprintf (buf,8 , +"%c%c%c%c%s" , +printable_char (format &0xff ), +printable_char ((format >>8 ) &0xff ), +printable_char ((format >>16 ) &0xff ), +printable_char ((format >>24 ) &0x7f ), + (format &BIT (31 )) ?"-BE" :"" ); + +return buf; +} +EXPORT_SYMBOL (v4l2_get_fourcc_name); + +const struct v4l2_format_info *v4l2_format_info (u32 format) +{ +static const struct v4l2_format_info formats[] = { +/* RGB formats */ + { .format =V4L2_PIX_FMT_BGR24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_RGB24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_HSV24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_BGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_XBGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_RGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_XRGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_HSV32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_ARGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_ABGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_GREY , .mem_planes =1 , .comp_planes =1 , .bpp = {1 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + +/* YUV packed formats */ + { .format =V4L2_PIX_FMT_YUYV , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVYU , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_UYVY , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_VYUY , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + +/* YUV planar formats */ + { .format =V4L2_PIX_FMT_NV12 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV21 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV16 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV61 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV24 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV42 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + + { .format =V4L2_PIX_FMT_YUV410 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =4 }, + { .format =V4L2_PIX_FMT_YVU410 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =4 }, + { .format =V4L2_PIX_FMT_YUV411P , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YUV420 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YVU420 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YUV422P , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + +/* YUV planar formats, non contiguous variant */ + { .format =V4L2_PIX_FMT_YUV420M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YVU420M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YUV422M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVU422M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YUV444M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVU444M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =1 , .vdiv =1 }, + + { .format =V4L2_PIX_FMT_NV12M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV21M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV16M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV61M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + }; +unsigned int i; + +for (i =0 ; i <ARRAY_SIZE (formats); ++i) +if (formats[i].format == format) +return &formats[i]; +return NULL ; +} +EXPORT_SYMBOL (v4l2_format_info); + +static inline unsigned int v4l2_format_block_width (const struct v4l2_format_info *info,int plane) +{ +if (!info->block_w[plane]) +return 1 ; +return info->block_w[plane]; +} + +static inline unsigned int v4l2_format_block_height (const struct v4l2_format_info *info,int plane) +{ +if (!info->block_h[plane]) +return 1 ; +return info->block_h[plane]; +} + +int v4l2_fill_pixfmt_mp (struct v4l2_pix_format_mplane *pixfmt, +int pixelformat,int width,int height) +{ +const struct v4l2_format_info *info; +struct v4l2_plane_pix_format *plane; +int i; + + info =v4l2_format_info (pixelformat); +if (!info) +return -EINVAL ; + + pixfmt->width = width; + pixfmt->height = height; + pixfmt->pixelformat = pixelformat; + pixfmt->num_planes = info->mem_planes; + +if (info->mem_planes ==1 ) { + plane = &pixfmt->plane_fmt[0 ]; + plane->bytesperline =ALIGN (width,v4l2_format_block_width (info,0 )) * info->bpp[0 ]; + plane->sizeimage =0 ; + +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + plane->sizeimage += info->bpp[i] * +DIV_ROUND_UP (aligned_width, hdiv) * +DIV_ROUND_UP (aligned_height, vdiv); + } + }else { +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + plane = &pixfmt->plane_fmt[i]; + plane->bytesperline = + info->bpp[i] *DIV_ROUND_UP (aligned_width, hdiv); + plane->sizeimage = + plane->bytesperline *DIV_ROUND_UP (aligned_height, vdiv); + } + } +return 0 ; +} +EXPORT_SYMBOL_GPL (v4l2_fill_pixfmt_mp); + +int v4l2_fill_pixfmt (struct v4l2_pix_format *pixfmt,int pixelformat,int width,int height) +{ +const struct v4l2_format_info *info; +int i; + + info =v4l2_format_info (pixelformat); +if (!info) +return -EINVAL ; + +/* Single planar API cannot be used for multi plane formats. */ +if (info->mem_planes >1 ) +return -EINVAL ; + + pixfmt->width = width; + pixfmt->height = height; + pixfmt->pixelformat = pixelformat; + pixfmt->bytesperline =ALIGN (width,v4l2_format_block_width (info,0 )) * info->bpp[0 ]; + pixfmt->sizeimage =0 ; + +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + pixfmt->sizeimage += info->bpp[i] * +DIV_ROUND_UP (aligned_width, hdiv) * +DIV_ROUND_UP (aligned_height, vdiv); + } +return 0 ; +} +EXPORT_SYMBOL_GPL (v4l2_fill_pixfmt);
include/media/v4l2-common.h +32 -0
@@ -392,4 +392,36 @@ int v4l2_s_parm_cap(struct video_device *vdev, ((u64)(a).numerator * (b).denominator OP \ (u64)(b).numerator * (a).denominator) +/* ------------------------------------------------------------------------- */ + +/* Pixel format and FourCC helpers */ + +/** +* struct v4l2_format_info - information about a V4L2 format +* @format: 4CC format identifier (V4L2_PIX_FMT_*) +* @mem_planes: Number of memory planes, which includes the alpha plane (1 to 4). +* @comp_planes: Number of component planes, which includes the alpha plane (1 to 4). +* @bpp: Array of per-plane bytes per pixel +* @hdiv: Horizontal chroma subsampling factor +* @vdiv: Vertical chroma subsampling factor + */ +struct v4l2_format_info { +u32 format; +u8 mem_planes; +u8 comp_planes; +u8 bpp[4 ]; +u8 hdiv; +u8 vdiv; +u8 block_w[4 ]; +u8 block_h[4 ]; +}; + +const struct v4l2_format_info *v4l2_format_info (u32 format); +const char *v4l2_get_fourcc_name (u32 format); + +int v4l2_fill_pixfmt (struct v4l2_pix_format *pixfmt,int pixelformat, +int width,int height); +int v4l2_fill_pixfmt_mp (struct v4l2_pix_format_mplane *pixfmt,int pixelformat, +int width,int height); +#endif /* V4L2_COMMON_H_ */
Signature · 1 line
2.20.1
Re: [PATCH v2 02/11] media: Introduce helpers to fill pixel format structs
Quoted 39 lines · Ezequiel Garcia
Add two new API helpers,
v4l2_fill_pixfmtandv4l2_fill_pixfmt_mp, to be used by drivers to calculate plane sizes and bytes per lines.Note that driver-specific padding and alignment are not taken into account, and must be done by drivers using this API.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- drivers/media/v4l2-core/v4l2-common.c | 186 ++++++++++++++++++++++++++ include/media/v4l2-common.h | 32 +++++ 2 files changed, 218 insertions(+)drivers/media/v4l2-core/v4l2-common.c +12
-0@@ -44,6 +44,7 @@* Added Gerd Knorrs v4l1 enhancements (Justin Schoeman) */ +#include <linux/ctype.h> #include <linux/module.h> #include <linux/types.h> #include <linux/kernel.h> @@ -445,3 +446,188 @@ int v4l2_s_parm_cap(struct video_device *vdev,return ret; }EXPORT_SYMBOL_GPL (v4l2_s_parm_cap); + +static char printable_char (int c) +{ +return isascii (c) &&isprint (c) ? c :'?' ; +} + +const char *v4l2_get_fourcc_name (uint32_t format) +{ +static char buf[8 ]; + + snprintf(buf, 8,
drivers/media/v4l2-core/v4l2-common.c int v4l2_s_parm_cap(struct video_device *vdev, · line 469
Quoted 10 lines
drivers/media/v4l2-core/v4l2-common.c +10
-0+"%c%c%c%c%s" , +printable_char (format &0xff ), +printable_char ((format >>8 ) &0xff ), +printable_char ((format >>16 ) &0xff ), +printable_char ((format >>24 ) &0x7f ), + (format & BIT(31)) ? "-BE" : ""); + +return buf; +} +EXPORT_SYMBOL (v4l2_get_fourcc_name);
This function isn't re-entrant, but it should be. Multiple threads may be calling it at the same time.
It is probably best to pass the buffer pointer as an argument.
I would also prefer to split this patch into two: the first adding v4l2_format_info, the second adding v4l2_get_fourcc_name. This in case that the v4l2_get_fourcc_name() function needs more work.
Regards,
Hans
Quoted 206 lines
drivers/media/v4l2-core/v4l2-common.c +164
-0+ +const struct v4l2_format_info *v4l2_format_info (u32 format) +{ +static const struct v4l2_format_info formats[] = { +/* RGB formats */ + { .format =V4L2_PIX_FMT_BGR24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_RGB24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_HSV24 , .mem_planes =1 , .comp_planes =1 , .bpp = {3 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_BGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_XBGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_RGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_XRGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_HSV32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_ARGB32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_ABGR32 , .mem_planes =1 , .comp_planes =1 , .bpp = {4 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_GREY , .mem_planes =1 , .comp_planes =1 , .bpp = {1 ,0 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + +/* YUV packed formats */ + { .format =V4L2_PIX_FMT_YUYV , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVYU , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_UYVY , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_VYUY , .mem_planes =1 , .comp_planes =1 , .bpp = {2 ,0 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + +/* YUV planar formats */ + { .format =V4L2_PIX_FMT_NV12 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV21 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV16 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV61 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV24 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV42 , .mem_planes =1 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =1 , .vdiv =1 }, + + { .format =V4L2_PIX_FMT_YUV410 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =4 }, + { .format =V4L2_PIX_FMT_YVU410 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =4 }, + { .format =V4L2_PIX_FMT_YUV411P , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =4 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YUV420 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YVU420 , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YUV422P , .mem_planes =1 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + +/* YUV planar formats, non contiguous variant */ + { .format =V4L2_PIX_FMT_YUV420M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YVU420M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_YUV422M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVU422M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YUV444M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =1 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_YVU444M , .mem_planes =3 , .comp_planes =3 , .bpp = {1 ,1 ,1 ,0 }, .hdiv =1 , .vdiv =1 }, + + { .format =V4L2_PIX_FMT_NV12M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV21M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =2 }, + { .format =V4L2_PIX_FMT_NV16M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + { .format =V4L2_PIX_FMT_NV61M , .mem_planes =2 , .comp_planes =2 , .bpp = {1 ,2 ,0 ,0 }, .hdiv =2 , .vdiv =1 }, + }; +unsigned int i; + +for (i =0 ; i <ARRAY_SIZE (formats); ++i) +if (formats[i].format == format) +return &formats[i]; +return NULL ; +} +EXPORT_SYMBOL (v4l2_format_info); + +static inline unsigned int v4l2_format_block_width (const struct v4l2_format_info *info,int plane) +{ +if (!info->block_w[plane]) +return 1 ; +return info->block_w[plane]; +} + +static inline unsigned int v4l2_format_block_height (const struct v4l2_format_info *info,int plane) +{ +if (!info->block_h[plane]) +return 1 ; +return info->block_h[plane]; +} + +int v4l2_fill_pixfmt_mp (struct v4l2_pix_format_mplane *pixfmt, +int pixelformat,int width,int height) +{ +const struct v4l2_format_info *info; +struct v4l2_plane_pix_format *plane; +int i; + + info =v4l2_format_info (pixelformat); +if (!info) +return -EINVAL ; + + pixfmt->width = width; + pixfmt->height = height; + pixfmt->pixelformat = pixelformat; + pixfmt->num_planes = info->mem_planes; + +if (info->mem_planes ==1 ) { + plane = &pixfmt->plane_fmt[0 ]; + plane->bytesperline =ALIGN (width,v4l2_format_block_width (info,0 )) * info->bpp[0 ]; + plane->sizeimage =0 ; + +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + plane->sizeimage += info->bpp[i] * +DIV_ROUND_UP (aligned_width, hdiv) * +DIV_ROUND_UP (aligned_height, vdiv); + } + }else { +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + plane = &pixfmt->plane_fmt[i]; + plane->bytesperline = + info->bpp[i] *DIV_ROUND_UP (aligned_width, hdiv); + plane->sizeimage = + plane->bytesperline *DIV_ROUND_UP (aligned_height, vdiv); + } + } +return 0 ; +} +EXPORT_SYMBOL_GPL (v4l2_fill_pixfmt_mp); + +int v4l2_fill_pixfmt (struct v4l2_pix_format *pixfmt,int pixelformat,int width,int height) +{ +const struct v4l2_format_info *info; +int i; + + info =v4l2_format_info (pixelformat); +if (!info) +return -EINVAL ; + +/* Single planar API cannot be used for multi plane formats. */ +if (info->mem_planes >1 ) +return -EINVAL ; + + pixfmt->width = width; + pixfmt->height = height; + pixfmt->pixelformat = pixelformat; + pixfmt->bytesperline =ALIGN (width,v4l2_format_block_width (info,0 )) * info->bpp[0 ]; + pixfmt->sizeimage =0 ; + +for (i =0 ; i < info->comp_planes; i++) { +unsigned int hdiv = (i ==0 ) ?1 : info->hdiv; +unsigned int vdiv = (i ==0 ) ?1 : info->vdiv; +unsigned int aligned_width; +unsigned int aligned_height; + + aligned_width =ALIGN (width,v4l2_format_block_width (info, i)); + aligned_height =ALIGN (height,v4l2_format_block_height (info, i)); + + pixfmt->sizeimage += info->bpp[i] * +DIV_ROUND_UP (aligned_width, hdiv) * +DIV_ROUND_UP (aligned_height, vdiv); + } +return 0 ; +} +EXPORT_SYMBOL_GPL (v4l2_fill_pixfmt);include/media/v4l2-common.h +32
-0@@ -392,4 +392,36 @@ int v4l2_s_parm_cap(struct video_device *vdev, ((u64)(a).numerator * (b).denominator OP \ (u64)(b).numerator * (a).denominator) +/* ------------------------------------------------------------------------- */ + +/* Pixel format and FourCC helpers */ + +/** +* struct v4l2_format_info - information about a V4L2 format +* @format: 4CC format identifier (V4L2_PIX_FMT_*) +* @mem_planes: Number of memory planes, which includes the alpha plane (1 to 4). +* @comp_planes: Number of component planes, which includes the alpha plane (1 to 4). +* @bpp: Array of per-plane bytes per pixel +* @hdiv: Horizontal chroma subsampling factor +* @vdiv: Vertical chroma subsampling factor + */ +struct v4l2_format_info { +u32 format; +u8 mem_planes; +u8 comp_planes; +u8 bpp[4 ]; +u8 hdiv; +u8 vdiv; +u8 block_w[4 ]; +u8 block_h[4 ]; +}; + +const struct v4l2_format_info *v4l2_format_info (u32 format); +const char *v4l2_get_fourcc_name (u32 format); + +int v4l2_fill_pixfmt (struct v4l2_pix_format *pixfmt,int pixelformat, +int width,int height); +int v4l2_fill_pixfmt_mp (struct v4l2_pix_format_mplane *pixfmt,int pixelformat, +int width,int height); +#endif /* V4L2_COMMON_H_ */
Re: [PATCH v2 02/11] media: Introduce helpers to fill pixel format structs
Quoted 54 lines · Hans Verkuil
Quoted 39 lines · Ezequiel Garcia
Add two new API helpers,
v4l2_fill_pixfmtandv4l2_fill_pixfmt_mp, to be used by drivers to calculate plane sizes and bytes per lines.Note that driver-specific padding and alignment are not taken into account, and must be done by drivers using this API.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- drivers/media/v4l2-core/v4l2-common.c | 186 ++++++++++++++++++++++++++ include/media/v4l2-common.h | 32 +++++ 2 files changed, 218 insertions(+)drivers/media/v4l2-core/v4l2-common.c +12
-0@@ -44,6 +44,7 @@* Added Gerd Knorrs v4l1 enhancements (Justin Schoeman) */ +#include <linux/ctype.h> #include <linux/module.h> #include <linux/types.h> #include <linux/kernel.h> @@ -445,3 +446,188 @@ int v4l2_s_parm_cap(struct video_device *vdev,return ret; }EXPORT_SYMBOL_GPL (v4l2_s_parm_cap); + +static char printable_char (int c) +{ +return isascii (c) &&isprint (c) ? c :'?' ; +} + +const char *v4l2_get_fourcc_name (uint32_t format) +{ +static char buf[8 ]; + + snprintf(buf, 8,drivers/media/v4l2-core/v4l2-common.c int v4l2_s_parm_cap(struct video_device *vdev, · line 469
Quoted 10 lines
drivers/media/v4l2-core/v4l2-common.c +10
-0+"%c%c%c%c%s" , +printable_char (format &0xff ), +printable_char ((format >>8 ) &0xff ), +printable_char ((format >>16 ) &0xff ), +printable_char ((format >>24 ) &0x7f ), + (format & BIT(31)) ? "-BE" : ""); + +return buf; +} +EXPORT_SYMBOL (v4l2_get_fourcc_name);This function isn't re-entrant, but it should be. Multiple threads may be calling it at the same time.
Quoted 2 lines
It is probably best to pass the buffer pointer as an argument.
Boy, shame on me, really missed this!
Quoted 4 lines
I would also prefer to split this patch into two: the first adding
v4l2_format_info, the second addingv4l2_get_fourcc_name. This in case that thev4l2_get_fourcc_name()function needs more work.
OK.
Thanks a lot for the feedback,
Eze
Re: [PATCH v2 02/11] media: Introduce helpers to fill pixel format structs
In reply to Ezequiel GarciaHi Ezequiel,
Quoted 11 lines · Ezequiel Garcia
include/media/v4l2-common.h +11
-0+ +/* Pixel format and FourCC helpers */ + +/** +* struct v4l2_format_info - information about a V4L2 format +* @format: 4CC format identifier (V4L2_PIX_FMT_*) +* @mem_planes: Number of memory planes, which includes the alpha plane (1 to 4). +* @comp_planes: Number of component planes, which includes the alpha plane (1 to 4). +* @bpp: Array of per-plane bytes per pixel +* @hdiv: Horizontal chroma subsampling factor +* @vdiv: Vertical chroma subsampling factor
include/media/v4l2-common.h int v4l2_s_parm_cap(struct video_device *vdev, · line 416
Quoted 10 lines
include/media/v4l2-common.h +10
-0+*/ +struct v4l2_format_info { +u32 format; +u8 mem_planes; +u8 comp_planes; +u8 bpp[4 ]; +u8 hdiv; +u8 vdiv; +u8 block_w[4 ]; +u8 block_h[4 ];
Please don't forget to document block_[wh]. Plus you can draw some extra inspiration from drm_format_info in include/drm/drm_fourcc.h ;-)
HTH
Emil
PATCH v2 3/11 rockchip/vpu: Use pixel format helpers
In reply to Ezequiel GarciaNow that we've introduced the pixel format helpers, use them in vpu driver, and get rid of the internal helpers.
--- .../media/rockchip/vpu/rockchip_vpu_enc.c | 91 +------------------ 1 file changed, 2 insertions(+), 89 deletions(-)
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +2 -89
@@ -30,93 +30,6 @@#include "rockchip_vpu_hw.h" #include "rockchip_vpu_common.h" -/** -* struct v4l2_format_info - information about a V4L2 format -* @format: 4CC format identifier (V4L2_PIX_FMT_*) -* @header_size: Size of header, optional and used by compressed formats -* @num_planes: Number of planes (1 to 3) -* @cpp: Number of bytes per pixel (per plane) -* @hsub: Horizontal chroma subsampling factor -* @vsub: Vertical chroma subsampling factor -* @is_compressed: Is it a compressed format? -* @multiplanar: Is it a multiplanar variant format? (e.g. NV12M) -*/ -struct rockchip_vpu_v4l2_format_info { -u32 format; -u32 header_size; -u8 num_planes; -u8 cpp[3 ]; -u8 hsub; -u8 vsub; -u8 is_compressed; -u8 multiplanar; -}; - -static const struct rockchip_vpu_v4l2_format_info * -rockchip_vpu_v4l2_format_info (u32 format) -{ -static const struct rockchip_vpu_v4l2_format_info formats[] = { - { .format =V4L2_PIX_FMT_YUV420M , .num_planes =3 , .cpp = {1 ,1 ,1 }, .hsub =2 , .vsub =2 , .multiplanar =1 }, - { .format =V4L2_PIX_FMT_NV12M , .num_planes =2 , .cpp = {1 ,2 ,0 }, .hsub =2 , .vsub =2 , .multiplanar =1 }, - { .format =V4L2_PIX_FMT_YUYV , .num_planes =1 , .cpp = {2 ,0 ,0 }, .hsub =2 , .vsub =1 }, - { .format =V4L2_PIX_FMT_UYVY , .num_planes =1 , .cpp = {2 ,0 ,0 }, .hsub =2 , .vsub =1 }, - }; -unsigned int i; - -for (i =0 ; i <ARRAY_SIZE (formats); ++i) { -if (formats[i].format == format) -return &formats[i]; - } - -vpu_err ("Unsupported V4L 4CC format (%08x)\n" , format); -return NULL ; -} - -static void -fill_pixfmt_mp (struct v4l2_pix_format_mplane *pixfmt, -int pixelformat,int width,int height) -{ -const struct rockchip_vpu_v4l2_format_info *info; -struct v4l2_plane_pix_format *plane; -int i; - - info =rockchip_vpu_v4l2_format_info (pixelformat); -if (!info) -return ; - - pixfmt->width = width; - pixfmt->height = height; - pixfmt->pixelformat = pixelformat; - -if (!info->multiplanar) { - pixfmt->num_planes =1 ; - plane = &pixfmt->plane_fmt[0 ]; - plane->bytesperline = info->is_compressed ? -0 : width * info->cpp[0 ]; - plane->sizeimage = info->header_size; -for (i =0 ; i < info->num_planes; i++) { -unsigned int hsub = (i ==0 ) ?1 : info->hsub; -unsigned int vsub = (i ==0 ) ?1 : info->vsub; - - plane->sizeimage += info->cpp[i] * -DIV_ROUND_UP (width, hsub) * -DIV_ROUND_UP (height, vsub); - } - }else { - pixfmt->num_planes = info->num_planes; -for (i =0 ; i < info->num_planes; i++) { -unsigned int hsub = (i ==0 ) ?1 : info->hsub; -unsigned int vsub = (i ==0 ) ?1 : info->vsub; - - plane = &pixfmt->plane_fmt[i]; - plane->bytesperline = - info->cpp[i] *DIV_ROUND_UP (width, hsub); - plane->sizeimage = - plane->bytesperline *DIV_ROUND_UP (height, vsub); - } - } -} -static const struct rockchip_vpu_fmt *rockchip_vpu_find_format (struct rockchip_vpu_ctx *ctx,u32 fourcc) {
@@ -339,7 +252,7 @@ vidioc_try_fmt_out_mplane(struct file *file, void *priv, struct v4l2_format *f) height =round_up (height,JPEG_MB_DIM );/* Fill remaining fields */ -fill_pixfmt_mp (pix_mp, fmt->fourcc, width, height); +v4l2_fill_pixfmt_mp (pix_mp, fmt->fourcc, width, height);for (i =0 ; i < pix_mp->num_planes; i++) { memset(pix_mp->plane_fmt[i].reserved, 0,
@@ -393,7 +306,7 @@ void rockchip_vpu_enc_reset_src_fmt(struct rockchip_vpu_dev *vpu, fmt->quantization =V4L2_QUANTIZATION_DEFAULT ; fmt->xfer_func =V4L2_XFER_FUNC_DEFAULT ; -fill_pixfmt_mp (fmt, ctx->vpu_src_fmt->fourcc, width, height); +v4l2_fill_pixfmt_mp (fmt, ctx->vpu_src_fmt->fourcc, width, height); } static int
Signature · 1 line
2.20.1
PATCH v2 4/11 rockchip/vpu: Use v4l2_m2m_buf_copy_metadata
In reply to Ezequiel GarciaUse the recently introduced v4l2_m2m_buf_copy_metadata helper and get rid of some code.
--- drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c | 9 +-------- 1 file changed, 1 insertion(+), 8 deletions(-)
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +1 -8
@@ -59,14 +59,7 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, src->sequence = ctx->sequence_out++; dst->sequence = ctx->sequence_cap++; - dst->field = src->field; -if (src->flags &V4L2_BUF_FLAG_TIMECODE ) - dst->timecode = src->timecode; - dst->vb2_buf.timestamp = src->vb2_buf.timestamp; - dst->flags &= ~(V4L2_BUF_FLAG_TSTAMP_SRC_MASK | -V4L2_BUF_FLAG_TIMECODE ); - dst->flags |= src->flags & (V4L2_BUF_FLAG_TSTAMP_SRC_MASK | -V4L2_BUF_FLAG_TIMECODE ); +v4l2_m2m_buf_copy_metadata (src, dst, true); avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size;
Signature · 1 line
2.20.1
PATCH v2 5/11 rockchip/vpu: Cleanup macroblock alignment
In reply to Ezequiel GarciaWe need to make the macrobock alignment generic, in order to support multiple codecs.
--- .../media/rockchip/vpu/rockchip_vpu_enc.c | 20 ++++++++----------- 1 file changed, 8 insertions(+), 12 deletions(-)
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +8 -12
@@ -203,8 +203,8 @@ vidioc_try_fmt_cap_mplane(struct file *file, void *priv, struct v4l2_format *f) fmt->frmsize.min_height, fmt->frmsize.max_height);/* Round up to macroblocks. */ - pix_mp->width =round_up (pix_mp->width,JPEG_MB_DIM ); - pix_mp->height =round_up (pix_mp->height,JPEG_MB_DIM ); + pix_mp->width =round_up (pix_mp->width, fmt->frmsize.step_width); + pix_mp->height =round_up (pix_mp->height, fmt->frmsize.step_height);/* * For compressed formats the application can specify
@@ -248,8 +248,8 @@ vidioc_try_fmt_out_mplane(struct file *file, void *priv, struct v4l2_format *f) ctx->vpu_dst_fmt->frmsize.min_height, ctx->vpu_dst_fmt->frmsize.max_height);/* Round up to macroblocks. */ - width =round_up (width,JPEG_MB_DIM ); - height =round_up (height,JPEG_MB_DIM ); + width =round_up (width, ctx->vpu_dst_fmt->frmsize.step_width); + height =round_up (height, ctx->vpu_dst_fmt->frmsize.step_height);/* Fill remaining fields */ v4l2_fill_pixfmt_mp (pix_mp, fmt->fourcc, width, height);
@@ -338,10 +338,8 @@ vidioc_s_fmt_out_mplane(struct file *file, void *priv, struct v4l2_format *f) ctx->dst_fmt.height = pix_mp->height;vpu_debug (0 ,"OUTPUT codec mode: %d\n" , ctx->vpu_src_fmt->codec_mode); -vpu_debug (0 ,"fmt - w: %d, h: %d, mb - w: %d, h: %d\n" , - pix_mp->width, pix_mp->height, -JPEG_MB_WIDTH (pix_mp->width), -JPEG_MB_HEIGHT (pix_mp->height)); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height);return 0 ; }
@@ -380,10 +378,8 @@ vidioc_s_fmt_cap_mplane(struct file *file, void *priv, struct v4l2_format *f) ctx->dst_fmt = *pix_mp;vpu_debug (0 ,"CAPTURE codec mode: %d\n" , ctx->vpu_dst_fmt->codec_mode); -vpu_debug (0 ,"fmt - w: %d, h: %d, mb - w: %d, h: %d\n" , - pix_mp->width, pix_mp->height, -JPEG_MB_WIDTH (pix_mp->width), -JPEG_MB_HEIGHT (pix_mp->height)); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height);/* * Current raw format might have become invalid with newly
Signature · 1 line
2.20.1
PATCH v2 6/11 rockchip/vpu: Cleanup JPEG bounce buffer management
In reply to Ezequiel GarciaIn order to make the code more generic, introduce a pair of start/stop codec operations, and use them to allocate and release the JPEG bounce buffer.
--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c | 4 +-- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 4 +-- .../staging/media/rockchip/vpu/rockchip_vpu.h | 12 ++++---- .../media/rockchip/vpu/rockchip_vpu_drv.c | 10 +++++-- .../media/rockchip/vpu/rockchip_vpu_enc.c | 23 +++++---------- .../media/rockchip/vpu/rockchip_vpu_hw.h | 28 +++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_jpeg.c | 25 +++++++++++++++++ 9 files changed, 81 insertions(+), 29 deletions(-)
drivers/staging/media/rockchip/vpu/rk3288_vpu_hw.c +2 -0
@@ -98,6 +98,8 @@ static const struct rockchip_vpu_codec_ops rk3288_vpu_codec_ops[] = { [RK_VPU_MODE_JPEG_ENC ] = { .run = rk3288_vpu_jpeg_enc_run, .reset = rk3288_vpu_enc_reset, + .start = rockchip_vpu_jpeg_enc_start, + .stop = rockchip_vpu_jpeg_enc_stop, }, };
drivers/staging/media/rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c +2 -2
@@ -37,9 +37,9 @@ static void rk3288_vpu_jpeg_enc_set_buffers(struct rockchip_vpu_dev *vpu,WARN_ON (pix_fmt->num_planes >3 ); -vepu_write_relaxed (vpu, ctx->bounce_dma_addr, +vepu_write_relaxed (vpu, ctx->jpeg_enc_ctx.bounce_buffer.dma,VEPU_REG_ADDR_OUTPUT_STREAM ); -vepu_write_relaxed (vpu, ctx->bounce_size, +vepu_write_relaxed (vpu, ctx->jpeg_enc_ctx.bounce_buffer.size,VEPU_REG_STR_BUF_LIMIT );if (pix_fmt->num_planes ==1 ) {
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +2 -0
@@ -98,6 +98,8 @@ static const struct rockchip_vpu_codec_ops rk3399_vpu_codec_ops[] = { [RK_VPU_MODE_JPEG_ENC ] = { .run = rk3399_vpu_jpeg_enc_run, .reset = rk3399_vpu_enc_reset, + .start = rockchip_vpu_jpeg_enc_start, + .stop = rockchip_vpu_jpeg_enc_stop, }, };
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c +2 -2
@@ -69,9 +69,9 @@ static void rk3399_vpu_jpeg_enc_set_buffers(struct rockchip_vpu_dev *vpu,WARN_ON (pix_fmt->num_planes >3 ); -vepu_write_relaxed (vpu, ctx->bounce_dma_addr, +vepu_write_relaxed (vpu, ctx->jpeg_enc_ctx.bounce_buffer.dma,VEPU_REG_ADDR_OUTPUT_STREAM ); -vepu_write_relaxed (vpu, ctx->bounce_size, +vepu_write_relaxed (vpu, ctx->jpeg_enc_ctx.bounce_buffer.size,VEPU_REG_STR_BUF_LIMIT );if (pix_fmt->num_planes ==1 ) {
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +5 -7
@@ -124,10 +124,7 @@ struct rockchip_vpu_dev {* @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. -* -* @bounce_dma_addr: Bounce buffer bus address. -* @bounce_buf: Bounce buffer pointer. -* @bounce_size: Bounce buffer size. +* @jpeg_enc_ctx: JPEG-encoding context. */ struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;
@@ -146,9 +143,10 @@ struct rockchip_vpu_ctx {const struct rockchip_vpu_codec_ops *codec_ops; -dma_addr_t bounce_dma_addr; -void *bounce_buf; -size_t bounce_size; +/* Specific for particular codec modes. */ +union { +struct rockchip_vpu_jpeg_enc_hw_ctx jpeg_enc_ctx; + }; };/**
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +8 -2
@@ -64,10 +64,16 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size;if (bytesused <= avail_size) { -if (ctx->bounce_buf) { +/* +* This works while JPEG is the only encoder this driver +* supports. We will have to abstract this step, or get +* rid of the bounce buffer before we can support +* encoding other codecs. +*/ +if (ctx->jpeg_enc_ctx.bounce_buffer.cpu) {memcpy (vb2_plane_vaddr (&dst->vb2_buf,0 ) + ctx->vpu_dst_fmt->header_size, - ctx->bounce_buf, bytesused); + ctx->jpeg_enc_ctx.bounce_buffer.cpu, bytesused); } dst->vb2_buf.planes[0 ].bytesused = ctx->vpu_dst_fmt->header_size + bytesused;
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +7 -16
@@ -514,6 +514,7 @@ static int rockchip_vpu_start_streaming(struct vb2_queue *q, unsigned int count) {struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q);enum rockchip_vpu_codec_mode codec_mode; +int ret =0 ;if (V4L2_TYPE_IS_OUTPUT (q->type)) ctx->sequence_out =0 ;
@@ -526,17 +527,10 @@ static int rockchip_vpu_start_streaming(struct vb2_queue *q, unsigned int count)vpu_debug (4 ,"Codec mode = %d\n" , codec_mode); ctx->codec_ops = &ctx->dev->variant->codec_ops[codec_mode]; -/* A bounce buffer is needed for the JPEG payload */ -if (!V4L2_TYPE_IS_OUTPUT (q->type)) { - ctx->bounce_size = ctx->dst_fmt.plane_fmt[0 ].sizeimage - - ctx->vpu_dst_fmt->header_size; - ctx->bounce_buf =dma_alloc_attrs (ctx->dev->dev, - ctx->bounce_size, - &ctx->bounce_dma_addr, -GFP_KERNEL , -DMA_ATTR_ALLOC_SINGLE_PAGES ); - } -return 0 ; +if (!V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->start) + ret = ctx->codec_ops->start (ctx); +return ret; }static void rockchip_vpu_stop_streaming (struct vb2_queue *q)
@@ -544,11 +538,8 @@ static void rockchip_vpu_stop_streaming(struct vb2_queue *q)struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q);if (!V4L2_TYPE_IS_OUTPUT (q->type)) -dma_free_attrs (ctx->dev->dev, - ctx->bounce_size, - ctx->bounce_buf, - ctx->bounce_dma_addr, -DMA_ATTR_ALLOC_SINGLE_PAGES ); +if (ctx->codec_ops && ctx->codec_ops->stop) + ctx->codec_ops->stop (ctx);/* * The mem2mem framework calls v4l2_m2m_cancel_job before
drivers/staging/media/rockchip/vpu/rockchip_vpu_hw.h +28 -0
@@ -18,9 +18,33 @@ struct rockchip_vpu_ctx;struct rockchip_vpu_buf ;struct rockchip_vpu_variant ; +/** +* struct rockchip_vpu_aux_buf - auxiliary DMA buffer for hardware data +* @cpu: CPU pointer to the buffer. +* @dma: DMA address of the buffer. +* @size: Size of the buffer. +*/ +struct rockchip_vpu_aux_buf { +void *cpu; +dma_addr_t dma; +size_t size; +}; + +/** +* struct rockchip_vpu_jpeg_enc_hw_ctx +* @bounce_buffer: Bounce buffer +*/ +struct rockchip_vpu_jpeg_enc_hw_ctx { +struct rockchip_vpu_aux_buf bounce_buffer; +}; +/** * struct rockchip_vpu_codec_ops - codec mode specific operations * +* @start: If needed, can be used for initialization. +* Optional and called from process context. +* @stop: If needed, can be used to undo the .start phase. +* Optional and called from process context. * @run: Start single {en,de)coding job. Called from atomic context * to indicate that a pair of buffers is ready and the hardware * should be programmed and started.
@@ -28,6 +52,8 @@ struct rockchip_vpu_variant;* @reset: Reset the hardware in case of a timeout. */ struct rockchip_vpu_codec_ops { +int (*start)(struct rockchip_vpu_ctx *ctx); +void (*stop)(struct rockchip_vpu_ctx *ctx);void (*run)(struct rockchip_vpu_ctx *ctx);void (*done)(struct rockchip_vpu_ctx *ctx,enum vb2_buffer_state );void (*reset)(struct rockchip_vpu_ctx *ctx);
@@ -54,5 +80,7 @@ void rockchip_vpu_irq_done(struct rockchip_vpu_dev *vpu,void rk3288_vpu_jpeg_enc_run (struct rockchip_vpu_ctx *ctx);void rk3399_vpu_jpeg_enc_run (struct rockchip_vpu_ctx *ctx); +int rockchip_vpu_jpeg_enc_start (struct rockchip_vpu_ctx *ctx); +void rockchip_vpu_jpeg_enc_stop (struct rockchip_vpu_ctx *ctx);#endif /* ROCKCHIP_VPU_HW_H_ */
drivers/staging/media/rockchip/vpu/rockchip_vpu_jpeg.c +25 -0
@@ -6,9 +6,11 @@* Copyright (C) Jean-Francois Moine (http://moinejf.free.fr) * Copyright (C) 2014 Philipp Zabel, Pengutronix */ +#include <linux/dma-mapping.h> #include <linux/kernel.h> #include <linux/string.h> #include "rockchip_vpu_jpeg.h" +#include "rockchip_vpu.h" #define LUMA_QUANT_OFF 7#define CHROMA_QUANT_OFF 72
@@ -288,3 +290,26 @@ void rockchip_vpu_jpeg_header_assemble(struct rockchip_vpu_jpeg_ctx *ctx)jpeg_set_quality (buf, ctx->quality); } + +int rockchip_vpu_jpeg_enc_start (struct rockchip_vpu_ctx *ctx) +{ + ctx->jpeg_enc_ctx.bounce_buffer.size = ctx->dst_fmt.plane_fmt[0 ].sizeimage - + ctx->vpu_dst_fmt->header_size; + ctx->jpeg_enc_ctx.bounce_buffer.cpu =dma_alloc_attrs (ctx->dev->dev, + ctx->jpeg_enc_ctx.bounce_buffer.size, + &ctx->jpeg_enc_ctx.bounce_buffer.dma, +GFP_KERNEL , +DMA_ATTR_ALLOC_SINGLE_PAGES ); +if (!ctx->jpeg_enc_ctx.bounce_buffer.cpu) +return -ENOMEM ; +return 0 ; +} + +void rockchip_vpu_jpeg_enc_stop (struct rockchip_vpu_ctx *ctx) +{ +dma_free_attrs (ctx->dev->dev, + ctx->jpeg_enc_ctx.bounce_buffer.size, + ctx->jpeg_enc_ctx.bounce_buffer.cpu, + ctx->jpeg_enc_ctx.bounce_buffer.dma, +DMA_ATTR_ALLOC_SINGLE_PAGES ); +}
Signature · 1 line
2.20.1
Re: [PATCH v2 06/11] rockchip/vpu: Cleanup JPEG bounce buffer management
Hi Ezequiel,
Quoted 6 lines · Ezequiel Garcia
In order to make the code more generic, introduce a pair of start/stop codec operations, and use them to allocate and release the JPEG bounce buffer.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>
Quoted 12 lines
--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c | 4 +-- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 4 +-- .../staging/media/rockchip/vpu/rockchip_vpu.h | 12 ++++---- .../media/rockchip/vpu/rockchip_vpu_drv.c | 10 +++++-- .../media/rockchip/vpu/rockchip_vpu_enc.c | 23 +++++---------- .../media/rockchip/vpu/rockchip_vpu_hw.h | 28 +++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_jpeg.c | 25 +++++++++++++++++ 9 files changed, 81 insertions(+), 29 deletions(-)
Thanks for the series! Really sorry for late reply...
[snip]
Quoted 17 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-4@@ -124,10 +124,7 @@ struct rockchip_vpu_dev {* @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. -* -* @bounce_dma_addr: Bounce buffer bus address. -* @bounce_buf: Bounce buffer pointer. -* @bounce_size: Bounce buffer size. +* @jpeg_enc_ctx: JPEG-encoding context. */ struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;
drivers/staging/media/rockchip/vpu/rockchip_vpu.h struct rockchip_vpu_ctx { · line 149
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +4
-3@@ -146,9 +143,10 @@ struct rockchip_vpu_ctx {const struct rockchip_vpu_codec_ops *codec_ops; -dma_addr_t bounce_dma_addr; -void *bounce_buf; -size_t bounce_size; +/* Specific for particular codec modes. */ +union { +struct rockchip_vpu_jpeg_enc_hw_ctx jpeg_enc_ctx; + };
nit: Would it perhaps make it a bit cleaner to call the union "ctx"? Then we wouldn't need to repeat "_ctx" in every field.
Quoted 8 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +0
-0};/** drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, · line 71
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-1@@ -64,10 +64,16 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size;if (bytesused <= avail_size) { -if (ctx->bounce_buf) { +/* +* This works while JPEG is the only encoder this driver +* supports. We will have to abstract this step, or get +* rid of the bounce buffer before we can support +* encoding other codecs.
Hmm, why wouldn't it work for other encoders, which shouldn't require a bounce buffer?
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +3
-1+*/ +if (ctx->jpeg_enc_ctx.bounce_buffer.cpu) {memcpy (vb2_plane_vaddr (&dst->vb2_buf,0 ) + ctx->vpu_dst_fmt->header_size, - ctx->bounce_buf, bytesused); + ctx->jpeg_enc_ctx.bounce_buffer.cpu, bytesused); } dst->vb2_buf.planes[0 ].bytesused = ctx->vpu_dst_fmt->header_size + bytesused;
[snip]
Quoted 7 lines
/**
* structrockchip_vpu_codec_ops- codec mode specific operations *+ * @start: If needed, can be used for initialization. + * Optional and called from process context. + * @stop: If needed, can be used to undo the .start phase. + * Optional and called from process context.
nit: Perhaps .init and .exit could reflect better what these ops do?
Best regards,
Tomasz
Re: [PATCH v2 06/11] rockchip/vpu: Cleanup JPEG bounce buffer management
Quoted 45 lines · Tomasz Figa
Hi Ezequiel,
Quoted 5 lines · Ezequiel Garcia
In order to make the code more generic, introduce a pair of start/stop codec operations, and use them to allocate and release the JPEG bounce buffer.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>Quoted 12 lines
--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c | 4 +-- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 4 +-- .../staging/media/rockchip/vpu/rockchip_vpu.h | 12 ++++---- .../media/rockchip/vpu/rockchip_vpu_drv.c | 10 +++++-- .../media/rockchip/vpu/rockchip_vpu_enc.c | 23 +++++---------- .../media/rockchip/vpu/rockchip_vpu_hw.h | 28 +++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_jpeg.c | 25 +++++++++++++++++ 9 files changed, 81 insertions(+), 29 deletions(-)Thanks for the series! Really sorry for late reply...
[snip]
Quoted 20 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-4@@ -124,10 +124,7 @@ struct rockchip_vpu_dev {* @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. -* -* @bounce_dma_addr: Bounce buffer bus address. -* @bounce_buf: Bounce buffer pointer. -* @bounce_size: Bounce buffer size. +* @jpeg_enc_ctx: JPEG-encoding context. */ struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;@@ -146,9 +143,10 @@ struct rockchip_vpu_ctx {const struct rockchip_vpu_codec_ops *codec_ops;
Quoted 11 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h struct rockchip_vpu_ctx { · line 149
Quoted 7 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +4
-3-dma_addr_t bounce_dma_addr; -void *bounce_buf; -size_t bounce_size; +/* Specific for particular codec modes. */ +union { +struct rockchip_vpu_jpeg_enc_hw_ctx jpeg_enc_ctx; + };nit: Would it perhaps make it a bit cleaner to call the union "ctx"? Then we wouldn't need to repeat "
_ctx" in every field.
Well, the struct is already rockchip_vpu_ctx, so access would look like:
ctx->ctx.jpeg_enc, ctx->ctx.mpeg2_dec
Perhaps we can just drop the _ctx, and so:
ctx->jpeg_enc, ctx->mpeg2_dec
Quoted 12 lines
Quoted 12 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +0
-0};/** drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-1@@ -64,10 +64,16 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size;if (bytesused <= avail_size) { -if (ctx->bounce_buf) {
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, · line 71
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-0+/* +* This works while JPEG is the only encoder this driver +* supports. We will have to abstract this step, or get +* rid of the bounce buffer before we can support +* encoding other codecs. Hmm, why wouldn't it work for other encoders, which shouldn't require a bounce buffer?
Well, I had a TODO item to remove the bounce buffer for JPEG.
IIRC, the ChromeOS VPU driver doesn't have any bounce buffer, so I was under the impression we wouldn't need one.
However, we have yet to discuss the encoder implementation. We might decide to produce the headers for some video coded format, in which case we might need a bounce buffer.
In any case, this is just a comment to reflect that this piece of code is just temporary.
Quoted 20 lines
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +3
-1+*/ +if (ctx->jpeg_enc_ctx.bounce_buffer.cpu) {memcpy (vb2_plane_vaddr (&dst->vb2_buf,0 ) + ctx->vpu_dst_fmt->header_size, - ctx->bounce_buf, bytesused); + ctx->jpeg_enc_ctx.bounce_buffer.cpu, bytesused); } dst->vb2_buf.planes[0 ].bytesused = ctx->vpu_dst_fmt->header_size + bytesused;[snip]
Quoted 7 lines
/**
* structrockchip_vpu_codec_ops- codec mode specific operations *+ * @start: If needed, can be used for initialization. + * Optional and called from process context. + * @stop: If needed, can be used to undo the .start phase. + * Optional and called from process context.
Quoted 3 lines
nit: Perhaps .init and .exit could reflect better what these ops do?
Yeah, that'd be better.
Thanks for the feedback,
Eze
Re: [PATCH v2 06/11] rockchip/vpu: Cleanup JPEG bounce buffer management
Quoted 59 lines · Ezequiel Garcia
Quoted 45 lines · Tomasz Figa
Hi Ezequiel,
Quoted 5 lines · Ezequiel Garcia
In order to make the code more generic, introduce a pair of start/stop codec operations, and use them to allocate and release the JPEG bounce buffer.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>Quoted 12 lines
--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3288_vpu_hw_jpeg_enc.c | 4 +-- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 ++ .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 4 +-- .../staging/media/rockchip/vpu/rockchip_vpu.h | 12 ++++---- .../media/rockchip/vpu/rockchip_vpu_drv.c | 10 +++++-- .../media/rockchip/vpu/rockchip_vpu_enc.c | 23 +++++---------- .../media/rockchip/vpu/rockchip_vpu_hw.h | 28 +++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_jpeg.c | 25 +++++++++++++++++ 9 files changed, 81 insertions(+), 29 deletions(-)Thanks for the series! Really sorry for late reply...
[snip]
Quoted 20 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-4@@ -124,10 +124,7 @@ struct rockchip_vpu_dev {* @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. -* -* @bounce_dma_addr: Bounce buffer bus address. -* @bounce_buf: Bounce buffer pointer. -* @bounce_size: Bounce buffer size. +* @jpeg_enc_ctx: JPEG-encoding context. */ struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;@@ -146,9 +143,10 @@ struct rockchip_vpu_ctx {const struct rockchip_vpu_codec_ops *codec_ops;Quoted 11 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h struct rockchip_vpu_ctx { · line 149
Quoted 7 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +4
-3-dma_addr_t bounce_dma_addr; -void *bounce_buf; -size_t bounce_size; +/* Specific for particular codec modes. */ +union { +struct rockchip_vpu_jpeg_enc_hw_ctx jpeg_enc_ctx; + };nit: Would it perhaps make it a bit cleaner to call the union "ctx"? Then we wouldn't need to repeat "
_ctx" in every field.
Quoted 8 lines
Well, the struct is already
rockchip_vpu_ctx, so access would look like:ctx->ctx.jpeg_enc, ctx->ctx.mpeg2_decPerhaps we can just drop the
_ctx, and so:ctx->jpeg_enc, ctx->mpeg2_dec
Even better, thanks.
Quoted 22 lines
Quoted 12 lines
Quoted 12 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +0
-0};/** drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-1@@ -64,10 +64,16 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size;if (bytesused <= avail_size) { -if (ctx->bounce_buf) {Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, · line 71
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-0+/* +* This works while JPEG is the only encoder this driver +* supports. We will have to abstract this step, or get +* rid of the bounce buffer before we can support +* encoding other codecs. Hmm, why wouldn't it work for other encoders, which shouldn't require a bounce buffer?
Quoted 8 lines
Well, I had a TODO item to remove the bounce buffer for JPEG.
IIRC, the ChromeOS VPU driver doesn't have any bounce buffer, so I was under the impression we wouldn't need one.
However, we have yet to discuss the encoder implementation. We might decide to produce the headers for some video coded format, in which case we might need a bounce buffer.
We don't really need a bounce buffer to handle headers, we can do a memmove() instead, as we did for the VP8 encoder [1]. However, it was more like a loopback - the driver would just copy the header that the userspace set through a control, so we decided to drop it and move completely to the userspace [2] for H.264.
[1] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/5bc4e95afddd1300368d0552b228824252bd789f/drivers/media/platform/rk3288-vpu/rk3288_vpu_hw_vp8e.c#52
[2] https://chromium.googlesource.com/chromiumos/third_party/libv4lplugins/+/5e6034258146af6be973fb6a5bb6b9d6e7489437/libv4l-rockchip_v2/libvepu/h264e/h264e.c#591
Quoted 4 lines
In any case, this is just a comment to reflect that this piece of code is just temporary.
My point is that the comment suggests that other encoders would be affected by this, which I don't believe is true, because the code explicitly checks if the bounce buffer pointer is non-NULL and for other encoders it would be NULL.
/*
* The bounce buffer is only for the JPEG encoder.
* TODO: Rework the JPEG encoder to eliminate the need
* for a bounce buffer.
*/
Best regards,
Tomasz
PATCH v2 7/11 rockchip/vpu: Open-code media controller register
In reply to Ezequiel GarciaIn preparation to support decoders, using a single memory-to-memory device, we need to roll our own media controller entities registration.
--- .../staging/media/rockchip/vpu/rockchip_vpu.h | 35 ++++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 181 ++++++++++++++++-- 2 files changed, 204 insertions(+), 12 deletions(-)
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +35 -0
@@ -71,6 +71,38 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, }; +/* +* struct rockchip_vpu_mc - media controller data +* +* @source: &struct media_entity pointer with the source entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @source_pad: &struct media_pad with the source pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink: &struct media_entity pointer with the sink entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink_pad: &struct media_pad with the sink pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @proc: &struct media_entity pointer with the M2M device itself. +* @proc_pads: &struct media_pad with the @proc pads. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @intf_devnode: &struct media_intf devnode pointer with the interface +* with controls the M2M device. +*/ +struct rockchip_vpu_mc { +struct media_entity *source; +struct media_pad source_pad; +struct media_entity sink; +struct media_pad sink_pad; +struct media_entity proc; +struct media_pad proc_pads[2 ]; +struct media_intf_devnode *intf_devnode; +}; +/** * struct rockchip_vpu_dev - driver data * @v4l2_dev: V4L2 device to register video devices for.
@@ -78,6 +110,8 @@ enum rockchip_vpu_codec_mode {* @mdev: media device associated to this device. * @vfd_enc: Video device for encoder. * @pdev: Pointer to VPU platform device. +* @mc: Array of media controller topology structs +* for encoder and decoder. * @dev: Pointer to device for convenient logging using * dev_ macros. * @clocks: Array of clock handles.
@@ -95,6 +129,7 @@ struct rockchip_vpu_dev {struct media_device mdev;struct video_device *vfd_enc;struct platform_device *pdev; +struct rockchip_vpu_mc mc[2 ];struct device *dev;struct clk_bulk_data clocks[ROCKCHIP_VPU_MAX_CLOCKS ];void __iomem *base;
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +169 -12
219 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v2 07/11] rockchip/vpu: Open-code media controller register
Quoted 15 lines · Ezequiel Garcia
In preparation to support decoders, using a single memory-to-memory device, we need to roll our own media controller entities registration.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../staging/media/rockchip/vpu/rockchip_vpu.h | 35 ++++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 181 ++++++++++++++++-- 2 files changed, 204 insertions(+), 12 deletions(-)drivers/staging/media/rockchip/vpu/rockchip_vpu.h +0
-0
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 79
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +6
-0@@ -71,6 +71,38 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, }; +/* +* struct rockchip_vpu_mc - media controller data +* +* @source: &struct media_entity pointer with the source entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller().
_register? (and few other places below)
But I'm really confused, because this patch exactly removes the uses of v4l2_m2m_(un)register_media_controller() in this driver.
Quoted 30 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +26
-0+* @source_pad: &struct media_pad with the source pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink: &struct media_entity pointer with the sink entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink_pad: &struct media_pad with the sink pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @proc: &struct media_entity pointer with the M2M device itself. +* @proc_pads: &struct media_pad with the @proc pads. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @intf_devnode: &struct media_intf devnode pointer with the interface +* with controls the M2M device. +*/ +struct rockchip_vpu_mc { +struct media_entity *source; +struct media_pad source_pad; +struct media_entity sink; +struct media_pad sink_pad; +struct media_entity proc; +struct media_pad proc_pads[2 ]; +struct media_intf_devnode *intf_devnode; +}; +/** * struct rockchip_vpu_dev - driver data * @v4l2_dev: V4L2 device to register video devices for.
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 113
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-0@@ -78,6 +110,8 @@ enum rockchip_vpu_codec_mode {* @mdev: media device associated to this device. * @vfd_enc: Video device for encoder. * @pdev: Pointer to VPU platform device. +* @mc: Array of media controller topology structs
Is it just me or there is something wrong with indentation here?
Quoted 53 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +2
-0+* for encoder and decoder. * @dev: Pointer to device for convenient logging using * dev_ macros. * @clocks: Array of clock handles. @@ -95,6 +129,7 @@ struct rockchip_vpu_dev {struct media_device mdev;struct video_device *vfd_enc;struct platform_device *pdev; +struct rockchip_vpu_mc mc[2 ];struct device *dev;struct clk_bulk_data clocks[ROCKCHIP_VPU_MAX_CLOCKS ];void __iomem *base;drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-10@@ -332,7 +332,7 @@ static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) {const struct of_device_id *match;struct video_device *vfd; -int function, ret; +int ret; match =of_match_node (of_rockchip_vpu_match, vpu->dev->of_node); vfd =video_device_alloc ();@@ -359,21 +359,169 @@ static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) }v4l2_info (&vpu->v4l2_dev,"registered as /dev/video%d\n" , vfd->num); - function =MEDIA_ENT_F_PROC_VIDEO_ENCODER ; - ret =v4l2_m2m_register_media_controller (vpu->m2m_dev, vfd, function); -if (ret) { -v4l2_err (&vpu->v4l2_dev,"Failed to init mem2mem media controller\n" ); - goto err_unreg_video; - }return 0 ; - -err_unreg_video: -video_unregister_device (vfd); err_free_dev:video_device_release (vfd);return ret; } +static int rockchip_vpu_register_entity (struct media_device *mdev, +struct media_entity *entity,const char *entity_name, +struct media_pad *pads,int num_pads,int function, +struct video_device *vdev) +{ +unsigned int len; +char *name; +int ret; +
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 386
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+ entity->obj_type =MEDIA_ENTITY_TYPE_BASE ; +if (function ==MEDIA_ENT_F_IO_V4L ) { + entity->info.dev.major =VIDEO_MAJOR ; + entity->info.dev.minor = vdev->minor; + } + len =strlen (vdev->name) +2 +strlen (entity_name); + name =kmalloc (len,GFP_KERNEL ); +if (!name) +return -ENOMEM ; +snprintf (name, len,"%s-%s" , vdev->name, entity_name);
How about using kasprintf()?
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 395
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +9
-0+ entity->name = name; + entity->function = function; + + ret =media_entity_pads_init (entity, num_pads, pads); +if (ret) +return ret; + ret =media_device_register_entity (mdev, entity); +if (ret) +return ret;
How about the memory allocated for entity->name?
Quoted 63 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +63
-0+ +return 0 ; +} + +static int rockchip_register_mc (struct media_device *mdev, +struct rockchip_vpu_mc *mc, +struct video_device *vdev, +int function) +{ +struct media_link *link; +int ret; + +/* Create the three encoder entities with their pads */ + mc->source = &vdev->entity; + mc->source_pad.flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, mc->source, +"source" , &mc->source_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) +return ret; + + mc->proc_pads[0 ].flags =MEDIA_PAD_FL_SINK ; + mc->proc_pads[1 ].flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, &mc->proc, +"proc" , mc->proc_pads,2 , function, vdev); +if (ret) + goto err_rel_entity0; + + mc->sink_pad.flags =MEDIA_PAD_FL_SINK ; + ret =rockchip_vpu_register_entity (mdev, &mc->sink, +"sink" , &mc->sink_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) + goto err_rel_entity1; + +/* Connect the three entities */ + ret =media_create_pad_link (mc->source,0 , &mc->proc,1 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rel_entity2; + + ret =media_create_pad_link (&mc->proc,0 , &mc->sink,0 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rm_links0; + +/* Create video interface */ + mc->intf_devnode =media_devnode_create (mdev, +MEDIA_INTF_T_V4L_VIDEO ,0 , +VIDEO_MAJOR , vdev->minor); +if (!mc->intf_devnode) { + ret = -ENOMEM ; + goto err_rm_links1; + } + +/* Connect the two DMA engines to the interface */ + link =media_create_intf_link (mc->source, + &mc->intf_devnode->intf, +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (!link) { + ret = -ENOMEM ; + goto err_rm_devnode; + } + + link = media_create_intf_link(&mc->sink,
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 468
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+ &mc->intf_devnode->intf, + MEDIA_LNK_FL_IMMUTABLE | MEDIA_LNK_FL_ENABLED); +if (!link) { + ret = -ENOMEM ; + goto err_rm_intf_link; + } +return 0 ; + +err_rm_intf_link: +media_remove_intf_links (&mc->intf_devnode->intf);
Do we need to explicitly remove the links here? The entity removal functions remove the links implicitly.
Quoted 29 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +29
-0+err_rm_devnode: +media_devnode_remove (mc->intf_devnode); +err_rm_links1: +media_entity_remove_links (&mc->sink); +err_rm_links0: +media_entity_remove_links (&mc->proc); +media_entity_remove_links (mc->source); +err_rel_entity2: +media_device_unregister_entity (&mc->proc); +kfree (mc->proc.name); +err_rel_entity1: +media_device_unregister_entity (&mc->sink); +kfree (mc->sink.name); +err_rel_entity0: +media_device_unregister_entity (mc->source); +kfree (mc->source->name); +return ret; +} + +static void rockchip_unregister_mc (struct rockchip_vpu_mc *mc) +{ +media_remove_intf_links (&mc->intf_devnode->intf); +media_devnode_remove (mc->intf_devnode); +media_entity_remove_links (mc->source); +media_entity_remove_links (&mc->sink); +media_entity_remove_links (&mc->proc); +media_device_unregister_entity (mc->source); +media_device_unregister_entity (&mc->sink); +media_device_unregister_entity (&mc->proc);
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 507
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+kfree (mc->source->name); +kfree (mc->sink.name); +kfree (mc->proc.name); +} + +static int rockchip_register_media_controller (struct rockchip_vpu_dev *vpu) +{ +int ret; + +/* We have one memory-to-memory device, to hold a single queue
Coding style:
/*
* We have one [...]
Best regards,
Tomasz
Re: [PATCH v2 07/11] rockchip/vpu: Open-code media controller register
Quoted 27 lines · Tomasz Figa
Quoted 14 lines · Ezequiel Garcia
In preparation to support decoders, using a single memory-to-memory device, we need to roll our own media controller entities registration.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../staging/media/rockchip/vpu/rockchip_vpu.h | 35 ++++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 181 ++++++++++++++++-- 2 files changed, 204 insertions(+), 12 deletions(-)drivers/staging/media/rockchip/vpu/rockchip_vpu.h +0
-0drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 79
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +6
-0@@ -71,6 +71,38 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, }; +/* +* struct rockchip_vpu_mc - media controller data +* +* @source: &struct media_entity pointer with the source entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller().
_register? (and few other places below)
Quoted 3 lines
But I'm really confused, because this patch exactly removes the uses of v4l2_m2m_(un)register_media_controller() in this driver.
Those comments are bad copy paste, should be dropped.
Quoted 28 lines
Quoted 28 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +26
-0+* @source_pad: &struct media_pad with the source pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink: &struct media_entity pointer with the sink entity +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @sink_pad: &struct media_pad with the sink pad. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @proc: &struct media_entity pointer with the M2M device itself. +* @proc_pads: &struct media_pad with the @proc pads. +* Used only when the M2M device is registered via +* v4l2_m2m_unregister_media_controller(). +* @intf_devnode: &struct media_intf devnode pointer with the interface +* with controls the M2M device. +*/ +struct rockchip_vpu_mc { +struct media_entity *source; +struct media_pad source_pad; +struct media_entity sink; +struct media_pad sink_pad; +struct media_entity proc; +struct media_pad proc_pads[2 ]; +struct media_intf_devnode *intf_devnode; +}; +/** * struct rockchip_vpu_dev - driver data
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 113
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-0* @v4l2_dev: V4L2 device to register video devices for. @@ -78,6 +110,8 @@ enum rockchip_vpu_codec_mode {* @mdev: media device associated to this device. * @vfd_enc: Video device for encoder. * @pdev: Pointer to VPU platform device. +* @mc: Array of media controller topology structs Is it just me or there is something wrong with indentation here?
It seems to be fine here -- it's all tabs.
Quoted 57 lines
Quoted 57 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +2
-0+* for encoder and decoder. * @dev: Pointer to device for convenient logging using * dev_ macros. * @clocks: Array of clock handles. @@ -95,6 +129,7 @@ struct rockchip_vpu_dev {struct media_device mdev;struct video_device *vfd_enc;struct platform_device *pdev; +struct rockchip_vpu_mc mc[2 ];struct device *dev;struct clk_bulk_data clocks[ROCKCHIP_VPU_MAX_CLOCKS ];void __iomem *base;drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +14
-10@@ -332,7 +332,7 @@ static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) {const struct of_device_id *match;struct video_device *vfd; -int function, ret; +int ret; match =of_match_node (of_rockchip_vpu_match, vpu->dev->of_node); vfd =video_device_alloc ();@@ -359,21 +359,169 @@ static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) }v4l2_info (&vpu->v4l2_dev,"registered as /dev/video%d\n" , vfd->num); - function =MEDIA_ENT_F_PROC_VIDEO_ENCODER ; - ret =v4l2_m2m_register_media_controller (vpu->m2m_dev, vfd, function); -if (ret) { -v4l2_err (&vpu->v4l2_dev,"Failed to init mem2mem media controller\n" ); - goto err_unreg_video; - }return 0 ; - -err_unreg_video: -video_unregister_device (vfd); err_free_dev:video_device_release (vfd);return ret; } +static int rockchip_vpu_register_entity (struct media_device *mdev, +struct media_entity *entity,const char *entity_name, +struct media_pad *pads,int num_pads,int function, +struct video_device *vdev) +{ +unsigned int len; +char *name; +int ret; + + entity->obj_type =MEDIA_ENTITY_TYPE_BASE ; +if (function ==MEDIA_ENT_F_IO_V4L ) { + entity->info.dev.major =VIDEO_MAJOR ; + entity->info.dev.minor = vdev->minor;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 386
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +6
-0+ } + len =strlen (vdev->name) +2 +strlen (entity_name); + name =kmalloc (len,GFP_KERNEL ); +if (!name) +return -ENOMEM ; +snprintf (name, len,"%s-%s" , vdev->name, entity_name);How about using
kasprintf()?
Indeed.
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 395
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +9
-0+ entity->name = name; + entity->function = function; + + ret =media_entity_pads_init (entity, num_pads, pads); +if (ret) +return ret; + ret =media_device_register_entity (mdev, entity); +if (ret) +return ret;
Quoted 2 lines
How about the memory allocated for
entity->name?
Oops.
Quoted 68 lines
Quoted 68 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +68
-0+ +return 0 ; +} + +static int rockchip_register_mc (struct media_device *mdev, +struct rockchip_vpu_mc *mc, +struct video_device *vdev, +int function) +{ +struct media_link *link; +int ret; + +/* Create the three encoder entities with their pads */ + mc->source = &vdev->entity; + mc->source_pad.flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, mc->source, +"source" , &mc->source_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) +return ret; + + mc->proc_pads[0 ].flags =MEDIA_PAD_FL_SINK ; + mc->proc_pads[1 ].flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, &mc->proc, +"proc" , mc->proc_pads,2 , function, vdev); +if (ret) + goto err_rel_entity0; + + mc->sink_pad.flags =MEDIA_PAD_FL_SINK ; + ret =rockchip_vpu_register_entity (mdev, &mc->sink, +"sink" , &mc->sink_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) + goto err_rel_entity1; + +/* Connect the three entities */ + ret =media_create_pad_link (mc->source,0 , &mc->proc,1 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rel_entity2; + + ret =media_create_pad_link (&mc->proc,0 , &mc->sink,0 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rm_links0; + +/* Create video interface */ + mc->intf_devnode =media_devnode_create (mdev, +MEDIA_INTF_T_V4L_VIDEO ,0 , +VIDEO_MAJOR , vdev->minor); +if (!mc->intf_devnode) { + ret = -ENOMEM ; + goto err_rm_links1; + } + +/* Connect the two DMA engines to the interface */ + link =media_create_intf_link (mc->source, + &mc->intf_devnode->intf, +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (!link) { + ret = -ENOMEM ; + goto err_rm_devnode; + } + + link =media_create_intf_link (&mc->sink, + &mc->intf_devnode->intf, +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (!link) { + ret = -ENOMEM ; + goto err_rm_intf_link;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 468
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-0+ } +return 0 ; + +err_rm_intf_link: +media_remove_intf_links (&mc->intf_devnode->intf);Do we need to explicitly remove the links here? The entity removal functions remove the links implicitly.
You mean the media_devnode_remove, right? In that case, seems you are right.
Quoted 42 lines
Quoted 29 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +29
-0+err_rm_devnode: +media_devnode_remove (mc->intf_devnode); +err_rm_links1: +media_entity_remove_links (&mc->sink); +err_rm_links0: +media_entity_remove_links (&mc->proc); +media_entity_remove_links (mc->source); +err_rel_entity2: +media_device_unregister_entity (&mc->proc); +kfree (mc->proc.name); +err_rel_entity1: +media_device_unregister_entity (&mc->sink); +kfree (mc->sink.name); +err_rel_entity0: +media_device_unregister_entity (mc->source); +kfree (mc->source->name); +return ret; +} + +static void rockchip_unregister_mc (struct rockchip_vpu_mc *mc) +{ +media_remove_intf_links (&mc->intf_devnode->intf); +media_devnode_remove (mc->intf_devnode); +media_entity_remove_links (mc->source); +media_entity_remove_links (&mc->sink); +media_entity_remove_links (&mc->proc); +media_device_unregister_entity (mc->source); +media_device_unregister_entity (&mc->sink); +media_device_unregister_entity (&mc->proc);drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 507
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+kfree (mc->source->name); +kfree (mc->sink.name); +kfree (mc->proc.name); +} + +static int rockchip_register_media_controller (struct rockchip_vpu_dev *vpu) +{ +int ret; + +/* We have one memory-to-memory device, to hold a single queue Coding style:
Quoted 2 lines
/*
* We have one [...]
Right.
Thanks,
Eze
Re: [PATCH v2 07/11] rockchip/vpu: Open-code media controller register
Quoted 3 lines · Ezequiel Garcia
Quoted 1 line · Tomasz Figa
On Tue, Mar 5, 2019 at 4:27 AM Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]> wrote:
[snip]
Quoted 38 lines
Quoted 28 lines
Quoted 28 lines
+ * @source_pad: &struct
media_padwith the source pad.+ * Used only when the M2M device is registered via + * v4l2_m2m_unregister_media_controller(). + * @sink: &struct media_entity pointer with the sink entity + * Used only when the M2M device is registered via + * v4l2_m2m_unregister_media_controller(). + * @sink_pad: &struct media_pad with the sink pad. + * Used only when the M2M device is registered via + * v4l2_m2m_unregister_media_controller(). + * @proc: &struct media_entity pointer with the M2M device itself. + * @proc_pads: &struct media_pad with the @proc pads. + * Used only when the M2M device is registered via + * v4l2_m2m_unregister_media_controller(). + * @intf_devnode: &struct media_intf devnode pointer with the interface + * with controls the M2M device.+ */
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +10
-0+struct rockchip_vpu_mc { +struct media_entity *source; +struct media_pad source_pad; +struct media_entity sink; +struct media_pad sink_pad; +struct media_entity proc; +struct media_pad proc_pads[2 ]; +struct media_intf_devnode *intf_devnode; +}; +/** * struct rockchip_vpu_dev - driver data Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 113
Quoted 6 lines
* @v4l2_dev: V4L2 device to register video devices for.
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +1
-0@@ -78,6 +110,8 @@ enum rockchip_vpu_codec_mode {* @mdev: media device associated to this device. * @vfd_enc: Video device for encoder. * @pdev: Pointer to VPU platform device. +* @mc: Array of media controller topology structs Is it just me or there is something wrong with indentation here?
Quoted 1 line
It seems to be fine here -- it's all tabs.
Hmm, never mind then.
Quoted 78 lines
Quoted 68 lines
Quoted 68 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +68
-0+ +return 0 ; +} + +static int rockchip_register_mc (struct media_device *mdev, +struct rockchip_vpu_mc *mc, +struct video_device *vdev, +int function) +{ +struct media_link *link; +int ret; + +/* Create the three encoder entities with their pads */ + mc->source = &vdev->entity; + mc->source_pad.flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, mc->source, +"source" , &mc->source_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) +return ret; + + mc->proc_pads[0 ].flags =MEDIA_PAD_FL_SINK ; + mc->proc_pads[1 ].flags =MEDIA_PAD_FL_SOURCE ; + ret =rockchip_vpu_register_entity (mdev, &mc->proc, +"proc" , mc->proc_pads,2 , function, vdev); +if (ret) + goto err_rel_entity0; + + mc->sink_pad.flags =MEDIA_PAD_FL_SINK ; + ret =rockchip_vpu_register_entity (mdev, &mc->sink, +"sink" , &mc->sink_pad,1 ,MEDIA_ENT_F_IO_V4L , vdev); +if (ret) + goto err_rel_entity1; + +/* Connect the three entities */ + ret =media_create_pad_link (mc->source,0 , &mc->proc,1 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rel_entity2; + + ret =media_create_pad_link (&mc->proc,0 , &mc->sink,0 , +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (ret) + goto err_rm_links0; + +/* Create video interface */ + mc->intf_devnode =media_devnode_create (mdev, +MEDIA_INTF_T_V4L_VIDEO ,0 , +VIDEO_MAJOR , vdev->minor); +if (!mc->intf_devnode) { + ret = -ENOMEM ; + goto err_rm_links1; + } + +/* Connect the two DMA engines to the interface */ + link =media_create_intf_link (mc->source, + &mc->intf_devnode->intf, +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (!link) { + ret = -ENOMEM ; + goto err_rm_devnode; + } + + link =media_create_intf_link (&mc->sink, + &mc->intf_devnode->intf, +MEDIA_LNK_FL_IMMUTABLE |MEDIA_LNK_FL_ENABLED ); +if (!link) { + ret = -ENOMEM ; + goto err_rm_intf_link;Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_video_device_register(struct rockchip_vpu_dev *vpu) · line 468
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-0+ } +return 0 ; + +err_rm_intf_link: +media_remove_intf_links (&mc->intf_devnode->intf);Do we need to explicitly remove the links here? The entity removal functions remove the links implicitly.
Quoted 1 line
You mean the
media_devnode_remove, right? In that case, seems you are right.
Yep. And also media_device_unregister_entity().
Best regards,
Tomasz
PATCH v2 8/11 rockchip/vpu: Support the Request API
In reply to Ezequiel GarciaIntroduce support for the Request API. Although the JPEG encoder does not mandate using the Request API, it's perfectly possible to use it, if the application wants to.
In addition, add helpers that will be used by video decoders.
--- .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 6 ++++ .../media/rockchip/vpu/rockchip_vpu_common.h | 3 ++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 29 ++++++++++++++++++- .../media/rockchip/vpu/rockchip_vpu_enc.c | 18 ++++++++++++ 4 files changed, 55 insertions(+), 1 deletion(-)
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c +6 -0
@@ -113,11 +113,15 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx)struct rockchip_vpu_dev *vpu = ctx->dev;struct vb2_v4l2_buffer *src_buf, *dst_buf;struct rockchip_vpu_jpeg_ctx jpeg_ctx; +struct media_request *src_req;u32 reg; src_buf =v4l2_m2m_next_src_buf (ctx->fh.m2m_ctx); dst_buf =v4l2_m2m_next_dst_buf (ctx->fh.m2m_ctx); + src_req = src_buf->vb2_buf.req_obj.req; +v4l2_ctrl_request_setup (src_req, &ctx->ctrl_handler); +memset (&jpeg_ctx,0 ,sizeof (jpeg_ctx)); jpeg_ctx.buffer =vb2_plane_vaddr (&dst_buf->vb2_buf,0 ); jpeg_ctx.width = ctx->dst_fmt.width;
@@ -153,6 +157,8 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx) | VEPU_REG_ENCODE_FORMAT_JPEG |VEPU_REG_ENCODE_ENABLE ; +v4l2_ctrl_request_complete (src_req, &ctx->ctrl_handler); +/* Kick the watchdog and start encoding */ schedule_delayed_work (&vpu->watchdog_work,msecs_to_jiffies (2000 ));vepu_write (vpu, reg,VEPU_REG_ENCODE_START );
drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +3 -0
@@ -26,4 +26,7 @@ void rockchip_vpu_enc_reset_src_fmt(struct rockchip_vpu_dev *vpu,void rockchip_vpu_enc_reset_dst_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id); +dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts); +#endif /* ROCKCHIP_VPU_COMMON_H_ */
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +28 -1
@@ -36,6 +36,24 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" ); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id) +{ +struct v4l2_ctrl *ctrl; + + ctrl =v4l2_ctrl_find (&ctx->ctrl_handler, id); +return ctrl ? ctrl->p_cur.p :NULL ; +} + +dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts) +{ +int index; + + index =vb2_find_timestamp (q, ts,0 ); +if (index >=0 ) +return vb2_dma_contig_plane_dma_addr (q->bufs[index],0 ); +return 0 ; +} + static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, struct rockchip_vpu_ctx *ctx, unsigned int bytesused,
@@ -164,6 +182,7 @@ enc_queue_init(void *priv, struct vb2_queue *src_vq, struct vb2_queue *dst_vq) src_vq->timestamp_flags =V4L2_BUF_FLAG_TIMESTAMP_COPY ; src_vq->lock = &ctx->dev->vpu_mutex; src_vq->dev = ctx->dev->v4l2_dev.dev; + src_vq->supports_requests = true; ret =vb2_queue_init (src_vq);if (ret)
@@ -328,6 +347,11 @@ static const struct of_device_id of_rockchip_vpu_match[] = { };MODULE_DEVICE_TABLE (of, of_rockchip_vpu_match); +static const struct media_device_ops rockchip_m2m_media_ops = { + .req_validate = vb2_request_validate, + .req_queue = v4l2_m2m_request_queue, +}; +static int rockchip_vpu_video_device_register (struct rockchip_vpu_dev *vpu) {const struct of_device_id *match;
@@ -610,8 +634,11 @@ static int rockchip_vpu_probe(struct platform_device *pdev) } vpu->mdev.dev = vpu->dev; -strlcpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.bus_info,"platform:" DRIVER_NAME , +sizeof (vpu->mdev.bus_info));media_device_init (&vpu->mdev); + vpu->mdev.ops = &rockchip_m2m_media_ops; vpu->v4l2_dev.mdev = &vpu->mdev; ret =rockchip_vpu_video_device_register (vpu);
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +18 -0
@@ -555,14 +555,32 @@ static void rockchip_vpu_stop_streaming(struct vb2_queue *q) vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx);if (!vbuf)break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler);v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); } } +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} + +static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ; +return 0 ; +} +const struct vb2_ops rockchip_vpu_enc_queue_ops = { .queue_setup = rockchip_vpu_queue_setup, .buf_prepare = rockchip_vpu_buf_prepare, .buf_queue = rockchip_vpu_buf_queue, + .buf_out_validate = rockchip_vpu_buf_out_validate, + .buf_request_complete = rockchip_vpu_buf_request_complete, .start_streaming = rockchip_vpu_start_streaming, .stop_streaming = rockchip_vpu_stop_streaming, .wait_prepare = vb2_ops_wait_prepare,
Signature · 1 line
2.20.1
Re: [PATCH v2 08/11] rockchip/vpu: Support the Request API
Quoted 72 lines · Ezequiel Garcia
Introduce support for the Request API. Although the JPEG encoder does not mandate using the Request API, it's perfectly possible to use it, if the application wants to.
In addition, add helpers that will be used by video decoders.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 6 ++++ .../media/rockchip/vpu/rockchip_vpu_common.h | 3 ++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 29 ++++++++++++++++++- .../media/rockchip/vpu/rockchip_vpu_enc.c | 18 ++++++++++++ 4 files changed, 55 insertions(+), 1 deletion(-)drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c +6
-0@@ -113,11 +113,15 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx)struct rockchip_vpu_dev *vpu = ctx->dev;struct vb2_v4l2_buffer *src_buf, *dst_buf;struct rockchip_vpu_jpeg_ctx jpeg_ctx; +struct media_request *src_req;u32 reg; src_buf =v4l2_m2m_next_src_buf (ctx->fh.m2m_ctx); dst_buf =v4l2_m2m_next_dst_buf (ctx->fh.m2m_ctx); + src_req = src_buf->vb2_buf.req_obj.req; +v4l2_ctrl_request_setup (src_req, &ctx->ctrl_handler); +memset (&jpeg_ctx,0 ,sizeof (jpeg_ctx)); jpeg_ctx.buffer =vb2_plane_vaddr (&dst_buf->vb2_buf,0 ); jpeg_ctx.width = ctx->dst_fmt.width;@@ -153,6 +157,8 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx) | VEPU_REG_ENCODE_FORMAT_JPEG |VEPU_REG_ENCODE_ENABLE ; +v4l2_ctrl_request_complete (src_req, &ctx->ctrl_handler); +/* Kick the watchdog and start encoding */ schedule_delayed_work (&vpu->watchdog_work,msecs_to_jiffies (2000 ));vepu_write (vpu, reg,VEPU_REG_ENCODE_START );drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +3
-0@@ -26,4 +26,7 @@ void rockchip_vpu_enc_reset_src_fmt(struct rockchip_vpu_dev *vpu,void rockchip_vpu_enc_reset_dst_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id); +dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts); +#endif /* ROCKCHIP_VPU_COMMON_H_ */ drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +8
-0@@ -36,6 +36,24 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" ); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id) +{ +struct v4l2_ctrl *ctrl; + + ctrl =v4l2_ctrl_find (&ctx->ctrl_handler, id); +return ctrl ? ctrl->p_cur.p :NULL ; +} +
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c module_param_named(debug, rockchip_vpu_debug, int, 0644); · line 56
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts) +{ +int index; + + index =vb2_find_timestamp (q, ts,0 ); +if (index >=0 ) +return vb2_dma_contig_plane_dma_addr (q->bufs[index],0 ); +return 0 ; +} +
Hmm, I assume these 2 are the "helpers that will be used by video decoders"? Probably overly nitpicking, but these are relatively small, so why couldn't they be just added in the patch that actually adds the code using them? Otherwise, if for some reason we separate the series, we end up with dead code.
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +6
-0static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, struct rockchip_vpu_ctx *ctx, unsigned int bytesused,@@ -164,6 +182,7 @@ enc_queue_init(void *priv, struct vb2_queue *src_vq, struct vb2_queue *dst_vq) src_vq->timestamp_flags =V4L2_BUF_FLAG_TIMESTAMP_COPY ; src_vq->lock = &ctx->dev->vpu_mutex; src_vq->dev = ctx->dev->v4l2_dev.dev; + src_vq->supports_requests = true; ret =vb2_queue_init (src_vq);if (ret)@@ -328,6 +347,11 @@ static const struct of_device_id of_rockchip_vpu_match[] = { };MODULE_DEVICE_TABLE (of, of_rockchip_vpu_match); +static const struct media_device_ops rockchip_m2m_media_ops = { + .req_validate = vb2_request_validate, + .req_queue = v4l2_m2m_request_queue, +}; +static int rockchip_vpu_video_device_register (struct rockchip_vpu_dev *vpu) {const struct of_device_id *match;
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_probe(struct platform_device *pdev) · line 639
Quoted 7 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +3
-1@@ -610,8 +634,11 @@ static int rockchip_vpu_probe(struct platform_device *pdev) } vpu->mdev.dev = vpu->dev; -strlcpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.bus_info,"platform:" DRIVER_NAME , +sizeof (vpu->mdev.bus_info));
Unrelated changes?
Quoted 20 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +1
-0media_device_init (&vpu->mdev); + vpu->mdev.ops = &rockchip_m2m_media_ops; vpu->v4l2_dev.mdev = &vpu->mdev; ret =rockchip_vpu_video_device_register (vpu);drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +3
-0@@ -555,14 +555,32 @@ static void rockchip_vpu_stop_streaming(struct vb2_queue *q) vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx);if (!vbuf)break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler);v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); } } +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c static void rockchip_vpu_stop_streaming(struct vb2_queue *q) · line 574
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +10
-0+struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} + +static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;
Hmm, "validate" in the name of this callback would suggest that we should just check the contents, not change them. Hans, what was the intention when adding this callback? Are we missing the const specifier in the argument?
Best regards,
Tomasz
Re: [PATCH v2 08/11] rockchip/vpu: Support the Request API
On 3/28/19 8:20 AM, Tomasz Figa wrote:
<snip>
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c static void rockchip_vpu_stop_streaming(struct vb2_queue *q) · line 574
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +5
-0+static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;Hmm, "validate" in the name of this callback would suggest that we should just check the contents, not change them. Hans, what was the intention when adding this callback? Are we missing the const specifier in the argument?
See the original commit log:
https://www.mail-archive.com/[email protected]/msg143163.html
It is allowed to either just validate and return an error if wrong, or change it to something known to be valid. In particular, userspace can set this to FIELD_ANY, and in that case the driver must replace it with something valid.
Most drivers just support FIELD_NONE, and just set it.
That said, I think we should tighten the spec for this as this is not well documented.
I propose that if vbuf->field == FIELD_ANY, then replace it with something sane. Otherwise validate it and return an error if the field value is not supported.
And FIELD_ALTERNATE is never allowed here, that's always wrong.
Regards,
Hans
Re: [PATCH v2 08/11] rockchip/vpu: Support the Request API
Quoted 27 lines · Hans Verkuil
On 3/28/19 8:20 AM, Tomasz Figa wrote:
<snip>
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c static void rockchip_vpu_stop_streaming(struct vb2_queue *q) · line 574
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +5
-0+static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;Hmm, "validate" in the name of this callback would suggest that we should just check the contents, not change them. Hans, what was the intention when adding this callback? Are we missing the const specifier in the argument?
See the original commit log:
https://www.mail-archive.com/[email protected]/msg143163.html
It is allowed to either just validate and return an error if wrong, or change it to something known to be valid. In particular, userspace can set this to
FIELD_ANY, and in that case the driver must replace it with something valid.Most drivers just support
FIELD_NONE, and just set it.
Quoted 8 lines
That said, I think we should tighten the spec for this as this is not well documented.
I propose that if
vbuf->field==FIELD_ANY, then replace it with something sane. Otherwise validate it and return an error if the field value is not supported.And
FIELD_ALTERNATEis never allowed here, that's always wrong.
Thanks for clarifying. Makes sense.
Best regards,
Tomasz
Re: [PATCH v2 08/11] rockchip/vpu: Support the Request API
In reply to Tomasz FigaQuoted 80 lines · Tomasz Figa
Quoted 79 lines · Ezequiel Garcia
Introduce support for the Request API. Although the JPEG encoder does not mandate using the Request API, it's perfectly possible to use it, if the application wants to.
In addition, add helpers that will be used by video decoders.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c | 6 ++++ .../media/rockchip/vpu/rockchip_vpu_common.h | 3 ++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 29 ++++++++++++++++++- .../media/rockchip/vpu/rockchip_vpu_enc.c | 18 ++++++++++++ 4 files changed, 55 insertions(+), 1 deletion(-)drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_jpeg_enc.c +6
-0@@ -113,11 +113,15 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx)struct rockchip_vpu_dev *vpu = ctx->dev;struct vb2_v4l2_buffer *src_buf, *dst_buf;struct rockchip_vpu_jpeg_ctx jpeg_ctx; +struct media_request *src_req;u32 reg; src_buf =v4l2_m2m_next_src_buf (ctx->fh.m2m_ctx); dst_buf =v4l2_m2m_next_dst_buf (ctx->fh.m2m_ctx); + src_req = src_buf->vb2_buf.req_obj.req; +v4l2_ctrl_request_setup (src_req, &ctx->ctrl_handler); +memset (&jpeg_ctx,0 ,sizeof (jpeg_ctx)); jpeg_ctx.buffer =vb2_plane_vaddr (&dst_buf->vb2_buf,0 ); jpeg_ctx.width = ctx->dst_fmt.width;@@ -153,6 +157,8 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx) | VEPU_REG_ENCODE_FORMAT_JPEG |VEPU_REG_ENCODE_ENABLE ; +v4l2_ctrl_request_complete (src_req, &ctx->ctrl_handler); +/* Kick the watchdog and start encoding */ schedule_delayed_work (&vpu->watchdog_work,msecs_to_jiffies (2000 ));vepu_write (vpu, reg,VEPU_REG_ENCODE_START );drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +3
-0@@ -26,4 +26,7 @@ void rockchip_vpu_enc_reset_src_fmt(struct rockchip_vpu_dev *vpu,void rockchip_vpu_enc_reset_dst_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id); +dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts); +#endif /* ROCKCHIP_VPU_COMMON_H_ */ drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +16
-0@@ -36,6 +36,24 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" ); +void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id) +{ +struct v4l2_ctrl *ctrl; + + ctrl =v4l2_ctrl_find (&ctx->ctrl_handler, id); +return ctrl ? ctrl->p_cur.p :NULL ; +} + +dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts) +{ +int index; + + index =vb2_find_timestamp (q, ts,0 ); +if (index >=0 ) +return vb2_dma_contig_plane_dma_addr (q->bufs[index],0 ); +return 0 ;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c module_param_named(debug, rockchip_vpu_debug, int, 0644); · line 56
Quoted 2 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +2
-0+} +Hmm, I assume these 2 are the "helpers that will be used by video decoders"? Probably overly nitpicking, but these are relatively small, so why couldn't they be just added in the patch that actually adds the code using them? Otherwise, if for some reason we separate the series, we end up with dead code.
I can't remember why these are here. It was obviously intentional, as the commit log shows!
Anyway, yeah, I'll move them to the patch that makes use of it.
Quoted 26 lines
Quoted 26 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +6
-0static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, struct rockchip_vpu_ctx *ctx, unsigned int bytesused,@@ -164,6 +182,7 @@ enc_queue_init(void *priv, struct vb2_queue *src_vq, struct vb2_queue *dst_vq) src_vq->timestamp_flags =V4L2_BUF_FLAG_TIMESTAMP_COPY ; src_vq->lock = &ctx->dev->vpu_mutex; src_vq->dev = ctx->dev->v4l2_dev.dev; + src_vq->supports_requests = true; ret =vb2_queue_init (src_vq);if (ret)@@ -328,6 +347,11 @@ static const struct of_device_id of_rockchip_vpu_match[] = { };MODULE_DEVICE_TABLE (of, of_rockchip_vpu_match); +static const struct media_device_ops rockchip_m2m_media_ops = { + .req_validate = vb2_request_validate, + .req_queue = v4l2_m2m_request_queue, +}; +static int rockchip_vpu_video_device_register (struct rockchip_vpu_dev *vpu) {const struct of_device_id *match;@@ -610,8 +634,11 @@ static int rockchip_vpu_probe(struct platform_device *pdev) }
Quoted 8 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_probe(struct platform_device *pdev) · line 639
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +3
-1vpu->mdev.dev = vpu->dev; -strlcpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.model,DRIVER_NAME ,sizeof (vpu->mdev.model)); +strscpy (vpu->mdev.bus_info,"platform:" DRIVER_NAME , +sizeof (vpu->mdev.bus_info));Unrelated changes?
Totally.
Quoted 27 lines
Quoted 27 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +1
-0media_device_init (&vpu->mdev); + vpu->mdev.ops = &rockchip_m2m_media_ops; vpu->v4l2_dev.mdev = &vpu->mdev; ret =rockchip_vpu_video_device_register (vpu);drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +10
-0@@ -555,14 +555,32 @@ static void rockchip_vpu_stop_streaming(struct vb2_queue *q) vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx);if (!vbuf)break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler);v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); } } +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} + +static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c static void rockchip_vpu_stop_streaming(struct vb2_queue *q) · line 574
Quoted 3 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_enc.c +3
-0+struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;Hmm, "validate" in the name of this callback would suggest that we should just check the contents, not change them. Hans, what was the intention when adding this callback? Are we missing the const specifier in the argument?
Hans already replied to this.
Thanks,
Eze
PATCH v2 9/11 rockchip/vpu: Add decoder boilerplate
In reply to Ezequiel GarciaThis commit adds the needed boilerplate code to support the VPU in decoding operation. Two v4l2 interfaces are exposed, one for encoding and one for decoding, but a single m2m device is shared by them, so jobs are properly serialized.
--- drivers/staging/media/rockchip/vpu/Makefile | 1 + .../media/rockchip/vpu/rk3399_vpu_hw.c | 19 + .../staging/media/rockchip/vpu/rockchip_vpu.h | 35 ++ .../media/rockchip/vpu/rockchip_vpu_common.h | 6 + .../media/rockchip/vpu/rockchip_vpu_dec.c | 558 ++++++++++++++++++ .../media/rockchip/vpu/rockchip_vpu_drv.c | 136 ++++- 6 files changed, 743 insertions(+), 12 deletions(-) create mode 100644 drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c
drivers/staging/media/rockchip/vpu/Makefile +1 -0
@@ -3,6 +3,7 @@ obj-$(CONFIG_VIDEO_ROCKCHIP_VPU) += rockchip-vpu.o rockchip-vpu-y += \ rockchip_vpu_drv.o \ rockchip_vpu_enc.o \ + rockchip_vpu_dec.o \ rk3288_vpu_hw.o \ rk3288_vpu_hw_jpeg_enc.o \ rk3399_vpu_hw.o \
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +19 -0
@@ -74,6 +74,24 @@ static irqreturn_t rk3399_vepu_irq(int irq, void *dev_id)return IRQ_HANDLED ; } +static irqreturn_t rk3399_vdpu_irq (int irq,void *dev_id) +{ +struct rockchip_vpu_dev *vpu = dev_id; +enum vb2_buffer_state state; +u32 status; + + status =vdpu_read (vpu,VDPU_REG_INTERRUPT ); + state = (status &VDPU_REG_INTERRUPT_DEC_IRQ ) ? +VB2_BUF_STATE_DONE :VB2_BUF_STATE_ERROR ; + +vdpu_write (vpu,0 ,VDPU_REG_INTERRUPT ); +vdpu_write (vpu,0 ,VDPU_REG_AXI_CTRL ); + +rockchip_vpu_irq_done (vpu,0 , state); + +return IRQ_HANDLED ; +} +static int rk3399_vpu_hw_init (struct rockchip_vpu_dev *vpu) {/* Bump ACLK to max. possible freq. to improve performance. */
@@ -114,6 +132,7 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .codec = RK_VPU_CODEC_JPEG, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, + .vdpu_irq = rk3399_vdpu_irq, .init = rk3399_vpu_hw_init, .clk_names = {"aclk", "hclk"}, .num_clocks = 2
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +35 -0
@@ -40,23 +40,31 @@ struct rockchip_vpu_codec_ops;* struct rockchip_vpu_variant - information about VPU hardware variant * * @enc_offset: Offset from VPU base to encoder registers. +* @dec_offset: Offset from VPU base to decoder registers. * @enc_fmts: Encoder formats. * @num_enc_fmts: Number of encoder formats. +* @dec_fmts: Decoder formats. +* @num_dec_fmts: Number of decoder formats. * @codec: Supported codecs * @codec_ops: Codec ops. * @init: Initialize hardware. * @vepu_irq: encoder interrupt handler +* @vdpu_irq: decoder interrupt handler * @clk_names: array of clock names * @num_clocks: number of clocks in the array */ struct rockchip_vpu_variant {unsigned int enc_offset; +unsigned int dec_offset;const struct rockchip_vpu_fmt *enc_fmts;unsigned int num_enc_fmts; +const struct rockchip_vpu_fmt *dec_fmts; +unsigned int num_dec_fmts;unsigned int codec;const struct rockchip_vpu_codec_ops *codec_ops;int (*init)(struct rockchip_vpu_dev *vpu);irqreturn_t (*vepu_irq)(int irq,void *priv); +irqreturn_t (*vdpu_irq)(int irq,void *priv);const char *clk_names[ROCKCHIP_VPU_MAX_CLOCKS ];int num_clocks; };
@@ -109,6 +117,7 @@ struct rockchip_vpu_mc {* @m2m_dev: mem2mem device associated to this device. * @mdev: media device associated to this device. * @vfd_enc: Video device for encoder. +* @vfd_dec: Video device for decoder. * @pdev: Pointer to VPU platform device. * @mc: Array of media controller topology structs * for encoder and decoder.
@@ -117,6 +126,7 @@ struct rockchip_vpu_mc {* @clocks: Array of clock handles. * @base: Mapped address of VPU registers. * @enc_base: Mapped address of VPU encoder register for convenience. +* @dec_base: Mapped address of VPU decoder register for convenience. * @vpu_mutex: Mutex to synchronize V4L2 calls. * @irqlock: Spinlock to synchronize access to data structures * shared with interrupt handlers.
@@ -128,12 +138,14 @@ struct rockchip_vpu_dev {struct v4l2_m2m_dev *m2m_dev;struct media_device mdev;struct video_device *vfd_enc; +struct video_device *vfd_dec;struct platform_device *pdev;struct rockchip_vpu_mc mc[2 ];struct device *dev;struct clk_bulk_data clocks[ROCKCHIP_VPU_MAX_CLOCKS ];void __iomem *base;void __iomem *enc_base; +void __iomem *dec_base;struct mutex vpu_mutex;/* video_device lock */ spinlock_t irqlock;
@@ -146,6 +158,7 @@ struct rockchip_vpu_dev {* * @dev: VPU driver data to which the context belongs. * @fh: V4L2 file handler. +* @is_enc: Encoder or decoder? * * @sequence_cap: Sequence counter for capture queue * @sequence_out: Sequence counter for output queue
@@ -164,6 +177,7 @@ struct rockchip_vpu_dev {struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;struct v4l2_fh fh; +unsigned int is_enc;u32 sequence_cap;u32 sequence_out;
@@ -262,4 +276,25 @@ static inline u32 vepu_read(struct rockchip_vpu_dev *vpu, u32 reg)return val; } +static inline void vdpu_write_relaxed (struct rockchip_vpu_dev *vpu, +u32 val,u32 reg) +{ +vpu_debug (6 ,"0x%04x = 0x%08x\n" , reg /4 , val); +writel_relaxed (val, vpu->dec_base + reg); +} + +static inline void vdpu_write (struct rockchip_vpu_dev *vpu,u32 val,u32 reg) +{ +vpu_debug (6 ,"0x%04x = 0x%08x\n" , reg /4 , val); +writel (val, vpu->dec_base + reg); +} + +static inline u32 vdpu_read (struct rockchip_vpu_dev *vpu,u32 reg) +{ +u32 val =readl (vpu->dec_base + reg); + +vpu_debug (6 ,"0x%04x = 0x%08x\n" , reg /4 , val); +return val; +} +#endif /* ROCKCHIP_VPU_H_ */
drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +6 -0
@@ -19,12 +19,18 @@#include "rockchip_vpu.h" extern const struct v4l2_ioctl_ops rockchip_vpu_enc_ioctl_ops; +extern const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops;extern const struct vb2_ops rockchip_vpu_enc_queue_ops; +extern const struct vb2_ops rockchip_vpu_dec_queue_ops;void rockchip_vpu_enc_reset_src_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx);void rockchip_vpu_enc_reset_dst_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); +void rockchip_vpu_dec_reset_src_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx); +void rockchip_vpu_dec_reset_dst_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx);void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id);dma_addr_t rockchip_vpu_get_ref (struct vb2_queue *q,u64 ts);
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +558 -0
558 lines not on this page · raw message
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +124 -12
224 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v2 09/11] rockchip/vpu: Add decoder boilerplate
On Tue, Mar 5, 2019 at 4:27 AM Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]> wrote:
[snip]
Quoted 52 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +52
-0+static const struct rockchip_vpu_fmt * +rockchip_vpu_find_format (struct rockchip_vpu_ctx *ctx,u32 fourcc) +{ +struct rockchip_vpu_dev *dev = ctx->dev; +const struct rockchip_vpu_fmt *formats; +unsigned int num_fmts, i; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) +if (formats[i].fourcc == fourcc) +return &formats[i]; +return NULL ; +} + +static const struct rockchip_vpu_fmt * +rockchip_vpu_get_default_fmt (struct rockchip_vpu_ctx *ctx,bool bitstream) +{ +struct rockchip_vpu_dev *dev = ctx->dev; +const struct rockchip_vpu_fmt *formats; +unsigned int num_fmts, i; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) +if (bitstream == (formats[i].codec_mode !=RK_VPU_MODE_NONE )) +return &formats[i]; +return NULL ; +} + +static int vidioc_querycap (struct file *file,void *priv, +struct v4l2_capability *cap) +{ +struct rockchip_vpu_dev *vpu =video_drvdata (file); + +strlcpy (cap->driver, vpu->dev->driver->name,sizeof (cap->driver)); +strlcpy (cap->card, vpu->vfd_dec->name,sizeof (cap->card)); +snprintf (cap->bus_info,sizeof (cap->bus_info),"platform: %s" , + vpu->dev->driver->name); +return 0 ; +} + +static int vidioc_enum_framesizes (struct file *file,void *priv, +struct v4l2_frmsizeenum *fsize) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +const struct rockchip_vpu_fmt *fmt; + +if (fsize->index !=0 ) { +vpu_debug (0 ,"invalid frame size index (expected 0, got %d)\n" , + fsize->index); +return -EINVAL ;
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 94
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ } + + fmt =rockchip_vpu_find_format (ctx, fsize->pixel_format); +if (!fmt) { +vpu_debug (0 ,"unsupported bitstream format (%08x)\n" , + fsize->pixel_format); +return -EINVAL ; + } + +/* This only makes sense for codec formats */
"coded formats"
Quoted 45 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +45
-0+if (fmt->codec_mode ==RK_VPU_MODE_NONE ) +return -EINVAL ; + + fsize->type =V4L2_FRMSIZE_TYPE_STEPWISE ; + fsize->stepwise = fmt->frmsize; + +return 0 ; +} + +static int vidioc_enum_fmt_vid_cap_mplane (struct file *file,void *priv, +struct v4l2_fmtdesc *f) +{ +struct rockchip_vpu_dev *dev =video_drvdata (file); +const struct rockchip_vpu_fmt *fmt; +const struct rockchip_vpu_fmt *formats; +int num_fmts, i, j =0 ; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) { +/* Skip compressed formats */ +if (formats[i].codec_mode !=RK_VPU_MODE_NONE ) +continue ; +if (j == f->index) { + fmt = &formats[i]; + f->pixelformat = fmt->fourcc; +return 0 ; + } + ++j; + } +return -EINVAL ; +} + +static int vidioc_enum_fmt_vid_out_mplane (struct file *file,void *priv, +struct v4l2_fmtdesc *f) +{ +struct rockchip_vpu_dev *dev =video_drvdata (file); +const struct rockchip_vpu_fmt *formats; +const struct rockchip_vpu_fmt *fmt; +int num_fmts, i, j =0 ; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) { +if (formats[i].codec_mode ==RK_VPU_MODE_NONE )
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 149
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+continue ; +if (j == f->index) { + fmt = &formats[i]; + f->pixelformat = fmt->fourcc; +return 0 ; + } + ++j; + } +return -EINVAL ; +}
All the functions above can be trivially generalized to be used for both encoder and decoder. Moreover, vidioc_enum_fmt_vid_{cap,out}_mplane() can be trivially merged into one function to cover both buffer types.
Quoted 110 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +110
-0+ +static int vidioc_g_fmt_out_mplane (struct file *file,void *priv, +struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); + +vpu_debug (4 ,"f->type = %d\n" , f->type); + + *pix_mp = ctx->src_fmt; + +return 0 ; +} + +static int vidioc_g_fmt_cap_mplane (struct file *file,void *priv, +struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); + +vpu_debug (4 ,"f->type = %d\n" , f->type); + + *pix_mp = ctx->dst_fmt; + +return 0 ; +} + +static int +vidioc_try_fmt_cap_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +const struct rockchip_vpu_fmt *fmt; +unsigned int width, height; + +vpu_debug (4 ,"%c%c%c%c\n" , + (pix_mp->pixelformat &0x7f ), + (pix_mp->pixelformat >>8 ) &0x7f , + (pix_mp->pixelformat >>16 ) &0x7f , + (pix_mp->pixelformat >>24 ) &0x7f ); + + fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); +if (!fmt) { + fmt =rockchip_vpu_get_default_fmt (ctx, false); + f->fmt.pix.pixelformat = fmt->fourcc; + } + + pix_mp->field =V4L2_FIELD_NONE ; + width =clamp (pix_mp->width, + ctx->vpu_src_fmt->frmsize.min_width, + ctx->vpu_src_fmt->frmsize.max_width); + height =clamp (pix_mp->height, + ctx->vpu_src_fmt->frmsize.min_height, + ctx->vpu_src_fmt->frmsize.max_height); +/* Round up to macroblocks. */ + width =round_up (width, ctx->vpu_src_fmt->frmsize.step_width); + height =round_up (height, ctx->vpu_src_fmt->frmsize.step_height); + +/* Fill remaining fields */ +v4l2_fill_pixfmt_mp (pix_mp, fmt->fourcc, width, height); +return 0 ; +} + +static int +vidioc_try_fmt_out_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +const struct rockchip_vpu_fmt *fmt; + + fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); +if (!fmt) { + fmt =rockchip_vpu_get_default_fmt (ctx, true); + f->fmt.pix.pixelformat = fmt->fourcc; + } + + pix_mp->num_planes =1 ; + pix_mp->field =V4L2_FIELD_NONE ; + pix_mp->width =clamp (pix_mp->width, + fmt->frmsize.min_width, + fmt->frmsize.max_width); + pix_mp->height =clamp (pix_mp->height, + fmt->frmsize.min_height, + fmt->frmsize.max_height); +/* Round up to macroblocks. */ + pix_mp->width =round_up (pix_mp->width, fmt->frmsize.step_width); + pix_mp->height =round_up (pix_mp->height, fmt->frmsize.step_height); + +/* +* For compressed formats the application can specify +* sizeimage. If the application passes a zero sizeimage, +* let's default to the maximum frame size. +*/ +if (!pix_mp->plane_fmt[0 ].sizeimage) + pix_mp->plane_fmt[0 ].sizeimage = fmt->header_size + + pix_mp->width * pix_mp->height * fmt->max_depth; +return 0 ; +} + +void rockchip_vpu_dec_reset_dst_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx) +{ +struct v4l2_pix_format_mplane *fmt = &ctx->dst_fmt; +unsigned int width, height; + + ctx->vpu_dst_fmt =rockchip_vpu_get_default_fmt (ctx, false); + +memset (fmt,0 ,sizeof (*fmt)); + + width = clamp(fmt->width, ctx->vpu_src_fmt->frmsize.min_width,
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 269
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ ctx->vpu_src_fmt->frmsize.max_width); + height =clamp (fmt->height, ctx->vpu_src_fmt->frmsize.min_height, + ctx->vpu_src_fmt->frmsize.max_height); + fmt->field =V4L2_FIELD_NONE ; + fmt->colorspace =V4L2_COLORSPACE_JPEG , + fmt->ycbcr_enc =V4L2_YCBCR_ENC_DEFAULT ; + fmt->quantization =V4L2_QUANTIZATION_DEFAULT ; + fmt->xfer_func =V4L2_XFER_FUNC_DEFAULT ; + +v4l2_fill_pixfmt_mp (fmt, ctx->vpu_dst_fmt->fourcc, width, height);
Rather than duplicating most of the work already done in vidioc_try_fmt_*(), could we just call it here?
Quoted 15 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +15
-0+} + +void rockchip_vpu_dec_reset_src_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx) +{ +struct v4l2_pix_format_mplane *fmt = &ctx->src_fmt; + + ctx->vpu_src_fmt =rockchip_vpu_get_default_fmt (ctx, true); + +memset (fmt,0 ,sizeof (*fmt)); + + fmt->num_planes =1 ; + fmt->width =clamp (fmt->width, ctx->vpu_src_fmt->frmsize.min_width, + ctx->vpu_src_fmt->frmsize.max_width); + fmt->height = clamp(fmt->height, ctx->vpu_src_fmt->frmsize.min_height,
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 294
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ ctx->vpu_src_fmt->frmsize.max_height); + fmt->pixelformat = ctx->vpu_src_fmt->fourcc; + fmt->field =V4L2_FIELD_NONE ; + fmt->colorspace =V4L2_COLORSPACE_JPEG , + fmt->ycbcr_enc =V4L2_YCBCR_ENC_DEFAULT ; + fmt->quantization =V4L2_QUANTIZATION_DEFAULT ; + fmt->xfer_func =V4L2_XFER_FUNC_DEFAULT ; + + fmt->plane_fmt[0 ].sizeimage = ctx->vpu_src_fmt->header_size + + fmt->width * fmt->height * ctx->vpu_src_fmt->max_depth;
Ditto.
Quoted 18 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +18
-0+} + +static int +vidioc_s_fmt_out_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct rockchip_vpu_dev *vpu = ctx->dev; +struct vb2_queue *vq, *peer_vq; +int ret; + +/* Change not allowed if queue is streaming. */ + vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, f->type); +if (vb2_is_streaming (vq)) +return -EBUSY ; + +/* +* Since format change on the OUTPUT queue will reset
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 322
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+* the CAPTURE queue, we can't allow doing so +* when the CAPTURE queue has buffers allocated. +*/ + peer_vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, +V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE ); +if (vb2_is_busy (peer_vq) && + (pix_mp->pixelformat != ctx->src_fmt.pixelformat || + pix_mp->height != ctx->src_fmt.height || + pix_mp->width != ctx->src_fmt.width)) +return -EBUSY ;
I'd say that in general we don't want any S_FMT(OUT) to be allowed if CAP has buffers allocated, so maybe just checking vb2_is_busy(peer_vq) is enough?
Quoted 81 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +81
-0+ + ret =vidioc_try_fmt_out_mplane (file, priv, f); +if (ret) +return ret; + + ctx->vpu_src_fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); + ctx->src_fmt = *pix_mp; + +vpu_debug (0 ,"OUTPUT codec mode: %d\n" , ctx->vpu_src_fmt->codec_mode); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height); + +rockchip_vpu_dec_reset_dst_fmt (vpu, ctx); +return 0 ; +} + +static int +vidioc_s_fmt_cap_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct vb2_queue *vq; +int ret; + +/* Change not allowed if queue is streaming. */ + vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, f->type); +if (vb2_is_streaming (vq)) +return -EBUSY ; + + ret =vidioc_try_fmt_cap_mplane (file, priv, f); +if (ret) +return ret; + + ctx->vpu_dst_fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); + ctx->dst_fmt = *pix_mp; + +vpu_debug (0 ,"CAPTURE codec mode: %d\n" , ctx->vpu_dst_fmt->codec_mode); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height); +return 0 ; +} + +const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops = { + .vidioc_querycap = vidioc_querycap, + .vidioc_enum_framesizes = vidioc_enum_framesizes, + + .vidioc_try_fmt_vid_cap_mplane = vidioc_try_fmt_cap_mplane, + .vidioc_try_fmt_vid_out_mplane = vidioc_try_fmt_out_mplane, + .vidioc_s_fmt_vid_out_mplane = vidioc_s_fmt_out_mplane, + .vidioc_s_fmt_vid_cap_mplane = vidioc_s_fmt_cap_mplane, + .vidioc_g_fmt_vid_out_mplane = vidioc_g_fmt_out_mplane, + .vidioc_g_fmt_vid_cap_mplane = vidioc_g_fmt_cap_mplane, + .vidioc_enum_fmt_vid_out_mplane = vidioc_enum_fmt_vid_out_mplane, + .vidioc_enum_fmt_vid_cap_mplane = vidioc_enum_fmt_vid_cap_mplane, + + .vidioc_reqbufs = v4l2_m2m_ioctl_reqbufs, + .vidioc_querybuf = v4l2_m2m_ioctl_querybuf, + .vidioc_qbuf = v4l2_m2m_ioctl_qbuf, + .vidioc_dqbuf = v4l2_m2m_ioctl_dqbuf, + .vidioc_prepare_buf = v4l2_m2m_ioctl_prepare_buf, + .vidioc_create_bufs = v4l2_m2m_ioctl_create_bufs, + .vidioc_expbuf = v4l2_m2m_ioctl_expbuf, + + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event, + .vidioc_unsubscribe_event = v4l2_event_unsubscribe, + + .vidioc_streamon = v4l2_m2m_ioctl_streamon, + .vidioc_streamoff = v4l2_m2m_ioctl_streamoff, +}; + +static int rockchip_vpu_queue_setup (struct vb2_queue *vq, +unsigned int *num_buffers, +unsigned int *num_planes, +unsigned int sizes[], +struct device *alloc_devs[]) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vq); +struct v4l2_pix_format_mplane *pixfmt; +int i; + +switch (vq->type) {
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 413
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE : + pixfmt = &ctx->dst_fmt; +break ; +case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE : + pixfmt = &ctx->src_fmt; +break ; +default : +vpu_err ("invalid queue type: %d\n" , vq->type); +return -EINVAL ; + }
Hmm, would it make sense to have separate vb2_queue_ops for each queue and create helper functions, which take the necessary queue-specific data as arguments, if appropriate?
Quoted 76 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +76
-0+ +if (*num_planes) { +if (*num_planes != pixfmt->num_planes) +return -EINVAL ; +for (i =0 ; i < pixfmt->num_planes; ++i) +if (sizes[i] < pixfmt->plane_fmt[i].sizeimage) +return -EINVAL ; +return 0 ; + } + + *num_planes = pixfmt->num_planes; +for (i =0 ; i < pixfmt->num_planes; ++i) + sizes[i] = pixfmt->plane_fmt[i].sizeimage; +return 0 ; +} + +static int rockchip_vpu_buf_prepare (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); +struct vb2_queue *vq = vb->vb2_queue; +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vq); +const struct rockchip_vpu_fmt *vpu_fmt; +struct v4l2_pix_format_mplane *pixfmt; +unsigned int sz; +int ret =0 ; +int i; + +switch (vq->type) { +case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE : + vpu_fmt = ctx->vpu_dst_fmt; + pixfmt = &ctx->dst_fmt; +break ; +case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE : + vpu_fmt = ctx->vpu_src_fmt; + pixfmt = &ctx->src_fmt; + +if (vbuf->field ==V4L2_FIELD_ANY ) + vbuf->field =V4L2_FIELD_NONE ; +if (vbuf->field !=V4L2_FIELD_NONE ) { +vpu_debug (4 ,"field %d not supported\n" , + vbuf->field); +return -EINVAL ; + } +break ; +default : +vpu_err ("invalid queue type: %d\n" , vq->type); +return -EINVAL ; + } + +for (i =0 ; i < pixfmt->num_planes; ++i) { + sz = pixfmt->plane_fmt[i].sizeimage; +vpu_debug (4 ,"plane %d size: %ld, sizeimage: %u\n" , + i,vb2_plane_size (vb, i), sz); +if (vb2_plane_size (vb, i) < sz) { +vpu_err ("plane %d is too small for output\n" , i); + ret = -EINVAL ; +break ; + } + } + +return ret; +} + +static void rockchip_vpu_buf_queue (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + +v4l2_m2m_buf_queue (ctx->fh.m2m_ctx, vbuf); +} + +static int rockchip_vpu_start_streaming (struct vb2_queue *q,unsigned int count) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q); +enum rockchip_vpu_codec_mode codec_mode; +int ret =0 ;
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 499
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) + ctx->sequence_out =0 ; +else + ctx->sequence_cap =0 ; + + codec_mode = ctx->vpu_src_fmt->codec_mode; + +vpu_debug (4 ,"Codec mode = %d\n" , codec_mode); + ctx->codec_ops = &ctx->dev->variant->codec_ops[codec_mode];
Codec mode should be a function of the OUT queue, so I think this should be also under if (V4L2_TYPE_IS_OUTPUT()). This would make most of the code in this function specific to the OUT queue and possibly a good argument for the comment about having separate vb2 queue ops I posted above.
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +6
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->start) + ret = ctx->codec_ops->start (ctx); +return ret; +}
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 515
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ +static void rockchip_vpu_stop_streaming (struct vb2_queue *q) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q); + +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->stop) + ctx->codec_ops->stop (ctx); + +/* The mem2mem framework calls v4l2_m2m_cancel_job before
CodingStyle: Multiline comments should start with one empty line.
Quoted 19 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +19
-0+* .stop_streaming, so there isn't any job running and +* it is safe to return all the buffers. +*/ +for (;;) { +struct vb2_v4l2_buffer *vbuf; + +if (V4L2_TYPE_IS_OUTPUT (q->type)) + vbuf =v4l2_m2m_src_buf_remove (ctx->fh.m2m_ctx); +else + vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx); +if (!vbuf) +break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler); +v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); + } +} + +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 544
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} + +static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;
Similar comment as in earlier patch. Is validate expected to correct the values or just check?
Quoted 19 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +14
-0+return 0 ; +} + +const struct vb2_ops rockchip_vpu_dec_queue_ops = { + .queue_setup = rockchip_vpu_queue_setup, + .buf_prepare = rockchip_vpu_buf_prepare, + .buf_queue = rockchip_vpu_buf_queue, + .buf_out_validate = rockchip_vpu_buf_out_validate, + .buf_request_complete = rockchip_vpu_buf_request_complete, + .start_streaming = rockchip_vpu_start_streaming, + .stop_streaming = rockchip_vpu_stop_streaming, + .wait_prepare = vb2_ops_wait_prepare, + .wait_finish = vb2_ops_wait_finish, +};drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c module_param_named(debug, rockchip_vpu_debug, int, 0644); · line 42
Quoted 7 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +4
-0@@ -36,6 +36,11 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" ); +enum rockchip_vpu_type { +RK_VPU_ENCODER , +RK_VPU_DECODER , +};
Given that we already have ctx->is_enc, any reason not to have this represented in the same way everywhere?
Quoted 7 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +1
-0+void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id) {struct v4l2_ctrl *ctrl;@@ -81,7 +86,11 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size = vb2_plane_size(&dst->vb2_buf, 0) -
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, · line 96
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-1ctx->vpu_dst_fmt->header_size; -if (bytesused <= avail_size) { +/* For decoders set bytesused as per the output picture. */ +if (!ctx->is_enc) { + dst->vb2_buf.planes[0 ].bytesused = + ctx->dst_fmt.plane_fmt[0 ].sizeimage; + }else if (bytesused <= avail_size) {/* * This works while JPEG is the only encoder this driver * supports. We will have to abstract this step, or get
avail_size is specific for the encoder. How about clearly separating decoder and encoder code with a separate if? It would introduce one more level of nesting, but IMHO it would be more readable, due to better separation of code paths. (Or going one step further, encoder and decoder-specific code could be moved to separate functions.)
if (ctx->is_enc) {
size_t avail_size = ...;
// encoder code
if (bytesused <= avail_size) {
//
} else {
// }
} else {
// decoder code
}
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +20
-0@@ -159,6 +168,44 @@ static struct v4l2_m2m_ops vpu_m2m_ops = { .device_run = device_run, }; +static int +dec_queue_init (void *priv,struct vb2_queue *src_vq,struct vb2_queue *dst_vq) +{ +struct rockchip_vpu_ctx *ctx = priv; +int ret; + + src_vq->type =V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE ; + src_vq->io_modes =VB2_MMAP |VB2_DMABUF ; + src_vq->drv_priv = ctx; + src_vq->ops = &rockchip_vpu_dec_queue_ops; + src_vq->mem_ops = &vb2_dma_contig_memops; + src_vq->dma_attrs =DMA_ATTR_ALLOC_SINGLE_PAGES | +DMA_ATTR_NO_KERNEL_MAPPING ; + src_vq->buf_struct_size =sizeof (struct v4l2_m2m_buffer ); + src_vq->timestamp_flags =V4L2_BUF_FLAG_TIMESTAMP_COPY ; + src_vq->lock = &ctx->dev->vpu_mutex; + src_vq->dev = ctx->dev->v4l2_dev.dev; + src_vq->supports_requests = true; + + ret =vb2_queue_init (src_vq);
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static struct v4l2_m2m_ops vpu_m2m_ops = { · line 200
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+if (ret) +return ret; + + dst_vq->type =V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE ; + dst_vq->io_modes =VB2_MMAP |VB2_DMABUF ; + dst_vq->drv_priv = ctx; + dst_vq->bidirectional = true; + dst_vq->ops = &rockchip_vpu_dec_queue_ops; + dst_vq->mem_ops = &vb2_dma_contig_memops; + dst_vq->dma_attrs =DMA_ATTR_ALLOC_SINGLE_PAGES ;
Any need for kernel mapping of decoder output?
Best regards,
Tomasz
Re: [PATCH v2 09/11] rockchip/vpu: Add decoder boilerplate
Hey Tomasz,
Thanks for taking the time to review this carefully!
Quoted 58 lines · Tomasz Figa
On Tue, Mar 5, 2019 at 4:27 AM Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]> wrote:
[snip]Quoted 56 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +56
-0+static const struct rockchip_vpu_fmt * +rockchip_vpu_find_format (struct rockchip_vpu_ctx *ctx,u32 fourcc) +{ +struct rockchip_vpu_dev *dev = ctx->dev; +const struct rockchip_vpu_fmt *formats; +unsigned int num_fmts, i; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) +if (formats[i].fourcc == fourcc) +return &formats[i]; +return NULL ; +} + +static const struct rockchip_vpu_fmt * +rockchip_vpu_get_default_fmt (struct rockchip_vpu_ctx *ctx,bool bitstream) +{ +struct rockchip_vpu_dev *dev = ctx->dev; +const struct rockchip_vpu_fmt *formats; +unsigned int num_fmts, i; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) +if (bitstream == (formats[i].codec_mode !=RK_VPU_MODE_NONE )) +return &formats[i]; +return NULL ; +} + +static int vidioc_querycap (struct file *file,void *priv, +struct v4l2_capability *cap) +{ +struct rockchip_vpu_dev *vpu =video_drvdata (file); + +strlcpy (cap->driver, vpu->dev->driver->name,sizeof (cap->driver)); +strlcpy (cap->card, vpu->vfd_dec->name,sizeof (cap->card)); +snprintf (cap->bus_info,sizeof (cap->bus_info),"platform: %s" , + vpu->dev->driver->name); +return 0 ; +} + +static int vidioc_enum_framesizes (struct file *file,void *priv, +struct v4l2_frmsizeenum *fsize) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +const struct rockchip_vpu_fmt *fmt; + +if (fsize->index !=0 ) { +vpu_debug (0 ,"invalid frame size index (expected 0, got %d)\n" , + fsize->index); +return -EINVAL ; + } + + fmt =rockchip_vpu_find_format (ctx, fsize->pixel_format); +if (!fmt) {
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 94
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +6
-0+vpu_debug (0 ,"unsupported bitstream format (%08x)\n" , + fsize->pixel_format); +return -EINVAL ; + } + +/* This only makes sense for codec formats */ "coded formats"
OK.
Quoted 52 lines
Quoted 52 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +52
-0+if (fmt->codec_mode ==RK_VPU_MODE_NONE ) +return -EINVAL ; + + fsize->type =V4L2_FRMSIZE_TYPE_STEPWISE ; + fsize->stepwise = fmt->frmsize; + +return 0 ; +} + +static int vidioc_enum_fmt_vid_cap_mplane (struct file *file,void *priv, +struct v4l2_fmtdesc *f) +{ +struct rockchip_vpu_dev *dev =video_drvdata (file); +const struct rockchip_vpu_fmt *fmt; +const struct rockchip_vpu_fmt *formats; +int num_fmts, i, j =0 ; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) { +/* Skip compressed formats */ +if (formats[i].codec_mode !=RK_VPU_MODE_NONE ) +continue ; +if (j == f->index) { + fmt = &formats[i]; + f->pixelformat = fmt->fourcc; +return 0 ; + } + ++j; + } +return -EINVAL ; +} + +static int vidioc_enum_fmt_vid_out_mplane (struct file *file,void *priv, +struct v4l2_fmtdesc *f) +{ +struct rockchip_vpu_dev *dev =video_drvdata (file); +const struct rockchip_vpu_fmt *formats; +const struct rockchip_vpu_fmt *fmt; +int num_fmts, i, j =0 ; + + formats = dev->variant->dec_fmts; + num_fmts = dev->variant->num_dec_fmts; +for (i =0 ; i < num_fmts; i++) { +if (formats[i].codec_mode ==RK_VPU_MODE_NONE ) +continue ; +if (j == f->index) { + fmt = &formats[i]; + f->pixelformat = fmt->fourcc; +return 0 ; + } + ++j;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 85
Quoted 3 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +3
-0+ } +return -EINVAL ; +}All the functions above can be trivially generalized to be used for both encoder and decoder. Moreover, vidioc_enum_fmt_vid_{cap,out}_mplane() can be trivially merged into one function to cover both buffer types.
Right.
Quoted 115 lines
Quoted 115 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +115
-0+ +static int vidioc_g_fmt_out_mplane (struct file *file,void *priv, +struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); + +vpu_debug (4 ,"f->type = %d\n" , f->type); + + *pix_mp = ctx->src_fmt; + +return 0 ; +} + +static int vidioc_g_fmt_cap_mplane (struct file *file,void *priv, +struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); + +vpu_debug (4 ,"f->type = %d\n" , f->type); + + *pix_mp = ctx->dst_fmt; + +return 0 ; +} + +static int +vidioc_try_fmt_cap_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +const struct rockchip_vpu_fmt *fmt; +unsigned int width, height; + +vpu_debug (4 ,"%c%c%c%c\n" , + (pix_mp->pixelformat &0x7f ), + (pix_mp->pixelformat >>8 ) &0x7f , + (pix_mp->pixelformat >>16 ) &0x7f , + (pix_mp->pixelformat >>24 ) &0x7f ); + + fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); +if (!fmt) { + fmt =rockchip_vpu_get_default_fmt (ctx, false); + f->fmt.pix.pixelformat = fmt->fourcc; + } + + pix_mp->field =V4L2_FIELD_NONE ; + width =clamp (pix_mp->width, + ctx->vpu_src_fmt->frmsize.min_width, + ctx->vpu_src_fmt->frmsize.max_width); + height =clamp (pix_mp->height, + ctx->vpu_src_fmt->frmsize.min_height, + ctx->vpu_src_fmt->frmsize.max_height); +/* Round up to macroblocks. */ + width =round_up (width, ctx->vpu_src_fmt->frmsize.step_width); + height =round_up (height, ctx->vpu_src_fmt->frmsize.step_height); + +/* Fill remaining fields */ +v4l2_fill_pixfmt_mp (pix_mp, fmt->fourcc, width, height); +return 0 ; +} + +static int +vidioc_try_fmt_out_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +const struct rockchip_vpu_fmt *fmt; + + fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); +if (!fmt) { + fmt =rockchip_vpu_get_default_fmt (ctx, true); + f->fmt.pix.pixelformat = fmt->fourcc; + } + + pix_mp->num_planes =1 ; + pix_mp->field =V4L2_FIELD_NONE ; + pix_mp->width =clamp (pix_mp->width, + fmt->frmsize.min_width, + fmt->frmsize.max_width); + pix_mp->height =clamp (pix_mp->height, + fmt->frmsize.min_height, + fmt->frmsize.max_height); +/* Round up to macroblocks. */ + pix_mp->width =round_up (pix_mp->width, fmt->frmsize.step_width); + pix_mp->height =round_up (pix_mp->height, fmt->frmsize.step_height); + +/* +* For compressed formats the application can specify +* sizeimage. If the application passes a zero sizeimage, +* let's default to the maximum frame size. +*/ +if (!pix_mp->plane_fmt[0 ].sizeimage) + pix_mp->plane_fmt[0 ].sizeimage = fmt->header_size + + pix_mp->width * pix_mp->height * fmt->max_depth; +return 0 ; +} + +void rockchip_vpu_dec_reset_dst_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx) +{ +struct v4l2_pix_format_mplane *fmt = &ctx->dst_fmt; +unsigned int width, height; + + ctx->vpu_dst_fmt =rockchip_vpu_get_default_fmt (ctx, false); + +memset (fmt,0 ,sizeof (*fmt)); + + width =clamp (fmt->width, ctx->vpu_src_fmt->frmsize.min_width, + ctx->vpu_src_fmt->frmsize.max_width); + height =clamp (fmt->height, ctx->vpu_src_fmt->frmsize.min_height, + ctx->vpu_src_fmt->frmsize.max_height); + fmt->field =V4L2_FIELD_NONE ; + fmt->colorspace = V4L2_COLORSPACE_JPEG,
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 269
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +5
-0+ fmt->ycbcr_enc =V4L2_YCBCR_ENC_DEFAULT ; + fmt->quantization =V4L2_QUANTIZATION_DEFAULT ; + fmt->xfer_func =V4L2_XFER_FUNC_DEFAULT ; + +v4l2_fill_pixfmt_mp (fmt, ctx->vpu_dst_fmt->fourcc, width, height);Rather than duplicating most of the work already done in vidioc_try_fmt_*(), could we just call it here?
Yeah, I can try, see how it goes.
Quoted 52 lines
Quoted 15 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +15
-0+} + +void rockchip_vpu_dec_reset_src_fmt (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx) +{ +struct v4l2_pix_format_mplane *fmt = &ctx->src_fmt; + + ctx->vpu_src_fmt =rockchip_vpu_get_default_fmt (ctx, true); + +memset (fmt,0 ,sizeof (*fmt)); + + fmt->num_planes =1 ; + fmt->width =clamp (fmt->width, ctx->vpu_src_fmt->frmsize.min_width, + ctx->vpu_src_fmt->frmsize.max_width); + fmt->height = clamp(fmt->height, ctx->vpu_src_fmt->frmsize.min_height,drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 294
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ ctx->vpu_src_fmt->frmsize.max_height); + fmt->pixelformat = ctx->vpu_src_fmt->fourcc; + fmt->field =V4L2_FIELD_NONE ; + fmt->colorspace =V4L2_COLORSPACE_JPEG , + fmt->ycbcr_enc =V4L2_YCBCR_ENC_DEFAULT ; + fmt->quantization =V4L2_QUANTIZATION_DEFAULT ; + fmt->xfer_func =V4L2_XFER_FUNC_DEFAULT ; + + fmt->plane_fmt[0 ].sizeimage = ctx->vpu_src_fmt->header_size + + fmt->width * fmt->height * ctx->vpu_src_fmt->max_depth;Ditto.
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +24
-0+} + +static int +vidioc_s_fmt_out_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct rockchip_vpu_dev *vpu = ctx->dev; +struct vb2_queue *vq, *peer_vq; +int ret; + +/* Change not allowed if queue is streaming. */ + vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, f->type); +if (vb2_is_streaming (vq)) +return -EBUSY ; + +/* +* Since format change on the OUTPUT queue will reset +* the CAPTURE queue, we can't allow doing so +* when the CAPTURE queue has buffers allocated. +*/ + peer_vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, +V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE ); + if (vb2_is_busy(peer_vq) &&
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 322
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +4
-0+ (pix_mp->pixelformat != ctx->src_fmt.pixelformat || + pix_mp->height != ctx->src_fmt.height || + pix_mp->width != ctx->src_fmt.width)) + return -EBUSY;I'd say that in general we don't want any
S_FMT(OUT)to be allowed if CAP has buffers allocated, so maybe just checkingvb2_is_busy(peer_vq)is enough?
Hm, this has been confusing to no end for me. This check comes from s_fmt_cap in rockchip_vpu_enc.c, at the time we came to the conclusion that vb2_is_busy(peer_queue) wasn't enough.
Taking a step back, the S_FMT order is first encoded format, then raw format.
So for encoders the user is expected to do first S_FMT(CAP), second S_FMT(OUT). For decoders, first S_FMT(OUT), second S_FMT(CAP)... and that's why we are interested on a strict vb2_is_busy check.
The question is how we came to a different conclusion on the encoder.
Quoted 87 lines
Quoted 87 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +87
-0+ + ret =vidioc_try_fmt_out_mplane (file, priv, f); +if (ret) +return ret; + + ctx->vpu_src_fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); + ctx->src_fmt = *pix_mp; + +vpu_debug (0 ,"OUTPUT codec mode: %d\n" , ctx->vpu_src_fmt->codec_mode); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height); + +rockchip_vpu_dec_reset_dst_fmt (vpu, ctx); +return 0 ; +} + +static int +vidioc_s_fmt_cap_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct vb2_queue *vq; +int ret; + +/* Change not allowed if queue is streaming. */ + vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, f->type); +if (vb2_is_streaming (vq)) +return -EBUSY ; + + ret =vidioc_try_fmt_cap_mplane (file, priv, f); +if (ret) +return ret; + + ctx->vpu_dst_fmt =rockchip_vpu_find_format (ctx, pix_mp->pixelformat); + ctx->dst_fmt = *pix_mp; + +vpu_debug (0 ,"CAPTURE codec mode: %d\n" , ctx->vpu_dst_fmt->codec_mode); +vpu_debug (0 ,"fmt - w: %d, h: %d\n" , + pix_mp->width, pix_mp->height); +return 0 ; +} + +const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops = { + .vidioc_querycap = vidioc_querycap, + .vidioc_enum_framesizes = vidioc_enum_framesizes, + + .vidioc_try_fmt_vid_cap_mplane = vidioc_try_fmt_cap_mplane, + .vidioc_try_fmt_vid_out_mplane = vidioc_try_fmt_out_mplane, + .vidioc_s_fmt_vid_out_mplane = vidioc_s_fmt_out_mplane, + .vidioc_s_fmt_vid_cap_mplane = vidioc_s_fmt_cap_mplane, + .vidioc_g_fmt_vid_out_mplane = vidioc_g_fmt_out_mplane, + .vidioc_g_fmt_vid_cap_mplane = vidioc_g_fmt_cap_mplane, + .vidioc_enum_fmt_vid_out_mplane = vidioc_enum_fmt_vid_out_mplane, + .vidioc_enum_fmt_vid_cap_mplane = vidioc_enum_fmt_vid_cap_mplane, + + .vidioc_reqbufs = v4l2_m2m_ioctl_reqbufs, + .vidioc_querybuf = v4l2_m2m_ioctl_querybuf, + .vidioc_qbuf = v4l2_m2m_ioctl_qbuf, + .vidioc_dqbuf = v4l2_m2m_ioctl_dqbuf, + .vidioc_prepare_buf = v4l2_m2m_ioctl_prepare_buf, + .vidioc_create_bufs = v4l2_m2m_ioctl_create_bufs, + .vidioc_expbuf = v4l2_m2m_ioctl_expbuf, + + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event, + .vidioc_unsubscribe_event = v4l2_event_unsubscribe, + + .vidioc_streamon = v4l2_m2m_ioctl_streamon, + .vidioc_streamoff = v4l2_m2m_ioctl_streamoff, +}; + +static int rockchip_vpu_queue_setup (struct vb2_queue *vq, +unsigned int *num_buffers, +unsigned int *num_planes, +unsigned int sizes[], +struct device *alloc_devs[]) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vq); +struct v4l2_pix_format_mplane *pixfmt; +int i; + +switch (vq->type) { +case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE : + pixfmt = &ctx->dst_fmt; +break ; +case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE : + pixfmt = &ctx->src_fmt; +break ;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 413
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +4
-0+default : +vpu_err ("invalid queue type: %d\n" , vq->type); +return -EINVAL ; + }Hmm, would it make sense to have separate
vb2_queue_opsfor each queue and create helper functions, which take the necessary queue-specific data as arguments, if appropriate?
Yup, sounds good.
Quoted 84 lines
Quoted 84 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +84
-0+ +if (*num_planes) { +if (*num_planes != pixfmt->num_planes) +return -EINVAL ; +for (i =0 ; i < pixfmt->num_planes; ++i) +if (sizes[i] < pixfmt->plane_fmt[i].sizeimage) +return -EINVAL ; +return 0 ; + } + + *num_planes = pixfmt->num_planes; +for (i =0 ; i < pixfmt->num_planes; ++i) + sizes[i] = pixfmt->plane_fmt[i].sizeimage; +return 0 ; +} + +static int rockchip_vpu_buf_prepare (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); +struct vb2_queue *vq = vb->vb2_queue; +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vq); +const struct rockchip_vpu_fmt *vpu_fmt; +struct v4l2_pix_format_mplane *pixfmt; +unsigned int sz; +int ret =0 ; +int i; + +switch (vq->type) { +case V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE : + vpu_fmt = ctx->vpu_dst_fmt; + pixfmt = &ctx->dst_fmt; +break ; +case V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE : + vpu_fmt = ctx->vpu_src_fmt; + pixfmt = &ctx->src_fmt; + +if (vbuf->field ==V4L2_FIELD_ANY ) + vbuf->field =V4L2_FIELD_NONE ; +if (vbuf->field !=V4L2_FIELD_NONE ) { +vpu_debug (4 ,"field %d not supported\n" , + vbuf->field); +return -EINVAL ; + } +break ; +default : +vpu_err ("invalid queue type: %d\n" , vq->type); +return -EINVAL ; + } + +for (i =0 ; i < pixfmt->num_planes; ++i) { + sz = pixfmt->plane_fmt[i].sizeimage; +vpu_debug (4 ,"plane %d size: %ld, sizeimage: %u\n" , + i,vb2_plane_size (vb, i), sz); +if (vb2_plane_size (vb, i) < sz) { +vpu_err ("plane %d is too small for output\n" , i); + ret = -EINVAL ; +break ; + } + } + +return ret; +} + +static void rockchip_vpu_buf_queue (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + +v4l2_m2m_buf_queue (ctx->fh.m2m_ctx, vbuf); +} + +static int rockchip_vpu_start_streaming (struct vb2_queue *q,unsigned int count) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q); +enum rockchip_vpu_codec_mode codec_mode; +int ret =0 ; + +if (V4L2_TYPE_IS_OUTPUT (q->type)) + ctx->sequence_out =0 ; +else + ctx->sequence_cap =0 ; + + codec_mode = ctx->vpu_src_fmt->codec_mode; +
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 499
Quoted 2 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +2
-0+vpu_debug (4 ,"Codec mode = %d\n" , codec_mode); + ctx->codec_ops = &ctx->dev->variant->codec_ops[codec_mode];Codec mode should be a function of the OUT queue, so I think this should be also under if (
V4L2_TYPE_IS_OUTPUT()). This would make most of the code in this function specific to the OUT queue and possibly a good argument for the comment about having separate vb2 queue ops I posted above.
Yup.
Quoted 10 lines
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->start) + ret = ctx->codec_ops->start (ctx); +return ret; +} + +static void rockchip_vpu_stop_streaming (struct vb2_queue *q) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q);
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 515
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +6
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->stop) + ctx->codec_ops->stop (ctx); + +/* The mem2mem framework calls v4l2_m2m_cancel_job before CodingStyle: Multiline comments should start with one empty line.
Oops. Seems I have a tendency for this!
Quoted 24 lines
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +24
-0+* .stop_streaming, so there isn't any job running and +* it is safe to return all the buffers. +*/ +for (;;) { +struct vb2_v4l2_buffer *vbuf; + +if (V4L2_TYPE_IS_OUTPUT (q->type)) + vbuf =v4l2_m2m_src_buf_remove (ctx->fh.m2m_ctx); +else + vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx); +if (!vbuf) +break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler); +v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); + } +} + +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} +
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 544
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +5
-0+static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;Similar comment as in earlier patch. Is validate expected to correct the values or just check?
See Hans' reply.
Quoted 22 lines
Quoted 22 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +14
-0+return 0 ; +} + +const struct vb2_ops rockchip_vpu_dec_queue_ops = { + .queue_setup = rockchip_vpu_queue_setup, + .buf_prepare = rockchip_vpu_buf_prepare, + .buf_queue = rockchip_vpu_buf_queue, + .buf_out_validate = rockchip_vpu_buf_out_validate, + .buf_request_complete = rockchip_vpu_buf_request_complete, + .start_streaming = rockchip_vpu_start_streaming, + .stop_streaming = rockchip_vpu_stop_streaming, + .wait_prepare = vb2_ops_wait_prepare, + .wait_finish = vb2_ops_wait_finish, +};drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0@@ -36,6 +36,11 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" );
Quoted 8 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c module_param_named(debug, rockchip_vpu_debug, int, 0644); · line 42
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +4
-0+enum rockchip_vpu_type { +RK_VPU_ENCODER , +RK_VPU_DECODER , +};Given that we already have
ctx->is_enc, any reason not to have this represented in the same way everywhere?
The reason is that I'd rather have:
rockchip_vpu_video_device_register(vpu, RK_VPU_ENCODER);
Than:
rockchip_vpu_video_device_register(vpu, true);
We could have a vpu_type field instead of that is_enc boolean. I think the code would be even cleaner.
Quoted 15 lines
Quoted 15 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +6
-1+void *rockchip_vpu_get_ctrl (struct rockchip_vpu_ctx *ctx,u32 id) {struct v4l2_ctrl *ctrl;@@ -81,7 +86,11 @@ static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, avail_size =vb2_plane_size (&dst->vb2_buf,0 ) - ctx->vpu_dst_fmt->header_size; -if (bytesused <= avail_size) { +/* For decoders set bytesused as per the output picture. */ +if (!ctx->is_enc) { + dst->vb2_buf.planes[0 ].bytesused = + ctx->dst_fmt.plane_fmt[0 ].sizeimage; + }else if (bytesused <= avail_size) {/*
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static void rockchip_vpu_job_finish(struct rockchip_vpu_dev *vpu, · line 96
Quoted 2 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0* This works while JPEG is the only encoder this driver * supports. We will have to abstract this step, or get
avail_sizeis specific for the encoder. How about clearly separating decoder and encoder code with a separate if? It would introduce one more level of nesting, but IMHO it would be more readable, due to better separation of code paths. (Or going one step further, encoder and decoder-specific code could be moved to separate functions.)
Sounds good!
Quoted 40 lines
if (
ctx->is_enc) {
size_tavail_size= ...;
// encoder codeif (bytesused <= avail_size) { // } else { //}
} else {
// decoder code
}Quoted 28 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +24
-0@@ -159,6 +168,44 @@ static struct v4l2_m2m_ops vpu_m2m_ops = { .device_run = device_run, }; +static int +dec_queue_init (void *priv,struct vb2_queue *src_vq,struct vb2_queue *dst_vq) +{ +struct rockchip_vpu_ctx *ctx = priv; +int ret; + + src_vq->type =V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE ; + src_vq->io_modes =VB2_MMAP |VB2_DMABUF ; + src_vq->drv_priv = ctx; + src_vq->ops = &rockchip_vpu_dec_queue_ops; + src_vq->mem_ops = &vb2_dma_contig_memops; + src_vq->dma_attrs =DMA_ATTR_ALLOC_SINGLE_PAGES | +DMA_ATTR_NO_KERNEL_MAPPING ; + src_vq->buf_struct_size =sizeof (struct v4l2_m2m_buffer ); + src_vq->timestamp_flags =V4L2_BUF_FLAG_TIMESTAMP_COPY ; + src_vq->lock = &ctx->dev->vpu_mutex; + src_vq->dev = ctx->dev->v4l2_dev.dev; + src_vq->supports_requests = true; + + ret =vb2_queue_init (src_vq); +if (ret) +return ret; + + dst_vq->type =V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE ;
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static struct v4l2_m2m_ops vpu_m2m_ops = { · line 200
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +6
-0+ dst_vq->io_modes =VB2_MMAP |VB2_DMABUF ; + dst_vq->drv_priv = ctx; + dst_vq->bidirectional = true; + dst_vq->ops = &rockchip_vpu_dec_queue_ops; + dst_vq->mem_ops = &vb2_dma_contig_memops; + dst_vq->dma_attrs =DMA_ATTR_ALLOC_SINGLE_PAGES ;Any need for kernel mapping of decoder output?
Nope, I just missed this.
Thanks a lot for the detailed review!
Eze
Re: [PATCH v2 09/11] rockchip/vpu: Add decoder boilerplate
Quoted 7 lines · Ezequiel Garcia
Hey Tomasz,
Thanks for taking the time to review this carefully!
Quoted 1 line · Tomasz Figa
On Tue, Mar 5, 2019 at 4:27 AM Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]> wrote:
[snip]
Quoted 34 lines
Quoted 24 lines
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +24
-0+} + +static int +vidioc_s_fmt_out_mplane (struct file *file,void *priv,struct v4l2_format *f) +{ +struct v4l2_pix_format_mplane *pix_mp = &f->fmt.pix_mp; +struct rockchip_vpu_ctx *ctx =fh_to_ctx (priv); +struct rockchip_vpu_dev *vpu = ctx->dev; +struct vb2_queue *vq, *peer_vq; +int ret; + +/* Change not allowed if queue is streaming. */ + vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, f->type); +if (vb2_is_streaming (vq)) +return -EBUSY ; + +/* +* Since format change on the OUTPUT queue will reset +* the CAPTURE queue, we can't allow doing so +* when the CAPTURE queue has buffers allocated. +*/ + peer_vq =v4l2_m2m_get_vq (ctx->fh.m2m_ctx, +V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE ); + if (vb2_is_busy(peer_vq) &&Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 322
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +4
-0+ (pix_mp->pixelformat != ctx->src_fmt.pixelformat || + pix_mp->height != ctx->src_fmt.height || + pix_mp->width != ctx->src_fmt.width)) + return -EBUSY;I'd say that in general we don't want any
S_FMT(OUT)to be allowed if CAP has buffers allocated, so maybe just checkingvb2_is_busy(peer_vq)is enough?
Quoted 3 lines
Hm, this has been confusing to no end for me. This check comes from
s_fmt_capinrockchip_vpu_enc.c, at the time we came to the conclusion thatvb2_is_busy(peer_queue)wasn't enough.
Hmm, yeah, this is confusing indeed, especially considering that we shouldn't need width and height on the CAP queue of an encoder.
Quoted 9 lines
Taking a step back, the
S_FMTorder is first encoded format, then raw format.So for encoders the user is expected to do first
S_FMT(CAP), secondS_FMT(OUT). For decoders, firstS_FMT(OUT), secondS_FMT(CAP)... and that's why we are interested on a strictvb2_is_busycheck.The question is how we came to a different conclusion on the encoder.
I loosely recollect it having something to do with JPEG specifically, hmm...
[snip]
Quoted 20 lines
Quoted 10 lines
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +10
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->start) + ret = ctx->codec_ops->start (ctx); +return ret; +} + +static void rockchip_vpu_stop_streaming (struct vb2_queue *q) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (q);Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 515
Quoted 6 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +6
-0+ +if (V4L2_TYPE_IS_OUTPUT (q->type)) +if (ctx->codec_ops && ctx->codec_ops->stop) + ctx->codec_ops->stop (ctx); + +/* The mem2mem framework calls v4l2_m2m_cancel_job before CodingStyle: Multiline comments should start with one empty line.
Quoted 2 lines
Oops. Seems I have a tendency for this!
Actually, some subsystems use that style, e.g. net/.
Quoted 34 lines
Quoted 24 lines
Quoted 24 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +24
-0+* .stop_streaming, so there isn't any job running and +* it is safe to return all the buffers. +*/ +for (;;) { +struct vb2_v4l2_buffer *vbuf; + +if (V4L2_TYPE_IS_OUTPUT (q->type)) + vbuf =v4l2_m2m_src_buf_remove (ctx->fh.m2m_ctx); +else + vbuf =v4l2_m2m_dst_buf_remove (ctx->fh.m2m_ctx); +if (!vbuf) +break ; +v4l2_ctrl_request_complete (vbuf->vb2_buf.req_obj.req, &ctx->ctrl_handler); +v4l2_m2m_buf_done (vbuf,VB2_BUF_STATE_ERROR ); + } +} + +static void rockchip_vpu_buf_request_complete (struct vb2_buffer *vb) +{ +struct rockchip_vpu_ctx *ctx =vb2_get_drv_priv (vb->vb2_queue); + +v4l2_ctrl_request_complete (vb->req_obj.req, &ctx->ctrl_handler); +} +Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c line 544
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +5
-0+static int rockchip_vpu_buf_out_validate (struct vb2_buffer *vb) +{ +struct vb2_v4l2_buffer *vbuf =to_vb2_v4l2_buffer (vb); + + vbuf->field =V4L2_FIELD_NONE ;Similar comment as in earlier patch. Is validate expected to correct the values or just check?
Quoted 1 line
See Hans' reply.
Ack.
Quoted 34 lines
Quoted 23 lines
Quoted 23 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_dec.c new file +14
-0+return 0 ; +} + +const struct vb2_ops rockchip_vpu_dec_queue_ops = { + .queue_setup = rockchip_vpu_queue_setup, + .buf_prepare = rockchip_vpu_buf_prepare, + .buf_queue = rockchip_vpu_buf_queue, + .buf_out_validate = rockchip_vpu_buf_out_validate, + .buf_request_complete = rockchip_vpu_buf_request_complete, + .start_streaming = rockchip_vpu_start_streaming, + .stop_streaming = rockchip_vpu_stop_streaming, + .wait_prepare = vb2_ops_wait_prepare, + .wait_finish = vb2_ops_wait_finish, +};drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0@@ -36,6 +36,11 @@ module_param_named(debug, rockchip_vpu_debug, int, 0644);MODULE_PARM_DESC (debug,"Debug level - higher value produces more verbose messages" );Quoted 8 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c module_param_named(debug, rockchip_vpu_debug, int, 0644); · line 42
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +4
-0+enum rockchip_vpu_type { +RK_VPU_ENCODER , +RK_VPU_DECODER , +};Given that we already have
ctx->is_enc, any reason not to have this represented in the same way everywhere?The reason is that I'd rather have:
Quoted 9 lines
rockchip_vpu_video_device_register(vpu, RK_VPU_ENCODER);Than:
rockchip_vpu_video_device_register(vpu, true);We could have a
vpu_typefield instead of thatis_encboolean. I think the code would be even cleaner.
Sounds good to me!
Best regards,
Tomasz
PATCH v2 10/11 rockchip/vpu: Add support for non-standard controls
In reply to Ezequiel GarciaRework the way controls are registered by the driver, so it can support non-standard controls, such as those used by stateless codecs.
--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 +- .../staging/media/rockchip/vpu/rockchip_vpu.h | 24 ++++++- .../media/rockchip/vpu/rockchip_vpu_common.h | 1 + .../media/rockchip/vpu/rockchip_vpu_drv.c | 65 +++++++++++++++++-- 5 files changed, 84 insertions(+), 10 deletions(-)
drivers/staging/media/rockchip/vpu/rk3288_vpu_hw.c +1 -1
@@ -112,7 +112,7 @@ const struct rockchip_vpu_variant rk3288_vpu_variant = { .enc_fmts = rk3288_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3288_vpu_enc_fmts), .codec_ops = rk3288_vpu_codec_ops, - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .vepu_irq = rk3288_vepu_irq, .init = rk3288_vpu_hw_init, .clk_names = {"aclk", "hclk"},
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +1 -1
@@ -129,7 +129,7 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .enc_offset = 0x0, .enc_fmts = rk3399_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3399_vpu_enc_fmts), - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, .vdpu_irq = rk3399_vdpu_irq,
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +23 -1
@@ -25,6 +25,7 @@#include "rockchip_vpu_hw.h" +#define ROCKCHIP_VPU_MAX_CTRLS 32#define ROCKCHIP_VPU_MAX_CLOCKS 4#define JPEG_MB_DIM 16
@@ -34,7 +35,10 @@struct rockchip_vpu_ctx ;struct rockchip_vpu_codec_ops ; -#define RK_VPU_CODEC_JPEG BIT(0) +#define RK_VPU_JPEG_ENCODER BIT(0) +#define RK_VPU_ENCODERS 0x0000ffff + +#define RK_VPU_DECODERS 0xffff0000/** * struct rockchip_vpu_variant - information about VPU hardware variant
@@ -79,6 +83,20 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, }; +/* +* struct rockchip_vpu_ctrl - helper type to declare supported controls +* @id: V4L2 control ID (V4L2_CID_xxx) +* @is_std: boolean to distinguish standard from customs control. +* @codec: codec id this control belong to (RK_VPU_JPEG_ENCODER, etc.) +* @cfg: control configuration +*/ +struct rockchip_vpu_ctrl { +unsigned int id; +unsigned int is_std; +unsigned int codec; +struct v4l2_ctrl_config cfg; +}; +/* * struct rockchip_vpu_mc - media controller data *
@@ -169,6 +187,8 @@ struct rockchip_vpu_dev {* @dst_fmt: V4L2 pixel format of active destination format. * * @ctrl_handler: Control handler used to register controls. +* @ctrls: Array of supported controls. +* @num_ctrls: Number of controls populated in the array. * @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode.
@@ -188,6 +208,8 @@ struct rockchip_vpu_ctx {struct v4l2_pix_format_mplane dst_fmt;struct v4l2_ctrl_handler ctrl_handler; +struct v4l2_ctrl *ctrls[ROCKCHIP_VPU_MAX_CTRLS ]; +unsigned int num_ctrls;int jpeg_quality;const struct rockchip_vpu_codec_ops *codec_ops;
drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +1 -0
@@ -23,6 +23,7 @@ extern const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops;extern const struct vb2_ops rockchip_vpu_enc_queue_ops;extern const struct vb2_ops rockchip_vpu_dec_queue_ops; +void *rockchip_vpu_find_control_data (struct rockchip_vpu_ctx *ctx,unsigned int id);void rockchip_vpu_enc_reset_src_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); void rockchip_vpu_enc_reset_dst_fmt(struct rockchip_vpu_dev *vpu,
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +58 -7
84 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v2 10/11] rockchip/vpu: Add support for non-standard controls
Quoted 68 lines · Ezequiel Garcia
Rework the way controls are registered by the driver, so it can support non-standard controls, such as those used by stateless codecs.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 +- .../staging/media/rockchip/vpu/rockchip_vpu.h | 24 ++++++- .../media/rockchip/vpu/rockchip_vpu_common.h | 1 + .../media/rockchip/vpu/rockchip_vpu_drv.c | 65 +++++++++++++++++-- 5 files changed, 84 insertions(+), 10 deletions(-)drivers/staging/media/rockchip/vpu/rk3288_vpu_hw.c +1
-1@@ -112,7 +112,7 @@ const struct rockchip_vpu_variant rk3288_vpu_variant = { .enc_fmts = rk3288_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3288_vpu_enc_fmts), .codec_ops = rk3288_vpu_codec_ops, - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .vepu_irq = rk3288_vepu_irq, .init = rk3288_vpu_hw_init, .clk_names = {"aclk", "hclk"},drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +1
-1@@ -129,7 +129,7 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .enc_offset = 0x0, .enc_fmts = rk3399_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3399_vpu_enc_fmts), - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, .vdpu_irq = rk3399_vdpu_irq,drivers/staging/media/rockchip/vpu/rockchip_vpu.h +5
-1@@ -25,6 +25,7 @@#include "rockchip_vpu_hw.h" +#define ROCKCHIP_VPU_MAX_CTRLS 32#define ROCKCHIP_VPU_MAX_CLOCKS 4#define JPEG_MB_DIM 16@@ -34,7 +35,10 @@struct rockchip_vpu_ctx ;struct rockchip_vpu_codec_ops ; -#define RK_VPU_CODEC_JPEG BIT(0) +#define RK_VPU_JPEG_ENCODER BIT(0) +#define RK_VPU_ENCODERS 0x0000ffff + +#define RK_VPU_DECODERS 0xffff0000/** * struct rockchip_vpu_variant - information about VPU hardware variant @@ -79,6 +83,20 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, };
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 95
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +10
-0+/* +* struct rockchip_vpu_ctrl - helper type to declare supported controls +* @id: V4L2 control ID (V4L2_CID_xxx) +* @is_std: boolean to distinguish standard from customs control. +* @codec: codec id this control belong to (RK_VPU_JPEG_ENCODER, etc.) +* @cfg: control configuration +*/ +struct rockchip_vpu_ctrl { +unsigned int id; +unsigned int is_std;
Perhaps is_custom would make more sense? I'd expect most, if not all, of the controls to be standard. (Actually I wonder why the MPEG2 controls are not standard.)
Quoted 48 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +8
-0+unsigned int codec; +struct v4l2_ctrl_config cfg; +}; +/* * struct rockchip_vpu_mc - media controller data * @@ -169,6 +187,8 @@ struct rockchip_vpu_dev {* @dst_fmt: V4L2 pixel format of active destination format. * * @ctrl_handler: Control handler used to register controls. +* @ctrls: Array of supported controls. +* @num_ctrls: Number of controls populated in the array. * @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. @@ -188,6 +208,8 @@ struct rockchip_vpu_ctx {struct v4l2_pix_format_mplane dst_fmt;struct v4l2_ctrl_handler ctrl_handler; +struct v4l2_ctrl *ctrls[ROCKCHIP_VPU_MAX_CTRLS ]; +unsigned int num_ctrls;int jpeg_quality;const struct rockchip_vpu_codec_ops *codec_ops;drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +1
-0@@ -23,6 +23,7 @@ extern const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops;extern const struct vb2_ops rockchip_vpu_enc_queue_ops;extern const struct vb2_ops rockchip_vpu_dec_queue_ops; +void *rockchip_vpu_find_control_data (struct rockchip_vpu_ctx *ctx,unsigned int id);void rockchip_vpu_enc_reset_src_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); void rockchip_vpu_enc_reset_dst_fmt(struct rockchip_vpu_dev *vpu,drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +3
-0@@ -276,26 +276,77 @@ static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl)return 0 ; } +void *rockchip_vpu_find_control_data (struct rockchip_vpu_ctx *ctx,unsigned int id) +{ +unsigned int i;
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 291
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+ +for (i =0 ; i < ctx->num_ctrls; i++) { +if (!ctx->ctrls[i]) +continue ; +if (ctx->ctrls[i]->id == id) +return ctx->ctrls[i]->p_cur.p; + } +return NULL ; +} +
Couldn't we just use v4l2_ctrl_find() to get the control from the handler and then read the value from it?
Quoted 38 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +26
-5static const struct v4l2_ctrl_ops rockchip_vpu_ctrl_ops = { .s_ctrl = rockchip_vpu_s_ctrl, }; +static struct rockchip_vpu_ctrl controls[] = { + { + .id =V4L2_CID_JPEG_COMPRESSION_QUALITY , + .codec =RK_VPU_JPEG_ENCODER , + .is_std =1 , + .cfg = { + .min =5 , + .max =100 , + .step =1 , + .def =50 , + }, + }, +}; +static int rockchip_vpu_ctrls_setup (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx) { -v4l2_ctrl_handler_init (&ctx->ctrl_handler,1 ); -if (vpu->variant->codec &RK_VPU_CODEC_JPEG ) { -v4l2_ctrl_new_std (&ctx->ctrl_handler, &rockchip_vpu_ctrl_ops, -V4L2_CID_JPEG_COMPRESSION_QUALITY , -5 ,100 ,1 ,50 ); +int j, i, num_ctrls =ARRAY_SIZE (controls); +int allowed_codecs; + +if (ctx->is_enc) + allowed_codecs = vpu->variant->codec &RK_VPU_ENCODERS ; +else + allowed_codecs = vpu->variant->codec &RK_VPU_DECODERS ; + +if (num_ctrls >ARRAY_SIZE (ctx->ctrls)) { +vpu_err ("context control array not large enough\n" ); +return -EINVAL ; + }
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 334
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +10
-0+ +v4l2_ctrl_handler_init (&ctx->ctrl_handler, num_ctrls); + +for (i =0 , j =0 ; i < num_ctrls; i++) { +if (!(allowed_codecs & controls[i].codec)) +continue ; +if (controls[i].is_std) { +v4l2_ctrl_new_std (&ctx->ctrl_handler, &rockchip_vpu_ctrl_ops, + controls[i].id, controls[i].cfg.min, controls[i].cfg.max, + controls[i].cfg.step, controls[i].cfg.def);
No need to save the control pointer to ctx->ctrls[]? (Actually, with my comment above, we wouldn't need ctx->ctrls[] at all.)
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +7
-1+ }else { + controls[i].cfg.id = controls[i].id; + ctx->ctrls[j++] =v4l2_ctrl_new_custom (&ctx->ctrl_handler, + &controls[i].cfg,NULL ); + } +if (ctx->ctrl_handler.error) { - vpu_err("Adding JPEG control failed %d\n", + vpu_err("Adding control (%d) failed %d\n",
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 351
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +2
-1+ controls[i].id, ctx->ctrl_handler.error);v4l2_ctrl_handler_free (&ctx->ctrl_handler);return ctx->ctrl_handler.error; } } - + ctx->num_ctrls = j;return v4l2_ctrl_handler_setup (&ctx->ctrl_handler); }
Best regards,
Tomasz
Re: [PATCH v2 10/11] rockchip/vpu: Add support for non-standard controls
Quoted 68 lines · Tomasz Figa
Quoted 67 lines · Ezequiel Garcia
Rework the way controls are registered by the driver, so it can support non-standard controls, such as those used by stateless codecs.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 +- .../staging/media/rockchip/vpu/rockchip_vpu.h | 24 ++++++- .../media/rockchip/vpu/rockchip_vpu_common.h | 1 + .../media/rockchip/vpu/rockchip_vpu_drv.c | 65 +++++++++++++++++-- 5 files changed, 84 insertions(+), 10 deletions(-)drivers/staging/media/rockchip/vpu/rk3288_vpu_hw.c +1
-1@@ -112,7 +112,7 @@ const struct rockchip_vpu_variant rk3288_vpu_variant = { .enc_fmts = rk3288_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3288_vpu_enc_fmts), .codec_ops = rk3288_vpu_codec_ops, - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .vepu_irq = rk3288_vepu_irq, .init = rk3288_vpu_hw_init, .clk_names = {"aclk", "hclk"},drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +1
-1@@ -129,7 +129,7 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .enc_offset = 0x0, .enc_fmts = rk3399_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3399_vpu_enc_fmts), - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, .vdpu_irq = rk3399_vdpu_irq,drivers/staging/media/rockchip/vpu/rockchip_vpu.h +5
-1@@ -25,6 +25,7 @@#include "rockchip_vpu_hw.h" +#define ROCKCHIP_VPU_MAX_CTRLS 32#define ROCKCHIP_VPU_MAX_CLOCKS 4#define JPEG_MB_DIM 16@@ -34,7 +35,10 @@struct rockchip_vpu_ctx ;struct rockchip_vpu_codec_ops ; -#define RK_VPU_CODEC_JPEG BIT(0) +#define RK_VPU_JPEG_ENCODER BIT(0) +#define RK_VPU_ENCODERS 0x0000ffff + +#define RK_VPU_DECODERS 0xffff0000/** * struct rockchip_vpu_variant - information about VPU hardware variant @@ -79,6 +83,20 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, };
Quoted 15 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 95
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +10
-0+/* +* struct rockchip_vpu_ctrl - helper type to declare supported controls +* @id: V4L2 control ID (V4L2_CID_xxx) +* @is_std: boolean to distinguish standard from customs control. +* @codec: codec id this control belong to (RK_VPU_JPEG_ENCODER, etc.) +* @cfg: control configuration +*/ +struct rockchip_vpu_ctrl { +unsigned int id; +unsigned int is_std;Perhaps
is_customwould make more sense? I'd expect most, if not all, of the controls to be standard. (Actually I wonder why the MPEG2 controls are not standard.)
Maybe is_std is misleading. The idea was just to distinguish controls that can be registered with v4l2_ctrl_new_std, from those that need v4l2_ctrl_new_custom, not because the control is non-standard, but because it takes a custom v4l2_ctrl_config.
Maybe the is_std flag can be completely removed, and instead use cfg.elem_size to distinguish the two type of controls.
Quoted 45 lines
Quoted 45 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +8
-0+unsigned int codec; +struct v4l2_ctrl_config cfg; +}; +/* * struct rockchip_vpu_mc - media controller data * @@ -169,6 +187,8 @@ struct rockchip_vpu_dev {* @dst_fmt: V4L2 pixel format of active destination format. * * @ctrl_handler: Control handler used to register controls. +* @ctrls: Array of supported controls. +* @num_ctrls: Number of controls populated in the array. * @jpeg_quality: User-specified JPEG compression quality. * * @codec_ops: Set of operations related to codec mode. @@ -188,6 +208,8 @@ struct rockchip_vpu_ctx {struct v4l2_pix_format_mplane dst_fmt;struct v4l2_ctrl_handler ctrl_handler; +struct v4l2_ctrl *ctrls[ROCKCHIP_VPU_MAX_CTRLS ]; +unsigned int num_ctrls;int jpeg_quality;const struct rockchip_vpu_codec_ops *codec_ops;drivers/staging/media/rockchip/vpu/rockchip_vpu_common.h +1
-0@@ -23,6 +23,7 @@ extern const struct v4l2_ioctl_ops rockchip_vpu_dec_ioctl_ops;extern const struct vb2_ops rockchip_vpu_enc_queue_ops;extern const struct vb2_ops rockchip_vpu_dec_queue_ops; +void *rockchip_vpu_find_control_data (struct rockchip_vpu_ctx *ctx,unsigned int id);void rockchip_vpu_enc_reset_src_fmt (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx); void rockchip_vpu_enc_reset_dst_fmt(struct rockchip_vpu_dev *vpu,drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +0
-0@@ -276,26 +276,77 @@ static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl)return 0 ; }
Quoted 17 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 291
Quoted 13 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +13
-0+void *rockchip_vpu_find_control_data (struct rockchip_vpu_ctx *ctx,unsigned int id) +{ +unsigned int i; + +for (i =0 ; i < ctx->num_ctrls; i++) { +if (!ctx->ctrls[i]) +continue ; +if (ctx->ctrls[i]->id == id) +return ctx->ctrls[i]->p_cur.p; + } +return NULL ; +} +Couldn't we just use
v4l2_ctrl_find()to get the control from the handler and then read the value from it?
Actually, this helper is no longer in use, it's just left over code.
Quoted 43 lines
Quoted 43 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +31
-5static const struct v4l2_ctrl_ops rockchip_vpu_ctrl_ops = { .s_ctrl = rockchip_vpu_s_ctrl, }; +static struct rockchip_vpu_ctrl controls[] = { + { + .id =V4L2_CID_JPEG_COMPRESSION_QUALITY , + .codec =RK_VPU_JPEG_ENCODER , + .is_std =1 , + .cfg = { + .min =5 , + .max =100 , + .step =1 , + .def =50 , + }, + }, +}; +static int rockchip_vpu_ctrls_setup (struct rockchip_vpu_dev *vpu,struct rockchip_vpu_ctx *ctx) { -v4l2_ctrl_handler_init (&ctx->ctrl_handler,1 ); -if (vpu->variant->codec &RK_VPU_CODEC_JPEG ) { -v4l2_ctrl_new_std (&ctx->ctrl_handler, &rockchip_vpu_ctrl_ops, -V4L2_CID_JPEG_COMPRESSION_QUALITY , -5 ,100 ,1 ,50 ); +int j, i, num_ctrls =ARRAY_SIZE (controls); +int allowed_codecs; + +if (ctx->is_enc) + allowed_codecs = vpu->variant->codec &RK_VPU_ENCODERS ; +else + allowed_codecs = vpu->variant->codec &RK_VPU_DECODERS ; + +if (num_ctrls >ARRAY_SIZE (ctx->ctrls)) { +vpu_err ("context control array not large enough\n" ); +return -EINVAL ; + } + +v4l2_ctrl_handler_init (&ctx->ctrl_handler, num_ctrls); + +for (i =0 , j =0 ; i < num_ctrls; i++) { +if (!(allowed_codecs & controls[i].codec))
Quoted 9 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 334
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +5
-0+continue ; +if (controls[i].is_std) { +v4l2_ctrl_new_std (&ctx->ctrl_handler, &rockchip_vpu_ctrl_ops, + controls[i].id, controls[i].cfg.min, controls[i].cfg.max, + controls[i].cfg.step, controls[i].cfg.def);No need to save the control pointer to ctx->ctrls[]? (Actually, with my comment above, we wouldn't need ctx->ctrls[] at all.)
Right.
Quoted 14 lines
Quoted 14 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +8
-1+ }else { + controls[i].cfg.id = controls[i].id; + ctx->ctrls[j++] =v4l2_ctrl_new_custom (&ctx->ctrl_handler, + &controls[i].cfg,NULL ); + } +if (ctx->ctrl_handler.error) { -vpu_err ("Adding JPEG control failed %d\n" , +vpu_err ("Adding control (%d) failed %d\n" , + controls[i].id, ctx->ctrl_handler.error);v4l2_ctrl_handler_free (&ctx->ctrl_handler);return ctx->ctrl_handler.error; }
Quoted 8 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c static int rockchip_vpu_s_ctrl(struct v4l2_ctrl *ctrl) · line 351
Quoted 5 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +1
-1} - + ctx->num_ctrls = j;return v4l2_ctrl_handler_setup (&ctx->ctrl_handler); }Best regards,
Tomasz
Thanks,
Ezequiel
Re: [PATCH v2 10/11] rockchip/vpu: Add support for non-standard controls
Quoted 86 lines · Ezequiel Garcia
Quoted 68 lines · Tomasz Figa
Quoted 67 lines · Ezequiel Garcia
Rework the way controls are registered by the driver, so it can support non-standard controls, such as those used by stateless codecs.
Signed-off-by Ezequiel Garcia <ezequiel-ZGY8ohtN/[email protected]>--- .../media/rockchip/vpu/rk3288_vpu_hw.c | 2 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 2 +- .../staging/media/rockchip/vpu/rockchip_vpu.h | 24 ++++++- .../media/rockchip/vpu/rockchip_vpu_common.h | 1 + .../media/rockchip/vpu/rockchip_vpu_drv.c | 65 +++++++++++++++++-- 5 files changed, 84 insertions(+), 10 deletions(-)drivers/staging/media/rockchip/vpu/rk3288_vpu_hw.c +1
-1@@ -112,7 +112,7 @@ const struct rockchip_vpu_variant rk3288_vpu_variant = { .enc_fmts = rk3288_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3288_vpu_enc_fmts), .codec_ops = rk3288_vpu_codec_ops, - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .vepu_irq = rk3288_vepu_irq, .init = rk3288_vpu_hw_init, .clk_names = {"aclk", "hclk"},drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +1
-1@@ -129,7 +129,7 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .enc_offset = 0x0, .enc_fmts = rk3399_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3399_vpu_enc_fmts), - .codec = RK_VPU_CODEC_JPEG, + .codec = RK_VPU_JPEG_ENCODER, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, .vdpu_irq = rk3399_vdpu_irq,drivers/staging/media/rockchip/vpu/rockchip_vpu.h +5
-1@@ -25,6 +25,7 @@#include "rockchip_vpu_hw.h" +#define ROCKCHIP_VPU_MAX_CTRLS 32#define ROCKCHIP_VPU_MAX_CLOCKS 4#define JPEG_MB_DIM 16@@ -34,7 +35,10 @@struct rockchip_vpu_ctx ;struct rockchip_vpu_codec_ops ; -#define RK_VPU_CODEC_JPEG BIT(0) +#define RK_VPU_JPEG_ENCODER BIT(0) +#define RK_VPU_ENCODERS 0x0000ffff + +#define RK_VPU_DECODERS 0xffff0000/** * struct rockchip_vpu_variant - information about VPU hardware variant @@ -79,6 +83,20 @@ enum rockchip_vpu_codec_mode { RK_VPU_MODE_JPEG_ENC, };Quoted 15 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h enum rockchip_vpu_codec_mode { · line 95
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +10
-0+/* +* struct rockchip_vpu_ctrl - helper type to declare supported controls +* @id: V4L2 control ID (V4L2_CID_xxx) +* @is_std: boolean to distinguish standard from customs control. +* @codec: codec id this control belong to (RK_VPU_JPEG_ENCODER, etc.) +* @cfg: control configuration +*/ +struct rockchip_vpu_ctrl { +unsigned int id; +unsigned int is_std;Perhaps
is_customwould make more sense? I'd expect most, if not all, of the controls to be standard. (Actually I wonder why the MPEG2 controls are not standard.)
Quoted 8 lines
Maybe
is_stdis misleading. The idea was just to distinguish controls that can be registered withv4l2_ctrl_new_std, from those that needv4l2_ctrl_new_custom, not because the control is non-standard, but because it takes a customv4l2_ctrl_config.Maybe the
is_stdflag can be completely removed, and instead use cfg.elem_size to distinguish the two type of controls.
I see. Then I guess the flag makes sense, but perhaps it could be inverted and renamed to "has_custom_cfg"?
Best regards,
Tomasz
PATCH v2 11/11 rockchip/vpu: Add support for MPEG-2 decoding
In reply to Ezequiel GarciaFrom: Jonas Karlman <[email protected]>
Add MPEG-2 decoding, only on RK3399. Other SoCs and support for other codecs will be added in the future.
--- drivers/staging/media/rockchip/vpu/Makefile | 4 +- .../media/rockchip/vpu/rk3399_vpu_hw.c | 40 ++- .../rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c | 263 ++++++++++++++++++ .../staging/media/rockchip/vpu/rockchip_vpu.h | 9 + .../media/rockchip/vpu/rockchip_vpu_drv.c | 12 + .../media/rockchip/vpu/rockchip_vpu_hw.h | 14 + .../media/rockchip/vpu/rockchip_vpu_mpeg2.c | 61 ++++ 7 files changed, 401 insertions(+), 2 deletions(-) create mode 100644 drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c create mode 100644 drivers/staging/media/rockchip/vpu/rockchip_vpu_mpeg2.c
drivers/staging/media/rockchip/vpu/Makefile +3 -1
@@ -8,4 +8,6 @@ rockchip-vpu-y += \ rk3288_vpu_hw_jpeg_enc.o \ rk3399_vpu_hw.o \ rk3399_vpu_hw_jpeg_enc.o \ - rockchip_vpu_jpeg.o + rockchip_vpu_jpeg.o \ + rk3399_vpu_hw_mpeg2_dec.o \ + rockchip_vpu_mpeg2.o
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw.c +39 -1
@@ -55,6 +55,26 @@ static const struct rockchip_vpu_fmt rk3399_vpu_enc_fmts[] = { }, }; +static const struct rockchip_vpu_fmt rk3399_vpu_dec_fmts[] = { + { + .fourcc =V4L2_PIX_FMT_NV12 , + .codec_mode =RK_VPU_MODE_NONE , + }, + { + .fourcc =V4L2_PIX_FMT_MPEG2_SLICE , + .codec_mode =RK_VPU_MODE_MPEG2_DEC , + .max_depth =2 , + .frmsize = { + .min_width =48 , + .max_width =1920 , + .step_width =MPEG2_MB_DIM , + .min_height =48 , + .max_height =1088 , + .step_height =MPEG2_MB_DIM , + }, + }, +}; +static irqreturn_t rk3399_vepu_irq (int irq,void *dev_id) {struct rockchip_vpu_dev *vpu = dev_id;
@@ -108,6 +128,15 @@ static void rk3399_vpu_enc_reset(struct rockchip_vpu_ctx *ctx)vepu_write (vpu,0 ,VEPU_REG_AXI_CTRL ); } +static void rk3399_vpu_dec_reset (struct rockchip_vpu_ctx *ctx) +{ +struct rockchip_vpu_dev *vpu = ctx->dev; + +vdpu_write (vpu,VDPU_REG_INTERRUPT_DEC_IRQ_DIS ,VDPU_REG_INTERRUPT ); +vdpu_write (vpu,0 ,VDPU_REG_EN_FLAGS ); +vdpu_write (vpu,1 ,VDPU_REG_SOFT_RESET ); +} +/* * Supported codec ops. */
@@ -119,6 +148,12 @@ static const struct rockchip_vpu_codec_ops rk3399_vpu_codec_ops[] = { .start = rockchip_vpu_jpeg_enc_start, .stop = rockchip_vpu_jpeg_enc_stop, }, + [RK_VPU_MODE_MPEG2_DEC] = { + .run = rk3399_vpu_mpeg2_dec_run, + .reset = rk3399_vpu_dec_reset, + .start = rockchip_vpu_mpeg2_dec_start, + .stop = rockchip_vpu_mpeg2_dec_stop, + }, };/*
@@ -129,7 +164,10 @@ const struct rockchip_vpu_variant rk3399_vpu_variant = { .enc_offset = 0x0, .enc_fmts = rk3399_vpu_enc_fmts, .num_enc_fmts = ARRAY_SIZE(rk3399_vpu_enc_fmts), - .codec = RK_VPU_JPEG_ENCODER, + .dec_offset = 0x400, + .dec_fmts = rk3399_vpu_dec_fmts, + .num_dec_fmts = ARRAY_SIZE(rk3399_vpu_dec_fmts), + .codec = RK_VPU_JPEG_ENCODER | RK_VPU_MPEG2_DECODER, .codec_ops = rk3399_vpu_codec_ops, .vepu_irq = rk3399_vepu_irq, .vdpu_irq = rk3399_vdpu_irq,
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +263 -0
263 lines not on this page · raw message
drivers/staging/media/rockchip/vpu/rockchip_vpu.h +9 -0
@@ -28,6 +28,10 @@#define ROCKCHIP_VPU_MAX_CTRLS 32#define ROCKCHIP_VPU_MAX_CLOCKS 4 +#define MPEG2_MB_DIM 16 +#define MPEG2_MB_WIDTH (w) DIV_ROUND_UP(w, MPEG2_MB_DIM) +#define MPEG2_MB_HEIGHT (h) DIV_ROUND_UP(h, MPEG2_MB_DIM) +#define JPEG_MB_DIM 16#define JPEG_MB_WIDTH (w) DIV_ROUND_UP(w, JPEG_MB_DIM)#define JPEG_MB_HEIGHT (h) DIV_ROUND_UP(h, JPEG_MB_DIM)
@@ -38,6 +42,7 @@ struct rockchip_vpu_codec_ops;#define RK_VPU_JPEG_ENCODER BIT(0)#define RK_VPU_ENCODERS 0x0000ffff +#define RK_VPU_MPEG2_DECODER BIT(16)#define RK_VPU_DECODERS 0xffff0000/**
@@ -77,10 +82,12 @@ struct rockchip_vpu_variant {* enum rockchip_vpu_codec_mode - codec operating mode. * @RK_VPU_MODE_NONE: No operating mode. Used for RAW video formats. * @RK_VPU_MODE_JPEG_ENC: JPEG encoder. +* @RK_VPU_MODE_MPEG2_DEC: MPEG-2 decoder. */ enum rockchip_vpu_codec_mode {RK_VPU_MODE_NONE =-1 ,RK_VPU_MODE_JPEG_ENC , +RK_VPU_MODE_MPEG2_DEC , };/*
@@ -193,6 +200,7 @@ struct rockchip_vpu_dev {* * @codec_ops: Set of operations related to codec mode. * @jpeg_enc_ctx: JPEG-encoding context. +* @mpeg2_dec_ctx: MPEG-2-decoding context. */ struct rockchip_vpu_ctx {struct rockchip_vpu_dev *dev;
@@ -217,6 +225,7 @@ struct rockchip_vpu_ctx {/* Specific for particular codec modes. */ union {struct rockchip_vpu_jpeg_enc_hw_ctx jpeg_enc_ctx; +struct rockchip_vpu_mpeg2_dec_hw_ctx mpeg2_dec_ctx; }; };
drivers/staging/media/rockchip/vpu/rockchip_vpu_drv.c +12 -0
@@ -304,6 +304,18 @@ static struct rockchip_vpu_ctrl controls[] = { .step = 1, .def = 50, }, + }, { + .id = V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS, + .codec = RK_VPU_MPEG2_DECODER, + .cfg = { + .elem_size = sizeof(struct v4l2_ctrl_mpeg2_slice_params), + }, + }, { + .id = V4L2_CID_MPEG_VIDEO_MPEG2_QUANTIZATION, + .codec = RK_VPU_MPEG2_DECODER, + .cfg = { + .elem_size = sizeof(struct v4l2_ctrl_mpeg2_quantization), + }, }, };
drivers/staging/media/rockchip/vpu/rockchip_vpu_hw.h +14 -0
@@ -38,6 +38,14 @@ struct rockchip_vpu_jpeg_enc_hw_ctx {struct rockchip_vpu_aux_buf bounce_buffer; }; +/** +* struct rockchip_vpu_mpeg2_dec_hw_ctx +* @qtable: Quantization table +*/ +struct rockchip_vpu_mpeg2_dec_hw_ctx { +struct rockchip_vpu_aux_buf qtable; +}; +/** * struct rockchip_vpu_codec_ops - codec mode specific operations *
@@ -83,4 +91,10 @@ void rk3399_vpu_jpeg_enc_run(struct rockchip_vpu_ctx *ctx);int rockchip_vpu_jpeg_enc_start (struct rockchip_vpu_ctx *ctx);void rockchip_vpu_jpeg_enc_stop (struct rockchip_vpu_ctx *ctx); +void rk3399_vpu_mpeg2_dec_run (struct rockchip_vpu_ctx *ctx); +void rockchip_vpu_mpeg2_dec_copy_qtable (u8 *qtable, +const struct v4l2_ctrl_mpeg2_quantization *ctrl); +int rockchip_vpu_mpeg2_dec_start (struct rockchip_vpu_ctx *ctx); +void rockchip_vpu_mpeg2_dec_stop (struct rockchip_vpu_ctx *ctx); +#endif /* ROCKCHIP_VPU_HW_H_ */
drivers/staging/media/rockchip/vpu/rockchip_vpu_mpeg2.c new file +61 -0
61 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v2 11/11] rockchip/vpu: Add support for MPEG-2 decoding
Quoted 3 lines · Ezequiel Garcia
From: Jonas Karlman <[email protected]>
[snip]
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c line 85
Quoted 4 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +4
-0+ +#define PICT_TOP_FIELD 1 +#define PICT_BOTTOM_FIELD 2 +#define PICT_FRAME 3
These 3 seem to be the standard values applying to some fields of the MPEG2 controls. Why aren't they defined next to corresponding structures?
Quoted 35 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +35
-0+ +static void +rk3399_vpu_mpeg2_dec_set_quantization (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx) +{ +struct v4l2_ctrl_mpeg2_quantization *quantization; + + quantization =rockchip_vpu_get_ctrl (ctx, +V4L2_CID_MPEG_VIDEO_MPEG2_QUANTIZATION ); +rockchip_vpu_mpeg2_dec_copy_qtable (ctx->mpeg2_dec_ctx.qtable.cpu, quantization); +vdpu_write_relaxed (vpu, ctx->mpeg2_dec_ctx.qtable.dma,VDPU_REG_QTABLE_BASE ); +} + +static void rk3399_vpu_mpeg2_dec_set_buffers (struct rockchip_vpu_dev *vpu, +struct rockchip_vpu_ctx *ctx, +struct vb2_buffer *src_buf, +struct vb2_buffer *dst_buf, +const struct v4l2_mpeg2_sequence *sequence, +const struct v4l2_mpeg2_picture *picture, +const struct v4l2_ctrl_mpeg2_slice_params *slice_params) +{ +dma_addr_t forward_addr =0 , backward_addr =0 ; +dma_addr_t current_addr, addr; +struct vb2_queue *vq; + + vq =v4l2_m2m_get_dst_vq (ctx->fh.m2m_ctx); + +switch (picture->picture_coding_type) { +case V4L2_MPEG2_PICTURE_CODING_TYPE_B : + backward_addr =rockchip_vpu_get_ref (vq, slice_params->backward_ref_ts); +/* fall-through */ +case V4L2_MPEG2_PICTURE_CODING_TYPE_P : + forward_addr =rockchip_vpu_get_ref (vq, slice_params->forward_ref_ts); + } +
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c line 130
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +10
-0+/* Source bitstream buffer */ + addr =vb2_dma_contig_plane_dma_addr (src_buf,0 ); +vdpu_write_relaxed (vpu, addr,VDPU_REG_RLC_VLC_BASE ); + +/* Destination frame buffer */ + addr =vb2_dma_contig_plane_dma_addr (dst_buf,0 ); + current_addr = addr; + +if (picture->picture_structure ==PICT_BOTTOM_FIELD ) + addr +=DIV_ROUND_UP (sequence->horizontal_size,16 ) <<4 ;
Shouldn't this rather use the bytesperline taken from ctx->dst_fmt?
Also, why do we divide it (with rounding up) by 16 and then again multiply by 16 (=== << 4)? Isn't this just ALIGN(..., 16)?
Quoted 37 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +37
-0+vdpu_write_relaxed (vpu, addr,VDPU_REG_DEC_OUT_BASE ); + +if (!forward_addr) + forward_addr = current_addr; +if (!backward_addr) + backward_addr = current_addr; + +/* Set forward ref frame (top/bottom field) */ +if (picture->picture_structure ==PICT_FRAME || + picture->picture_coding_type ==V4L2_MPEG2_PICTURE_CODING_TYPE_B || + (picture->picture_structure ==PICT_TOP_FIELD && picture->top_field_first) || + (picture->picture_structure ==PICT_BOTTOM_FIELD && !picture->top_field_first)) { +vdpu_write_relaxed (vpu, forward_addr,VDPU_REG_REFER0_BASE ); +vdpu_write_relaxed (vpu, forward_addr,VDPU_REG_REFER1_BASE ); + }else if (picture->picture_structure ==PICT_TOP_FIELD ) { +vdpu_write_relaxed (vpu, forward_addr,VDPU_REG_REFER0_BASE ); +vdpu_write_relaxed (vpu, current_addr,VDPU_REG_REFER1_BASE ); + }else if (picture->picture_structure ==PICT_BOTTOM_FIELD ) { +vdpu_write_relaxed (vpu, current_addr,VDPU_REG_REFER0_BASE ); +vdpu_write_relaxed (vpu, forward_addr,VDPU_REG_REFER1_BASE ); + } + +/* Set backward ref frame (top/bottom field) */ +vdpu_write_relaxed (vpu, backward_addr,VDPU_REG_REFER2_BASE ); +vdpu_write_relaxed (vpu, backward_addr,VDPU_REG_REFER3_BASE ); +} + +void rk3399_vpu_mpeg2_dec_run (struct rockchip_vpu_ctx *ctx) +{ +struct rockchip_vpu_dev *vpu = ctx->dev; +struct vb2_v4l2_buffer *src_buf, *dst_buf; +const struct v4l2_ctrl_mpeg2_slice_params *slice_params; +const struct v4l2_mpeg2_sequence *sequence; +const struct v4l2_mpeg2_picture *picture; +u32 reg; + + src_buf =v4l2_m2m_next_src_buf (ctx->fh.m2m_ctx);
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c line 177
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +10
-0+ dst_buf =v4l2_m2m_next_dst_buf (ctx->fh.m2m_ctx); + +/* Apply request controls if any */ +v4l2_ctrl_request_setup (src_buf->vb2_buf.req_obj.req, + &ctx->ctrl_handler); + + slice_params =rockchip_vpu_get_ctrl (ctx, +V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS ); +if (!slice_params) +return ;
Shouldn't we fail the run here (i.e. return the buffers with error state)? But actually, is this even possible to happen?
Quoted 39 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +39
-0+ sequence = &slice_params->sequence; + picture = &slice_params->picture; + + reg =VDPU_REG_DEC_ADV_PRE_DIS (0 ) | +VDPU_REG_DEC_SCMD_DIS (0 ) | +VDPU_REG_FILTERING_DIS (1 ) | +VDPU_REG_DEC_LATENCY (0 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (50 )); + + reg =VDPU_REG_INIT_QP (1 ) | +VDPU_REG_STREAM_LEN (slice_params->bit_size >>3 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (51 )); + + reg =VDPU_REG_APF_THRESHOLD (8 ) | +VDPU_REG_STARTMB_X (0 ) | +VDPU_REG_STARTMB_Y (0 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (52 )); + + reg =VDPU_REG_DEC_MODE (5 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (53 )); + + reg =VDPU_REG_DEC_STRENDIAN_E (1 ) | +VDPU_REG_DEC_STRSWAP32_E (1 ) | +VDPU_REG_DEC_OUTSWAP32_E (1 ) | +VDPU_REG_DEC_INSWAP32_E (1 ) | +VDPU_REG_DEC_OUT_ENDIAN (1 ) | +VDPU_REG_DEC_IN_ENDIAN (1 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (54 )); + + reg =VDPU_REG_DEC_DATA_DISC_E (0 ) | +VDPU_REG_DEC_MAX_BURST (16 ) | +VDPU_REG_DEC_AXI_WR_ID (0 ) | +VDPU_REG_DEC_AXI_RD_ID (0 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (56 )); + + reg =VDPU_REG_RLC_MODE_E (0 ) | +VDPU_REG_PIC_INTERLACE_E (!sequence->progressive_sequence) | +VDPU_REG_PIC_FIELDMODE_E (picture->picture_structure !=PICT_FRAME ) | + VDPU_REG_PIC_B_E(picture->picture_coding_type == V4L2_MPEG2_PICTURE_CODING_TYPE_B) |
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c line 226
Quoted 10 lines
drivers/staging/media/rockchip/vpu/rk3399_vpu_hw_mpeg2_dec.c new file +10
-0+VDPU_REG_PIC_INTER_E (picture->picture_coding_type !=V4L2_MPEG2_PICTURE_CODING_TYPE_I ) | +VDPU_REG_PIC_TOPFIELD_E (picture->picture_structure ==PICT_TOP_FIELD ) | +VDPU_REG_FWD_INTERLACE_E (0 ) | +VDPU_REG_WRITE_MVS_E (0 ) | +VDPU_REG_DEC_TIMEOUT_E (1 ) | +VDPU_REG_DEC_CLK_GATE_E (1 ); +vdpu_write_relaxed (vpu, reg,VDPU_SWREG (57 )); + + reg =VDPU_REG_PIC_MB_WIDTH (DIV_ROUND_UP (sequence->horizontal_size,16 )) | + VDPU_REG_PIC_MB_HEIGHT_P(DIV_ROUND_UP(sequence->vertical_size, 16)) |
This should also come from the format. (The format should be detected based on those fields, before allocating buffers, though.)
Best regards,
Tomasz